All Available Parts - 1972 Ford Mustang

Locking pawl catch pin and locking pawl pin for your 70-73 Lincoln - Mercury - Ford tilt steering columns. This is an improved reproduction with cir-clips to prevent movement, avoiding damage to you locking pawl. These shafts are notorious for working their way out of place with normal use. Once the pin works its way out the locking pawl will not be aligned with the teeth and the cast part will break under pressure. Upgrading to these parts can avoid several hundred dollars in damage. These...

This linkage fits between the gear at the bottom of the key lock and rod that goes to the ignition switch on the fixed column.*NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year. Ford part number D0AA-3E715-D

Locking pawl pin for your 70 - 79 tilt steering column for all Lincoln - Mercury - Ford products. This is an improved reproduction with cir-clips to prevent movement, avoiding damage to your locking pawl. These shafts are notorious for working their way out of place with normal use. Once the pin works its way out the locking pawl will not be aligned with the teeth and the cast part will break under pressure. Upgrading to this part can avoid several hundred dollars in damage. This precision...

New axle bearing for any 8 or 9 inch Ford rear end with 28 splined axles. Common on all Mercury Cougar and Ford Mustang with V-8 engines. Excludes 31 splined axles as found on Boss and Cobra Jet cars.These should be professionally installed with a bearing press.

New outer axle gasket for any 8 or 9 inch Ford rear end with 28 splined axles. Common on all Mercury Cougar and Ford Mustang with V-8 engines. Excludes 31 splined axles as found on Boss and Cobra Jet cars. One required per side, two per car.

Rear axle vent bolt for the 67 - 73 Cougar or Mustang. This bolt serves a dual purpose, as it also holds the brake line bracket in place on the axle tube.

Used pinion yoke for an 8 inch rear end on any 1967-68 Mercury Cougar or 1967-73 Ford Mustang. 25 splines Ford says it is for a 1260 U-Joint. Part cleaned for pictures, used parts shipped the way they come off of the cars. Shipped bare, no hardware included.Ford part number C3OZ-4851-A.

Nuts and washers for attaching the rear differential carrier or pumpkin or third member to the rear axle housing. Correct for all 1969-73 Mercury Cougar and 1969-73 Ford Mustang. 8 inch or 9 inch third members, all the same.

New pinion seal for any 8 inch third member found in 1967-73 Ford and Mercury cars. 1967-68 Mercury Cougar and all years of Mustang with 8 inch drop out rears.

Reproduction anti-squeak pad for the leaf springs found on the Mercury Cougar or Ford Mustang. This little unit goes between each individual leaf spring and prevents metal to metal contact. These are sold individually and eight are required per car. Our reproduction leaf springs come with this pad pre-installed. Replaces Ford part # C0AA-5586.

This is the bushing that Ford lists as the REAR stabilizer end link bushing, but it works for both front and rear. Smaller image shows a comparison of the NOS(Left) and Repro (right). SOLD INDIVIDUALLY. Replaces Ford Part #: KC-55490-A.

This is the bushing that Ford lists as the REAR stabilizer end link bushing, but it works for both front and rear. Smaller image shows a comparison of the NOS(Left) and Repro (right). SOLD AS SET OF 8. Replaces Ford Part #: KC-55490-A.

Sold individually. Has correct flattened area at top. Competition handling size, measures 7" from inner radius to end of threads. Thread size 7/16-20".  Does not include the OEM style nuts, those are an optional addon.  Replaces Ford Part #: C6OA-5705-C

These coarse thread nuts have an integrated lock washer with serations for the Mercury Cougar or Ford Mustang. They will ONLY work with the U-Bolts used in conjunction with the lowering kits. The thread size is 7/16"-14. *NOTE* Eight of these are required per car and are sold individually.

All applications, attaches the drive shaft U-Joint to rear end pinion yoke. Sold in pairs, complete with nuts. Perfect used. Ford Part #: C1AZ-4529-A or D3AZ-4529-A.

Reproduction universal joint forged from high strength alloy steel and crossed w/ and anti-corrosion coating. Fits the differential end of the drive axle on all 289, 302, 351 Windsor as well as most 351 Clevelands (See Chart). Includes a grease fitting for an extended life. 3.25" span cups are 1.12" and 1.00" diam. Replaces Ford part # C3AZ-4635-F.

Reproduction front universal joint that fits on transmission end of the drive axle on Mercury Cougars or Ford Mustangs equipped with the 390, 427, 428, 429 and some 351 Clevelands (see chart). Includes a grease fitting for an extended life. Replaces Ford part # C3AZ-4635-G.

Reproduction universal joint forged from high strength alloy steel that is cross w/ an anti-corrosion coating. This unit fits the transmission end drive axle on Mercury Cougars or Ford Mustangs equipped with the 390, 427, 428, 429 and some 351 Clevelands (See Chart). this unit also features a grease fitting for an extended life. span 3.60" cup size 1.00" and 1.00"  Replaces Ford part # C3AZ-4635-G.

This reproduction universal joint fits the differential end of the drive axle on all Eliminators and other cars equipped with the 390, 427, 428, 429 and some 351 Clevelands (see chart). Includes grease fitting for extended life. Replaces Ford part # C3AZ-4635-H.

Reproduction alloy rear universal joint for the Mercury Cougar or Ford Mustang. This unit is forged from high strength alloy steel crossed w/ an anti-corrosion coating. This universal joint fits the differential end of the drive axle on all Eliminators and cars equipped with the 390, 427, 428, 429 and some 351 Clevelands (see chart). Includes grease fitting for extended life. span 3.5" cup size 1.00" and 1.12" Replaces Ford part # C3AZ-4635-H. ...

These Linear springs are custom wound for the performance-oriented customer. These feature 600-pound/inch rating and will lower the car approximately one inch from stock. Painted black, sold as a pair. Note: If you look close at factory sales pictures from the day you will notice the cars sit about 1" lower in back than front. These springs will level the car out provided your rear leaf springs are not sagging.  Linear springs are the easiest to understand. When you think of a spring,...

Made from soft flexible rubber very similar to the OEM material. Sold individually. Two required per vehicle. These are the coil spring insulators available from most Mustang/Cougar suppliers. If you prefer polyurethane insulators, you can find them here. Replaces Ford Part #: C4DZ-5415-A.

Reproduction rubber dust seal or boot for front suspension upper and lower tie rod ends. 1970-73 Mercury Cougar, Ford Mustang, and many other Ford cars.Replaces Ford part # D0OZ-3332

Reproduction rear axle outer bumper for the Mercury Cougar or Ford Mustang. These units mount on frame rail, are push in and two are required per car. Sold as a pair. Replaces Ford part # C6AZ-4730.

Black rubber bushings that are exact copies of the original Ford bushings. Features correct shoulder and split for easy installation. Sold in pairs. Replaces Ford Part #: C6OZ-5493-E

Front sway bar end link kits for all classic Cougars. 1967 - 1973 Kit includes spacer, bolt, insulators, nuts, and washers. All new hardware. Kit includes 2 links. Replaces Ford part # C2OZ-5A486-A.

Reproduction sway bar clamp and rubber bushing set for 1" sway bars on 1967 - 1973 big block Cougars and Mustangs. 

Reproduction sway bar clamp and bushing set for 3/4" sway bars on 1967 - 1973 Cougars and Mustangs.  These polyurethane bushings reduce deflection at the bar mounts to quicken the action of stock or aftermarket sway bars, and come with matching mount brackets. Includes lubrication groove to prevent squeaking. Replaces Ford Part #: C5ZZ-5486-H

Bolt kit for installing front sway bar clamps to the body for any 1969-73 Mercury Cougar or Ford Mustang. 5/16" bolts for 1969-73 cars. Starting in 1969, the bolt size was changed from 3/8" to 5/16". We stock the 3/8" bolt kits, which was standard for 1967-68 cars. See related items.

Original sway bar mount for your 1971-73 Mercury Cougar or Ford Mustang. Nice original, removed from our better cars. Metal cleanup needed, we cut these a little generously to protect the bracket. Original part number is 5A483. The MPC and other manuals refer to this bracket as: reinforcement and mounting bracket for front stabilizer bar. One per side, right and left are the same. See related items.  

Used wire set for the dash plug from the main under dash wiring harness from any 1971-73 Mercury Cougar. Wire colors may vary.

Reproduction passenger side (right hand) tinted door glass for the Mercury Cougar or Ford Mustang coupe or convertible equipped with power windows. There are three versions of this glass. The clear version is just that

Reproduction driver side (left hand) tinted door glass for the Mercury Cougar or Ford Mustang coupe or convertible equipped with manually operated windows. There are three versions of this glass. The clear version is just that

Reproduction passenger side (right hand) tinted door glass for the Mercury Cougar or Ford Mustang coupe or convertible equipped with manually operated windows. There are three versions of this glass. The clear version is just that

Reproduction driver side (left hand) clear door glass for the Mercury Cougar or Ford Mustang coupe or convertible equipped with manually operated windows. There are three versions of this glass. The clear version is just that

Reproduction passenger side (right hand) clear door glass for the Mercury Cougar or Ford Mustang coupe or convertible equipped with manually operated windows. There are three versions of this glass. The clear version is just that

Reproduction driver side (left hand) clear door glass for the Mercury Cougar or Ford Mustang coupe or convertible equipped with power windows. There are three versions of this glass. The clear version is just that

Reproduction driver side (left hand) tinted door glass for the Mercury Cougar or Ford Mustang coupe or convertible equipped with power windows. There are three versions of this glass. The clear version is just that, clear with no tint. There is a tinted version that will have a slight green tint to the glass, SUN-X factory tint. There is also a second tinted version that is called smoked and this version has a grey / brown tint to the glass. The clear and the tinted versions are reproductions...

Reproduction power window conversion for your Cougar or Mustang. These kits are easy to install and bolt into the original mounting holes, and use your existing window channels. Once you install the kit, your window crank becomes the switch. Simply lift up on the crank to roll the window up, and press down on the crank to roll the window down. Made from quality materials like 1018 cold rolled steel, Oilite thrust bearings at the pivot points and treated metal for all the gears makes for a high...

Reproduction power window conversion for your Cougar or Mustang. These kits are easy to install and bolt into the original mounting holes, and use your existing window channels. Once you install the kit, your window crank becomes the switch. Simply lift up on the crank to roll the window up, and press down on the crank to roll the window down. Made from quality materials like 1018 cold rolled steel, Oilite thrust bearings at the pivot points and treated metal for all the gears makes for a high...

Complete six piece window glass set for the 1971

Reproduction six piece SUN-X or tinted glass set for the Mercury Cougar coupe equipped with or without power windows. This set does not come with any of the window trim so save yours for reuse. There are three versions of this glass. The clear version is just that

Reproduction CLEAR five piece glass set for the 1971-73 Mercury Cougar coupe or Ford Mustang hard top equipped with power or crank windows. This set does not include any of the window trim so save yours for reuse. There are three versions of this glass. The clear version is just that

Reproduction TINTED five piece glass set for the Mercury Cougar coupe equipped with either power windows or crank windows. This set does not include any of the window trim so save yours for reuse. There are three versions of this glass. The clear version is just that

Reproduction six piece extra dark tinted glass set for the Mercury Cougar coupe equipped with or without power windows. This set does not come with any of the window trim so save yours for reuse. There are three versions of this glass. The clear version is just that

Four piece CLEAR window glass set for the 1971

Complete five piece window glass set for the 1971

Reproduction tinted four piece glass set for the Mercury Cougar or Ford Mustang convertible equipped with manually operated windows. This set does not include any window trim so save your for reuse. There are three versions of this glass. The clear version is just that

Reproduction tinted four piece glass set for the Mercury Cougar or Ford Mustang convertible equipped with power windows. This set does not include any of the window trim so save yours for reuse. There are three versions of this glass. The clear version is just that

Reproduction clear four piece glass set for the Mercury Cougar or Ford Mustang convertible equipped with power windows. This set does not include any of the window trim so save yours for reuse. There are three versions of this glass. The clear version is just that

Complete five piece window glass set for the 1971

Complete five piece window glass set for the 1971

Complete five piece window glass set for the 1971

Good used original door window regulator. Driver side with manual window crank

Good used original door window regulator. Passenger side with manual window crank

383278-S Nut with spinning or captured washer, sometimes called a swivel nut, for attaching various door window components for 1970-1973 Cougar and Mustang bolt-in door glass. This nut was used to fasten the guides into the 1970 bolt in glass. Additionally this nut was used for attaching the window channel bracket to door and quarter glass on the 1971-73 Cougar and Mustangs.

384356-S Bolt with captured washer. Mounts the two stops and is used to install the channel assembly. Five total bolts per door glass, 10 used per car. Very specific sized captured washer for distributing pressure on the glass.Click on images to enlarge. 1970 similar. ...

D0OZ-6223318-A Used 1971-73 Mercury Cougar and Ford Mustang spring for the door window regulators. Same spring used on both power window regulators and manual window regulators.*Caution - These springs have an enormous amount of stored mechanical energy when installed

Round plastic window stop that attaches to the front and rear door window glass on all 1971-73 Mercury Cougar and Ford Mustangs. Two per door

D1ZZ-223A58-A Lower door guide insert to prevent rattling of the window. Two of these inserts are inserted into the lower door guide after the door glass run is installed. Plastic piece that is subject to cracking. Two needed per door, item sold individually.Click on images to enlarge. ...

D1ZZ-6521546-B Used metal door run for all 1971-73 Mercury Cougar and Ford Mustangs. These years only used a single door run on each door. These are not side specific as in prior years. Fits either the passenger or driver side doors. During installation lube with white grease.

D1ZZ-6521760-A Upper door glass window stop. There are two of these that bolt inside the door. These are the 'up' position stops for those round stops that mount to the glass. Item sold individually

D1ZZ-6521790-A Lower window stop for the door glass on 1971-73 Mercury Cougar and Ford Mustang. Just one of these stops per door. These have one end coated with a rubberized plastic as a cushion.

D1ZZ-65222A92-B Lower guide

D1ZZ-6522362-A Upper guide

Original stereo radio pigtail and plug. From a 1972-73 Mercury Cougar or Ford Mustang stereo harness. Has correct plug, wire colors and makings for the plug that connects to the factory stereo radio  *Note This is the speaker radio lead, from the speaker harness.

Used under dash wiring harness repair plug and pigtail to the turn signal switch for the 1971-72 Mercury Cougar, standard or XR7 model. This is part of the 14401 main under dash wiring harness. This plug is the same for Mustang and has the same wiring, the difference is that Mustang is wired different under the dash.*NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's and is the...

Used brake switch plug end, the one that plugs into the brake pedal switch for the brake lights. These often times get hot and partially melt. Easy to change, no cutting or splicing of wires. The female spade plug end just releases from the plug end, look for the release tab for beside the wire on the back.

New wiring pigtail with male bullet connector, and male / female paired connector. Also has rubber grommet that fits a 5/8" inch hole. Looks like 18 gauge wiring. These are remnants from the reproduction Mustang front turn signal lights that we convert to Cougar wiring. Brand new, approximately 13-15 inches in total length. Colors as shown.

Application all 1967-1968 289/302 engines with C4. 1967-1973 small block V-8 with 3 or 4 speed manual transmissions. Features 28 splines. Some have a casting number of C5AW-4888-A.Excludes Hi-performance V-8's such as Boss 302, 390, 428CJ, and C-6 / FMX transmissions.

Replaces Ford Part # C1AZ-4529-A Sold individually. All applications, attaches the drive shaft U-Joint to rear end pinion yoke. 5/16 Inch Diameter #24 thread for 1 1/8 inch Bearing Caps.

Reproduction universal joint that fits the transmission end of the drive axle on the Mercury Cougars and Ford Mustangs equipped with the 289, 302, 351 Windsor and most 351 Clevelands (see chart). this unit includes a grease fitting for an extended life. Replaces Ford part # C3AZ-4635-C or C3AZ-4635-E. *NOTE* Part number C3AZ-4635-C was discontinued in 1968 and was replaced by C3AZ-4635-E.

This reproduction universal joint is forged from high strength alloy steel that is crossed w/ an anti-corrosion coating. This unit also features a grease fitting for an extended life, and fits Mercury Cougars and Ford Mustangs equipped with the 289, 302, 351 Windsor and most 351 Clevelands (see chart). Part number C3AZ-4635-C was discontinued in 1968 and was replaced by C3AZ-4635-E. Span 3.30" cups 1.00" and 1.00"  Replaces Ford part # C3AZ-4635-C or C3AZ-4635-E. *NOTE* Part number...

Used passenger side (right hand) grade "A" clear door glass for the Mercury Cougar or Ford Mustang coupe or convertible equipped with power windows. This unit will not have the faint green tint like the SUN-X factory tinted glass. Very good used door glass with no deep scratches (multiple faint scratches and water spots often will be present). Not perfect but the best you could expect to find from a 50 year old plus parts car and will of course be a better fit than repro.Ford part #...

Used driver side (left hand) grade "B" clear door glass for the Mercury Cougar or Ford Mustang coupe or convertible equipped with manually operated windows. It will not have the faint green tint like the SUN-X factory tinted glass. Good used door glass with minor vertical scratches due to hardened belt line rubber seal and debris caught within the belt line seal. Ford part # D1ZZ-6521411-A.  *NOT* Air conditioning cars were supposed to have SUN-X tinted glass. Look for the SUN-X logo in...

Used passenger side (right hand) grade "B" clear door glass for the Mercury Cougar or Ford Mustang coupe or convertible equipped with manually operated windows. This unit will not have the faint green tint like the SUN-X factory tinted glass. Good used door glass with minor vertical scratches due to hardened belt line rubber seal and debris caught within the belt line seal. Ford part # D1ZZ-6521410-A.  *NOTE* Air conditioning cars were supposed to have SUN-X tinted glass. Look for the...

Door window glass grommet or washer to protect the glass for the Mercury Cougar or Ford Mustang. These units are placed under the bolts for mounting the window stops and the channel bracket. Used on most full and mid sized Ford

1971 - 1973 Mercury Cougar and Ford Mustang coupe / convertible Grade A factory tinted glass for the passenger side door

D1ZZ-6522380-B Used stabilizer that attaches to the top of the door in two different places. These have a fuzzy padded piece that keeps the glass from rattling while it goes up and down on the door run. In most cases

Reproduction quarter window roller for the 71 - 73 Cougar or Mustang. These rollers attach to the window channel bracket and slide up and down through the window guide.Sold individually

Reproduction Guide Anti-Rattle set for the 71 - 73 Cougar or Mustang. Once the door glass run is installed

383278-S 1/4-20 Nut with spinning or captured washer, sometimes called a swivel nut, for attaching various door window components for 1970-1973 Cougar and Mustang bolt-in door glass. This nut was used to fasten the guides into the 1970 bolt in glass. Additionally this nut was used for attaching the window channel bracket to door and quarter glass on the 1971-73 Cougar and Mustangs. This is a new or reproduction part from AMK.

This gear was used on Cougars starting in 1969 and then Mustang in 1971. Fits pretty much every (common) Ford power window motor except for the unique "pancake" style motors found with the 1/4 windows on the Cougar and Mustang. Includes metal plate as shown. Replaces Ford part # D0AZ-62234A24. Do you have questions about Glue-In vs Bolt-In glass? How about how to properly install Glue-In glass in your 1969 Cougar or Mustang? Check out our video below for some great glassy information! 1969...

Shoulder harness bolt cover. This also holds seat belt buckle when it is not in use. Fits Left Hand or Right Hand side of the car. 2 required per car, sold individually. Below are some examples of originals in cars from our wrecking yard: ...

This never came on a Cougar, but it is a nice upgrade from the string that attaches your seat belt shoulder strap to the coat hanger when the shoulder strap is not in use. Fits all models except convertible. Originally, the shoulder strap connected to the bolt cover on one end, And to a string on the shoulder strap that connects it to the coat hook to keep it out of the way when not in use. This new hook slides into the track on the back of the moulding over the door, and is used instead of...

Great looking replacement style seat belts. All feature a mid sixties period look which includes a chrome buckle. Available in a variety of colors. Sold individually

Great looking replacement style seat belts. All feature a mid sixties period look which includes a chrome buckle. Available in a variety of colorssold individually

Great looking replacement style seat belts. All feature a mid sixties period look which includes a chrome buckle. Available in a variety of colors.sold individually

Great looking replacement style seat belts. All feature a mid sixties period look which includes a chrome buckle. Available in a variety of colors.sold individually

Great looking replacement style seat belts. All feature a mid sixties period look which includes a chrome buckle. Available in a variety of colors.sold individually

Great looking replacement style seat belts. All feature a mid sixties period look which includes a chrome buckle. Available in a variety of colors.sold individually

Great looking replacement style seat belts. All feature a mid sixties period look which includes a chrome buckle. Available in a variety of colors.sold individually

Great looking replacement style seat belts. All feature a mid sixties period look which includes a chrome buckle. Available in a variety of colors. Please note: this is the only aftermarket shade of Aqua, which was only used on the Ford Mustang. Contact us for availibility of good used Cougar correct aqua seat belts.Sold individually

These are era-correct looking seat belts at an affordable price.  These are not Concours reproductions, but have the correct vintage look used by Ford on multiple cars in the Mid to Late 1960's. Starburst Medallion used on the buckle is an exact copy of originals.Sold individually Includes: 1 Complete non-retracting seat belt (includes both male and female side)2 Bolts, nuts, and lock washers

Used steel lateral support brace for Cougars and Mustangs with the 351-2V or 351-4V engines after 4/27/1971. Replaces part # D1AZ-2888-A.

New sealed bearing for installing on your 1968-73 Mercury Cougar or Ford Mustang idler / tensioner pulley. This bearing also came in all of the "service replacement" idler pulley assemblies and is physically larger than the idler bearing for the 1968-69 only idler pulley (68-69 bearing sku: 10827). The center portion of the pulley, where this bearing would press into, has an inside diameter measurement of 1 9/16". On the smaller bearing pulley, this measurement is 1 3/8". Both versions of this...

Reproduction stud and nut assembly that the factory line workers used for locating the air conditioning pedestal bracket. Then backed up with a nut. Used on 289 / 302 / 351W / 390 / 428CJ pedestals from 1967 - 1973. Stud is threaded into the cylinder head for easy installation of the cast iron pedestal bracket.*Note - Excludes 351C and 429CJ.

Air conditioning bearing replacement service. Send your flat bearing style, fixed or adjustable A/C pulley and we will exchange it or rebuild your exact pulley with a new flat bearing. Either large or small flat bearings, same price.  Dust caps hand fitted, for seamless installation. No extra tool marks, other than the factory peening. Check photos.Ford casting #'s D0AA-8A617-B, D0AZ-8678-D, C8AZ-8678-B, C8AZ-8678-C, C8AZ-8678-A, D8OH-19W653-A, D0AZ-8678-D.*Note* All new bearings will...

Air conditioning belt tensioning pulley with new bearing. This adjustable bracket and pulley was used on all 1970-73 351 engines that came with A/C, as well as 1970 428CJ & 1971 429CJ. This part often has a casting number of D0AA-8A617-C1 but not always. This adjustable idler pulley is identified by having the large bearing pulley. Same as the C8AZ-8678-A adjustable idler pulley only with a small bearing pulley. We also offer a bearing replacement service to rebuild your adjustable idler...

Stud that the factory line workers used for locating the air conditioning pedestal bracket. Then backed up with a nut. Used on 351C / 429CJ pedestals from 1970 - 1973.*Note - Excludes 289 / 302 / 351W / 390 / 428CJ engines.