All Available Parts - 1969 Mercury Cougar

This strip has a series of seven retaining clips that hold the headlining panel to the roof panels as seen on page 14 of the sun roof manual.

This white plastic spacer fits into the back of the right hand inner knob on cars without factory fader or balance. If your inner knob is loose and will not align, you will want to see if this part is in place. 1968-70 AM-FM radios would not utilize this part because they have a balance feature. 1967 AM-FM radios would use this part as they did not have a balance feature. Called a "Sleeve" 1969-70 Cougar and Mustang AM radios use this sleeve. Also found on various 1970-76 Ford and Mercury cars...

For most applications, we highly suggest you upgrade to our solid state version of this unit.  Ford part # C9WY-13350-A, Ford service replacement part # D0WY-13350-A. *NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's and is the designer of all of our solid state sequential systems. There is no question he cannot answer! Here is a link to a great source of information on...

Curved aluminum cable guide as seen on page 13 of the sun roof manual. Golde part number 100 413 682

Curved aluminum cable guide as seen on page 13 of the sun roof manual. Golde part number 100 413 681

Front guide that measures 10 5/8" long held in place by four screws. The driver side has no markings but the passenger side is stamped with an R and the inner 2 screw holes are in a different place than the passenger.

Guide that measures 10 5/8" long held in place by the outer trim that has four screws. Driver and Passenger are interchangeable.

This part mates to and is held down by Golde #100 413 681. The Golde part number for the smaller, lower elbow guide is 100 413 664

This strip has a series of five retaining clips that hold the headlining panel to the roof panels as seen on page 14 of the sun roof manual.This is for the 1971-73 Mercury Cougar with factory sunroof. Sunroof measurements are roughly 19-1/2 x 39 inches. This panel is 32-1/4 inches long with 5 clips as shown.

Used sleeve for fixed steering wheel. Special molded rubber sleeve that holds the bearing in place.  Ford part # D1AZ-3518 or E2AZ-3518

If you have already begun to install or have installed this item, it is not eligible for return or refund. This is far superior to the switch Ford put out as a service part in the 90's. It is imperative that you clean every part of your old switch out before carefully installing the new switch. It is best to start both ends at the same time at 6 o'clock and meet at the middle at 12 o'clock. It measures 44" in length. We've found that these switches are about an inch too long, so you'll...

Correct nut that is designed not to come undone.

Reproduction walking cat center emblem for the 69 Cougar rim blow steering wheel.

Reproduction Chrome / Black Leather steering wheel for your 68 - 73 Mercury Cougar. This kit includes: Steering wheel, hub, horn button and center decal. Hardware included.

Reproduction Chrome / Woodgrain steering wheel for your 68 - 73 Mercury Cougar. This kit includes: Steering wheel, hub, horn button and center decal. Hardware included.

Reproduction Chrome / Dark Mahogany Woodgrain steering wheel for your 68 - 73 Mercury Cougar. This kit includes: Steering wheel, hub, horn button and center decal. Hardware included.

Reproduction Black Steel / Black Leather steering wheel for your 68 - 73 Mercury Cougar. This kit includes: Steering wheel, hub, horn button and center decal. Hardware included.

Reproduction thick grip Mahogany Woodgrain / Chrome steering wheel for your 68 - 73 Mercury Cougar. This kit includes: Steering wheel, hub, horn button and center decal. Hardware included.

Reproduction Chrome / Black Leather 4 spoke steering wheel for your 68 - 73 Mercury Cougar. This kit includes: Steering wheel, hub, horn button and center decal. Hardware included.

Reproduction reinforcement plate designed to weld onto the lower control arms. Sold individually, we are not sure that you would want to even buy one of these. They don't fit very well, and are not contoured to any lower control arm on the market. You will be bending these to fit, prior to welding. *Note - This is a non-returnable item. 

Brand new flex plate for all 1967-69 Mercury Cougar and Ford Mustang with any of the 390 engines. Also includes 1968 Cougar GT-E with 427-4V engines. Comes complete with new starter ring gear installed as shown. Neutral balance, meaning this has zero weights attached. *Note - Will not work on 428CJ engines.

C9ZP-7976-A Aluminum bell housing, sometimes called a converter housing in the Ford shop manual. 1969 Mercury Cougar and Ford Mustang with 351 engine and automatic FMX transmission, code X on your door data plate tag.

Used FMX transmission tail shaft or housing extension as Ford called them in the Master Parts Catalog. Fits all 1969-73 Mercury Cougar and Ford Mustang cars with transmission code X on the door tag. Cast aluminum construction. D2ZP-7A040-A version also available, we have a good supply of the updated 1972 version. The overall length of this housing is 12 7/8", which was also used on 1969 Fairlanes and Torinos.  This housing will not fit full sized Ford Mercury cars that have an FMX,...

Brand new flex plate for all 1969 - 73 Mercury Cougar and Ford Mustang with 302 / 351W / 351C engines, and C4, C6, or FMX transmissions. Comes complete with new starter ring gear installed as shown.*Note - Fits common torque converter bolt pattern of 11.40 inches. In 1972 there was a unique C6 torque converter with a 9.50 inch bolt pattern. 

Ultra rare C-6 transmission cast iron tail shaft for any 428 Cobra Jet or 429 Cobra Jet. Nice condition, has casting number RT-C8OP-7A040-A on side as shown. 1968-71 Mercury Cougar, Ford Mustang and Torino / Cyclone / Ranchero with Q or R code 428CJ engines including 428SCJ engines. J and C code 429CJ engines too for 1970-71.Ford MPC number C8OZ-7A039-B.

Good used OEM flex plate for all 69 - 73 Mercury Cougar and Ford Mustang with 302 / 351W engines, and C4 or FMX transmissions. Not for use on a 1968 with 302. The starter ring will show wear and some will choose to replace, others have removed the starter ring and just turned it around so the unused portion of the ring will now contact the starter drive gear. ...

New torque converter nuts for connecting torque converters to flex plates on 1967-73 Mercury Cougar or 1967-73 Ford Mustang or other Ford Lincoln Mercury that is not metric. 3/8-24 threads, Grade 8 nut with a 9/16 inch hex. 0.79" OD and 0.39" thick. Torque converters use 4 nuts for attachment.Ford number 377704-S

Set of 6 new correct bolts for attaching the FMX transmission to 351 engines. Fits all 1967-73 Mercury Cougar and 1967-73 Ford and Mustang with transmission code X, or FMX automatic transmissions. Quality fasteners from AMK.

Used FMX transmission tail shaft or housing extension as Ford called them in the Master Parts Catalog. Fits all 1969-73 Mercury Cougar and Ford Mustang cars with transmission code X on the door tag. Cast aluminum construction. C9ZP-7A040-A version also available for slightly more money. Exact same part, just got updated for some engineering or manufacturing reason. The overall length of this housing is 12 7/8", which was also used on 1969 Fairlanes and Torinos.  This housing will not...

Replacement seal with boot for all 1969-73 FMX and 1967-73 C6 transmissions. Tail shaft and slip yoke seal. 

Replacement seal with boot for all 1965-73 C4 Ford transmissions. Tail shaft and slip yoke seal. 

Replacement tail shaft bushing, for all 1969-73 FMX and 1967-73 C6 transmissions. 

Shift kit for the C6 transmission valve body for all 1967-73 and 1967-73 Mercury and Ford. This is a standard shift rebuilding kit for your stock valve body.

Shift kit for the FMX transmission valve body for all 1969-72 and 1969-72 Mercury and Ford. This is a standard shift rebuilding kit for your stock valve body.* Note - 1973 has a different shift kit, see related items.

Filter / screen for the C6 transmissions, for all 1967-73 and 1967-73 Mercury and Ford. 

Replacement cork pan gasket for all 1965-73 C4 Ford transmissions. 

Cork pan gasket for the C6 transmission on any 1967-73 and 1967-73 Mercury and Ford. Rubber gasket also available.

Rubber pan gasket for the C6 transmission on any 1967-73 and 1967-73 Mercury and Ford. Cork gasket also available.

Transmission pan gasket for the FMX transmission on any 1969-73 and 1969-73 Mercury Cougar and Ford Mustang.

Basic C6 transmission rebuild kit. Kit includes gaskets, seals, bands, filter, modulator, everything as shown. Fits all Ford C6 transmissions for any 1967-73 Mercury Cougar or Ford Mustang with that U code C-6 transmission. Quality kit, same as supplied to professional shops. Big and small block C6's.

Basic FMX transmission rebuild kit. Kit includes gaskets, seals, bands, filter, modulator, everything as shown. Fits all Ford FMX transmissions for any 1969-73 Mercury Cougar or Ford Mustang with that X code FMX transmission. Quality kit, same as supplied to professional shops. 

O Ring gasket for all automatic transmission dip stick tubes. Replacement gasket for C4, C6, and FMX trans dip stick tubes 1967-73 Mercury Cougar and Ford and Mustang.

Replacement filter for FMX transmissions. Fits all Ford FMX transmissions for any 1969-73 Mercury Cougar or Ford Mustang with that X code FMX transmission. 

Upholstery components have an ETA of 10 - 12 weeks.White XR7 Convertible Vinyl Upholstery to cover the front buckets and rear seat. If you are wanting a vinyl kit that looks just like leather you will be disappointed every time... No matter what material that is used nothing looks 100% like leather over time. That being said this is a good quality set that over time will outlast leather and look good, just do not think you will fool any judges.*NOTE* This product will take 6 -...

Upholstery components have an ETA of 10 - 12 weeks.Dark Blue XR7 Vinyl Upholstery to cover the front buckets. If you are wanting a vinyl kit that looks just like leather you will be disappointed every time... No matter what material that is used nothing looks 100% like leather over time. That being said this is a good quality set that over time will outlast leather and look good, just do not think you will fool any judges.*NOTE* This product will take 4 – 6 weeks for delivery. ...

Upholstery components have an ETA of 10 - 12 weeks.XR7 Vinyl Dark Red Upholstery to cover the front buckets. If you are wanting a vinyl kit that looks just like leather you will be disappointed every time... No matter what material that is used nothing looks 100% like leather over time. That being said this is a good quality set that over time will outlast leather and look good, just do not think you will fool any judges.*NOTE* This product will take 4 – 6 weeks for delivery. ...

Upholstery components have an ETA of 10 - 12 weeks.Saddle XR7 Vinyl Upholstery to cover the front buckets. If you are wanting a vinyl kit that looks just like leather you will be disappointed every time... No matter what material that is used nothing looks 100% like leather over time. That being said this is a good quality set that over time will outlast leather and look good, just do not think you will fool any judges.*NOTE* This product will take 4 – 6 weeks for delivery. ...

Upholstery components have an ETA of 10 - 12 weeks.Dark Ivy Gold / Dark Green XR7 Vinyl Upholstery to cover the front buckets. If you are wanting a vinyl kit that looks just like leather you will be disappointed every time... No matter what material that is used nothing looks 100% like leather over time. That being said this is a good quality set that over time will outlast leather and look good, just do not think you will fool any judges. *NOTE* This product will take 4 – 6 weeks for...

Upholstery components have an ETA of 10 - 12 weeks.Light Aqua XR7 Vinyl Upholstery to cover the front buckets. If you are wanting a vinyl kit that looks just like leather you will be disappointed every time... No matter what material that is used nothing looks 100% like leather over time. That being said this is a good quality set that over time will outlast leather and look good, just do not think you will fool any judges.*NOTE* This product will take 4 – 6 weeks for delivery. ...

Upholstery components have an ETA of 10 - 12 weeks.Nugget Gold XR7 Vinyl Upholstery to cover the front buckets. If you are wanting a vinyl kit that looks just like leather you will be disappointed every time... No matter what material that is used nothing looks 100% like leather over time. That being said this is a good quality set that over time will outlast leather and look good, just do not think you will fool any judges.*NOTE* This product will take 4 – 6 weeks for delivery. ...

Upholstery components have an ETA of 10 - 12 weeks.White XR7 Vinyl Upholstery to cover the front buckets. If you are wanting a vinyl kit that looks just like leather you will be disappointed every time... No matter what material that is used nothing looks 100% like leather over time. That being said this is a good quality set that over time will outlast leather and look good, just do not think you will fool any judges.*NOTE* This product will take 4 – 6 weeks for delivery. ...

Upholstery components have an ETA of 10 - 12 weeks.Black Convertible Vinyl Upholstery to cover the rear seat. If you are wanting a vinyl kit that looks just like leather you will be disappointed every time... No matter what material that is used nothing looks 100% like leather over time. That being said this is a good quality set that over time will outlast leather and look good, just do not think you will fool any judges.*NOTE* This product will take 4 – 6 weeks for delivery. ...

Upholstery components have an ETA of 10 - 12 weeks.XR7 Dark Blue Convertible Vinyl Upholstery to cover the rear seat. If you are wanting a vinyl kit that looks just like leather you will be disappointed every time... No matter what material that is used nothing looks 100% like leather over time. That being said this is a good quality set that over time will outlast leather and look good, just do not think you will fool any judges.*NOTE* This product will take 4 – 6 weeks for delivery. ...

Upholstery components have an ETA of 10 - 12 weeks.Dark Red XR7 Vinyl Upholstery to cover the rear seat. If you are wanting a vinyl kit that looks just like leather you will be disappointed every time... No matter what material that is used nothing looks 100% like leather over time. That being said this is a good quality set that over time will outlast leather and look good, just do not think you will fool any judges.*NOTE* This product will take 4 – 6 weeks for delivery. ...

Upholstery components have an ETA of 10 - 12 weeks.Saddle XR7 Vinyl Upholstery to cove the rear seat. If you are wanting a vinyl kit that looks just like leather you will be disappointed every time... No matter what material that is used nothing looks 100% like leather over time. That being said this is a good quality set that over time will outlast leather and look good, just do not think you will fool any judges.*NOTE* This product will take 4 – 6 weeks for delivery. ...

Upholstery components have an ETA of 10 - 12 weeks.Dark Ivy Gold / Dark Green XR7 Convertible Vinyl Upholstery to cover the rear seat. If you are wanting a vinyl kit that looks just like leather you will be disappointed every time... No matter what material that is used nothing looks 100% like leather over time. That being said this is a good quality set that over time will outlast leather and look good, just do not think you will fool any judges. *NOTE* This product will take 4 – 6 weeks for...

Upholstery components have an ETA of 10 - 12 weeks.Light Aqua XR7 Convertible Vinyl Upholstery to cover the rear seat. If you are wanting a vinyl kit that looks just like leather you will be disappointed every time... No matter what material that is used nothing looks 100% like leather over time. That being said this is a good quality set that over time will outlast leather and look good, just do not think you will fool any judges.*NOTE* This product will take 6 - 8 weeks for...

Upholstery components have an ETA of 10 - 12 weeks.Nugget Gold XR7 Convertible Vinyl Upholstery to cover the rear seat. If you are wanting a vinyl kit that looks just like leather you will be disappointed every time... No matter what material that is used nothing looks 100% like leather over time. That being said this is a good quality set that over time will outlast leather and look good, just do not think you will fool any judges.*NOTE* This product will take 4 – 6 weeks for delivery. ...

Upholstery components have an ETA of 10 - 12 weeks.White XR7 Convertible Vinyl Upholstery to cover the rear seat. If you are wanting a vinyl kit that looks just like leather you will be disappointed every time... No matter what material that is used nothing looks 100% like leather over time. That being said this is a good quality set that over time will outlast leather and look good, just do not think you will fool any judges.*NOTE* This product will take 6 - 8 weeks for delivery. ...

Upholstery components have an ETA of 10 - 12 weeks.Door Tag Trim Code: 2A.    Black Decor Interior Upholstery Kit to cover the front buckets and rear seat. Correct rhino grain, laser straight stitching and correct colors. Notice the detail on the horizontal simulated stitched band. This strip has been correctly reproduced in all the original colors. Many vendors skip this part or reuse your old, hardened strip. Your satisfaction is guaranteed, no excuses. *NOTE* Some of the more...

Upholstery components have an ETA of 10 - 12 weeks.Door Tag Trim Code: 2B.    Light Blue Decor Interior Upholstery to cover the front buckets and rear seat. Correct rhino grain, laser straight stitching and correct colors. Notice the detail on the horizontal simulated stitched band. This strip has been correctly reproduced in all the original colors. Many vendors skip this part or reuse your old, hardened strip. Your satisfaction is guaranteed, no excuses.*NOTE* Some of the more...

Upholstery components have an ETA of 10 - 12 weeks.Door Tag Trim Code: 2D.    Dark Red Decor to cover the front buckets and rear seat for the 1969 Mercury Cougar Coupe. Correct rhino grain, laser straight stitching and correct colors. Notice the detail on the horizontal simulated stitched band. This strip has been correctly reproduced in all the original colors. Many vendors skip this part or reuse your old, hardened strip. Your satisfaction is guaranteed, no excuses.*NOTE* Some of...

Upholstery components have an ETA of 10 - 12 weeks.Door Tag Trim Code: 2F.    Saddle Decor Upholstery to cover the front buckets and rear seat. Correct rhino grain, laser straight stitching and correct colors. Notice the detail on the horizontal simulated stitched band. This strip has been correctly reproduced in all the original colors. Many vendors skip this part or reuse your old, hardened strip. Your satisfaction is guaranteed, no excuses.*NOTE* Some of the more unique colors...

Upholstery components have an ETA of 10 - 12 weeks. Door Tag Trim Code: 2G. Light Ivy Gold / Light Green Decor Upholstery to cover the front buckets and rear seat. Correct rhino grain, laser straight stitching and correct colors. Notice the detail on the horizontal simulated stitched band. This strip has been correctly reproduced in all the original colors. Many vendors skip this part or reuse your old, hardened strip. Your satisfaction is guaranteed, no excuses. *NOTE* Some of the more unique...

Upholstery components have an ETA of 10 - 12 weeks.Door Tag Trim Code: 2K.    Aqua Decor Upholstery to cover the front buckets and rear seat. Correct rhino grain, laser straight stitching and correct colors. Notice the detail on the horizontal simulated stitched band. This strip has been correctly reproduced in all the original colors. Many vendors skip this part or reuse your old, hardened strip. Your satisfaction is guaranteed, no excuses.*NOTE* Some of the more unique colors like...

Upholstery components have an ETA of 10 - 12 weeks.Door Tag Trim Code: 2Y.    Nugget Gold Decor Upholstery to cover the front buckets and rear seat. Correct rhino grain, laser straight stitching and correct colors. Notice the detail on the horizontal simulated stitched band. This strip has been correctly reproduced in all the original colors. Many vendors skip this part or reuse your old, hardened strip. Your satisfaction is guaranteed, no excuses.*NOTE* Some of the more unique...

Upholstery components have an ETA of 10 - 12 weeks.Door Tag Trim Codes that start with: B.    White Decor Upholstery to cover the front buckets and rear seat. Correct rhino grain, laser straight stitching and correct colors. Notice the detail on the horizontal simulated stitched band. This strip has been correctly reproduced in all the original colors. Many vendors skip this part or reuse your old, hardened strip. Your satisfaction is guaranteed, no excuses.*NOTE* Some of the more...

Upholstery components have an ETA of 10 - 12 weeks.When ordering interior seat kits from us there is no need for you to send in a sample for us to match. We have the original "Color-Upholstery Selection" binders found at the Mercury dealership in the day. These binders have actual pieces of the vinyl, leather and cloth used in the Cougars originally. These binders (or showroom albums) were used by the salesmen to assist in selecting paint and interior combinations on their new Mercury. We use...

Upholstery components have an ETA of 10 - 12 weeks. When ordering interior seat kits from us there is no need for you to send in a sample for us to match. We have the original "Color-Upholstery Selection" binders found at the Mercury dealership in the day. These binders have actual pieces of the vinyl, leather and cloth used in the Cougars originally. These binders (or showroom albums) were used by the salesmen to assist in selecting paint and interior combinations on their new Mercury. We use...

Upholstery components have an ETA of 10 - 12 weeks.These are NOT modified Mustang interior kits! When ordering interior seat kits from us there is no need for you to send in a sample for us to match. We have the original "Color-Upholstery Selection" binders found at the Mercury dealership in the day. These binders have actual pieces of the vinyl, leather and cloth used in the Cougars originally. These binders (or showroom albums) were used by the salesmen to assist in selecting paint and...

Upholstery components have an ETA of 10 - 12 weeks.These are NOT modified Mustang interior kits! When ordering interior seat kits from us there is no need for you to send in a sample for us to match. We have the original "Color-Upholstery Selection" binders found at the Mercury dealership in the day. These binders have actual pieces of the vinyl, leather and cloth used in the Cougars originally. These binders (or showroom albums) were used by the salesmen to assist in selecting paint and...

Upholstery components have an ETA of 10 - 12 weeks.When ordering interior seat kits from us there is no need for you to send in a sample for us to match. We have the original "Color-Upholstery Selection" binders found at the Mercury dealership in the day. These binders have actual pieces of the vinyl, leather and cloth used in the Cougars originally. These binders (or showroom albums) were used by the salesmen to assist in selecting paint and interior combinations on their new Mercury. We use...

Upholstery components have an ETA of 10 - 12 weeks.When ordering interior seat kits from us there is no need for you to send in a sample for us to match. We have the original "Color-Upholstery Selection" binders found at the Mercury dealership in the day. These binders have actual pieces of the vinyl, leather and cloth used in the Cougars originally. These binders (or showroom albums) were used by the salesmen to assist in selecting paint and interior combinations on their new Mercury. We use...

Upholstery components have an ETA of 10 - 12 weeks. These are NOT modified Mustang interior kits! When ordering interior seat kits from us there is no need for you to send in a sample for us to match. We have the original "Color-Upholstery Selection" binders found at the Mercury dealership in the day. These binders have actual pieces of the vinyl, leather and cloth used in the Cougars originally. These binders (or showroom albums) were used by the salesmen to assist in selecting paint and...

Upholstery components have an ETA of 10 - 12 weeks.These are NOT modified Mustang interior kits! When ordering interior seat kits from us there is no need for you to send in a sample for us to match. We have the original "Color-Upholstery Selection" binders found at the Mercury dealership in the day. These binders have actual pieces of the vinyl, leather and cloth used in the Cougars originally. These binders (or showroom albums) were used by the salesmen to assist in selecting paint and...

Upholstery components have an ETA of 10 - 12 weeks.When ordering interior seat kits from us there is no need for you to send in a sample for us to match. We have the original "Color-Upholstery Selection" binders found at the Mercury dealership in the day. These binders have actual pieces of the vinyl, leather and cloth used in the Cougars originally. These binders (or showroom albums) were used by the salesmen to assist in selecting paint and interior combinations on their new Mercury. We use...

Upholstery components have an ETA of 10 - 12 weeks.These are NOT modified Mustang interior kits! When ordering interior seat kits from us there is no need for you to send in a sample for us to match. We have the original "Color-Upholstery Selection" binders found at the Mercury dealership in the day. These binders have actual pieces of the vinyl, leather and cloth used in the Cougars originally. These binders (or showroom albums) were used by the salesmen to assist in selecting paint and...

Upholstery components have an ETA of 10 - 12 weeks.Door Tag Trim Code: 2A. Black Decor to cover the rear seat of the 1969 Mercury Cougar coupe.

Upholstery components have an ETA of 10 - 12 weeks.Door Tag Trim Code: 2B. Light Blue Decor Upholstery to cover the rear seat. *NOTE* This product will take 4 – 6 weeks for delivery.

Upholstery components have an ETA of 10 - 12 weeks.Dark Red Upholstery to cover the rear seat for the 1969 Mercury Cougar Coupe. Correct rhino grain, laser straight stitching and correct colors. Notice the detail on the horizontal simulated stitched band. This strip has been correctly reproduced in all the original colors. Many vendors skip this part or reuse your old, hardened strip. Your satisfaction is guaranteed, no excuses... These come direct from the manufacture, please allow 2 - 3...

Upholstery components have an ETA of 10 - 12 weeks.Saddle Decor Upholstery to cover the rear seat. Correct rhino grain, laser straight stitching and correct colors. Notice the detail on the horizontal simulated stitched band. This strip has been correctly reproduced in all the original colors. Many vendors skip this part or reuse your old, hardened strip. Your satisfaction is guaranteed, no excuses.*NOTE* Some of the more unique colors like aqua are not always guaranteed to be in stock at all...

Upholstery components have an ETA of 10 - 12 weeks. Light Ivy Gold / Light Green Decor Upholstery to cover the rear seat. Correct rhino grain, laser straight stitching and correct colors. Notice the detail on the horizontal simulated stitched band. This strip has been correctly reproduced in all the original colors. Many vendors skip this part or reuse your old, hardened strip. Your satisfaction is guaranteed, no excuses. *NOTE* Some of the more unique colors like aqua are not always...

Upholstery components have an ETA of 10 - 12 weeks.Aqua Decor Upholstery to cover the rear seat. Correct rhino grain, laser straight stitching and correct colors. Notice the detail on the horizontal simulated stitched band. This strip has been correctly reproduced in all the original colors. Many vendors skip this part or reuse your old, hardened strip. Your satisfaction is guaranteed, no excuses.*NOTE* Some of the more unique colors like aqua are not always guaranteed to be in stock at all...

Upholstery components have an ETA of 10 - 12 weeks.Nugget Gold Decor Upholstery to cover the rear seat. Correct rhino grain, laser straight stitching and correct colors. Notice the detail on the horizontal simulated stitched band. This strip has been correctly reproduced in all the original colors. Many vendors skip this part or reuse your old, hardened strip. Your satisfaction is guaranteed, no excuses.*NOTE* Some of the more unique colors like aqua are not always guaranteed to be in stock at...

Upholstery components have an ETA of 10 - 12 weeks.White Decor Upholstery to cover the rear seat. Correct rhino grain, laser straight stitching and correct colors. Notice the detail on the horizontal simulated stitched band. This strip has been correctly reproduced in all the original colors. Many vendors skip this part or reuse your old, hardened strip. Your satisfaction is guaranteed, no excuses.*NOTE* Some of the more unique colors like aqua are not always guaranteed to be in stock at all...

Upholstery components have an ETA of 10 - 12 weeks.When ordering interior seat kits from us there is no need for you to send in a sample for us to match. We have the original "Color-Upholstery Selection" binders found at the Mercury dealership in the day. These binders have actual pieces of the vinyl, leather and cloth used in the Cougars originally. These binders (or showroom albums) were used by the salesmen to assist in selecting paint and interior combinations on their new Mercury. We use...

Upholstery components have an ETA of 10 - 12 weeks.These are NOT modified Mustang interior kits! When ordering interior seat kits from us there is no need for you to send in a sample for us to match. We have the original "Color-Upholstery Selection" binders found at the Mercury dealership in the day. These binders have actual pieces of the vinyl, leather and cloth used in the Cougars originally. These binders (or showroom albums) were used by the salesmen to assist in selecting paint and...

Upholstery components have an ETA of 10 - 12 weeks. These are NOT modified Mustang interior kits! When ordering interior seat kits from us there is no need for you to send in a sample for us to match. We have the original "Color-Upholstery Selection" binders found at the Mercury dealership in the day. These binders have actual pieces of the vinyl, leather and cloth used in the Cougars originally. These binders (or showroom albums) were used by the salesmen to assist in selecting paint and...

Upholstery components have an ETA of 10 - 12 weeks.These are NOT modified Mustang interior kits! When ordering interior seat kits from us there is no need for you to send in a sample for us to match. We have the original "Color-Upholstery Selection" binders found at the Mercury dealership in the day. These binders have actual pieces of the vinyl, leather and cloth used in the Cougars originally. These binders (or showroom albums) were used by the salesmen to assist in selecting paint and...

Upholstery components have an ETA of 10 - 12 weeks.Black XR7 Vinyl Upholstery to cover the front buckets and rear seat. If you are wanting a vinyl kit that looks just like leather you will be disappointed every time... No matter what material that is used nothing looks 100% like leather over time. That being said this is a good quality set that over time will outlast leather and look good, just do not think you will fool any judges.*NOTE* This product will take 6 - 8 weeks for...

Upholstery components have an ETA of 10 - 12 weeks.XR7 Dark Blue Coupe Vinyl Upholstery to cover the front buckets and rear seat. If you are wanting a vinyl kit that looks just like leather you will be disappointed every time... No matter what material that is used nothing looks 100% like leather over time. That being said this is a good quality set that over time will outlast leather and look good, just do not think you will fool any judges.

Upholstery components have an ETA of 10 - 12 weeks.Dark Red Vinyl Upholstery to cover the front buckets and rear seat. If you are wanting a vinyl kit that looks just like leather you will be disappointed every time... No matter what material that is used nothing looks 100% like leather over time. That being said this is a good quality set that over time will outlast leather and look good, just do not think you will fool any judges.*NOTE* This product will take 6 - 8 weeks for...

Upholstery components have an ETA of 10 - 12 weeks. Saddle XR7 Vinyl Upholstery to cover the front buckets and rear seat. If you are wanting a vinyl kit that looks just like leather you will be disappointed every time... No matter what material that is used nothing looks 100% like leather over time. That being said this is a good quality set that over time will outlast leather and look good, just do not think you will fool any judges.

Upholstery components have an ETA of 10 - 12 weeks.Dark Ivy Gold / Dark Green XR7 Coupe Vinyl Upholstery to cover the front buckets and rear seat. If you are wanting a vinyl kit that looks just like leather you will be disappointed every time... No matter what material that is used nothing looks 100% like leather over time. That being said this is a good quality set that over time will outlast leather and look good, just do not think you will fool any judges. *NOTE* This product will...

Upholstery components have an ETA of 10 - 12 weeks.Light Aqua XR7 Coupe Vinyl Upholstery to cover the front buckets and rear seat. If you are wanting a vinyl kit that looks just like leather you will be disappointed every time... No matter what material that is used nothing looks 100% like leather over time. That being said this is a good quality set that over time will outlast leather and look good, just do not think you will fool any judges.*NOTE* This product will take 6 - 8 weeks for...

Upholstery components have an ETA of 10 - 12 weeks.Nugget Gold XR7 Coupe Vinyl Upholstery to cover the front buckets and rear seat. If you are wanting a vinyl kit that looks just like leather you will be disappointed every time... No matter what material that is used nothing looks 100% like leather over time. That being said this is a good quality set that over time will outlast leather and look good, just do not think you will fool any judges.*NOTE* This product will take 6 -...

Upholstery components have an ETA of 10 - 12 weeks.White XR7 Coupe Vinyl Upholstery to cover the front buckets and rear seat. If you are wanting a vinyl kit that looks just like leather you will be disappointed every time... No matter what material that is used nothing looks 100% like leather over time. That being said this is a good quality set that over time will outlast leather and look good, just do not think you will fool any judges.*NOTE* This product will take 6 - 8 weeks for...

Upholstery components have an ETA of 10 - 12 weeks.Black XR7 Vinyl Upholstery to cover the front buckets. If you are wanting a vinyl kit that looks just like leather you will be disappointed every time... No matter what material that is used nothing looks 100% like leather over time. That being said this is a good quality set that over time will outlast leather and look good, just do not think you will fool any judges.*NOTE* This product will take 4 – 6 weeks for delivery. ...

Upholstery components have an ETA of 10 - 12 weeks.Black XR7 Vinyl Upholstery to cover the rear seat. If you are wanting a vinyl kit that looks just like leather you will be disappointed every time... No matter what material that is used nothing looks 100% like leather over time. That being said this is a good quality set that over time will outlast leather and look good, just do not think you will fool any judges.*NOTE* This product will take 4 – 6 weeks for delivery. ...

Upholstery components have an ETA of 10 - 12 weeks.Dark Red XR7 Vinyl Upholstery to cover the rear seat. If you are wanting a vinyl kit that looks just like leather you will be disappointed every time... No matter what material that is used nothing looks 100% like leather over time. That being said this is a good quality set that over time will outlast leather and look good, just do not think you will fool any judges.*NOTE* This product will take 4 – 6 weeks for delivery. ...