1968 Mercury Cougar

Used grade "B" XR7 main under hood wiring harness located in the engine compartment. This harness has plugs for the head lights, voltage regulator, starter solenoid, windshield washer pump, and horns. All electrical harnesses are inspected, professionally repaired, tested, and ready to install. Grade "B" harnesses may have one or two repairs where grade "A" harnesses will be rare uncut beauties. 1968 Mercury Cougar XR7 models with Ammeter only. Not compatible with Standard model Cougar with...

Sold individually, two required per car. These are brand new, not rebuilds. Please click onto the listing of our NOS arms to see side by side comparison pictures. We do not have the 4 bolt upper ball joint version available at this time. Replaces Ford part # C7DZ-3082-A. Check out this video

Curved aluminum cable guide as seen on page 13 of the sun roof manual. Golde part number 100 413 681

Used vacuum actuator for the tilt / tilt away steering column in the Mercury Cougar, Ford Mustang or Thunderbird. This unit was used through late 1968 and 1969 and has the embedded safety starter switch in good working order. 1967 through early 1968 actuators are white, where these units are black in color. There is an active thread on the Classic Cougar Community Forum discussing tilt columns and trouble shooting. *NOTE* For tilt column service, you can contact Tony Augustine at...

Original distributor vacuum advance control valve, also called a ported vacuum switch (PVS) valve, that was installed on all Ford models including Mercury Cougar, Ford Mustang, and Torino starting in 1967. This is a used original pot metal and brass part. It has the FORD oval logo and part number C8AE-A casting.This casting number is correct for all 1968 1969 and 1970 Fords and Mercury. It was used on all engine options including 302 351C 351W 429 and 429CJ models. Because of the heavy demand...

Used ported vacuum switch with filter. Unique piece, unknown application, definitely found on a 1968. Current offering is dated 10-67 Original distributor vacuum advance control valve, also called a ported vacuum switch (PVS) valve, that was installed on all Ford models including Mercury Cougar, Ford Mustang, and Torino starting in 1967. This is a used original pot metal and brass part. It has the FORD oval logo and part number C8AE-A casting.This casting number is correct for all 1968 1969...

Reproduction vacuum hose with green and white stripes. Every effort has been made to make this hose set as close to the originals as possible. The correct thickness and rubber type means it won't kink or lose vacuum when exposed to the hot temperatures under the hood.

Reproduction set of color coded A/C rubber hoses, two T connectors and vacuum diagram.

This unit mounts on the main air chamber, it opens and closes the air vent. Made of nylon with a steel and brass plunger just like original. This unit is easy to test and can be seen by removing the glove box. Often it is the internal spring that fails on these and if your Cougar or Mustang will not easily change between blowing through the defrost ducts and the floor duct, this unit may be the culprit. Switch assembly, servo control. Replaces Ford part # C6OZ-18C311-A. *NOTE* You will need to...

This unit mounts on the main air chamber, it opens and closes the air vent. NOS or new old stock.  This unit is easy to test and can be seen by removing the glove box. Often it is the internal spring that fails on these and if your Cougar or Mustang will not easily change between blowing through the defrost ducts and the floor duct, this unit may be the culprit. Switch assembly, servo control. Tested and working, Ford box.Replaces Ford part # C6OZ-18C311-A. ...

Good used, rust free valance that will need minimal clean up before painting. These are not paint ready flawless parts, but rather 40 years old and taken from a parts car. Our reproduction front valances are spot on perfect so if you are not set on OEM please do look at them here, as they are a very good value.Ford part # C7WY-17620-A.

Good used, rust free valance with minor amounts of filler, dings and creases. These are not paint ready flawless parts, but rather 40 years old and taken from a parts car. Unless you have body work skills these are not a good value considering the amount of work needed to make them paint ready. We are very happy with the repro front valance we sell.Ford part # C7WY-17620-A. ...