All Available Parts - 1968 Mercury Cougar

Used alternator mounting bracket for any 390 / 428CJ engine without smog. This is the correct bracket and was found on 1968 390-2V or X-code Mercury Cougar and Ford Mustangs. 1969 390-4V or 390IP engines in any Mercury Cougar or Ford Mustang. If you aren't a concours person or care about correctness, this alternator installation style is the cheap way to go if you aren't planning on installing the thermactor smog components. Look in the related items list for the adjusting bracket and...

Nice reproduction of an obsolete motor mount. Left is the same as right, sold individually. This isolator is used with the 390, 427, 428 and 429 Cobra Jet engines.  Sold individually. Replaces Ford Part #: D1ZZ-6038.

These Big Block motor mounts bolt to your engine block on the top side and to the motor mount (insulator) on the bottom side. These are very correct looking and fitting reproductions, much better than the $95 version you will find in most catalogs. Fits 1967-70 Mercury Cougar and Ford Mustang with 390 or 428CJ engines, will fit passenger side of 427 side oiler engine, driver side will work with modification. Original Ford part numbers C7ZZ-6046-A R.H., C7ZZ-6046-B L.H. 427 number for the left...

Factory stock for 1968 – 1970 small block V-8’s. Mounts to the frame for supporting and mounting the small block 289, 302, 351 engines. Also known as lower engine mounting brackets. We recommend this bracket for 1967 Cougars with 289. Sold in sets. Includes one each: D0ZZ-6028-C & D0ZZ-6029-C engine frame brackets. These are better quality and fit than the reproductions. *Converting to these mounts on 1967 Cougars with 289 or 1969 – 1970 convertibles with 351 allows the use of reproduction...

Mount to the frame for supporting and mounting the FE 390, 427, and 428CJ engines. Also known as lower engine mounting brackets. For all 1967 - 1970 Cougars with 390 - 427 - 428 engines. Also includes 1967 with 289. Sold in sets. Includes one each: D0ZZ-6028-D & D0ZZ-6029-D engine frame brackets.

Factory original part for all 1968 - 1970 Cougar hardtops (non-convertible) with 289, 302, and 351 engines. Right hand bracket. Ford part number D0ZZ-6028-C.

Factory original part for all 1968 - 1970 Cougar hardtops (non-convertible) with 289, 302, and 351 engines. Left hand bracket. Ford part number D0ZZ-6029-C.

Several factory applications: 1967 - 1970 big block FE or 390, 427, or 428CJ. 1967 Cougar with 289 engines. Factory original part for all 1969 - 1970 Cougar convertibles with 351 engines. Right hand bracket. Ford part number D0ZZ-6028-D. The original 1968 part number for this bracket was C8ZZ-6028-B.

Several factory applications: 1967 - 1970 big block FE or 390, 427, or 428CJ. 1967 Cougar with 289 engines. Factory original part for all 1969 - 1970 Cougar convertibles with 351 engines. Left hand bracket. Ford part number D0ZZ-6029-D. The original 1967 part number for this bracket was C7ZZ-6029-B.

Used pair of right and left engine block plates for any 1967-69 Mercury Cougar or Ford Mustang with 390 engines, or 1968-70 428 cobra jet engines. These can be made to work on a GT-E 427 if the passenger side mount is modified for clearance.Replaces Ford part number C7ZZ-6046-A  and C7ZZ-6046-B.

Reproduction pair of engine pedestals / frame brackets for the 68 - 70 small block V-8’s. Mounts to the frame for supporting and mounting the small block 289, 302, 351 engines. Also known as lower engine mounting brackets. We recommend this bracket for 1967 Cougars with 289. Sold in sets. *Converting to these mounts on 1967 Cougars with 289 or 1969 – 1970 convertibles with 351 allows the use of reproduction engine mounts.

New bolts and nuts for attaching the engine frame stands to the frame. Fits all 1967-70 Mercury Cougar and Ford Mustang with V8 engines. 4 bolts and 4 nuts. 3/8-16 X 3 1/2 Grade 5 phosphate flange bolts.

Engine mount bolt kit for installing engine or motor mounts to the frame stands. 1967-70 Mercury Cougar or Ford Mustang V-8. Two bolts and two nuts. Quality AMK part F-753.

Reproduction pair of engine pedestals / frame brackets for the 67 - 70 big block V-8’s. Mounts to the frame for supporting and mounting the big block 390, 427 and 428 engines. Also known as lower engine mounting brackets. Sold as a pair.

Original FoMoCo used part in good condition. Casting number is C7AA-3A772-B. Fits both small and big block. This is really the way to go... Original OEM FoMoCo with all the right markings and about half the price or repro. Ford Part #: C7ZZ-3A732-B.

Perfect fit for your 289, 302, or 351w with or without AC but a hard sell when our good used rust free brackets cost less . . .

Perfect fit for use with AC or non-AC 67, 68, 69, or 70 Cougar with the 390, 427, or 428 big block.

Metal-stamped 1968 - 1970 Lower Radiator Mounting Brackets feature exact detail and proper fit. Painted dull black. Sold in Pairs. Rubber insulators not included. Replaces Ford part # C8ZZ-8052-A. Check out our video on Radiator and Fan upgrades below: ...

Our used lower cradle brackets for the 24" wide radiator will always have some amount of damage as shown. We will not send you mangled junk that is heavily rusted but they will require some amount of straightening due to their vulnerable location. These also work with the 67 small block and big block when putting in a 68-70 24" radiator but keep in mind the 1967 cars are not pre-drilled as are the 1968-1970 Mustang and Cougar.We are out of the 1970 style of brackets. We only have the two...

These Brackets are made from stamped steel just like the original, and built to Ford specifications for an exact fit. Available in correct OEM Black. customers looking for a little more flash under the hood might be interested in the highly-polished stainless steel version of this bracket! Replaces Ford Part #: C7ZZ-8A193-A. Check out our video on Radiator and Fan upgrades below: ...

When you compare the originals to the reproductions you will see minor differences. This is one of the first things you look at when you open the hood of your car. For those that are looking to keep their car original, investing a little elbow grease in clean up on these used brackets is the way to go. Consider adding the upper rubber pieces to your order, see related items.Not for use on 17-20" wide standard cooling radiators. Replaces Ford Part #: C7ZZ-8A193-A. Check out our video on...

These Brackets are made from stamped steel just like the original, and built to Ford specifications for an exact fit. Replaces Ford Part #: C7ZZ-8A193-A. Check out our video on Radiator and Fan upgrades below: ...

Sold as a pair, fits well into your upper radiator bracket used on 24" radiators 1967 - 1970. Replaces Ford part #: C7OZ-8124Check out our video on Radiator and Fan upgrades below: ...

Used on the lower mounts on the 67 - 70 big block and small block 24" wide radiator. A 1967 390 with the original radiator uses a different lower mount system which uses a different sized insulator. If you are updating your 67 with a 68 radiator you will need these. Sold as a pair. Replaces Ford part #: C8ZZ-8125. Check out our video on Radiator and Fan upgrades below: ...

BECAUSE THIS IS NOT AN ORIGINAL FORD PRODUCT, WE CANNOT RECOMMEND THIS ITEM AND NO RETURNS WILL BE ACCEPTED Shroud assembly includes custom mounting, wiring harness, and adjustable thermostat. High temperature resistant plastic with high performance electric fan to produce maximum cooling efficiency. This unit will also increased fuel economy and horsepower.  2550 CFM Fan with 30 AMP draw.  Dimensions (in inches): 15 3/4 x 26 1/2 x 3 7/8  including mounting flanges on...

C6AE-E Multiple applications over the years. 1. Later 1967 production cooling fan, generally used after 11/14/1966 on most 289 engine applications. 2. 1968 302 without air conditioning. 3. Mid year (after 11/6/1968) 1969 351 without air conditioning. 4. 1969 Early Boss 302 before 4/14/1969. 5. 1971 Cougar with 351 engine, without air conditioning. 6. **1973 Cougar 351-2V without air conditioning prior to 2/19/1973. Fan description - 4 blades and 17-1/2 inches in diameter. Ford master part...

These concours quality Zinc caps are made in America and bear all the original markings. O.E.M. details include original letter style, "S.M.C.O." and "Autolite". Pound rating is stamped on cap. Replaces Ford Part #: C7ZZ-8100-A.

These are O.E.M. replacements and will not fit most after market radiators.

Keeps the corrosive agent in your coolant from destroying vital engine components

Replacement radiator cap for the 1967 - 1973 Mercury Cougar or 1967 - 1973 Ford Mustang. This radiator cap releases pressure when the pressure exceeds 13 pound of pressure.

New 13 Pound Generic Radiator Cap with Safety Release for the 1967 - 1973 Mercury Cougar / Ford Mustang

Usually ships in 3-5 business days. For the 1967 - 1969 Small Block Cougar and Mustang and 1970 351c & 351W with AC and or heavy duty cooling package. For optimum cooling you will want to purchase a shroud as well. Most Cougars these days have been bored .030 or more and many have had performance upgrades which all lead to increased heat. Before you buy fancy wheels, valve covers or most anything else (except brakes) this should be at the top on your list. Many applications only call for a 2...

For the 1967* - 1969 FE / Big Block Cougar and Mustang and 1970 351c & 351W with AC and or heavy duty cooling package.  For optimum cooling you will want to purchase a shroud as well. Most Cougars these days have been bored .030 or more and many have had performance upgrades which all lead to increased heat.  Before you buy fancy wheels, valve covers or most anything else (except brakes) this should be at the top on your list.  Many applications only call for a 2 core but we...

Usually ships in 3-5 business days. For the 1967 - 1969 small block Cougar and Mustang with AC and or heavy duty cooling package. If you currently have the 20" wide radiator that bolts to the core support, do know you will need to buy upper and lower cradle mounts to mount this 24" wide radiator properly. For optimum cooling you will want to purchase a shroud as well. Most Cougars these days have been bored .030 or more and many have had performance upgrades which all lead to increased heat....

All steel fitting for the lower radiator tank, found on all cars with automatic transmissions. The fine threads go to the radiator and the transmission cooling line screws onto the flared fitting after installation into the radiator. Two needed per car, sold individually. Fits all years 1967-73, and all automatic transmissions. 1/2" threads go to cooling lines. 3/8" threads go into the radiator. *Note - This is an original steel fitting, not a brass reproduction. ...

Reproduction pair of brass oil cooler fittings for the Mercury Cougar or Ford Mustang that screws into the oil cooler. 1/2" threads go to cooling lines.3/8" threads go into the radiator.

 Usually ships in 3-5 business days.  New aluminum MAX CORE radiator design which maximizes the count of larger sized tubes for increased flow, generating higher cooling efficiency while offering maximum heat transferring capabilities. These are stronger than the average radiator. These radiators are more durable than the others on the market and come with a limited one year warranty. This radiator will also fit the 68 - 69 Cougar without A/C. For some helpful tips on upgrading your...

Usually ships in 3-5 business days. New aluminum MAX CORE radiator design which maximizes the count of larger sized tubes for increased flow, generating higher cooling efficiency while offering maximum heat transferring capabilities. These are stronger than the average radiator. These radiators are more durable than the others on the market and come with a limited one year warranty. Please be aware that if you are upgrading from the 20" radiator to the 24" radiator, you will need to order more...

Usually ships in 3-5 business days. New aluminum MAX CORE radiator design which maximizes the count of larger sized tubes for increased flow, generating higher cooling efficiency while offering maximum heat transferring capabilities. These are stronger than the average radiator. These radiators are more durable than the others on the market and come with a limited one year warranty. For some helpful tips on upgrading your Cougar (or Mustang) cooling system, check out our video: ...

Fits all* Ford V-8 engines, 1967 - 1973. *- NOTE: This will fit in the 351C, 351M or 400 but will not block off the port to recirculate the water back through the engine.  This can cause the engine to run hotter than desired.

Fits all* Ford V-8 engines, 1967 - 1973. *- NOTE: This will fit in the 351C, 351M or 400 but will not block off the port to recirculate the water back through the engine.  This can cause the engine to run hotter than desired.

Fits all* Ford V-8 engines, 1967 - 1973. *- NOTE: This will fit in the 351C, 351M or 400 but will not block off the port to recirculate the water back through the engine.  This can cause the engine to run hotter than desired.

Correct head-stamp. 

Cast construction with very good quality chrome. Looks great with chrome valve covers and air cleaner. For some helpful tips on upgrading your Cougar (or Mustang) cooling system, check out our video:

Reproduction aluminum cast A356 water neck for FE Big Block engines. Made from original factory blueprint, and includes the correct stamping. Will fit the 67 Big Block, but markings are correct for 68. Replaces Ford Part #: C8AE-8592-B.

Aluminum casting, made in the U.S.A. Exact copy of original, including part numbers. Fits any small block Ford 260/289/302/351W but would have only been correct on 1967 Mercury Cougar and 1965-67 Ford and Mustang with 289 engines. Has natural cast finish as original. Does not have the provision for the thermal vacuum switch starting in 1968 and newer small block Ford V-8 engines. Replaces Ford Part #: C5OE-8592-A For some helpful tips on upgrading your Cougar (or Mustang) cooling system, check...

These bright beautiful reproductions replace those corroded and rusty originals that just look nasty. Replaces Ford Part #: C8AZ-18599-C

Thermostat Housing Gasket By FEL-PRO® for the Big Block. REplaces Ford Part #: C7ZZ-8255-D.

Thermostat Housing Gasket BY FEL-PRO® Replaces Ford Part #: C5AZ-8255-A.

New water neck of thermostat housing for most 1967-70 Mercury Cougar or most other Fords with 390/427/428CJ engines. Cast aluminum without casting marks, sand cast finish. Comes with screw-in cap in place of the thermal switch if you like, includes gasket. For use with common 2-1/8 inch thermostats. *Note - very early 1967 cars were still using the 2-1/2 inch thermostats. Cutoff was around November 1966.

New water neck or thermostat housing for all 1967-70 Mercury Cougars or most other Fords with 289/302/351W engines. Cast aluminum with a shiny finish as shown. Removable plug for use with thermal vacuum switches. Comes complete with gasket.

For use in any 1967-1973 Mercury Cougar except for the 351c in stock configuration. Will work on 351c when you use this Bypass / Restriction plate conversion part.

For use in any 1967-1973 Mercury Cougar except for the 351c in stock configuration. Will work on 351c when you use this Bypass / Restriction plate conversion part. Check out this video

For use in any 1967-1973 Mercury Cougar except for the 351c in stock configuration. Will work on 351c when you use this Bypass / Restriction plate conversion part.

This fail safe thermostat can save you from costly engine damage during an overheat. They feature an exclusive technology that locks the valve open position if overheating occurs. This allows for maximum coolant flow when you need it most.

This fail safe thermostat can save you from costly engine damage during an overheat. They feature an exclusive technology that locks the valve open position if overheating occurs. This allows for maximum coolant flow when you need it most.

Used aluminum water neck of thermostat housing for most 1967-70 Mercury Cougar or most other Fords with 390/427/428CJ engines. Cast aluminum finish. Comes with threaded hole for either a screw-in cap, or thermal switch. For use with common 2-1/8 inch thermostats. Correct for 1968-70 FE engines. Not going to lie, these will show some signs of electrolysis on the inside and where the hose slips on. Additionally, we notice that the threads get a bit rotted out where the thermal switch...

Water By-Pass Hose with Autolite® logo and part number imprinted in white ink. Stamped with C2OE-8597-A. Replaces Ford Part #: C7OZ-8597

Cast Iron Water Pump for the 1967, 1968 and 1969 small block. Has six vanes on the impeller. Includes Gasket. Several other websites state that there was a mid-year change in 1969 Cougar's with a 351W, but all the documentation we have and the cars we have on hand all indicate that this change took place at the very beginning of the 70 production year so that the 351C and 351W would use the same water pump. Replaces Ford Part #: D3UZ-8501-A or C5OZ-8501. ...

Light duty OEM Replacement cast iron water pump for any Ford FE 390 / 427 / or 428CJ. Gaskets included. No Core required Replaces Ford Part #: C8AZ-8501-A.

Direct aluminum replacement for small block 1967 - 1969 cast iron pumps. Probably the last water pump you'll ever buy. Built to cool better and last longer than any other pump. Features state of the art high efficiency impeller with 16 veins and NASCAR roller type bearing. Race proven for reliability and performance. Includes Gasket. Several other websites state that there was a mid-year change in 1969 Cougar's with a 351W, but all the documentation we have and the cars we have on hand...

Water pump gasket for all 289/302/351W/351C/429 engines. This gasket is used between the water pump and water pump plate.

New water pump gasket for 1967-69 Mercury Cougar and Ford Mustang with 289/302/351W. Single gasket for sealing water pump to water pump plate only.

New water pump gasket for FE Ford engines. 1967-70 Mercury Cougar and Ford Mustang with 390/427/428CJ engines. Single gasket, two gaskets needed for installing your water pump. Price is for one gasket only.

Concours bolt for all 1968-70 Mercury Cougar and Ford products including Mustang radiator fan clutch to water pump. Sold individually, or in a set of 4. 1/2 inch hex head size an the threads are 5/16-24. This bolt is approximately 7/8" to the shoulder and 1-1/8" in total length.  Replaces Ford part # 380288-S. ...

Concours bolt set for all 1968-70 Mercury Cougar and Ford products including Mustang radiator fan clutch to water pump. 1/2 inch hex head size. Threads are 5/16-24. Also sold individually. These bolts have an approximate length of 7/8" to the shoulder and an approximate overall length of 1-1/8". ...

Concours bolt for all 1968-70 Mercury Cougar and Ford products including Mustang, radiator fan clutch to radiator cooling fan. 1/2 inch hex head size. Threads are 5/16-18. One bolt with captured split washer. Also available in a set of 4. ...

Concours bolt set for all 1968-70 Mercury Cougar and Ford products including Mustang, radiator fan clutch to radiator cooling fan. 1/2 inch hex head size. Threads are 5/16-18. Four bolts with captured split washers. Also sold individually. ...

New water pump plate gasket for the Mercury Cougar or Ford Mustang.

This is the Water Pump Bolt Kit for 1967-68 Mercury Cougar and 1965-68 Ford Mustang with the 289 or 302 engines without air conditioning. This kit includes the 11 bolts needed to mount the water pump to the motor.  This kit comes with an instruction sheet, and shows the correct placement of the bolts.

Small block Ford water pump core, suitable for rebuilding. This version has a casting number of C8AE-A. Found on many Ford 289, 302, and 351W engines from 1968-69. These do not have casting dates, and plan on sending it to a vendor that specializes in water pump rebuilding. In all likelihood, the rear cover, heater tubes, and impeller will need replacing. Occasionally they have the original non-HiPo cast iron impeller, but not always. See our other core water pump listings for other...

C8SE-B Applications: 1. 1968 289-2V engines with air conditioning or the extra cooling package. 2. 1969 Boss 302 Eliminator - after 4/14/1969. 3. *1970 Boss 302 Eliminator. 4. *1970 351 with or without air conditioning. Fan description - 5 blades and 17-5/8 inches in diameter. Ford master part number C8SZ-8600-B. Multiple dates available. *Note - 1970 Boss2 and 1970 351 owners, some time soon after the start of the year the exact same fan, but with casting number D0ZE-B was used. Check out...

Reproduction thermal fan clutch that fits 1967 - 68 289 engines, 1968 302/390/427/428CJ engines, and 1969 351W engines, all with original Ford thermal cooling fans. Slightly larger in overall diameter, (still fits fine), and retains the correct spacing from radiator. We know that these will fit Mercury Cougar and Ford Mustangs 1967-69. Closest reproduction fan clutch on the market that fits the original and reproduction C8OE-B 7 blade power fan. Hayden fan clutch with an overall height of 2.98...

Spot-On reproduction from WCCC! C8OE-B Application for 1968 includes all 390-2V, 390-4V, 427-4V, and 428 Cobra Jet engines with and without air conditioning. 1969 application is only the S code 390-4V engine, with or without air conditioning. Fan description - 7 blades and 18-1/4 inches in diameter. Fan does not include thermal fan clutch. We do sell a Hayden replacement fan clutch. Replaces Ford master part number C8OZ-8600-A. This fan will also work on many small block applications. We hope...

C7AE-D, Fan description - 5 blades and 18 inches in diameter. Ford master part number C7AE-8600-D. These 5 blade flex fans usually came on full sized Ford and Mercury cars starting in 1967. Can be used on any engine with the proper spacer with fan shroud with adequate fan opening. Check out this interesting video where they test the efficiency of factory style and aftermarket fans. Spoiler alert: the clutch fans are the most efficient! ...

Replaces Ford part # C9ZZ-8146-C. This is an excellent reproduction made from the original Ford tooling and features the original Ford logo and part number. This is for the 20" radiator. Click on images to enlarge Customer feedback found at mercurycougar.net: Boy service is just not the same as the "good old"? days. I ordered a half a trunk load of parts and pieces from West Coast Classic Cougar and about 2 hours later got a phone call informing me that the order was picked and shipped. What...

Replaces Ford part # C8ZZ-8146-A. This is a good reproduction made from the original Ford tooling but does not have the original part number or FoMoCo lettering. Has a smooth texture (unlike original) but it is made from a more durable plastic material. This is for the 24" radiator only. For some helpful tips on upgrading your Cougar (or Mustang) cooling system, check out our video: ...

Replaces Ford part # C9OZ-8146-A. This is a quality, made in America reproduction made from the original Ford tooling. This is for the 24" radiator found on Mustang, Torino and Cougar with AC or for Cougars that need extra cooling capabilities beyond what the 20" radiator / shroud can deliver. NOTE: This shroud will fit on the 67, but will only work on small block Cougars that have been retrofitted with a 1968 - 1969 24" small block radiator and mounts. For some helpful tips on upgrading your...

Fan shroud installation kit for 67 - 71 Cougars and Mustangs. Will fit 1971 Cobra Jet shrouds.

C8OZ-3C511-C Rear power steering pump support bracket. Also called the high pressure hose indexing bracket. For any 1968 Cougar or Mustang with 289 or 302 engines. OEM used part designed to maintain the position of the high pressure power steering hose from coming in contact with with moving or high heat parts. *Note - May or may not work with non-original or replacement high pressure hoses.

Replaces Ford Part # : C8OZ-3C511-B

C8OE-B Application for 1968 includes all 390-2V, 390-4V, 427-4V, and 428 Cobra Jet engines with and without air conditioning. 1969 application is only the S code 390-4V engine, with or without air conditioning. Fan description - 7 blades and 18-1/4 inches in diameter. Fan does not include thermal fan clutch. Ford master part number C8OZ-8600-A.Check out our cooling system upgrade below: ...

C8OE-8A616-B 1968 Thermal Fan Clutch - Used C8OE-8A616-B For all 1968 - 289/302 engines with air conditioning (Fan marked C6OE-G), and all 1968 - 390/427-4V/428CJ engines without air conditioning (Fan marked C8OE-B). This fan clutch can be marked C8OE-B or C8OE-C, on the hub. Ford part number C8OZ-8A616-B. Good used unit, we are unable to warranty these units. We will try to list the exact markings as they come in.

Radiator side block off plates, or radiator filler panel, for the 20 inch radiator found on standard cooling and non-air conditioned Mercury Cougar and Ford Mustang 1967 - 1968 all engines. Two per car, one on each side of the radiator. Sold individually. *NOTE* Block off plates not needed with the 24 inch radiators.

Reproduction overflow hose with ribbed outer wall. Hose length 36"

Generic hose kit that will fit the 289 or 302 for those who are not concerned about the CONCOURS look. Used on both the 20" and 24" wide radiators Replaces Ford Part #'s C4ZE-8260-A and C4ZE-8286-A. For some helpful tips on upgrading your Cougar (or Mustang) cooling system, check out our video: ...

CONCOURS radiator hose set, both upper and lower with C8ZE-8260-E and C8ZE-8266-E marked hoses. Used on both 20" and 24" inch radiators. For some helpful tips on upgrading your Cougar (or Mustang) cooling system, check out our video:

These are the best CONCOURS radiator hoses on the market. All made in the U.S.A. by Gates or Goodyear, both of which were suppliers to Ford Motor Co in the day. They are approved by Mustang Club of America. All feature special white ink markings that have been designed to adhere to the hose under normal conditions, imprint will not come off even when in contact with antifreeze. All have imprints that are very crisp and authentic. Each imprint is CONCOURS correct for the specific application...

NOTE: Some Vendors show C8ZE for the upper hose, but C8WE is the correct stamping. These are the best CONCOURS radiator hoses on the market. All made in the U.S.A. by Gates or Goodyear both suppliers to Ford Motor Co, also approved by Mustang Club of America. All feature special white ink markings that have been designed to adhere to the hose under normal conditions, imprint will not come off even when in contact with antifreeze. All have imprints that are very crisp and authentic. Each...

New silicone radiator hoses for the 67 - 68 Cougar or Mustang with the 289 or 302 engine. The hoses are made with a sturdy black silicone, which will last longer than standard rubber hoses and has a higher burst pressure rating. Includes upper and lower radiator hose, and a bypass hose. To help enhance its performance, the lower hose is nylon-reinforced and comes with a stainless steel spring, which will keep this hose from collapsing and causing other problems. Used on both the 20"...

New silicone radiator hoses for the 69 - 70 Cougar or Mustang with the 390 or 428CJ engine. The hoses are made with a sturdy black silicone, which will last longer than standard rubber hoses and has a higher burst pressure rating. Includes upper and lower radiator hose, and a bypass hose. To help enhance its performance, the lower hose is nylon-reinforced and comes with a stainless steel spring, which will keep this hose from collapsing and causing other problems. Replaces Ford...

NOTE* After comparing to the original pulley, we've found that this reproduction is approximately 3/16" shorter in overall height. New crank shaft pulley, single sheave small block Ford 289 / 302 351W engines up to 1969. Single V-belt or fan belt pulley, means for use with only the alternator. Not for use with power steering, air conditioning, or smog pump. Measures just under 6-1/4 inches in diameter. Single sheave crank shaft pulley with 3 bolt holes, excludes engines after 1970....

After-market exact reproduction of the original Ford over the counter accessory. This handy little lamp can be mounted under the hood or the trunk lid. Features a gravity switch that turns the light on when the lid is raised and off when lowered.  Replaces Ford accessory part #: C2RZ-15A700-A.

C60E-9430-E Factory original cast iron exhaust manifold for passenger side. Factory Ford manifold used in both 1967 and 1968 for all 289 and 302 engines. The heat riser stud will not be broken off like most. If this not a concern to you and want to save money please let us know!NOTE* Item has been sand blasted for pictures. The manifold you will get will be off of a parts car and will need cleaning.

C6OE-9431-F Factory original cast iron exhaust manifold for driver side. Ford manifold used on all 1967 and 1968 289/302 engines.

Used C-4 transmission 90 degree brass fitting for the rear oil cooler line. Fits 1967-68 Mercury Cougar and 1965-73 Ford Mustang where applicable.Not all of the transmissions had a 90° fitting. Compare with your cooling lines.

Small block Ford water pump core, suitable for rebuilding. This version has a casting number of C8AE-J. Found on many Ford 289, 302, and 351W engines from 1968-69. These do not have casting dates, and plan on sending it to a vendor that specializes in water pump rebuilding. In all likelihood, the rear cover, heater tubes, and impeller will need replacing. Occasionally they have the original non-HiPo cast iron impeller, but not always. See our other core water pump listings for other...

Small block Ford water pump core, suitable for rebuilding. This version has a casting number of C8OE-D. Found on many Ford 289, 302, and 351W engines from 1968-69. These do not have casting dates, and plan on sending it to a vendor that specializes in water pump rebuilding. In all likelihood, the rear cover, heater tubes, and impeller will need replacing. Occasionally they have the original non-HiPo cast iron impeller, but not always. See our other core water pump listings for other...

390-2V, 390-4V, and 427-4V factory cast iron exhaust manifold set, both a correct right and left set of matching exhaust manifolds. Indicate in the comments section if you want the early 1968 passenger side with C7OE-9428 casting or late 1968 with C8OE-9430 casting.

Factory original cast iron exhaust manifold for passenger/right side. For both S & X code 390 engines and W code 427 GT-E engines manufactured after 2/15/1968.Ford part # C8OE-9428-C.