All Available Parts - 1969 Ford Mustang

Exact Copies Made From the Original Supplier to Ford Motor Co. U.S.A. Made. Ramp-Lok Features a Special Conical Washer Designed Specifically for Exhaust Manifolds.

Exact Copies Made From the Original Supplier to Ford Motor Co. U.S.A. Made. Ramp-Lok Features a Special Conical Washer Designed Specifically for Exhaust Manifolds

Exact Copies Made From the Original Supplier to Ford Motor Co. U.S.A. Made. Ramp-Lok Features a Special Conical Washer Designed Specifically for Exhaust Manifolds.

Exact Copies Made From the Original Supplier to Ford Motor Co. U.S.A. Made. Ramp-Lok Features a Special Conical Washer Designed Specifically for Exhaust Manifolds.

Reproduction Exhaust Manifold Pipe Stud Kit for the 260, 289, 302, 351 and 1969 390GT 1967 - 1972 Mercury Cougar and Ford Mustang

Kit has the longer studs for use with spacers or butterfly spacers, between 390 and 428CJ passenger side exhaust manifolds and H pipe flange.

Reproduction exhaust pipe to exhaust manifold nut for the Mercury Cougar or Ford Mustang and they are sold individually.Ford part # 376420-S.

This filter fits all V8 Mercury Cougars or Ford Mustangs with the Autolite Carburetor. This filter fits all 1967 - 1973 Cougars except for the following: the Boss 302 4V, 390 4V, 427 4V, 428 4V and the 429 4V. Will also fit many 6 cyl Mustang applications. These Filters are precisely designed and engineered to meet OEM requirements and fitment. Delivering high efficiency filtration, our filters meet modern engine demands for maximum fuel flow. Prevents harmful contaminants such as dirt,...

This filter ONLY fits the following Ford Holley 1967 - 1973 Cougars: the Boss 302 4V, 390 4V, 427 4V, 428 4V and the 429 4V. Will also fit many Mustang applications. This is a service replacement filter, it has D2AE-9155-AA stamped on the body of the filter. Replaces Ford Part #: C7OZ-9155-A, Filter FG-19 and C9AZ-9155-B,  FG-39.

Factory cast aluminum two barrel carburetor spacer plate. Positions carburetor above intake manifold for proper linkage operation. With PCV fitting at rear. Fits all Ford 2 barrel carburetors, bore size is 1-5/8 inches in diameter. ...

Factory cast aluminum four barrel carburetor spacer plate, 1-1/8" tall. Positions carburetor above intake manifold for proper linkage operation. With PCV fitting at rear. *excludes Boss 302 Eliminator ...

Good Quality spacer that measures 1 1/8" tall. Comes with PCV hose clamp and vacuum port cap. This was used on all 289, 302, 351w motors with a 4V carburetor.

New carburetor gasket for all 289-4V, 302-4V, and 351-4V, Mercury and Ford cars from 1964-1970. Same gasket used between intake manifold and spacer, and spacer and carburetor. Sold individually, 2 required for complete installation with Ford 1 inch factory spacer and correct numbered Autolite 4300 carburetors.

New 390 2BBL Carburetor spacer gasket for the 1968 X code 390-2V engine. Two needed per installation, one on both sides of the spacer plate.

New carburetor gasket for most 1967-73 2 barrel carburetors. 289/302/351W/351C engines. Replaces Ford Part #: C3AZ-9447-B *Excludes 1968 X code 390-2V premium fuel engines.

Reproduction 8 Cylinder 2V Choke Thermostat Shield for the 1967 and 1968 Mercury Cougar and Ford Mustang

Correct fiberglass insulation, fittings, rubber hose and S clip.

C9OE-9431-B 351W factory original cast iron exhaust manifold for driver side. For all 1969 and 1970 Windsor 351's.

C9OE-9430-B 351W factory original cast iron exhaust manifold for passenger side. For all 1969 and 1970 Windsor 351's. This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit of 50% of our web price for parts delivered in hand or by carrier to our Brooks, Oregon location. If you're not interested in store credit, just shoot us an email and we will let you know if it's is something we can pay...

Used FoMoCo 24 inch small block radiator. This is for a 1969 Mercury Cougar or Ford Mustang with 351-2V or 351-4V and FMX (automatic code X) transmission. Used core radiator for recoring and restoration. Typical Dearborn installed assembly line radiator. Lower tank does have the connections for installing the transmission cooling lines. Various dates available, please choose one of the dates in the comments section of your order. Current dates available: 8LD (4th week Nov 1968), 9BA (1st week...

Reproduction overflow hose with smooth outer wall. Hose length 36"

C8OE-9430-D 428 Cobra Jet factory original cast iron exhaust manifold for passenger side. *Spacer required for installation.

New carburetor gasket for 67 - 70 Cougar or Mustang with 390 or 428 cobra jet engines and Ford numbered Holley carburetors. One or two needed per installation (with or without spacer plate) sold individually.

Concourse Correct Hollow Left Rear Stud for the Carburetor Vacuum port to the C6 transmission modulator hose Replaces Part # 382768-S8

Exact OEM standards and specifications. Correct fiberglass insulation, fittings, rubber hose and S clip.

Exact OEM standards and specifications. Correct fiberglass insulation, fittings, rubber hose and S clip.

These steel tubes are made to exacting O.E.M. standards and specifications. All choke tubes have the proper fiberglass insulation, fittings, rubber hose, and S-clip. Also includes cold air tube when applicable.

15/16" thick aluminum with 5/8" heater nipples & 5/8" PCV hose nipple on rear. Casting number C9ZE-9A589-A.

New carburetor spacer plate gasket for all 1969 Mercury Cougar or Ford Mustang with S code 390-4V or 390IP original Autolite Carburetors. Additionally it fits all Ford installed Holley carburetors. This is the carburetor spacer to manifold gasket. Upper gasket between spacer and carburetor also available. This carburetor gasket also works well with most aftermarket Holley and Edelbrock carburetors.

New carburetor spacer gasket, goes between the intake manifold and spacer plate. 1969 S code 390-4V or 390IP. Upper gasket, spacer plate to carburetor here.

Basic kit for rebuilding your Ford Autolite or Motorcraft square bore 4300 or 4 barrel carburetor. This kit is not for later spreadbore carburetors. Spreadbore carburetors have much larger secondary venturis. See picture.

Basic kit for rebuilding a 1967-70 Holley model 4150 4 barrel carburetor. Includes illustrated instructions. Holley packaged renew kit. This kit is not for model 4160 or other Holley carburetors. See pictures of Holley 4150 below. Click on images to enlarge. ...

Basic kit for rebuilding your Ford Autolite or Motorcraft 2100 or 2 barrel carburetor. Covers all factory 2 barrel carburetors on any 1967-73 Mercury Cougar and Ford Mustang with Autolite or Motorcraft 2100 carburetors. Excludes later 2150 carburetors.

This filter ONLY fits the following 1967 - 1973 Cougars: the Boss 302 4V, 390 4V, 427 4V, 428 4V and the 429 4V. Will also fit many Mustang applications. Replaces Ford Part #: C7OZ-9155-A, Filter FG-19.

This filter fits all V8 Mercury Cougars or Ford Mustangs with the Autolite Carburetor. This filter fits all 1967 - 1973 Cougars except for the following: the Boss 302 4V, 390 4V, 427 4V, 428 4V and the 429 4V. Will also fit many 6 cyl Mustang applications. These Filters are precisely designed and engineered to meet OEM requirements and fitment. Delivering high efficiency filtration, our filters meet modern engine demands for maximum fuel flow. Prevents harmful contaminants such as dirt,...

1969 351-2V Autolite 2100 carburetor, automatic FMX transmission - All 50 states. C9ZF-B stamped on the carburetor base, 1.23" venturi size and 356 cfm. Core, rebuildable carburetor with proper numbers. We don't always have the factory Ford Autolite tag that was affixed to the top. PCV spacer plates also available and required for stock air cleaner clearance on top of engine.

1969 390-4V Autolite 4300 carburetor, 3 or 4 speed manual transmission - All 50 states. C9ZF-E stamped on the carburetor base, 1.25" venturi size and 600 cfm. Core, rebuildable carburetor with proper numbers. We don't always have the factory Ford Autolite tag that was affixed to the top.

1969 351-2V Autolite 2100 carburetor, 3 or 4 speed manual transmission - All 50 states. C9ZF-A stamped on the carburetor base, 1.23" venturi size and 356 cfm. Core, rebuildable carburetor with proper numbers. We don't always have the factory Ford Autolite tag that was affixed to the top. PCV spacer plates also available and required for stock air cleaner clearance on top of engine.

Rebuilt 1969 428CJ-4V Holley 4150 carburetor, automatic C6 transmission - all 50 states. C9AF-9510-N stamped on the carburetor air horn. Holley list #4280, 735 cfm, Date Code 951 (May 1969, 1st week). Rebuilt carburetor with proper numbers, we don't always have the factory Ford Autolite tag that was affixed to the top. *Includes Super Cobra Jet.

This 7 piece kit is for 1969 or 1970 Mercury Cougar and Ford Mustang with the 351 Windsor and a 2 Barrel Carburetor, where the choke tube enters through the bottom of the choke housing.

This 8 piece kit is for 1969 or 1970 Mercury Cougar and Ford Mustang with the 351 Windsor and a 4 Barrel Carburetor, where the choke tube enters through the side of the choke housing.

This 8 piece kit is for 1969 or 1970 Mercury Cougar and Ford Mustang with the 351 Windsor and a 4 Barrel Carburetor, where the choke tube enters through the side of the choke housing.

This is the steel tube that goes from the carburetor to the fuel pump if you have a 289 or 302, and you have the Autolite 4300 4 Barrel Carburetor. Stainless Steel.

This is the steel tube that goes from the carburetor to the fuel pump on the 289 or 302 with the AutoLite 4300 4 barrel carberator. Original steel version.

This is the steel tube that goes from the carburetor to the fuel pump. Available in original steel or stainless steel.

Reproduction fuel line for the Boss 429 engine standard steel construction. Application would be for all Ford and Mercury products with Z code Boss 429 engines. Bent for use with factory intake manifolds, OEM Carter fuel pump, and OEM installed Holley carburetor. Can be carefully bent to fit most applications where replacement fuel pumps or Holley 4150 carburetors are used.

This is the steel tube that goes from the carburetor to the fuel pump. Designed to fit OEM Carter X fuel pump with screws holding two halves together. Modern Carter fuel pumps are crimped and will need some bending of this tube to fit. Please see item 11761 tube for use with generic Carter fuel pumps.

This is the steel tube that goes from the carburetor to the fuel pump. Designed for vehicles LO-VOL fuel pump, fits 67 - 70 Mustang, 67 Cougar 390, 67 Fairlane and Torino.

This is the single prong version fuel sending unit for 69 Cougars and Mustangs. Cougars equipped with the convenience control package, and the XR7's used a three prong version. The function however is not as good as original but adequate and usually will work for years. If you have an original, often times it's just the float that needs replacing, so don't be quick to discard your original.Check out the video below on our new gauge tester: ...

Often when your fuel gauge is acting up, this is the culprit, not the gauge or sending unit. The problem with these brass floats, is that after year of being in contact with fuel, they will begin to corrode and disintegrate. We suggest going with the new foam floats. They are fuel resistant and will last longer. Find it here. Replaces Ford part #C0AZ-9202-B.Check out the video below on our new gauge tester: ...

Replaces Ford part #C0AZ-9A307-B.

Good used ring with only surface rust and no obvious gouges.

This part is installed on all XR7 fuel sending units and Cougars and Mustangs with the optional Convenience Control Package. Low quality off shore part that requires soldering to your fuel sending unit. This is a temperature sensing device that activates when the fuel level drops enough to expose the unit at which point the circuit is closed and the low fuel light comes on. Commonly referred to as a Thermister / Thermistor / Low Fuel Sending Unit.

This is the stainless steel, single prong version fuel sending unit for 69 Cougars and Mustangs. Cougars equipped with the convenience control package, and the XR7's used a three prong version. These units are better than original being made from stainless. The function however is not as good as original but adequate and usually will work for years. If you have an original, often times it's just the float that needs replacing, so don't be quick to discard your original. Check...

Exclusive to WCCC, here's our reproduction in-tank, fuel sending unit with the low fuel option. Good for all 1969 Mercury Cougar XR7's and all Ford Mustangs with 16 gallon fuel tanks. This is a reproduction of a 1969 fuel sending unit with 3 prongs (2 electrical and 1 alignment prong). The original Ford casting number was C9WF-9275-C. This unit comes with a new 3/8 inch filter, brass float, and sending unit gasket. These are completely interchangeable on all 1969 20 gallon fuel tanks. *Note -...

Often when your fuel gauge is acting up, this is the culprit, not the gauge or sending unit. The benefit of using this foam float, is that sometimes the hollow brass float will leak, causing a bad reading. This foam version of the float is fuel resistant and will never leak. Replaces Ford part #C0AZ-9202-B.Check out the video below on our new gauge tester: ...

This is the stainless steel, single prong version fuel sending unit with 1/4"  return line for 69 Cougars and Mustangs. Cougars equipped with the convenience control package, and the XR7's used a three prong version. These units are better than original being made from stainless. The function however is not as good as original but adequate and usually will work for years. If you have an original, often times it's just the float that needs replacing, so don't be quick to...

This option requires that you send your core in advance. Your core gets rebuilt and returned. If you don't have a core, WCCC has come across a few from our wrecking yard, give us a call to discuss details. Our service is to rebuild your sending unit. A quality core is required. Yes, we can rebuild other than 1967-73 Mercury Cougar and Ford Mustang sending units. 1967-1980 Ford / Mercury / Lincoln sending units accepted. See our related listing for non-low fuel sending unit rebuilding. A...

This option requires that you send your core in advance. Your core gets rebuilt and returned. If you don't have a core, WCCC has come across a few from our wrecking yard, give us a call to discuss details. Our service is to rebuild your standard fuel sending unit. A quality core is required. Yes, we can rebuild other than 1967-73 Mercury Cougar and Ford Mustang sending units. 1967-1980 Ford sending units accepted. See our related listing for low fuel sending unit rebuilding. A quality...

Used retaining ring for the fuel sending unit or vent on 1971 and newer tanks. Fits a little tighter than the reproduction rings. Ford part #C0AZ-9A307-B.

Reproduction pair of moulding / outer dash trim pieces for the 69 - 70Cougar or Mustang.Replaces Ford Part #C9ZZ-6504718

Used cigar or cigarette lighter threaded retainer with ground lug. Fits any 1969 Mercury Cougar and Ford Mustang with factory installed console. The ground lug is needed for the heating element in the socket. The consoles are made of plastic and use the common socket designed for steel dashes. This retainer is part of C9MB-15055-A socket and retainer assembly. 

Used cigar or cigarette lighter threaded retainer with ground lug. Fits any 1969 Mercury Cougar and Ford Mustang with factory installed console. The ground lug is needed for the heating element in the socket. The consoles are made of plastic and use the common socket designed for steel dashes. This retainer is part of C9MB-15055-A socket and retainer assembly. 

Used ignition switch bezel for any 1969 Mercury Cougar, 1969 Ford Mustang and many other 1969 Ford and Mercury cars with the ignition switches on the dash panel. Good used part, little or no imperfections in the chrome, good value compared to the reproduction. Replaces Ford part #: C9AZ-11584-A.

Used angled chrome spacer for any 1969 Mercury Cougar or Ford Mustang. Good used part with very good chrome plating, usually one of the small locating tabs will be broken off of the back. Still a great value compared to the reproduction, and installs fine without the one tab on the back. Replaces Ford part number C9ZZ-11574-A.

Used wiper switch bezel for any 1969-70 Mercury Cougar or Ford Mustang. This is a used bezel that has been inspected for pits in the chrome. This used unit will likely have one of the rear orientation tabs broken, but other than that it will be a good used part. Excellently priced, compared to the reproduction. Here is a helpful youtube video on how to go about removing a headlight switch from a Cougar or Mustang. Replaces Ford part #: C9ZZ-10852. ...

Used bezel retaining nut for the windshield wiper switch on any 1971-73 Mercury Cougar or Ford Mustang. Good threads and very good chrome on the front as shown. Replaces Ford part number D1ZB-17512-A.

Reproduction nut or inner bezel for the headlamp switch on all 1969-70 Mercury Cougar and Ford Mustangs. Replaces Ford part number C9ZZ-11650-A .

Used dash pad clip for any 1969-70 Mercury Cougar or Ford Mustang. This clip attaches to the steel dash assembly. The lower portion of the padded dashes just above the glove box door and steering column is where they attach. We have seen anywhere from 2-4 or zero of these clips installed on 1969-70 Cougars. According to Bill Q. these clips prevent the sharp dash pad screws from coming into contact with wiring or wiring harnesses. His go-around is to only use blunt screws (without a point) for...

Reproduction glove box cable. Keep in mind that the screws included in this kit are not correct. The original screws had a shoulder near the top to allow the cable to swing freely. You can find them here.Replaces Ford part #: C9ZZ-6506008.

Correct for Mustang and Cougar without factory Air Conditioning. This has the larger sized storage compartment compared to the air conditioning version. Replaces Ford part number C9ZB-6506015.*Note - This box will not work with cars that have original air conditioning.

Nice reproduction globe box door button bezel for all 1967-70 Mercury Cougar and Ford Mustangs. We do sell used to, see related.Replaces Ford part number C6OB-62060A12.

Glove box or glove compartment light with switch. Fits 1969 Mercury Cougar, 1969 Ford Mustang. Used switch and wiring assembly, tested and working. 1969 has a part number C9WB-14413-B on the wire. Will work on a 1970 Cougar or Mustang. The wire on the 1969 pigtail is a larger gauge than the 1970 equivalent.Fits 69 CougarFits 69 Mustang

Correct reproduction for the Mustang and Cougar without factory Air Conditioning. This has the larger sized storage compartment compared to the A/C version. However, we recommend going with our good used Glove Box Liner as it will be a better fit.

Used hinge for any 1969-70 Mercury Cougar or Ford Mustang. Comes as shown, we select the best hinges to inventory, most will have the original dash color paint.Replaces Ford part number C9ZZ-6506050-A.

Correct reproduction for 1969 and 1970 Mustang and Cougar with factory Air Conditioning. This has the smaller sized storage compartment compared to the non air conditioning version. Replaces Ford part number C9ZB-6506015.

Reproduction glove box light switch for the 69 - 70 Cougar or the 69 - 73 Mustang.

Used glove box catch for any 1969-73 Mercury Cougar or Ford Mustang. Ford part number C9AZ-6206064-A.

Used glove box cable. Cable only, screws sold separately. The original screws had a shoulder near the top to allow the cable to swing freely. You can find them here. and we have original used.Replaces Ford part #: C9ZZ-65060A08.

Reproduction glove box latch for the 69 - 70 Cougar or Mustang. Unlike the originals, this is a keyless latch.

These original clips hold better than the reproductions we offer. If you look closely you will see the angle bend is more acute on the originals. For you 71-73 owners with warped panels you will want to use these original clips (at least along the bottom edge) for a tighter hold. The only difference between this spring clip and the other used one we offer is the presence of the foam spacer pad. Helpful tip: Door panel clips install sliding toward the rear of the vehicle. ...

In addition to fastening your door panels to the doors, these spring clips are also used to fasten your pads to the console on 67 - 68 models and seat backs to seats 67 - 70. Coated to prevent rust. Sold Individually. These do not hold as well as our originals but do function fine for most applications. 23 - 29 used per door panel, depending upon model. Helpful tip: Door panel clips install sliding toward the rear of the vehicle. ...

Package of 30 spring clips. These are also used to fasten your pads to the console on 1967-68 Models. Coated to prevent rust. 23 - 29 used per door panel, depending upon model. Helpful tip: Door panel clips install sliding toward the rear of the vehicle.

These go into your door panel, behind the inside door release handle. High quality reproduction, no excuses! Sold individually, available only in black. Includes mounting clips. Fits all Cougar door panels 1969 - 1970. Unfortunately these are not good items to paint as constant contact will scratch. We have several sets of good used pairs in a variety of colors, contact us for availability. Replaces Ford part #: C9ZZ-65226A34-A. "Don is one of the best guys you will ever deal with in the...

Good used metal portion of the door panel. If yours is bent, or you're doing custom door panels, you will need these. Fits 1969-70 Mercury Cougar and Ford Mustang.

Good used metal portion of the door panel. If yours is bent, or you're doing custom door panels, you will need these. Fits 1969-70 Mercury Cougar and Ford Mustang.

Package of 100 spring clips. These are also used to fasten your pads to the console on 1967-68 Models. Coated to prevent rust. 23 - 29 used per door panel, depending upon model. Helpful tip: Door panel clips install sliding toward the rear of the vehicle.

Although many would disagree, these are in my opinion average quality. "BUT" they are the best reproductions currently available. The inner portion where your fingers go have too sharp of edges and they do not hold up nearly as well as the originals do. We also have used in most colors available. Thank You Don and WCCC, Copy Cat's almost done! Yesterday was such a nice day I took Copy Cat out to Show Don and Lin the final (almost) product. Without their patience and understanding along with a...

Although some would disagree, these are in our opinion average at best quality. However, they are the best reproductions currently available. The inner portion where your fingers go have too sharp of edges and they do not hold up nearly as well as the originals do. The white color on these has an almost grey tint, these are a good neutral color to paint to whatever color you need. No return on these as we insure you up front you will not be impressed. Thank You Don and WCCC, Copy Cat's almost...

Although many would disagree, these are in my opinion average quality. "BUT" they are the best reproductions currently available. The inner portion where your fingers go have too sharp of edges and they do not hold up nearly as well as the originals do. We also have used in most colors available. Thank You Don and WCCC, Copy Cat's almost done! Yesterday was such a nice day I took Copy Cat out to Show Don and Lin the final (almost) product. Without their patience and understanding along with a...

Although some would disagree, these are in our opinion average at best quality. However, they are the best reproductions currently available. The inner portion where your fingers go have too sharp of edges and they do not hold up nearly as well as the originals do. The white color on these has an almost grey tint, these are a good neutral color to paint to whatever color you need. No return on these as we insure you up front you will not be impressed. Thank You Don and WCCC, Copy Cat's almost...

New screw with a correct 3/8 inch hex head for installing all armrests for all years.

Although many would disagree, these are in my opinion average quality. "BUT" they are the best reproductions currently available. The inner portion where your fingers go have too sharp of edges and they do not hold up nearly as well as the originals do. We also have used in most colors available. Thank You Don and WCCC, Copy Cat's almost done! Yesterday was such a nice day I took Copy Cat out to Show Don and Lin the final (almost) product. Without their patience and understanding along with a...

Although many would disagree, these are in my opinion average quality. "BUT" they are the best reproductions currently available. The inner portion where your fingers go have too sharp of edges and they do not hold up nearly as well as the originals do. We also have used in most colors available. Thank You Don and WCCC, Copy Cat's almost done! Yesterday was such a nice day I took Copy Cat out to Show Don and Lin the final (almost) product. Without their patience and understanding along with a...

Although many would disagree, these are in my opinion average quality. "BUT" they are the best reproductions currently available. The inner portion where your fingers go have too sharp of edges and they do not hold up nearly as well as the originals do. We also have used in most colors available. Thank You Don and WCCC, Copy Cat's almost done! Yesterday was such a nice day I took Copy Cat out to Show Don and Lin the final (almost) product. Without their patience and understanding along with a...

Although many would disagree, these are in my opinion average quality. "BUT" they are the best reproductions currently available. The inner portion where your fingers go have too sharp of edges and they do not hold up nearly as well as the originals do. We also have used in most colors available. Thank You Don and WCCC, Copy Cat's almost done! Yesterday was such a nice day I took Copy Cat out to Show Don and Lin the final (almost) product. Without their patience and understanding along with a...

Although many would disagree, these are in my opinion average quality. "BUT" they are the best reproductions currently available. The inner portion where your fingers go have too sharp of edges and they do not hold up nearly as well as the originals do. We also have used in most colors available. Thank You Don and WCCC, Copy Cat's almost done! Yesterday was such a nice day I took Copy Cat out to Show Don and Lin the final (almost) product. Without their patience and understanding along with a...

Although many would disagree, these are in my opinion average quality. "BUT" they are the best reproductions currently available. The inner portion where your fingers go have too sharp of edges and they do not hold up nearly as well as the originals do. We also have used in most colors available. Thank You Don and WCCC, Copy Cat's almost done! Yesterday was such a nice day I took Copy Cat out to Show Don and Lin the final (almost) product. Without their patience and understanding along with a...

Although many would disagree, these are in my opinion average quality. "BUT" they are the best reproductions currently available. The inner portion where your fingers go have too sharp of edges and they do not hold up nearly as well as the originals do. We also have used in most colors available. Thank You Don and WCCC, Copy Cat's almost done! Yesterday was such a nice day I took Copy Cat out to Show Don and Lin the final (almost) product. Without their patience and understanding along with a...

Although many would disagree, these are in my opinion average quality. "BUT" they are the best reproductions currently available. The inner portion where your fingers go have too sharp of edges and they do not hold up nearly as well as the originals do. We also have used in most colors available. Thank You Don and WCCC, Copy Cat's almost done! Yesterday was such a nice day I took Copy Cat out to Show Don and Lin the final (almost) product. Without their patience and understanding along with a...