Home > 1973 Mercury Cougar
All Available Parts - 1973 Mercury Cougar
Products (Click sub-categories above to ONLY display results for that Sub-Category) 501-600 of 3315
Sorted By:
Availability:
Display Options:
Availability: Out of Stock
Item #: 31542 -
Used hot water tube connector, Grade B condition. Fits 1973 Mercury Cougar and Ford Mustang with EGR valve attached to the carburetor spacer plate. "H" shaped water tube connector with fitting for vacuum thermal valve that controls the EGR valve. These are seldom seen in any condition, Grade B used will have some rust through on the tubes, will be strong enough to slide heater hoses over what is left of the barb. Vacuum thermal switch switch not included. We also have a worse condition Grade C...
Availability: Used / Wrecking Yard Item
Item #: 31541 -
Used hot water tube connector, Grade C condition. Fits 1973 Mercury Cougar and Ford Mustang with EGR valve attached to the carburetor spacer plate. "H" shaped water tube connector with fitting for vacuum thermal valve that controls the EGR valve. These are seldom seen in any condition, Grade C used will have rust through in and on the tube ends. Probably want to get some tubing to fit the inside of the connector tubes, in order to clamp down heater hoses. Vacuum thermal switch switch not...
Availability: In-Stock Item
Item #: 31594 -
Clips or clamps for attaching the 3/8" hard fuel lines to the body of any 1968-73 Mercury Cougar or Ford Mustang. Clips only, save your attaching body bolts. Sold in packages of 4 clips as shown. Will work on 1967 cars if you change to 3/8 lines. 1971-73 Cougar owners can use item 27565 attaching bolts, they are the same as the fuel tank mounting bolts. See related items. Replaces Ford 354663-S8
Availability: In-Stock Item
Item #: 53205 -
New flat nut, these attach both the shifter seal and shifter dial to the under side of the automatic shifter bezel. Check out our video on rebuilding your shifter below: ...
Availability: In-Stock Item
Item #: 25990 -
Reproduction Firewall Insulation Pad Clip Kit for the 1967 - 1973 Mercury Cougar / Ford Mustang
Availability: In-Stock Item
Item #: 26050 -
Reproduction thin firewall insulation pad with clips for the Mercury Cougar or Ford Mustang. This unit will fit both the A/C and non A/C Cougar or Mustang.
Availability: Used / Wrecking Yard Item
Item #: 25319 -
Grade "B" part that will have only one of the four mounting tabs broken or cracked. Select a color and we will attempt to accommodate you.
Availability: Used / Wrecking Yard Item
Item #: 25318 -
Grade 'A' part that will have none of the four mounting tabs broken or cracked. Enter your preferred color in the order notes at checkout and we will attempt to accommodate you.
Availability: In-Stock Item
Item #: 15840 -
Replacement throttle pedal spring for your 71 - 73 Cougar or Mustang. Easy to replace, keeps correct tension on your gas pedal.
Availability: In-Stock Item
Item #: 30166 -
Screw for attaching steering column plate to floor board. Usually 4 are needed and go through the carpet and into the toe board. Correct finish and style of AMK bolt. Length 1 3/16"#14 Threads
Availability: Used / Wrecking Yard Item
Item #: 31496 -
Used driver side interior kick panel for any 1971-73 Mercury Cougar. Ford calls this item a "Panel - Cowl Trim". These came in a variety of different colors, please indicate a desired color in the notes. Plan on painting the panel with a quality vinyl paint such as those made by SEM for a quality installation. These are used, and will likely show some scuffing from hard shoes. Ford part number D1WB-6502344, D2WB-6502344, D3WB-6502344. ...
Availability: Used / Wrecking Yard Item
Item #: 31495 -
Used driver side interior kick panel for any 1971-73 Mercury Cougar. Ford calls this item a "Panel - Cowl Trim". These came in a variety of different colors, please indicate a desired color in the notes. Plan on painting the panel with a quality vinyl paint such as those made by SEM for a quality installation. These are used, and will likely show some scuffing from hard shoes. Ford part numbers D1WB-6502345, D2WB-6502345, D3WB-6502345.
Availability: Used / Wrecking Yard Item
Item #: 21-1037 -
Used Oil pressure gauge, Amp meter gauge, housing assembly for all 1971-73 Mercury Cougar XR7. This is the two gauge pod found in the center of the dash panels. We only sell these as assemblies, lens sold separately. Ford part numbers found on this part are D1WF-10848 & D1WF-10894. Check out the video below on our new gauge tester: ...
Availability: Used / Wrecking Yard Item
Item #: 32181 -
Good used console clock surround bezel with no cracks, or peeling chrome. Engineering number on the backside reads D1ZB-15017-AA
Availability: Used / Wrecking Yard Item
Item #: 32916 -
Used metal dash support brace for all 1971-73 Mercury Cougar and Ford Mustangs. Fastens to the lower flange of the metal dash panel and attaches to the inner cowl, 10 inches long. Replaces Ford part numbers D1ZB-6504672-A.
Availability: Used / Wrecking Yard Item
Item #: 25382 -
Don't be fooled by knobs with similar part numbers, they have longer shafts and will not work as well on your Mercury Cougar or Ford Mustang application.Ford part # D1ZZ-18830-A, and Ford casting # D1ZA-18A932-AA.*TRIVIA* Did you know that Ford called the inner (balance / tone) radio knobs "discs?"
Availability: In-Stock Item
Item #: 15703 -
Finally, a reproduction radio knob set for your 1971-73 Mercury Cougar or Ford Mustang! These little units are very hard to find in NOS form or good used condition with flawless chrome. Most knobs are peeling bad enough to cut you if you are not being cautious. It's often little detail pieces like these that separate first and second place at car shows.Replaces Ford part #'s D1ZZ-18817-A for the outer (tuner / volume) knob, Ford casting # D1ZA-18822-AA for the outer (tuner / volume) knob....
Availability: Out of Stock
Item #: 26213 -
This kit is similar to the original type mounted in every drivers side door. These OEM style Riv-Nuts will be a challenge to install unless you have the special tool. Almost every body shop will have this rivet gun type of tool but here are a couple of ways to tackle the installation without the correct tool. Hole size is 1/4". Replaces Ford Part #: C7AZ-17696. Check out our video below for more info on mirror installation: Still have riv-nut questions? Here are riv-nut answers! ...
Availability: In-Stock Item
Item #: 10244 -
New mirror glass, for the passenger side on practically any 1969-73 Ford with painted sport mirrors. This is the convex style of mirror, think "Objects in mirror are closer than they appear". Nice fit, exact shape of originals. Dimensions: 4 3/8 x 2 7/8 Do you have questions about installing a passenger side mirror or using Riv-Nuts? Have more questions about installing a passenger side mirror or using Riv-Nuts? Got a mirror lens that flops around in your Sport Mirror every time you hit a tiny...
Availability: In-Stock Item
Item #: 12029 -
Pair of reproduction brackets and rods for the sun visors in the Mercury Cougar or Ford Mustang. *NOTE* These units will also work for the 1971-73 Ford Mustang fastback (sport roof).
Availability: Used / Wrecking Yard Item
Item #: 30483 -
This knurled nut is located under the front slides in each corner (1 per side, 2 per car) and is used to adjust the height of the sun roof panel.
Availability: Used / Wrecking Yard Item
Item #: 30486 -
Curved aluminum cable guide as seen on page 13 of the sun roof manual. Golde part number 100 413 682
Availability: Used / Wrecking Yard Item
Item #: 30674 -
Curved aluminum cable guide as seen on page 13 of the sun roof manual. Golde part number 100 413 681
Availability: Used / Wrecking Yard Item
Item #: 30676 -
Front guide that measures 10 5/8" long held in place by four screws. The driver side has no markings but the passenger side is stamped with an R and the inner 2 screw holes are in a different place than the driver.
Availability: Used / Wrecking Yard Item
Item #: 30675 -
Front guide that measures 10 5/8" long held in place by four screws. The driver side has no markings but the passenger side is stamped with an R and the inner 2 screw holes are in a different place than the passenger.
Availability: Used / Wrecking Yard Item
Item #: 30677 -
Guide that measures 10 5/8" long held in place by the outer trim that has four screws. Driver and Passenger are interchangeable.
Availability: Used / Wrecking Yard Item
Item #: 30678 -
This part mates to and is held down by Golde #100 413 682. The Golde part number for the smaller, lower elbow guide is 100 413 663
Availability: Used / Wrecking Yard Item
Item #: 30679 -
This part mates to and is held down by Golde #100 413 681. The Golde part number for the smaller, lower elbow guide is 100 413 664
Availability: Used / Wrecking Yard Item
Item #: 32915 -
This strip has a series of five retaining clips that hold the headlining panel to the roof panels as seen on page 14 of the sun roof manual.This is for the 1971-73 Mercury Cougar with factory sunroof. Sunroof measurements are roughly 19-1/2 x 39 inches. This panel is 32-1/4 inches long with 5 clips as shown.
Availability: Used / Wrecking Yard Item
Item #: 15-0401 -
Reproduction wrench or crank, for manually closing the factory installed sunroof installed on any 1967-73 Mercury Cougar. Sunroofs, technically moonroofs, were originally installed by ASC or American Sunroof Corporation. Hertz 1968 XR7-G cars all came with factory sunroofs, as did the Hertz rental 1969-70 Cougar Eliminators. ASC also installed sunroofs in Ford Thunderbird, Lincoln MK III.ASC used Golde mechanical parts from Germany. Golde was a manufacturer of sliding canvas and metal roofs on...
Availability: Used / Wrecking Yard Item
Item #: 30480 -
This strip has a series of seven retaining clips that hold the headlining panel to the roof panels as seen on page 14 of the sun roof manual.
Availability: Used / Wrecking Yard Item
Item #: 30481 -
This part is located in the right front corner of the panel and has to be rotated inward to remove it from the guide rail so the panel cannot be removed. Imprinted on the plastic portion of the part is a Golde part number 100 414 645. Ford part number C8WY-65502L08-A
Availability: In-Stock Item
Item #: 11822 -
12-point bolt for attaching the steering column coupler to the steering box. Works for all 1967-73 Mercury Cougars and most other Fords, Mercury, and Lincolns. One bolt used for fixed columns, two bolts used on tilt steering columns. Sold individually.
Availability: In-Stock Item
Item #: 27601 -
Reproduction insulator for the lower portion of the steering column found on all 1969-73 Mercury Cougar or Ford Mustangs. Unique slide in plastic bushing or insulator, which slides into the bottom tube of both fixed and tilt columns. Most originals are broken or missing. Two sizes of insulators, please verify year and diameter.1968 tube measures 1 3/8"1969 - 1973 tube measures 1 5/8"*NOTE* WCCC services all FoMoCo tilt and tilt-tilt away steering columns 1967-1979. Our shop rate for this...
Availability: Used / Wrecking Yard Item
Item #: 15-0146 -
Used Release Spring for the 1967 - 1973 Mercury Cougar / 1967 - 1973 Ford Mustang
Availability: Used / Wrecking Yard Item
Item #: 15-0145 -
Used Spring Sleeve Cap for the 1967 - 1973 Mercury Cougar / 1967 - 1973 Ford Mustang
Availability: In-Stock Item
Item #: 26181 -
For fixed steering wheel. Special molded rubber sleeve that holds the bearing in place. Exact reproduction. Replaces Ford part # D1AZ-3518 or E2AZ-3518
Availability: Out of Stock
Item #: 15-0083 -
Used plunger spring used in the bale of the tilt / tilt away steering column found in the Mercury Cougar or Ford Mustang. Small plunger spring for 1967-69 tilt columns. Maintains pressure on the heavy wire tilt release bale. This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit of 50% of our web price for parts delivered in hand or by carrier to our Brooks, Oregon location. If you're not...
Availability: Used / Wrecking Yard Item
Item #: 15-0151 -
This is the brass piece that connects the keylock to the ignition switch.
Availability: Used / Wrecking Yard Item
Item #: 15-0181 -
This is a complete shaft. Lower, upper and knuckle. This shaft may have plastic pins broken due to age and handling. It is functional. May have light rust and knuckle will have been tightened if needed.
Availability: Used / Wrecking Yard Item
Item #: 15-0190 -
Used lower steering column shaft for 70 - 73 Cougars and Mustangs with a fixed column. Identified by length, and the round style lower flange. 1968-69 lower flange is slightly smaller with flat sides. Overall length is 16-3/8 inches.
Availability: In-Stock Item
Item #: 32897 -
Used sleeve for fixed steering wheel. Special molded rubber sleeve that holds the bearing in place. Ford part # D1AZ-3518 or E2AZ-3518
Availability: Used / Wrecking Yard Item
Item #: 33445 -
Used lateral or side bracket for mounting the steering column to the instrument panel on any 1972-73 Mercury Cougar or Ford Mustang. Hooped support bracket only, there is also a large main bracket that is also needed. Tilt and fixed steering columns. Bracket also used on 1971 full sized Ford and Mercury cars. Ford part number D1AZ-3B139-A.
Availability: Used / Wrecking Yard Item
Item #: 33446 -
Used bracket for mounting the steering column to the instrument panel on any 1972-73 Mercury Cougar or Ford Mustang. Main bracket only, there is also a hooped support bracket that is also needed. Tilt and fixed steering columns. Bracket also used on 1971 full sized Ford and Mercury cars. Ford part number D1AZ-3676-A.
Availability: Used / Wrecking Yard Item
Item #: 33447 -
Used wiring harness retainer bracket for mounting the steering column bracket, on any 1973 Mercury Cougar or Ford Mustang. Retainer only, many of these are missing. Probably not missed, limited to stock on hand. Basic Ford part number 14A163.
Availability: Used / Wrecking Yard Item
Item #: 33450 -
Used flat headed stove bolt and nut, for attaching the two steering column mounting brackets together. Brackets for mounting the steering column to the instrument panel on any 1972-73 Mercury Cougar or Ford Mustang. Two needed per installation, sold individually. This is a 3/8-16 square neck bolt and nut. Ford part number 384527-S2.
Availability: Used / Wrecking Yard Item
Item #: 33452 -
Used lower steering column mounting bracket at firewall, for any 1971-73 Mercury Cougar or Ford Mustang. Rubber seal will need to be replaced, see related items for rubber seal. Ford part number D1ZZ-65017A50-A.
Availability: Used / Wrecking Yard Item
Item #: 15-0028 -
Correct nut that is designed not to come undone.
Availability: In-Stock Item
Item #: 41886 -
Reproduction drum brake pedal pad for the Mercury Cougar or Ford Mustang equipped with an automatic transmission. The 1967 version of this piece is narrower than this 1968-73 piece.Replaces Ford part # C6OZ-2457-A.
Availability: In-Stock Item
Item #: 42136 -
These reproduction brake and clutch pedal bushings are made from high strength plastic that is wear resistant. Two are required for automatic cars, four for manual transmission cars. Sold as a pair. Replaces Ford part # B7AZ-2471-A.
Availability: Used / Wrecking Yard Item
Item #: 27269 -
Used standard grade "B" main under hood wiring harness located in the engine compartment. This harness has plugs for the head lights, voltage regulator, starter solenoid, windshield washer pump, and horns. All electrical harnesses are inspected, professionally repaired, tested, and ready to install. Grade "B" harnesses may have one or two repairs as where grade "A" harnesses will be rare uncut beauties. 1973 Mercury Cougar Standard models only with AMP warning light. Not compatible with XR7...
Availability: In-Stock Item
Item #: 41433 -
3/4" wide and 60' long. This tape resembles the tape you would find on bicycle handle bars or a hockey stick but is in fact different. The taillight harness uses this type of tape as well as portions of the under dash harness. Not used in modern applications and getting rather hard to find these days.NOTE: This is FRICTION tape not adhesive tape. It is coated with rubber and relies on friction with itself to wrap wires. It does not stick to the wires. This was one of the first types of...
Availability: Used / Wrecking Yard Item
Item #: 11214 -
Wiring pigtail for the low fuel sending units on 1973 Mercury Cougar XR7 and standard models with low fuel warning light, cut from a taillight wiring harness. The wiring is all integrated in 1973, unlike 1971-72 which has a separate harness for the fuel sending unit. The Safety Convenience Package included a low fuel warning light. This pigtail has three wires which attaches to the three prongs on the D1WF-9275-AC low fuel sending units. Ford part number is D3WB-14406-B or D3WY-14406-B. *Note...
Availability: Out of Stock
Item #: 25580 -
Used Standard Grade A Taillight Wiring Harness for the 1973 Mercury Cougar
Availability: Out of Stock
Item #: 26952 -
Used Standard Grade B Taillight Wiring Harness for the 1973 Mercury Cougar
Availability: In-Stock Item
Item #: 33129 -
Used XR7 Taillight Wiring Harness for the 1973 Mercury Cougar
Availability: Discontinued
Item #: 27246 -
Used grade "A" under dash wiring harness and fuse panel / block for the Mercury Cougar standard and standard convertible. This very clean uncut harness is not corroded on the connections or brittle from heat and is tested and ready to install.*NOTE* If you send us your old used under dash harness, you will receive an in store credit of up to $100. Also keep in mind that we buy original under dash harnesses. We are interested in all under dash harnesses, but are primarily interested in the XR7...
Availability: Used / Wrecking Yard Item
Item #: 30079 -
Used under dash harness repair plug and pigtail for the light switch harness for the Mercury Cougar Standard and XR7. This is part of the 14401 main under dash wiring harness.*NOTE* The individual wires can be removed from the block and other wires can be inserted if your car has different options.
Availability: Used / Wrecking Yard Item
Item #: 25070 -
Alternator spacer bracket for all 351 engines. 1970-73 Mercury Cougar and Ford Mustang among others such as Torino, Cyclone, Galaxie, LTD, etc. Aluminum material, 2-1/4 inches long, with a 7/16" hole. Sometimes solid and sometimes open along the side. Ford part number D0OZ-10A370-A.
Availability: Used / Wrecking Yard Item
Item #: 25037 -
Used alternator mounting bracket for any 1970-73 Mercury Cougar, Ford or Ford Mustang with 302, 351W, or 351C engines. Replaces Ford part number D0OE-10156-A.
Availability: Used / Wrecking Yard Item
Item #: 25035 -
Used alternator adjusting arm for any 1970-73 Mercury Cougar, Ford Mustang, or generally Ford anything with 302, 351, or Boss 302 engines. This can be used on 1973 cars, Ford did switch to a different alternator bracket that tightened the alternator from the back sometime in 1973. Replaces Ford part number D0OE-10145-A, listed in the Motorcraft catalog as GY-938Also fits:Comet Montego
Availability: Used / Wrecking Yard Item
Item #: 25553 -
Ford started using this alternator adjusting bracket sometime in 1973. It mounts to the rear of the alternator. Fits any 1973 Mercury Cougar and Ford Mustang and likely many other Ford cars with 351 engines. It works with the 1970-73 front mounting bracket. Replaces Ford part number D3AE-10145-C.
Availability: Used / Wrecking Yard Item
Item #: 25439 -
Factory original part for all 1971 - 1973 Cougar *convertibles. Also correct for 1971 429CJ all body styles. Right hand bracket. Ford part number D1ZZ-6028-A.Does not come with hardware. May have a single or pair of holes on the flat surface. We see them both ways.*Excludes non-convertible models.
Availability: Used / Wrecking Yard Item
Item #: 25440 -
Factory original part for all 1971 - 1973 Cougar *convertibles. Also correct for 1971 429CJ all body styles. Left hand bracket. Ford part number D1ZZ-6029-A. May have a single or pair of holes on the flat surface. We see them both ways.*Excludes non-convertible models.
Availability: In-Stock Item
Item #: 41352 -
Sold individually
# 56354-S
Availability: Used / Wrecking Yard Item
Item #: 25013 -
D0AZ-3A732-C Stamped steel bracket for mounting the power steering pump. Ford called this bracket the 'power steering pump adjusting bracket'. For any factory air conditioned or non-air conditioned 1971 - 1973 Cougar or Mustang with 351 engines, additionally used on Mustangs with the F code 302 V8 engines.
Availability: Used / Wrecking Yard Item
Item #: 31118 -
Used power steering oil cooler for many 1971-73 Ford, Lincoln and Mercury cars with air conditioning. Specifically these came from 1971-73 Mercury Cougar or Ford Mustangs with factory installed air conditioning and power steering. This unit mounts to the top of the A/C compressor. This installs inline with the low pressure return hose. Manufactured by the Blissfield Company and has a Ford stamped number of D1AA-3D746-AB. The Ford engineering number is D1AZ-3D746-D.
Availability: Used / Wrecking Yard Item
Item #: 26784 -
Sold as a pair. One long and one short bracket. Fits 1971-73 Mercury Cougar and Ford Mustangs that have original style radiators. Mounting bolts not included. Replaces Ford part number D0OB-8B359 RH, and D0AB-8K007 LH. Check out our video on Radiator and Fan upgrades below: ...
Availability: Used / Wrecking Yard Item
Item #: 23904 -
C6AE-E Multiple applications over the years. 1. Later 1967 production cooling fan, generally used after 11/14/1966 on most 289 engine applications. 2. 1968 302 without air conditioning. 3. Mid year (after 11/6/1968) 1969 351 without air conditioning. 4. 1969 Early Boss 302 before 4/14/1969. 5. 1971 Cougar with 351 engine, without air conditioning. 6. **1973 Cougar 351-2V without air conditioning prior to 2/19/1973. Fan description - 4 blades and 17-1/2 inches in diameter. Ford master part...
Availability: Used / Wrecking Yard Item
Item #: 25505 -
D2OE-AB Applications: 1. 1972 Cougar with H code 351-2V engines - without air conditioning. 2. 1973 Cougar with H code 351-2V engine after 2/19/1973 - without air conditioning. May also be marked D2OE-AA. Fan description - 4 blades and 18-1/2 inches in diameter. Ford master part number D2OZ-8600-A. Check out this interesting video where they test the efficiency of factory style and aftermarket fans. Spoiler alert: the clutch fans are the most efficient! ...
Availability: Used / Wrecking Yard Item
Item #: 25504 -
D2OE-AA Applications: 1. 1972 Cougar with H code 351-2V engines - without air conditioning. 2. 1973 Cougar with H code 351-2V engine after 2/19/1973 - without air conditioning. May also be marked D2OE-AB. Fan description - 4 blades and 18-1/2 inches in diameter. Ford master part number D2OZ-8600-A. Check out this interesting video where they test the efficiency of factory style and aftermarket fans. Spoiler alert: the clutch fans are the most efficient! ...
Availability: Used / Wrecking Yard Item
Item #: 25593 -
D3ZE-8146-AB Original used fan shroud with a 1973 casting number. Should be for all V-8 engines with air conditioning. Good used, this exact 1973 shroud is not reproduced. For some helpful tips on upgrading your Cougar (or Mustang) cooling system, check out our video:
Availability: In-Stock Item
Item #: 19916 -
This is an excellent reproduction made from the original Ford tooling and features the original Ford logo. This is correct for all the cross flow radiators used in 1971 - 1973 except the 1971 429CJ. Opening measures about 20-1/8" in diameter. Replaces Ford part # D1ZZ-8146. For some helpful tips on upgrading your Cougar (or Mustang) cooling system, check out our video: ...
Availability: In-Stock Item
Item #: 53256 -
Fan shroud hardware kit for the 302 or 351 on the 1971, 1972 or 1973 Cougar and Mustang.
Availability: In-Stock Item
Item #: 14192 -
These concours quality Zinc caps are made in America and bear all the original markings. O.E.M. details include original letter style, "S.M.C.O." and "Autolite". Pound rating is stamped on cap.
Availability: In-Stock Item
Item #: 14171 -
These concours quality Chrome caps are made in America and bear all the original markings. O.E.M. details include original letter style, "S.M.C.O." and "Autolite". Pound rating is stamped on cap.
Availability: Out of Stock
Item #: 14018 -
These are O.E.M. replacements and will not fit most after market radiators.
Availability: In-Stock Item
Item #: 14014 -
Keeps the corrosive agent in your coolant from destroying vital engine components
Availability: In-Stock Item
Item #: 11810 -
Replacement radiator cap for the 1967 - 1973 Mercury Cougar or 1967 - 1973 Ford Mustang. This radiator cap releases pressure when the pressure exceeds 13 pound of pressure.
Availability: In-Stock Item
Item #: 14230 -
New 13 Pound Generic Radiator Cap with Safety Release for the 1967 - 1973 Mercury Cougar / Ford Mustang
Availability: Ships Direct from Supplier (Except International)
Item #: 14735 -
Usually ships in 3-5 business days. Reproduction direct fit OE style 3 row MaxCore radiator, designed for optimal performance with increased tube size and amount of fins. Our supplier uses higher copper purity for long lasting durability and heat transfer.
Availability: Out of Stock
Item #: 15806 -
All steel fitting for the lower radiator tank, found on all cars with automatic transmissions. The fine threads go to the radiator and the transmission cooling line screws onto the flared fitting after installation into the radiator. Two needed per car, sold individually. Fits all years 1967-73, and all automatic transmissions. 1/2" threads go to cooling lines. 3/8" threads go into the radiator. *Note - This is an original steel fitting, not a brass reproduction. ...
Availability: Discontinued
Item #: 26962 -
Used grade "B" under dash wiring harness and fuse panel / block for the Mercury Cougar standard and standard convertible. This harness may have one or two professional repairs, it is tested and ready to install.*NOTE* If you send us your old used under dash harness, you will receive an in store credit of up to $100. Also keep in mind that we buy original under dash harnesses. We are interested in all under dash harnesses, but are primarily interested in the XR7 harness.Ford part # D3WY-14401. ...
Availability: Used / Wrecking Yard Item
Item #: 27534 -
Factory original part for all 1973 Cougar hardtops with 351 engines. 1973 Mustang with 302 or 351 engines. Right hand bracket. Ford part number D3ZZ-6028. Does not come with mounting hardware. *Note - rubber mounts are not available new for these 1973 engine mounts. Save your old ones!*Excludes convertible models.
Availability: Used / Wrecking Yard Item
Item #: 27567 -
Engine mount for all 1973 V-8 engines in 1973 Mercury Cougar and Ford Mustang coupe body styles only. 1973 only, and these only work with hardtop or coupe engine frame stands. We occasionally have these in good used condition, normally only one side is broken or worn. In the long run we recommend converting to 1971-72 coupe engine stands and mounts. This requires replacing BOTH the 1973 coupe engine frame stands as well as the engine mounts with the 1971 - 1972 coupe version.Sold...
Availability: In-Stock Item
Item #: 32161 -
Engine mount bolt kit for installing engine or motor mounts to the frame stands. 1971-73 Mercury Cougar or Ford Mustang V-8. Two bolts and two nuts. Quality AMK part F-467.
Availability: In-Stock Item
Item #: 30756 -
Reproduction overflow hose with smooth outer wall. Hose length 36"
Availability: In-Stock Item
Item #: 14334 -
Fits all* Ford V-8 engines, 1967 - 1973. *- NOTE: This will fit in the 351C, 351M or 400 but will not block off the port to recirculate the water back through the engine. This can cause the engine to run hotter than desired.
Availability: In-Stock Item
Item #: 14332 -
Fits all* Ford V-8 engines, 1967 - 1973. *- NOTE: This will fit in the 351C, 351M or 400 but will not block off the port to recirculate the water back through the engine. This can cause the engine to run hotter than desired.
Availability: In-Stock Item
Item #: 14329 -
Fits all* Ford V-8 engines, 1967 - 1973. *- NOTE: This will fit in the 351C, 351M or 400 but will not block off the port to recirculate the water back through the engine. This can cause the engine to run hotter than desired.
Availability: In-Stock Item
Item #: 25724 -
Adhesive-Backed Gasket Material Helps Prevent Breaking of Water Outlet. Gasket Cement is Not Needed. Self-Adhesive Backing Holds Thermostat in Place While Water Outlet is Being Installed.
Availability: In-Stock Item
Item #: 14330 -
Thermostat Housing Gasket BY FEL-PRO® for the 351 Cleveland.
Availability: Out of Stock
Item #: 14335 -
Thermostat Housing Gasket BY FEL-PRO® Replaces Ford Part #: C5AZ-8255-A.
Availability: In-Stock Item
Item #: 42051 -
This elbow is zinc plated for years of reliable service and is for 351, 390, and 428 engines. Replaces Ford Part #: D0AZ-18599-A.
Availability: Out of Stock
Item #: 12977 -
This fail safe thermostat can save you from costly engine damage during an overheat. They feature an exclusive technology that locks the valve open position if overheating occurs. This allows for maximum coolant flow when you need it most.
Availability: In-Stock Item
Item #: 30465 -
Reproduction water bypass plate for all Ford 351C engines. This is an original style brass restrictor plate for 70-73 Cougar, Mustang, Torino etc.Must be used in conjunction with the correct 180 degree thermostat.For some helpful tips on upgrading your Cougar (or Mustang) cooling system, check out our video: ...
Availability: In-Stock Item
Item #: 30466 -
Reproduction concours correct premium thermostat for the 351C. This is the correct thermostat you would use in conjunction with the new concourse restrictor / by-pass plate on 70 - 73 Cougars and Mustangs equipped with a 351 Cleveland engine. This is a the assembly line style thermostat. Replaces Ford part number D0AE-8575-B.
Availability: In-Stock Item
Item #: 41520 -
OEM replacement water pump for the 351 Cleveland. Gasket included. Replaces Ford Part #: D0AZ-8501-E.
Availability: In-Stock Item
Item #: 41522 -
OEM replacement Water Pump for the 351 Windsor. Gasket included. Replaces Ford Part #: D0OZ-8501-A.
Availability: In-Stock Item
Item #: 10622 -
Water pump gasket for all 289/302/351W/351C/429 engines. This gasket is used between the water pump and water pump plate.