All Available Parts - 1969 Mercury Cougar

Used simulated wire spoke hubcap / wheel cover that is in average condition with minor curb scrapes. Most Cougar s were equipped with the black center medallion from the factory but when sold as an over the counter accessory often the red center caps were sold to Cougar owners. If you have black centers and would like to exchange them for our red centers we would be happy to oblige! Ford part # C7WY-1130-C.*NOTE* You will often see this same cap with the Mercury head center and a red...

Used sports special turbine / Dan Gurney Special hubcap / wheel cover. Grade B, driver quality, will have curb scratches.Ford part # C7WY-1130-F.*NOTE* You can often find a hubcap like this with the Mercury Head center. This is not correct for the Cougar, but rather the Montego, the foil decal in the center can easily be removed.Fits:1967 Mercury Cougar1968 Mercury Cougar1969 Mercury Cougar ...

Used Grade B 3 1/2" XR7 center cap emblem was used on the Mercury Cougar XR7 hubcap / wheel cover. 

Finally! A close reproduction of the original Chrome acorn style lug nuts that fit the styled steel wheels. These premium lugs nuts stand just a little taller than the originals, hard to detect unless you have them side by side with NOS.They have the correct matte finish and pointed top. If you are not building a show car then you will want to buy the brighter, generic version that you can find here. Fits the following models with styled steel wheels:1967 Mercury Cougar1968 Mercury Cougar1969...

Standard stamped steel wheel lug nuts in good used condition. 1/2"-20. Need to replace missing, cross threaded, or otherwise damaged lug nuts? Do you have after-market chrome wheels with the flat washers and closed round head lugs? Fits the following models with stamped steel wheels:1967 Mercury Cougar1968 Mercury Cougar1969 Mercury Cougar1970 Mercury Cougar1971 Mercury Cougar1972 Mercury Cougar1973 Mercury Cougar Should have a set of 5 in the trunk for use with your stock steel spare...

Chrome acorn lug nut for most any Ford steel wheel including styled steel, Magnum 500,  new or reproductions.Replaces Ford Part #: C9ZZ-1012-B.

This is a standard reproduction lug nut that Fits the styled steel wheels and is the same as the original. 1/2"-20. Need to replace missing, cross threaded, or otherwise damaged lug nuts? Do you have after-market chrome wheels with the flat washers and closed round head lugs? Fits the following models with stamped steel wheels: 1967 Mercury Cougar 1968 Mercury Cougar 1969 Mercury Cougar 1970 Mercury Cougar 1971 Mercury Cougar 1972 Mercury Cougar 1973 Mercury...

Short rubber valve stem and cap for Ford wheels or any steel wheel with a 0.453" hole. Snap in style, sticks up 1-1/4 from wheel surface. These will work with our aftermarket Ford wheels without trim rings. These have the Dill 627 caps. Same as the 1960's cars.

Short rubber valve stem and cap for Ford wheels or any steel wheel with a 0.453" hole. Snap in style, sticks up 2 inches from wheel surface. These will work with all of our aftermarket Ford wheels especially with trim rings. These have the Dill 627 caps. Same as the 1960's cars.

Short steel chromed valve stem for Ford wheels or any steel wheel with a 0.453" hole. Clamp in or bolt in style, sticks up 3/4 from wheel surface, 200psi maximum pressure. These will work with our aftermarket Ford wheels without trim rings. These are not compatible with our aluminum wheels.Premium grade, marked for "High Temperature".

New wheel stud replacement for all Mercury Cougars equipped with front drum brakes. Pretty much fits most other front drum brakes on all mid sized Ford and Mercury cars. Front drum brakes only, serrated 2" stud with correct 1/2 x 20 threads. These are slightly longer in length than the stock ones, this will allow the alloy wheels to fit the Classic Cougars.Replaces Ford part # C30Z-1107-A.*NOTE* You should use a press to remove and/or install the new studs.

Used lug nut for your 1967 - 1970 Cougar

5-Lug Kit includes 20 chrome tapered 13/16" lug nuts and 4 chrome valve stems for installation of the new Legendary aluminum wheels. These really only fit the Magstar style wheels; we recommend the 3/4" lug nuts for all the other Legendary wheels for clearance reasons. Conical Head: 13/16" Hex Thread Size: 1/2" Bolt Pattern Also available individually.Check out our video on Legendary Wheels below: ...

Chrome tapered acorn lug nut for use with the new Legendary wheels. This 13/16" nut really only fits the Magstar style - the others have tighter clearances and you'll want to use the 3/4" nuts made for these wheels. Sold individually here, or in a complete set with valve stems. Replaces Ford Part #: C9ZZ-1012-B.Check out our video on Legendary Wheels below: ...

5-Lug Kit includes 20 chrome lug nuts and 4 chrome valve stems for installation of the new aluminum Legendary Series wheels. Tapered for correct fit. This 3/4" size is what we recommend you use with the Legendary wheels, since the clearances are too tight for 13/16" nuts. Conical Head: 3/4" Hex Thread Size: 1/2" Bolt Pattern Also available individually.Check out our video on Legendary Wheels below: ...

Correct 3/4" tapered chrome acorn lug nut for the new Legendary Wheels. These are what we recommend you use with these wheels, since the clearances are too tight for regular 13/16" lug nuts. Sold individually here, or as a complete set with valve stems.Check out our video on Legendary Wheels below: ...

A close economy reproduction of the original Chrome acorn style lug nuts that fit the styled steel wheels. These stand just a little shorter than our other, more accurate reproductions.They don't have the correct matte finish, have a smaller head section and longer edges, but do still have the pointed top. If you are not building a show car then you may want to go with this generic version. Fits the following models with styled steel wheels:1967 Mercury Cougar1968 Mercury Cougar1969 Mercury...

5-Lug Kit includes 20 chrome tapered 13/16" lug nuts and 4 chrome valve stems. Specifically for installation of the new Legendary GT7 and 1966 Shelby wheels. Thread Size: 1/2" Bolt Pattern Check out our video on Legendary Wheels below: ...

Reproduction lug nut for the Legendary GT7 Series wheel. Sold Individually. You can find the complete lug nut installation kit here.Check out our video on Legendary Wheels below: ...

Reproduction nylon lug nut protectors. These are sold in pairs, and come with 3/4" and 13/16" sizes. Simply slide one of these sleeves into your socket and keep the chrome on your lug nuts in perfect condition!These protectors are simple plastic and are prone to breaking. Can be used on a variety of other vehicles with the same lug nut size. For the 3/4" lugs, use the sleeve with a 7/8" socket. For the 13/16" lugs, use the sleeve with a 15/16" socket. ...

These open lug nuts are commonly used on drag strip or race cars . They will accommodate the aftermarket extended studs which are prevalent in all forms of racing. Plated bright silver zinc. Extended Thread design will work on any Legendary Wheel. 3/4 hex allows plenty of room for sockets. 1/2 x 20 threads. Check out our video on Legendary Wheels below: ...

Dill 627 valve stem caps. Set of 5 caps. Same as the 1960's cars.

Dill 627 valve stem cap. Same as the 1960's cars. See related items, also sold as a set of 5 caps.

New extra long wheel stud replacement for all Mercury Cougars equipped with front drum brakes. Pretty much fits most other front drum brakes on all mid sized Ford and Mercury cars. Front drum brakes only, serrated 2-1/4" stud with correct 1/2 x 20 threads.  These are 1/4" longer in length than the stock studs, this will allow the alloy wheels, wheel spacers and aftermarket disc brakes.Replaces Ford part # C30Z-1107-A.*NOTE* You should use a press to remove and/or install the new...

Reproduction Legendary GT9 series aluminum wheel in the gloss black finish. It was inspired by the factory Shelby rim used on the 1969-70 GT350 and GT500’s. It was and still is a great looking combination of the original Torque Thrust and the iconic Magnum 500. All versions feature a gloss clear coat for protection. 4.25" Back spacing5 x 4.5" Bolt pattern These wheels come with free chromed plastic center caps. The caps have a red Legendary logo but we can include at no cost, a set of black...

Reproduction Legendary GT9 series aluminum wheel in the charcoal finish. It was inspired by the factory Shelby rim used on the 1969-70 GT350 and GT500’s. It was and still is a great looking combination of the original Torque Thrust and the iconic Magnum 500. All versions feature a gloss clear coat for protection. 4.25" Back spacing5 x 4.5" Bolt pattern These wheels come with free chromed plastic center caps. The caps have a red Legendary logo but we can include at no cost, a set of black and...

Reproduction Legendary GT9 series aluminum wheel in the natural finish. It was inspired by the factory Shelby rim used on the 1969-70 GT350 and GT500’s. It was and still is a great looking combination of the original Torque Thrust and the iconic Magnum 500. All versions feature a gloss clear coat for protection. 4.25" Back spacing5 x 4.5" Bolt pattern These wheels come with free chromed plastic center caps. The caps have a red Legendary logo but we can include at no cost, a set of black and...

Reproduction Legendary GT9 series aluminum wheel in the gloss black finish. It was inspired by the factory Shelby rim used on the 1969-70 GT350 and GT500’s. It was and still is a great looking combination of the original Torque Thrust and the iconic Magnum 500. All versions feature a gloss clear coat for protection. 4.25" Back spacing5 x 4.5" Bolt pattern These wheels come with free chromed plastic center caps. The caps have a red Legendary logo but we can include at no cost, a set of black...

Reproduction Legendary GT9 series aluminum wheel in the gloss black finish. It was inspired by the factory Shelby rim used on the 1969-70 GT350 and GT500’s. It was and still is a great looking combination of the original Torque Thrust and the iconic Magnum 500. All versions feature a gloss clear coat for protection. 4.25" Back spacing5 x 4.5" Bolt pattern These wheels come with free chromed plastic center caps. The caps have a red Legendary logo but we can include at no cost, a set of black...

Reproduction Legendary GT9 series aluminum wheel in the charcoal finish. It was inspired by the factory Shelby rim used on the 1969-70 GT350 and GT500’s. It was and still is a great looking combination of the original Torque Thrust and the iconic Magnum 500. All versions feature a gloss clear coat for protection. 4.25" Back spacing5 x 4.5" Bolt pattern These wheels come with free chromed plastic center caps. The caps have a red Legendary logo but we can include at no cost, a set of black and...

Reproduction Legendary GT9 series aluminum wheel in the charcoal finish. It was inspired by the factory Shelby rim used on the 1969-70 GT350 and GT500’s. It was and still is a great looking combination of the original Torque Thrust and the iconic Magnum 500. All versions feature a gloss clear coat for protection. 4.25" Back spacing5 x 4.5" Bolt pattern These wheels come with free chromed plastic center caps. The caps have a red Legendary logo but we can include at no cost, a set of black and...

Reproduction Legendary GT9 series aluminum wheel in the natural finish. It was inspired by the factory Shelby rim used on the 1969-70 GT350 and GT500’s. It was and still is a great looking combination of the original Torque Thrust and the iconic Magnum 500. All versions feature a gloss clear coat for protection. 4.25" Back spacing5 x 4.5" Bolt pattern These wheels come with free chromed plastic center caps. The caps have a red Legendary logo but we can include at no cost, a set of black and...

Reproduction Legendary GT9 series aluminum wheel in the natural finish. It was inspired by the factory Shelby rim used on the 1969-70 GT350 and GT500’s. It was and still is a great looking combination of the original Torque Thrust and the iconic Magnum 500. All versions feature a gloss clear coat for protection. 4.25" Back spacing5 x 4.5" Bolt pattern These wheels come with free chromed plastic center caps. The caps have a red Legendary logo but we can include at no cost, a set of black and...

Used grade "A" simulated wire spoke hubcap / wheel cover that is in excellent condition with no curb scrapes. This listing is for someone who has removed their center from their current damaged cap and wants to save money by purchasing a cap with no center. The same cap was used on Most all FoMoCo products including but not limited to the Falcon, Mustang, Fairlane, Comet, Galaxie, Montego and LTD, only the center logo changed one car to the next. Ford part # C7WY-1130-C. *NOTE* You will often...

Used wire spoke hubcap / wheel cover for the 69 - 73 Cougar. These units are above average with no scratches where they have rubbed the curb, almost pitting in the center and faint, if any fading in the logo.Ford part # D0WY-1130-DFits:1969 Mercury Cougar1970 Mercury Cougar1971 Mercury Cougar1972 Mercury Cougar1973 Mercury Cougar ...

Used simulated wire spoke hubcap / wheel cover that is in average condition with minor curb scrapes. This listing is for someone who has removed their center from their current damaged cap and wants to save money by purchasing a cap with no center. The same cap was used on most all FoMoCo products including, but not limited to the Falcon, Mustang, Failane, Comet, Galaxie, Montego and LTD. Only the center logo changed from one car to the next. Ford part # C7WY-1130-C. ...

Used simulated wire spoke hubcap / wheel cover that is in above average condition with no curb scrapes. This listing is for someone who has removed their center from their current damaged cap and wants to save money by purchasing a cap with no center. The same cap was used on most all FoMoCo products including, but not limited to the Falcon, Mustang, Fairlane, Comet, Galaxie, Montego and LTD. Only the center logo changed from one car to the next. Ford part # C7WY-1130-C. ...

Reproduction dog dish style hubcaps / wheel covers for the Mercury Cougar as well as other Mercury and Ford products. There are no less than three versions of this reproduction unit on the market. This one, in my opinion, is the best option. The hue is not as brilliant as the original, but a very nice cap for the fit and finish that it offers. We have trim rings available too! Check out our video on Legendary Wheels below: NOTE: These are for use on the Legendary Series Eliminator wheels Fits:...

Used standard hubcap / wheel cover for the Mercury Cougar Standard. These units are getting harder and harder to find in good condition because the protrude enough that they are very prone to curb damage. Grade A will show no discoloration in the blue plexi center, the paint may very minimal to no fading and will have no scratches or dings.Ford part # C9WY-1130-C.Fits:1969 Mercury Cougar Standard1970 Mercury Cougar Standard ...

Brand new cap, sometimes the boxes are missing due to age.Ford part # C9WY-1130-C.Fits:1969 Mercury Cougar Standard1970 Mercury Cougar Standard

Used grade A "dog dish" style hubcap that will show minimal or no paint loss / fading and no dings. Most early Cougars used the full hubcap / wheel cover, so this one is rarely found on a Cougar. We have seen these used on wheels painted the body color on basic Cougars as well as black painted wheels.Ford part # C8MY-1130-A

Excellent condition NOS "dog dish" style hubcap. Most early Cougars used the full hubcap / wheel cover, so this one is rarely found on a Cougar. We have seen these used on wheels painted the body color on basic Cougars as well as black painted wheels. Ford part # C8MY-1130-A

This spring does NOT have correct spring finish or tension, but will work fine if you want to save a few $$$. Above is a comparison to this reproduction which is carried by other retailers, compared to our spring which is very close to the correct finish, length, and tension. Replaces Ford Part # : C8ZZ-17119-A ...

Very close to correct spring finish (dark color) and tension. Above is a comparison to the other reproduction, which does not have the correct finish, is not the correct length, and does not have the correct tension. Replaces Ford Part # : C8ZZ-17119-A *Note* Must be used with the correct mounting bracket. See below. ...

Spare tire, with styled steel wheel hold down disc. Fits all 1968-70 Mercury Cougar and Ford Mustang. Original Ford part number C8MY-1424-A. About 3 inches in diameter, this is the specified trunk hold down plate for the use with the factory mag wheels.

Concourse Correct FLAPPER DOOR ASSEMBLY for vehicles equipped with ram-air. Includes: door, pivot rod, and 2 retaining clips Fits 1969 390GT and 1970 Boss 302, 351W, 351C. Replaces Ford Part #: C9ZZ-9610-A

This was the inner air cleaner lid used on the Mercury Cougars equipped with a 428 Ram Air Cleaner or 429 Cobra Jet Ram Air Cleaner assembly. Although you will often find chrome under the blue engine paint on these lids they are in fact supposed to be painted from the factory. This lid is 14-1/8 inches in diameter. The reason you will often see chrome underneath the paint is that this is the same lid used on the 1967 427 GTE, 289 HiPo equipped early Mustangs and 390 GT / GTA Fairlanes and...

This lid is found on many years and cars 1968 - 1971. The diameter of the lid is just over 17 3/4", fits on 17.84" air cleaner bases. Application Mercury Cougar Ford Mustang 302 and 351 engines without ram air. Ford / Mercury have had various part numbers listed for this basic lid over the years. The primary difference was the original lids included an engine size sticker. That is why there are so many listings, the basic part number is 9661. This lid was chromed in several applications,...

C8AF-9600-G Standard air cleaner base for all 351 engines, H code 351-2V and M code 351-4V. About 17.84" inches in diameter. Identified with the square nuts welded on the inside for mounting the air cleaner snorkel. Otherwise the same as C8AF-9600-C. Ford part number C8AZ-9600-D.

A nice reproduction of the standard air cleaner wing nut. This version was used on most Ford products through the 1980's.

Round ring shaped gasket that goes on top of the carburetor. Protects and seals the carburetor to the air cleaner.

This rechromed lid is found on many years and cars 1968 - 1971. The diameter of the lid is just over 17 3/4", fits on 17.84" air cleaner bases. Application Mercury Cougar Ford Mustang 302 and 351 engines without ram air. Ford / Mercury have had various part numbers listed for this basic lid over the years. The primary difference was the original lids included an engine size sticker. That is why there are so many listings, the basic part number is 9661. This lid was chromed in several...

Good used rubber ram air seal for any 1968-70 Mercury Cougar or 1968 Ford Mustang. May have some warpage issues. 

This Filters Last 40% Longer & Holds 53% More Dirt Than Most other Filters. * This filter fits primarily Big Block cars, but a couple of other combinations, so grab a tape measure and double check the height of the one you need to replace, as that will tell you which one you need. Air Filter Height (Inches) : 2.193" Air Filter Height (mm) : 55.7 mm  Air Filter Bottom I.D. (Inches) : 11.32" Air Filter Bottom I.D. (mm) : 287.53 mm Air Filter...

This Filters Last 40% Longer & Holds 53% More Dirt Than Most other Filters. Please note that the Ford Service Replacement specs for this filter (Service Replacement # D7AF9601AA) are; Type: 67; Inside: 13.000; Outside: 11.200; Height: 2.795. All reproductions that we have found follow these specs, making the filter 1/8" taller than the original filters. These filters will function properly, but the lid will not seat properly. ACTUAL FILTER SPECS: Air Filter Height (Inches) : 2.822...

Correct dimensions, good fit. Will show minor cracks in rubber but will not affect performance and cannot be seen when installed. Replacement air cleaner for the 1967 - 1973 Mercury Cougar Walking Cat Oval Air Cleaner, as well as other Ford oval air cleaners.

These filters feature the correct color of filter paper and an red/orange molded face. In addition, they have the correct "round hole" design on the outer shell. Fits Mustang 1965-67 K code HiPo 289 and 1968 Mercury Cougar GT-E W code 427-4V engines, that were originally equipped with the chrome high performance air filter assemblies. Please note: this filter will NOT fit a standard Ford air cleaner Replaces Ford Part #: B7SZ-9601-A. ...

Replacement air filter for the 1967 - 1973 Mercury Cougar 14" 'Cal Custom' Aluminum Finned Air Cleaner Assembly.

Steel spacer between cylinder head and pump. Inside diameter 3/8", length approximately 1-13/16".

C5AZ-10A370-C Alternator mounting spacer, goes between the cylinder head and alternator housing. Fits 1968-70 390-2V, 390-4V, and 428CJ engines. Smog OK. There is no casting number but one is listed C5AE-10A370-C. Inside diameter 7/16". We measure them out at 1-5/8 inches long, supposed to be pink anodized or tinted.

Application - 1968 - 390-4V and 427-4V, and all 1968 - 1970 428 Cobra Jet engines. This is also referred to as the low mount alternator mounting bracket. It has the Ford stamped casting number of C8AE-10156-A. Ford engineering number is C8AZ-10156-A.

C8AE-9B452-B Thermactor smog pump belt tensioning adjustment bracket. Application is for all 1968 - 1970 FE engines with factory installed thermactor smog systems.

Molded "S" shaped vacuum hose. Feed hose from the smog pump to the Carter anti-backfire distribution valve.

Thermactor smog anti-backfire valve canister mounting bracket. For all 1968 390GT engines, GT-E 427-4V engines, and 1968-70 428 Cobra Jet engines. Ford part # C8AE-9C486-A. *RESTORATION TIP* This bracket was painted Ford Engine blue from the factory.

Reproduction hardware kit for installing the smog pump on cars with 390 / 427 / 428CJ engines from 1968-70. Including Cougar, Mustang, Torino, Ranchero, Cyclone, etc. Includes spacer, pivot bolt and washer, adjusting bracket bolts.

Nice American made reproduction bracket. Application - 1968 - 390-4V and 427-4V, and all 1968 - 1970 428 Cobra Jet engines, all with Thermactor smog pumps. This is also referred to as the low mount alternator mounting bracket. It has the Ford stamped casting number of C8AE-10156-A. Ford engineering number is C8AZ-10156-A.

Reproduction thermactor smog anti-backfire valve canister mounting bracket. For all 1968 390GT engines, GT-E 427-4V engines, and 1968-70 428 Cobra Jet engines. Painted Ford engine blue a shown. Nice reproduction, made in the USAFord part # C8AE-9C486-A.

Reproduction Carter 4491S smog canister valve with any supplied stamped date. Special order item, allow several weeks for delivery, and it will ship separately. Nice and detailed with correct stamping on the cover with your supplied date. Fits 289 / 302 / 390-4V / 427-4V/ 428CJ in 1968. Fits 428 Cobra Jet and 428 Super Cobra Jet for 1969-70. All 1968 Ford cars and light duty pickups received thermactor smog if they had a manual transmission and / or Holley 4V carburetor. Thermactor smog pumps...

Reproduction thermactor smog pump adjusting bracket for all 1968 Mercury Cougar and 1968 Ford Mustang with S code 390-4V engines. Additionally this bracket was also used on 1968-70 Mercury Cougar and Ford Mustang with 428 Cobra Jet engines. Quality made product. Ford number C8AE-9B452-B.

Three piece Thermactor Smog hose set; moulded, striped, and stamped like original factory installed hoses. The 1968 ink stamped was likely used partially into 1969. We also list hoses with the C9... stamps.Fits: 1968 Ford and Mercury S code 390-4V engines sold in the US.1968 Ford and Mercury W code 427-4V engines sold in the US1968 / 1969 428 Cobra Jet engines. 1968 / 1969 428 Super Cobra Jet engines. ...

Thermactor smog tube installation ferrules. Set of 8 nuts and barrel shaped ferrules.Fits: 1968 Ford and Mercury S code 390-4V engines sold in the US.1968 Ford and Mercury W code 427-4V engines sold in the US. 1968 / 1969 / 1970 428 Cobra Jet engines.1968 / 1969 / 1970 428 Super Cobra Jet engines. ...

Thermactor smog hose installation clamps. Fits all Ford and Mercury 1968 S code 390-4V or W code 427-4V engines sold in the US. Additionally fits 1968-70 428 Cobra Jet and Super Cobra Jet engines. Set of clamps, several bolts and spacer as shown. Include bolts for pump pulley, top bolt on pump for adjusting bracket, and pivot bolt and spacer for pump.

Set of nuts and Ferrules for thermactor smog tubes on any 1967 S code 390, 1968 390GT, 1968 GT-E 427-4V, or 1968-70 428 Cobra Jet engines. Mercury Cougar and Ford Mustang, Torino, Cyclone, Ranchero, etc. These will work with original or reproduction smog tubes. Fits most FE engine applications that used the air pump smog system in 1968 with manual transmission. We also have the smog tubes and other hardware.

Set of thermactor smog tubes on any 1968 390GT, 1968 GT-E 427-4V, or 1968-70 428 Cobra Jet engines. Mercury Cougar and Ford Mustang, Torino, Cyclone, Ranchero, etc. These will work with original 390 or 428CJ cylinder heads drilled for air injection smog system from factory. Fits most FE engine applications that used the air pump smog system in 1968 with manual transmission. We also have the ferrules / nuts and other hardware.

Application is 1967 - 1968 289/302 and 1969 Boss 302 Eliminator alternator adjusting with factory air injection emissions. Casting number C6OE-10145-A, Ford part number C6OZ-10145-A.

Application 1968 - 289-2V, 302-2V, 302-4V, all with manual transmissions and without air conditioning. Also 1968 390-4V and 1968 - 1970 428CJ, all without air conditioning. Pulley diameter 4.75" inches. Ford part number is C8AZ-9B447-B and the engineering number as seen on the front of the pulley is C8AE-9C480-A.

Common air pump for all 1968 - 1970 thermactor emissions systems. 1968 289-2V, 302-2V, and 302-4V all with manual transmissions, and 1968 390-4V, 427-4V all domestic US Cougars. Additionally all 1968 - 1970 428 Cobra Jets, and 1969 - 1970 Boss 302 Eliminators. Identified by the use of 3 attaching bolts for the drive pulley, a white colored cooling fan, and a round pressure relief valve on the side of the pump. Later pumps do not have this pressure relief valve. Current date: 7J231   ...

Common air pump for all 1968 - 1970 thermactor emissions systems. 1968 289-2V, 302-2V, and 302-4V all with manual transmissions, and 1968 390-4V, 427-4V all domestic US Cougars. Additionally all 1968 - 1970 428 Cobra Jets, and 1969 - 1970 Boss 302 Eliminators. Identified by the use of 3 attaching bolts for the drive pulley, a white colored cooling fan, and a round pressure relief valve on the side of the pump. Later pumps do not have this pressure relief valve. Good used thermactor smog air...

Screws onto the cylinder head smog tubes. Sold individually, two needed per application. Ford part number C8AZ-9A487-A.New old stock Ford.

Wide range of applications, which also include: 289-2V (C code engine), 302-2V (F code engine), 302-4V (J code engine) - Only 1968, and only with manual transmissions either 3 speed or 4 speed. 1968 390-4V, with any transmission. 1968 427-4V GT-E, and 1968 - 1970 428 Cobra Jet and Super Cobra Jet. Typical core valve, will not function. Basically selling a non functional smog part with a desirable date of 1/2/1968. Could also have a casting number of C8OE-9B289-B, the covers on the valves do...

C8TE-B-SR Correct service replacement 4490-S Carter anti backfire valve, but without the outer cover having the concours correct stampings. These units are used, not tested and one should assume they are non-functional.

Wide range of applications, which also include: 289-2V (C code engine), 302-2V (F code engine), 302-4V (J code engine) - Only 1968, and only with manual transmissions either 3 speed or 4 speed. 1968 390-4V, with any transmission. 1968 427-4V GT-E, and 1968 - 1970 428 Cobra Jet and Super Cobra Jet. Typical core valve, will not function. Basically selling a non functional smog part with a desirable date of 9/5/1967. This valve has the date stamped so that it is visible when looking at the...

Wide range of applications, which also include: 289-2V (C code engine), 302-2V (F code engine), 302-4V (J code engine) - Only 1968, and only with manual transmissions either 3 speed or 4 speed. 1968 390-4V, with any transmission. 1968 427-4V GT-E, and 1968 - 1970 428 Cobra Jet and Super Cobra Jet. Typical core valve, will not function. Basically selling a non functional smog part with a desirable date of 3/19/1968. Could also have a casting number of C8OE-9B289-B, the covers on the valves do...

Wide range of applications, which also include: 289-2V (C code engine), 302-2V (F code engine), 302-4V (J code engine) - Only 1968, and only with manual transmissions either 3 speed or 4 speed. 1968 390-4V, with any transmission. 1968 427-4V GT-E, and 1968 - 1970 428 Cobra Jet and Super Cobra Jet. Typical core valve, will not function. Basically selling a non functional smog part with a desirable date of 8/16/1967. Could also have a casting number of C8OE-9B289-B, the covers on the valves do...

Wide range of applications, which also include: 289-2V (C code engine), 302-2V (F code engine), 302-4V (J code engine) - Only 1968, and only with manual transmissions either 3 speed or 4 speed. 1968 390-4V, with any transmission. 1968 427-4V GT-E, and 1968 - 1970 428 Cobra Jet and Super Cobra Jet. Typical core valve, will not function. Basically selling a non functional smog part with a desirable date of 4/23/1968. This valve has the date stamped so that it is visible when looking at the...

Wide range of applications, which also include: 289-2V (C code engine), 302-2V (F code engine), 302-4V (J code engine) - Only 1968, and only with manual transmissions either 3 speed or 4 speed. 1968 390-4V, with any transmission. 1968 427-4V GT-E, and 1968 - 1970 428 Cobra Jet and Super Cobra Jet. Typical core valve, will not function. Basically selling a non functional smog part with a desirable date of 2/21/1968. Could also have a casting number of C8OE-9B289-B, the covers on the valves do...

Wide range of applications, which also include: 289-2V (C code engine), 302-2V (F code engine), 302-4V (J code engine) - Only 1968, and only with manual transmissions either 3 speed or 4 speed. 1968 390-4V, with any transmission. 1968 427-4V GT-E, and 1968 - 1970 428 Cobra Jet and Super Cobra Jet. Typical core valve, will not function. Basically selling a non functional smog part with a desirable date of 10/12/1967. Could also have a casting number of C8OE-9B289-B, the covers on the valves do...

This premium antenna and base is a very close reproduction. Note that it comes with a Mustang base gasket which will work on your Cougar, but will tilt the angle of the mast slightly. Your antenna gasket options are to buy a used one from us, reuse your gasket, modify the Mustang gasket, or just live with an antenna that is tilted and looks wacky.Click on images to enlarge. The gasket on the right is what comes with the kit.  It is a Mustang gasket and designed to fit the contour of a...

Reproduction antenna base gasket.Replaces Ford part #  C9WA-18298-B.

This is the correct, original cover for your 1969-70 Mercury Cougar and 1969-70 Ford Mustang antenna. The Ford MPC calls this part a cap, it is the stainless steel rectangular piece of trim that goes on top of your factory antenna base. These are angled, so watch the orientation when installing.  Most of these had a paper tag with part number and "FRONT" installed at the factory. These snap into place on the OEM factory installed antenna base. Used gasket also available.Replaces Ford part...

Used in conjunction with the front bracket, bolts onto stud protruding from the rear of your radio, rather hard to find once the original radio has been removed. One exception; 1972-73 Mercury Cougar and Ford Mustang AM/FM radios used a different bracket marked D2ZA-18888-AB. *Customer Feedback*"These guys have got to be the most professional I've dealt with in the 4 years I've been restoring my Mustang and Cougar. I have had nothing but pleasant conversations even though I tend to be long...

Mercury Cougar and Ford Mustang factory AM radio with "Philco" spelled out on the face plate. This radio may or may not work, probably will have a cut plug. Good for parts or to fill a hole. Many people prefer the original look and to hide their modern sound system. Knobs sold separately. Ford part # C9ZA-18806-E. Are you going to install this unit yourself? The first issue of Legendary Cougar Magazine has a great how to article that will help you in your journey to musical bliss. You...

Currently out of black. Our used plastic radio trim piece has been inspected for cracks and scrapes and has been found to be in good used condition. These original parts are better quality than the reproductions, and unlike the reproductions, you can buy our used trim parts individually. Please select a color and we will attempt to accommodate. Plan on these used plastic parts needing to be painted.

Black is currently out of stock. We have green. This good used plastic radio trim part has been inspected for cracks and scrapes and has been found to be in good used condition. These original parts are better quality than the repros and unlike the reproductions you can buy them individually. Please select a color and we will attempt to accommodate. Plan on these used plastic parts needing to be painted.

This is a decent reproduction of the radio bracket for the 69 or 70. Take a look at the smaller image to see them side by side. The repro is slightly taller and has extra holes in it so it fits other applications. We recommend sticking with good originals.  Why deviate from 100% correct if you don't need to.

Cougars never came with a straight grain decal on the radio bezel, but this Mustang bezel fits in with the straight grain accents found on the 69-70 standard Cougar interior. Replaces Ford part # C9ZZ-6504774-F. Check out this video

Here's another quality reproduction with the correct camera case finish used on all 1969-70 Mustangs and Cougars except Xr7. Replaces Ford part # C9ZZ-6504774-B.

If you want great sound at an affordable price then this is the radio for you! Now with 200 watts and auxiliary input for iPod, MP3, satellite radio, etc. If you have a 1967 - 1968 Cougar with a center console, the knobs included will work. �?�AM-FM Stereo �?� 200 watts (4x50) �?� Rear Auxiliary Input �?� Electronic Tuning and Volume Control �?� Pre-set Scan �?� Digital Clock �?� Best Station Memory �?� 30 Pre-sets (12AM-18FM) �?� 4 Channel RCA Pre-outs �?� 4 way Fader �?� Separate Bass and...

FEATURES : KHE 300-USB Features: * Wireless Bluetooth; * Mini SD Card Reader; * USB Flash Drive; * 6 AM/6 FM Preset; * Manual Up/Down Tuning; * Seek Auto Tune; * Auto Stereo/Mono; * Preset Scan and Auto Store; * Front/Rear Fader Control; * On/Off Volume Control; * Separate Bass/Treble Control; * Left/Right Balance Control; * Auto Antenna Power Lead; * LCD Display with Blue Back Lighting; * Aux Input Rear; * Frequency Selector. Size: N/A * Output: 50 Watt x 4 Channel * System Power: 200 Watts...

Secretaudio SST is a hidden audio system that offers great flexibility for mounting in any type of vehicle. The main receiver/amplifier unit is usually hidden under the seat, or behind the dash. A 10ft cord from the Tuner/Amp plugs into a LCD display. The system can be operated from up to 40 feet away with the included RF (radio frequency remote.) Included with the system is a flush mount bezel for console or dash mounting. The small dimensions of the flush mount system allow you to install...