1969 Mercury Cougar

Used bracket or mounting tab that often gets lost when servicing the air conditioning plenum. Attaches to the box with two screws and has stud that goes through the engine firewall for mounting the A/C box assembly under the dash. Basically the same part as found on 1967-68 brackets, but this one has a slightly longer stud. Replaces Ford part number C9ZZ-18A456-A.

Billet aluminum batter hold down bracket for all 1967-70 Mercury Cougar and Ford Mustangs. Maximum battery width 6-3/4 inches. We also have stainless steel hold down bolts available.

Carburetor dash pot bracket, this is the smaller bracket and was likely used during the 1968 Model year. Unknown when exactly. Fits all Autolite 2100 and 4300 carburetors if needed 1968-70 Mercury Cougar and Ford and Mustang. Some of these have a trace of Gold color on them like other carburetor parts. Small hole for attaching to left front of the carburetors, before anyone asks, we do not have the fasteners for these. Larger hole is threaded for factory installed dashpot which is 5/16-24....

Reproduction bracket assembly for mounting the J hood and inflator cannister. Trunk plate or bracket for mounting the "J" bolt for the spare tire also included is the saddle bracket for mounting the tire inflator cannister. Mounts on the top of the trunk floor surface. 1969-70 Mercury Cougar convertibles and hard tops with space saver spare tires. Additionally, 1971-73 Mercury Cougar hard tops. *Trivia - According to the Concours Mustang Forum, this bracket wasn't installed or available...

Used bracket assembly for mounting the J hood and inflator cannister. Trunk plate or bracket for mounting the "J" bolt for the spare tire also included is the saddle bracket for mounting the tire inflator cannister. Mounts on the top of the trunk floor surface. 1969-70 Mercury Cougar convertibles and hard tops with space saver spare tires. Additionally, 1971-73 Mercury Cougar hard tops. We cut these out of the trunk floors, so there will be some metal preparation for the customer. Rare...

Driver side convertible frame assembly mounting and pivot bracket for all 1969-70 Mercury Cougar and Ford Mustang. Does not include the hydraulic cylinder bracket, cylinder mounting bracket sold separately. Bushings, bolts, and specialty fasteners not included. Passenger side bracket with attached convertible arm only. Mounts behind the quarter interior panel. Ford part number C9ZZ-7653119-A.

Passenger side convertible frame assembly mounting and pivot bracket for all 1969-70 Mercury Cougar and Ford Mustang. Does not include the hydraulic cylinder bracket, cylinder mounting bracket sold separately. Bushings, bolts, and specialty fasteners not included. Passenger side bracket with attached convertible arm only. Mounts behind the quarter interior panel. Ford part number C9ZZ-7653118-A.

Detachable mounting plate for installing the driver side convertible ram cylinder, to the convertible top frame assembly behind the quarter interior panel. Right and left are the different, fits all 1969-70 Mercury Cougar and 1965-70 Ford Mustang convertibles. Ford part number C5ZZ-76531A19-A.

Detachable mounting plate for installing the passenger side convertible ram cylinder, to the convertible top frame assembly behind the quarter interior panel. Right and left are the different, fits all 1969-70 Mercury Cougar and 1965-70 Ford Mustang convertibles. Ford part number C5ZZ-76531A18-A.

These courtesy light brackets are located on the very outer right and left under the dash. Sold individually, two required per car. Same bracket used on both sides. Replaces Ford part number C9ZZB-13763-A.Fits:1969 Mercury Cougar1969 Ford Mustang

Used bracket for installing the defrost nozzles assembly to the dash on all 1969-70 Mercury Cougar or Ford Mustang with factory air conditioning. Bracket only, no attaching hardware.

Used bracket for holding either the emergency flasher or turn signal flasher on many Fords dating from 1963. We find these mainly in 1969-70 Mercury Cougar and Ford Mustangs. This holder attaches to one of two different relay mounting brackets. Couple of different designs were also used. Additionally there is also a different style of flasher mounting bracket. See our related items.Replaces Ford part number C3AB-13351.