All Available Parts - 1967 Mercury Cougar

Features the proper cover and original logos. I A S F stamped on cover. Replaces Ford Part #: C5TF-10316-A. These new voltage regulators are improved and more reliable than the units we've sold previously. NOTE: There were two versions of this regulator, the black with yellow writing was 55 amps, and the black with silver writing was 44 amps. We do not have a supplier for the black and silver version at the moment.

This is the cover only. Great for those wanting to use a reliable modern solid state regulator but look concours. Comes with rivets.Replaces Ford part number C5TF-10316-A (cover only)

Electronic voltage regulator for use on any 1967-73 Mercury Cougar or Ford Mustang or Ford. Same foot print as originals, cover can be swapped.

C7ZZ-14018-E Right side door ajar switch found on all 1967 Mercury Cougar XR7's and part of the Safety Convenience Package found optionally on Mercury Cougar or Ford Mustang. The safety convenience package or "convenience control" option included 4 warning lights either mounted on the dash (without air conditioning) or on the console. Switch assembly tag numbers as listed in the 1967 Cougar Electrical assembly manual on page 69, C7ZB-14018-A switch assembly right hand side. The engineering...

C7ZZ-14018-F Left side door ajar switch found on all 1967 Mercury Cougar XR7's and part of the Safety Convenience Package found optionally on Mercury Cougar or Ford Mustang. The safety convenience package or "convenience control" option included 4 warning lights either mounted on the dash (without air conditioning) or on the console. Switch assembly tag numbers as listed in the 1967 Cougar Electrical assembly manual on page 69, C7ZB-10B997-A switch assembly left hand. The engineering number...

Nice reproduction of the 1967 Door Jamb Switch. Replaces Ford Part #: C5AZ-17317-A Please note that most of the plastic bodied, reproduction door jamb switch currently available are for the later model cars and have smaller female plug holes that will not work on a 67.

This is a good used switch for the 1967 Mercury Cougars and Ford Mustangs that came with the 3/4" door jamb switch. This switch will be yellowed from age. Additionally, this switch for the 3/4 inch mounting hole was used on 1965-66 Full sized Ford such as Custom, 500, Galaxie, and XL models, full sized Mercury such as Monterey, S-55, Montclair, and Park Lane. 1965-67 Fairlane, 500, XL, Ranchero, and GT. 1965-67 Mercury Comet, 202, Capri, Caliente, and Cyclone. 1965-67 Ford Mustang, 1965-67...

This quality reproduction is made from the original tooling and should give you the same reliability of the original that lasted 30-40 years. Replaces Ford part number C0TZ-13A024-A

There is not a special part number for this mounting bracket that was originally spot welded to the front of the headlamp switch. We offer these for use with our reproduction headlamp switch. This adapter or retainer is needed to correctly keep the headlamp switch at the correct angle to the lower metal dash. 1967-68 Mercury Cougar.

This plastic plate / bracket is installed between dimmer switch and the floor of your 67 - 73 Cougar to provide a bit or protection for the wiring.

NOS new old stock headlight dimmer switch. This is a Motorcraft service replacement switch.  Replaces Ford part number C0TZ-13A024-A

High quality alternative to the expensive OEM switch. If you have an early 67 the plug may be the dual type which is also listed on this site. This will work with your C-4 or C-6 automatic transmission. The only real difference is that this switch does not come with the FoMoCo logo or part number on it. Replaces Ford Part #: C9ZZ-7A247-B, SW 877 

Tested and inspected neutral safety switch for the C-4 transmission installed in early 1967 Mercury Cougar and Ford Mustangs. Found on cars before build date 12/15/1966. This neutral safety switch is identified by having two plugs that plug into the single 4 pin plug, coming from the firewall. The later neutral safety switch with a single 4 pin plug will also work fine.Look for a transmission code of W on your door data plate. If your car has a code U, your original transmission was an C-6 and...

Tested and inspected neutral safety switch for the C-6 transmission installed in early 1967 Mercury Cougar and Ford Mustangs. Found on cars before build date 12/15/1966. This neutral safety switch is identified by having two plugs that plug into the single 4 pin plug, coming from the firewall.Look for a transmission code of U on your door data plate. If your car has a code W, your original transmission was an C-4 and uses a different neutral safety switch.Replaces Ford Part #: C6AZ-7A247-A, SW...

C7WB-13A769-D Same harness works for driver or passenger side, sold individually. Found on 1967 XR7 and Standard Cougars with Safety Convenience Package, console or dash mounted warning lights. C7WB-13A769-D is the tag number originally found on the harness. Wiring harness for door ajar and courtesy light. This is a grade "B" good used harness, expect minor splices, damaged rubber boots or other easily repairable minor damage.

Same harness works for driver or passenger side, sold individually. Wiring for courtesy lights, and door ajar if needed. Exact copy of 1967 XR7 wiring harness. Also used on 1967 Standard Cougar model with convenience option. 1967 and 1968 door wiring harnesses have different plugs, please order accordingly.Ford part number: C7WY-13A769-AR

C7WB-13A769-A Same harness for either side, one for each door. Found on 1967 and 1968 Standard Cougar (non-XR7's) with door courtesy lights. Wiring harness for courtesy door lights only, no door ajar. This is a grade "A" good used harness.

Reproduction radio to door harness for your 67 - 70 Cougar or Mustang.

Used pigtail that runs from the 14401 harness to either the driver or passenger side door harness for the door ajar.

Reproduction Dash to Engine Gauge Feed with push-on Post Oil Sender for the 1967 and 1968 Mercury Cougar with the 289 or 302. Red / Green stripe wire = Coil White / Red stripe wire  = Temp Red / White stripe wire = Oil lamp * Note - Verify your oil pressure switch has the connector to accept the push on boot plug. Replaces Ford Part #: C6DZ-14289-BCheck out the video below on our new gauge tester: ...

Reproduction Dash to Engine Gauge Feed with Tach and Slide-on clip Oil Sender for the 1967 and 1968 Mercury Cougar with the 289 or 302. * Note - Check the style of oil pressure connector on your engine. Replaces Ford Part #: C7DZ-14289-BCheck out the video below on our new gauge tester: ...

Reproduction Dash to Engine Gauge Feed Harness with the push-on post oil sender for the 1967 and 1968 Mercury Cougar or Mustang with the 390, 427 or 428 Big Block. Replaces Ford Part #: C7ZZ-14289-ACheck out the video below on our new gauge tester: ...

Air Conditioning Clutch Feed Wire that runs along the driver side valve cover to the clutch on the compressor. About 24 inches in total length. Starting in 1969 the female plug was of the water proof variety. Black plugs on either end.Replaces Ford Part #: C9ZB-19A885-B.

Air Conditioning Clutch Feed Wire that runs along the driver side valve cover to the clutch on the compressor. About 24 inches in total length. Starting in 1969 the female plug was of the water proof variety. Black plugs on either end.

Used headlight wiring harness for either side of the Mercury Cougar. This harness is the sub-harness that connects your headlights to the under hood harness. The Cougar uses one per side and they are identical. Sold individually.Ford part # C7WY-13076-A.When ordering, be sure to identify whether you have a 67 or a 68.

Reproduction head light wiring harness for the Mercury Cougar. These are concours quality EXACT reproductions! Every wire, every stripe and connection is exact. We have many good used wiring looms in stock for front, under dash and rear, give us a ring or email for details. Our reproduction harnesses are made by seasoned craftsmen who use only the original Ford drawings and EXACT materials. Many of the connectors are NOS.Replaces Ford part # C7WY-14290-J.

Reproduction under hood wiring harness for the Mercury Cougar. These are concours quality EXACT reproductions! Every wire, every stripe and connection is exact. We have many good used wiring looms in stock for front, under dash and rear, give us a ring or email for details. Our reproduction harnesses are made by seasoned craftsmen who use only the original Ford drawings and EXACT materials. Many of the connectors are NOS.Replaces Ford part # C7WY-14290-H.

Used standard grade "B" under hood main wiring harness located in the engine compartment. This harness has plugs for the headlights, voltage regulator, starter solenoid, windshield washer pump, and horns. All electrical harnesses are inspected, professionally repaired, tested, and ready to install. Grade "B" harnesses may have one or two repairs where the grade "A" harnesses will be rare uncut beauties. 1967 Mercury Cougar Standard models only with AMP warning light. Not compatible with XR7...

Used XR7 grade "B" main under hood wiring harness located in the engine compartment. This harness has plugs for the head lights, voltage regulator, starter solenoid, windshield washer pump, and horns. All electrical harnesses are inspected, professionally repaired, tested, and ready to install. Grade "B" harness may have one or two repairs where the grade "A" harnesses will be rare uncut beauties. 1967 Mercury Cougar XR7 models only. Not compatible with Standard model Cougar with AMPS warning...

Used standard grade "A" under hood main wiring harness located in the engine compartment. This harness has plugs for the headlights, voltage regulator, starter solenoid, windshield washer pump, and horns. All electrical harnesses are inspected, tested, and ready to install. Grade "A" harnesses are rare uncut beauties. 1967 Mercury Cougar Standard models only with AMP warning light. Not compatible with XR7 model Cougar with Ammeter. Ford part # C7WY-14290-J.

Used XR7 grade "A" main under hood wiring harness located in the engine compartment. This harness has plugs for the head lights, voltage regulator, starter solenoid, windshield washer pump, and horns. All electrical harnesses are inspected, tested, and ready to install. Grade "A" harnesses are rare uncut beauties. 1967 Mercury Cougar XR7 models only. Not compatible with Standard model Cougar with AMPS warning light. Ford part # C7WY-14290-H.

Used headlight wiring harness for either side of a very late manufactured 1968 Mercury Cougar. This harness is the sub-harness that connects your headlights to the under hood harness. The Cougar uses one per side and they are identical. Sold individually. Sometime during the very end of the 1968 Cougar manufacturing, (June 1968) the plug end changed to the style that would be used starting in 1969. Very limited supply on hand. Ford part # C7WY-13076-A. ...

This is the power feed harness that the main console wiring harness C7ZB-13B711-A plugs into, this harness runs under the carpeting to the shifter opening. We offer the main console harness and the jumper harness assembly here.Identified by a blue bullet connector to the under dash wiring harness.

Console wiring harness for 1967-68 Standard Cougar any all Mustang. This harness is for the light in the roll up garage door compartment and the rear console lights. There is a jumper wiring harness also available, that connects to the main under dash harness. See related items. Ford part number C7ZB-13B711-A. *Note - Not for Mercury Cougar XR7 models.

Used diffuser for the shift indicator lamp. This diffuser is used on the Cougar or Mustang WITH a console and attaches to the end of the light socket on your shift indicator wire harness. Both shift indicator lamps with or without a console used the same wire harness and socket, but used different diffusers. The difference in the harness from the 67 to the 68 was different colored wires and different plugs. Replacement bulbs can be found on our site as well. ...

Used diffuser for the shift indicator lamp. This diffuser is used on the Cougar or Mustang WITHOUT a console and attaches to the end of the light socket on your shift indicator wire harness. Both shift indicator lamps with or without a console used the same wire harness and socket, but used different diffusers. The only difference in the harness from the 67 to the 68 was different colored wires.

Reproduction console feed harness for the 67 - 68 Cougar or Mustang. This OEM direct fit wiring harness supplies power from the under dash harness to the console harness.

Reproduction console wiring harness for 1967-68 Standard Cougar any all Mustang. This harness is for the light in the roll up garage door compartment and the rear console lights. There is a jumper wiring harness also available, that connects to the main under dash harness. See related items. Replaces Ford part number C7ZB-13B711-A. *Note - Not for Mercury Cougar XR7 models.

New console wiring harness for 1967-68 Standard Cougar any all 1967-68 Ford Mustang. This harness is for the light in the roll up garage door compartment and the rear console lights. There is a jumper wiring harness also available, that connects to the main under dash harness. See related items. Ford part number C7ZB-13B711-A. *Note - Not for Mercury Cougar XR7 models.

C7WB-13A769-A Same harness for either side, one for each door. Found on 1967 and 1968 Standard Cougar (non-XR7's) with door courtesy lights. Wiring harness for courtesy door lights only, no door ajar. This is a grade "B" good used harness, expect minor splices, damaged rubber boots or other easily repairable minor damage.

Tested and inspected neutral safety switch for the C-4 and C-6 transmissions installed in 1967-69 Mercury Cougar and 1967-69 Ford Mustangs. Look for a transmission code of W or U on your door data plate. If your car has a code X, your original transmission was an FMX and uses a different neutral safety switch.Replaces Ford Part #: C7DP-7A247-A, C8ZP-7A247, C9ZZ-7A247-C, SW 887.Fits: 1967 Mercury Cougar1968 Mercury Cougar1969 Mercury Cougar 1967 Ford Mustang1968 Ford Mustang1969...

This reproduction neutral safety switch is for the early 67 Cougars with a C-4 automatic transmission. It has two small plugs as opposed to one large like the later version we also have listed. Ford part #  C4AZ-7A247-C, SW 368.

New Old Stock neutral safety switch for the C-4 transmission installed in early 1967 Mercury Cougar and 1966-67 Ford Mustangs. Found on cars before build date 12/15/1966. This neutral safety switch is identified by having two plugs that plug into the single 4 pin plug, coming from the firewall. The later neutral safety switch with a single 4 pin plug will also work fine.Look for a transmission code of W on your door data plate. If your car has a code U, your original transmission was an C-6...

Correct for Cougars built after 1-2-07 with the stop lamp relay located under dash. XR7 and standard Cougars use the same rear wiring harness to the taillights. This tail light harness is a grade "A" premium grade harness that is not sun damaged, spliced or damaged in anyway. The 1157 taillight bulb sockets are sold separately.*NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's...

1968 differs in the plugs that connect to the sequential unit. Correct for Cougars built after 1-2-67 with the stop lamp relay located under dash. XR7 and standard Cougars use the same rear wiring harness to the tail lights This is a grade "B" harness that may have minor sun damage, splices or other cosmetic defects. The 1157 taillight bulb sockets are sold separately.*NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the...

3/4" wide and 60' long. This tape resembles the tape you would find on bicycle handle bars or a hockey stick but is in fact different. The taillight harness uses this type of tape as well as portions of the under dash harness. Not used in modern applications and getting rather hard to find these days.NOTE: This is FRICTION tape not adhesive tape. It is coated with rubber and relies on friction with itself to wrap wires. It does not stick to the wires. This was one of the first types of...

Wiring harness for the low fuel sending units on 1967 Mercury Cougar XR7 and standard models with low fuel warning light. The Safety Convenience Option included a low fuel warning light. This harness has two wires which attach to the three prongs on the 1967 C7ZF-9275-D low fuel sending units.1967 and 1968 will interchange, 1967 has a plastic shielding on the end of the wire loom that is under the car. 1968 version does not have this shielding. We suspect that the Ford part number is...

These small rubber protectors slip over the metal tabs in the trunk that hold the taillight wiring loom to the body. They protect the wiring from abrasion, and are often missing. Sold individually.

Used early grade "B" under dash wire harnesses. There are two versions of this harness, and early and a late version. This early version is for Cougars built prior to 1/3/1967, the late version is for Cats built after. In January of 1967 Mercury eliminated the stop lamp relay and integrated it into the sequential main turn signal relay, known as the K8-K9 relay. The early and late versions will not interchange with each other. All our harnesses will be inspected, professionally repaired,...

Here is a real treat! This grade "A" harness is a very hard to find harness as the XR7 was not even introduced until mid-model year of 1967. The 67 harness has several differences from the 68 which keeps it from being able to interchange with any other year or model. We also have this harness in B grade condition, tested with some obvious repairs, but all in working condition. Harness can carry a tag marked C7WB-14401-G, -L, -N.*NOTE* If you send us your old used under dash harness, you will...

This is actually the correct 2 inch screw for the 1968, as opposed to the 1 3/4 inch screw that would have come in the 67. With the added length this screw is less likely to pull out of the firewall than the 67 screw was. Fits Standard and XR7. Sold individually.

Brake switch jumper wire, 4 inch long extension. Bridges the under dash wiring harness and the brake light switch. Not used on many cars, we suspect that it was used on the assembly line when the brake switch plug didn't reach the brake switch. Adding one of these jumpers, saved time from re-routing the under dash wiring harness. Ford master part numbers: C5AZ-14489-C, C8ZA-13K408-A and C8ZZ-13K408-A

This wiring harness has an included lamp socket that plugs into your instrument cluster just below your right turn signal light.This 1967 harness attaches to the ignition switch, and the seat belt reminder relay (sold separately). Tested harness includes 1895 bulb, 7-1/2 amp fuse.

Used under dash harness repair plug and pigtail for the head light switch for the Mercury Cougar Standard or XR7. This is part of the 14401 main under dash wiring harness.*NOTE* The individual wires can be removed from the block and other wires can be inserted if your car has different options.

Used late grade "B" under dash wire harnesses. There are two versions of this harness, and early and a late version. This late version is for Cougars built after to 1/3/1967, the early version is for Cats built prior to. In January of 1967 Mercury eliminated the stop lamp relay and integrated it into the sequential main turn signal relay, known as the K8-K9 relay. The early and late versions will not interchange with each other. All our harnesses will be inspected, professionally repaired,...

Used late grade "A" under dash wire harnesses. There are two versions of this harness, and early and a late version. This late version is for Cougars built after to 1/3/1967, the early version is for Cats built prior to. In January of 1967 Mercury eliminated the stop lamp relay and integrated it into the sequential main turn signal relay, known as the K8-K9 relay. The early and late versions will not interchange with each other. All our harnesses will be inspected, professionally repaired,...

Used wiring pigtail that runs from the main 14401 harness to the low fuel light on your 67 - 68 XR7 Cougar.

This the main under dash harness for the convenience panel that connects to the door harness (door ajar) and low fuel harness. Fits 1967 Mercury Cougar and Ford Mustang. Has low fuel lead for Cougar on driver side, plug for low fuel on passenger side for Mustang. One plug is unused, depending upon application. This is a rare option, indicator lights would be installed in the center section of the dash panel. Unless, air conditioning was installed. If the car had factory A/C and the...

Brake switch jumper wire, 4 inch long extension. Bridges the under dash wiring harness and the brake light switch. Not used on many cars, we suspect that it was used on the assembly line when the brake switch plug didn't reach the brake switch. Adding one of these jumpers, saved time from re-routing the under dash wiring harness. This jumper can also be used to repair bad stop light connectors on 1967-70 Cougars and Mustangs (and other Fords) by cutting off the male end and splicing it...

This the light connector harness for the dash convenience panel that connects to the door harness (door ajar) and low fuel harness. Fits both 1967 and 1968 Mercury Cougar and Ford Mustang. Has low fuel lead for Cougar on driver side, plug for low fuel on passenger side for Mustang. One plug is unused, depending upon application. This is a rare option, indicator lights would be installed in the center section of the dash panel. Unless, air conditioning was installed. If the car...

Aluminum spacer used on 289/302/351 engines for mounting the alternator. Length is 1-5/8 inches long, mounts between the alternator and the cylinder head.

Used alternator adjusting bracket for early 1967 Mercury Cougar or 1965-67 Ford Mustang with 289 V-8 engines. Very early style which is a carryover from the 1965-66 289 alternator bracket. The difference of this C5AE-10145-A alternator bracket and the C7OE-10145-A bracket is the C7OE bracket has a slightly rounded off end to prevent contact with some of the larger diameter water pump pulleys. To be safe, we recommend the C7OE-10145-A bracket for clearance purposes. Ford part number...

Used alternator bracket for any 1967 Mercury Cougar or Ford Mustang with 289 engine, but without factory smog pump. Replaces Ford part number C6OE-10156-A.*Trivia - the only difference between this bracket, and the C8OE-10156-A bracket is the thickness of the steel. Either one will work on 289/302/351W engines 1966-69.

67 - 68 Cougar tail light wiring harness repair plug end. We clip these with a generous amount of wiring (6 plus inches) that allows you the car owner to repair your own tail light wiring harnesses. This is a black 5 pin plug, that is designated P79 in the wiring diagram. This plug plugs into the emergency warning relay flasher in the trunk. We are offering all of the various plugs for repairs.Good for both STD and XR7 models*NOTE* Need help diagnosing a Cougar turn signal problem? Victor...

1967 and 1968 Mercury Cougar tail light wiring harness repair plug end. We clip these with a generous amount of wiring (6 plus inches) that allows you the car owner to repair your own tail light wiring harnesses. This is a black 4 pin plug, that is designated J77 in the wiring diagram. This plug plugs into the sequential turn signal motor in the trunk. We are offering all of the various plugs for repairs. *NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s...

Used alternator adjusting bracket for any 1967-68 Mercury Cougar or 1967-68 Ford Mustang with 289 or 302 V-8 engines. C7OE-10145-A stamped bracket has a slightly rounded off end to prevent contact with some of the larger diameter water pump pulleys from previous years. Ford part number C7OE-10145-A.*Trivia - All 3 small block alternator adjusting brackets from 1965-1969 will fit most all 289 / 302 / 351W engines unless your engine has one of the larger pulleys. ...

Nice reproduction of an obsolete motor mount. Left is the same as right, sold individually. This isolator is used with the 390, 427, 428 and 429 Cobra Jet engines.  Sold individually. Replaces Ford Part #: D1ZZ-6038.

These Big Block motor mounts bolt to your engine block on the top side and to the motor mount (insulator) on the bottom side. These are very correct looking and fitting reproductions, much better than the $95 version you will find in most catalogs. Fits 1967-70 Mercury Cougar and Ford Mustang with 390 or 428CJ engines, will fit passenger side of 427 side oiler engine, driver side will work with modification. Original Ford part numbers C7ZZ-6046-A R.H., C7ZZ-6046-B L.H. 427 number for the left...

Mount to the frame for supporting and mounting the FE 390, 427, and 428CJ engines. Also known as lower engine mounting brackets. For all 1967 - 1970 Cougars with 390 - 427 - 428 engines. Also includes 1967 with 289. Sold in sets. Includes one each: D0ZZ-6028-D & D0ZZ-6029-D engine frame brackets.

Several factory applications: 1967 - 1970 big block FE or 390, 427, or 428CJ. 1967 Cougar with 289 engines. Factory original part for all 1969 - 1970 Cougar convertibles with 351 engines. Right hand bracket. Ford part number D0ZZ-6028-D. The original 1968 part number for this bracket was C8ZZ-6028-B.

Several factory applications: 1967 - 1970 big block FE or 390, 427, or 428CJ. 1967 Cougar with 289 engines. Factory original part for all 1969 - 1970 Cougar convertibles with 351 engines. Left hand bracket. Ford part number D0ZZ-6029-D. The original 1967 part number for this bracket was C7ZZ-6029-B.

Used pair of right and left engine block plates for any 1967-69 Mercury Cougar or Ford Mustang with 390 engines, or 1968-70 428 cobra jet engines. These can be made to work on a GT-E 427 if the passenger side mount is modified for clearance.Replaces Ford part number C7ZZ-6046-A  and C7ZZ-6046-B.

C7AZ-3C511-B Rear power steering pump support bracket. Also called the high pressure hose indexing bracket. For any 1967 Cougar or Mustang with any V8 engine. OEM used part designed to maintain the position of the high pressure power steering hose from coming in contact with with moving or high heat parts. *Note - May or may not work with non-original or replacement high pressure hoses.

Sold as a pair, these are one year only brackets used with the over-sized 390 radiator. We also have the 1967 unique rubber insulators listed as well. These brackets have a 2" opening. Check out our video on Radiator and Fan upgrades below: ...

One year only, 1967 390 only used brackets for use in conjunction with original 1967 radiator. If you are putting a reproduction radiator in your 1967 then the 1968-1970 lower brackets are what you are after. Check out our video on Radiator and Fan upgrades below: ...

Used on big block radiators, unique to 1967. Sold as a pair. Replaces Ford part number C3AZ-8125 Check out our video on Radiator and Fan upgrades below: ...

These Brackets are made from stamped steel just like the original, and built to Ford specifications for an exact fit. Available in correct OEM Black. customers looking for a little more flash under the hood might be interested in the highly-polished stainless steel version of this bracket! Replaces Ford Part #: C7ZZ-8A193-A. Check out our video on Radiator and Fan upgrades below: ...

When you compare the originals to the reproductions you will see minor differences. This is one of the first things you look at when you open the hood of your car. For those that are looking to keep their car original, investing a little elbow grease in clean up on these used brackets is the way to go. Consider adding the upper rubber pieces to your order, see related items.Not for use on 17-20" wide standard cooling radiators. Replaces Ford Part #: C7ZZ-8A193-A. Check out our video on...

These Brackets are made from stamped steel just like the original, and built to Ford specifications for an exact fit. Replaces Ford Part #: C7ZZ-8A193-A. Check out our video on Radiator and Fan upgrades below: ...

Sold as a pair, fits well into your upper radiator bracket used on 24" radiators 1967 - 1970. Replaces Ford part #: C7OZ-8124Check out our video on Radiator and Fan upgrades below: ...

Used on the lower mounts on the 67 - 70 big block and small block 24" wide radiator. A 1967 390 with the original radiator uses a different lower mount system which uses a different sized insulator. If you are updating your 67 with a 68 radiator you will need these. Sold as a pair. Replaces Ford part #: C8ZZ-8125. Check out our video on Radiator and Fan upgrades below: ...

BECAUSE THIS IS NOT AN ORIGINAL FORD PRODUCT, WE CANNOT RECOMMEND THIS ITEM AND NO RETURNS WILL BE ACCEPTED Shroud assembly includes custom mounting, wiring harness, and adjustable thermostat. High temperature resistant plastic with high performance electric fan to produce maximum cooling efficiency. This unit will also increased fuel economy and horsepower.  2550 CFM Fan with 30 AMP draw.  Dimensions (in inches): 15 3/4 x 26 1/2 x 3 7/8  including mounting flanges on...

C6AE-E Multiple applications over the years. 1. Later 1967 production cooling fan, generally used after 11/14/1966 on most 289 engine applications. 2. 1968 302 without air conditioning. 3. Mid year (after 11/6/1968) 1969 351 without air conditioning. 4. 1969 Early Boss 302 before 4/14/1969. 5. 1971 Cougar with 351 engine, without air conditioning. 6. **1973 Cougar 351-2V without air conditioning prior to 2/19/1973. Fan description - 4 blades and 17-1/2 inches in diameter. Ford master part...

New bolts and nuts for attaching the engine frame stands to the frame. Fits all 1967-70 Mercury Cougar and Ford Mustang with V8 engines. 4 bolts and 4 nuts. 3/8-16 X 3 1/2 Grade 5 phosphate flange bolts.

Engine mount bolt kit for installing engine or motor mounts to the frame stands. 1967-70 Mercury Cougar or Ford Mustang V-8. Two bolts and two nuts. Quality AMK part F-753.

Original FoMoCo used part in good condition. Casting number is C7AA-3A772-B. Fits both small and big block. This is really the way to go... Original OEM FoMoCo with all the right markings and about half the price or repro. Ford Part #: C7ZZ-3A732-B.

Perfect fit for your 289, 302, or 351w with or without AC but a hard sell when our good used rust free brackets cost less . . .

Perfect fit for use with AC or non-AC 67, 68, 69, or 70 Cougar with the 390, 427, or 428 big block.

C7ZE-8A616-B For all 1967 - 289 engines with air conditioning (fan marked C6OE-G), and all 390 engines (fan marked C6OE-F), without air conditioning. Fan clutch marked C7ZE-B on the hub. Ford part number C7OZ-8A616-C. Ford Motorcraft number YB-107. Good used clutch, we are unable to warranty these units.

C7ZE-8A616-A Application is 1967 S code 390 with air conditioning. Marked C7ZE-A on the hub. Ford part number C7OZ-8A616-A. Ford Motorcraft number YB-106. Good working clutch, we are unable to warranty these units.

Reproduction thermal fan clutch that fits 1967 - 68 289 engines, 1968 302/390/427/428CJ engines, and 1969 351W engines, all with original Ford thermal cooling fans. Slightly larger in overall diameter, (still fits fine), and retains the correct spacing from radiator. We know that these will fit Mercury Cougar and Ford Mustangs 1967-69. Closest reproduction fan clutch on the market that fits the original and reproduction C8OE-B 7 blade power fan. Hayden fan clutch with an overall height of 2.98...

Good quality "concours" shroud that is more durable than the "horse hair" textured originals. Fits the 1967 390 & 428 Mustang, Cougar & Shelby with the factory 23" radiator or our aftermarket 24" radiator. Opening measures about 19-11/16" in diameter. Since this shroud interchanges with the 1967 Shelby GT500 428 PI, good used shrouds are very expensive and hard to find.  If you happen to have an original you would like to sell we would be very interested in hearing from...

Replaces Ford part # C9ZZ-8146-C. This is an excellent reproduction made from the original Ford tooling and features the original Ford logo and part number. This is for the 20" radiator. Click on images to enlarge Customer feedback found at mercurycougar.net: Boy service is just not the same as the "good old"? days. I ordered a half a trunk load of parts and pieces from West Coast Classic Cougar and about 2 hours later got a phone call informing me that the order was picked and shipped. What...

Replaces Ford part # C9OZ-8146-A. This is a quality, made in America reproduction made from the original Ford tooling. This is for the 24" radiator found on Mustang, Torino and Cougar with AC or for Cougars that need extra cooling capabilities beyond what the 20" radiator / shroud can deliver. NOTE: This shroud will fit on the 67, but will only work on small block Cougars that have been retrofitted with a 1968 - 1969 24" small block radiator and mounts. For some helpful tips on upgrading your...

Reproduction concours correct fasteners and clips for attaching the fan shroud to the radiator on 1967 Mercury Cougar and Ford Mustang with original style radiators and fan shrouds. 

Fan shroud installation kit for 67 - 71 Cougars and Mustangs. Will fit 1971 Cobra Jet shrouds.

Used C-4 transmission 90 degree brass fitting for the rear oil cooler line. Fits 1967-68 Mercury Cougar and 1965-73 Ford Mustang where applicable.Not all of the transmissions had a 90° fitting. Compare with your cooling lines.

Fits all* Ford V-8 engines, 1967 - 1973. *- NOTE: This will fit in the 351C, 351M or 400 but will not block off the port to recirculate the water back through the engine.  This can cause the engine to run hotter than desired.

Fits all* Ford V-8 engines, 1967 - 1973. *- NOTE: This will fit in the 351C, 351M or 400 but will not block off the port to recirculate the water back through the engine.  This can cause the engine to run hotter than desired.

Fits all* Ford V-8 engines, 1967 - 1973. *- NOTE: This will fit in the 351C, 351M or 400 but will not block off the port to recirculate the water back through the engine.  This can cause the engine to run hotter than desired.