My Lists
Login
Subtotal
$0.00
Shipping
Tax
Discount
Total
This "offshore" set of low quality reproduction windshield mouldings / trim are sold only as a set. You will not want to mix and match these reproduction units with used because the color and quality will not match. These are guaranteed to look bad and fit even worse. No returns, no exchanges. We strongly suggest that you purchase our restored or good used set. And yes, these are the exact same trim parts supplied by the other vendors with a completely different description. Check out our...
This is one of the best small block Ford V-8 books on the market. It covers 260-289-302 V8 engines. Carburetor numbers, distributor numbers, covers all engine brackets, pulleys, and parts of Ford small block engines. 100's of pages with pictures, casting numbers, and explanations by year. A must for concours detailing and year by year correctness. Author Bob Mannel, covers small block V8 engines and components 1962-69. References all Ford cars that these engines came in. Mustang, Cougar,...
Used pinion yoke for an 8 inch rear end on any 1967-68 Mercury Cougar or 1967-73 Ford Mustang. 25 splines Ford says it is for a 1260 U-Joint. Part cleaned for pictures, used parts shipped the way they come off of the cars. Shipped bare, no hardware included.Ford part number C3OZ-4851-A.
Used pinion yoke for an 9 inch rear end on any 1967-73 Mercury Cougar or 1967-73 Ford Mustang. 1310 U-Joint. Part cleaned for pictures, used parts shipped the way they come off of the cars. Shipped bare, no hardware included. Ford part number C3AZ-4851-L.
Ford OEM kit for rebuilding your power steering control valve on any 1962-70 Ford or Mercury. All parts in photo are included. We also have the complete rebuild kit available. NOS power steering control valve repair kit. Ford part number C2AZ-3A553-A.
Reproduction ring gear for 157 tooth fly wheels and flex plates as found on certain 289 and 302 engines in 1967-68 Mercury Cougar and Ford and Mustang. Quality new ring gear, check the Youtube for installation instructions.Replaces Ford part number C2OZ-6384-B.
NOS new old stock Motorcraft water temperature sending unit, fits Ford 289, 302, 390, 427, 428CJ. 260° stamped, for Mercury Cougar 1967-69, and Ford Mustang 1966-69. Ford number C6DZ-10884-B. *Note - these are specifically NOT for 1969 351W. Ford had a unique part number for that one engine.... and we don't stock that one. Sorry. Check out the video below on our new gauge tester Check out our video on replacing the fuel system on a '68 Cougar! ...
Used Autolite water temperature sending unit, fits Ford 289, 302, 390, 427, 428CJ. 260° stamped, for Mercury Cougar 1967-69, and Ford Mustang 1966-69. Ford number C6DZ-10884-B. *Note - these are specifically NOT for 1969 351W. Ford had a unique part number for that one engine.... and we don't stock that one. Sorry. Check out the video below on our new gauge tester Check out our video on replacing the fuel system on a '68 Cougar! ...
Set of reproduction Ford Top Loader 4 speed shift rods for 1967-68 Mercury Cougar or Ford Mustang with 289 or 302 engines only.
New red permanent strength thread locker for your project. This is a must have item if you are reassembling your pride and joy after restoration or just changing out parts. Often times, the vibrations from these antiques can vibrate loose the fasteners used to hold it together. If you use this, you can rest assured that your Merc or Ford will not fall apart from fasteners that have vibrated loose.
Metal rod that hooks to the carburetor linkage and the accelerator pedal bellcrank, or shaft. Hooked end goes into the carburetor linkage, threaded end to the rear. Application 1967 Mercury Cougar and 1964 - 1967 Ford Mustang with 289 engines. Ford part number C5ZZ-9A-702-A. A rod end clevis clip is needed for attachment to the carburetor - see part B7A-9826-A. *Note - not for use with factory cruise control.
This hand held cart was used by service stations or garages to hold spools or bare wire to make them easily accessible when needed. There's a handy foot long ruler painted into it to quickly and easily measure lengths of wire. The design and style suggests that it could be from anytime between 1940 and 1970, making it a valuable collectors item for car enthusiasts. Condition is used, but aside from obvious defects and patina (see photos above, random wire included),...