1973 Ford Mustang

This is the storage bag that the convertible top cover folds into when the top is in the down position. Ford calls this part the "Folding top dust hood container." It is made from common vinyl top material and is always black. It measures 15"x27" and the bottom portion is sometimes, tapered down to 8". The same design was used for many Ford Products of the day including Torino, Montego and others. Current offering does not have a tapered bottom, it is square. Pictures will show both styles...

Rear most convertible top bow #4, from a 1971-73 Mercury Cougar or Ford Mustang convertible top assembly. This is the last bow and would have had a tack strip attached.   Ford part number D1ZZ-7651278-A.

Used mounting bracket from a 1971-73 Mercury Cougar or Ford Mustang with factory installed air conditioning. This is the tab that is riveted to the blower housing, the stud goes through the firewall. Bracket with stud only, no other hardware included. Normally this will ship with the old fiberglass remnants still riveted to this bracket. 

This bracket connects the battery hold down clamp to the fender apron to stop the battery from rocking from side to side. Most cars are missing this crucial part to stabilize the battery. Replaces Ford Part #: D0OZ-10757-A.

This bracket connects the battery hold down clamp to the fender apron to stop the battery from rocking from side to side. Most cars are missing this crucial part to stabilize the battery. Original used bracket, not reproduction. Replaces Ford Part #: D0OZ-10757-A.

Reproduction bracket assembly for mounting the J hood and inflator cannister. Trunk plate or bracket for mounting the "J" bolt for the spare tire also included is the saddle bracket for mounting the tire inflator cannister. Mounts on the top of the trunk floor surface. 1969-70 Mercury Cougar convertibles and hard tops with space saver spare tires. Additionally, 1971-73 Mercury Cougar hard tops. *Trivia - According to the Concours Mustang Forum, this bracket wasn't installed or available...

Used bracket assembly for mounting the J hood and inflator cannister. Trunk plate or bracket for mounting the "J" bolt for the spare tire also included is the saddle bracket for mounting the tire inflator cannister. Mounts on the top of the trunk floor surface. 1969-70 Mercury Cougar convertibles and hard tops with space saver spare tires. Additionally, 1971-73 Mercury Cougar hard tops. We cut these out of the trunk floors, so there will be some metal preparation for the customer. Rare...

Driver side convertible frame assembly mounting and pivot bracket for all 1971-73 Mercury Cougar and Ford Mustang. Does not include the hydraulic cylinder bracket, cylinder mounting bracket sold separately. Bushings, bolts, and specialty fasteners not included. Mounts behind the quarter interior panel.  Ford part number D1ZZ-7653119-A.

Passenger side convertible frame assembly mounting and pivot bracket for all 1971-73 Mercury Cougar and Ford Mustang. Does not include the hydraulic cylinder bracket, cylinder mounting bracket sold separately. Bushings, bolts, and specialty fasteners not included. Mounts behind the quarter interior panel.  Ford part number D1ZZ-7653118-A.

Detachable mounting plate for installing the convertible ram cylinder to the convertible top frame assembly behind the quarter interior panel. Right and left are the same, fits all 1971-73 Mercury Cougar and Ford Mustang convertibles. Ford part number D1ZZ-76531A19-A.

Used bracket for installing the rear interior panels on any 1971-73 Mercury Cougar or Ford Mustang convertible. One bracket per side. These brackets will have a bit of dirt and or rust on them, originally painted chassis black. Replaces Ford part number D1ZZ-76310A84-A. 

Crank case hose bracket for any 1971-73 Mercury Cougar and Ford Mustang at least with V-8 engines. Attaches to the intake manifold, a black plastic ring clip large enough for the vent hose is attached to the small hole. Limited supply, most of these go missing during an engine tear down. Ford part number D1AZ-6788-A.