All Available Parts - 1973 Mercury Cougar

This is the rubber spacer / washer that goes between the bolt head and the metal washer of your seat belt hardware. The purpose of the rubber washer is to dampen any vibrations caused by the movement of the seat belt.Sold individually# 354959-S

Sold individually # 374212-S

Concours correct for 67, but a nice dress-up item for 68-73. Replaces Ford Part # 382627 Four bolts, four washers and eight rubber washers in mounting kit.

Engine oil dipstick as found on most any 1970-73 Ford with 351 Cleveland engines (H, or M Code), 1972-73 (Q code). Ford used several different suppliers and there are differences that show up in the finger handle as shown. Top of the shield to the dipstick end is approximately 21-11/16 inches. The handles were painted blue originally. Ford part # D0AZ-6750-A, Ford casting # D0AE-6750-A.*NOTE* In 1970 351W engines also were designated as H codes, 351W has 6 bolts attaching the valve covers,...

Brightens the engine compartment and looks sharp. Fits our big block finned aluminum valve covers (item# 26018) and others with the round push-in style opening. Requires a rubber grommet to fit into the valve cover, which is usually included with new valve covers.Does NOT fit valve covers with the "stovepipe" fitting (like our small block finned aluminum units) or factory valve covers the tabs for twist-on oil caps. This cap is for after market valve covers.

Brightens the engine compartment and looks sharp. Fits aftermarket valve covers only. These require a rubber grommet to fit into the valve cover. Please Note: This oil cap DOES NOT fit the finned "G" valve covers we sale, as they are built to OEM specs.

These spacer / washers were used on the rear belts of 1968 - 1973 Cougars. 1968 used two per bolt for a total of eight, 69-71 used one per rear belt for a total of four and 72-73 used one per belt on the inner only as the outer belts had a re-tractor in the rear 72-73. They were red to guide the line workers on placement.

Bulk pack of 100 oval head phillips screws for door and window crank handles.

These spacer / washers were used on the rear belts of 1968 - 1973 Cougars. 1968 used two per bolt for a total of eight, 69-71 used one per rear belt for a total of four and 72-73 used one per belt on the inner only as the outer belts had a re-tractor in the rear 72-73. They were red to guide the line workers on placement. Sized like the originals, but do not have the dimples all over. 0.53" ID x 0.88" OD.

These brackets are intended to make sure that the brake pads and the caliper stay in the correct alignment, as well as for anti-rattle. Replaces Ford Part # C8OZ-2B295-A. Sold individually

Replaces Ford Part # 382713-S Sold individually

Replaces Ford Part # C8AZ-2066-A Sold individually

Reproduction disc brake caliper insulators for a large array of FoMoCo products starting in 1968. 2 are required per caliper, 4 total per vehicle. Sold as a pair.Replaces Ford part # C8AZ-2B299-A.

Replaces Ford Part # C8AZ-2069-A Sold individually

Replaces Ford Part # 43260-S Sold individually

This nut fits onto the strut brace at the front of the car, and not the control arm end. It is the lock nut that goes on after the the bigger strut rod bushing nut.Replaces Ford part # 340460-S

This clip is the same as a door panel clip with the exception that it does not have the foam spacer. This clip was used on the 1968 XR7 overhead console, 1967 - 1968 xr7 and standard model upper and lower console pads, seat back access panels and several other applications. This original clip holds tighter than the reproduction. We recommend using this used clip over our reproduction for applications like the seat back because the reproductions often do not cut it. Ford part number...

Two or three of these clips were needed per door to mount the padded armrest. Three were used per armrest for a total of six, on 1969-70 Cougar and Mustangs. Two used in 1971-73 on standard Cougars. Sold individually.Replaces Ford part # C6AZ-6224146-B.

Used in multiple applications front and rear lap belts. Inner and outer, marked with a letter "B" in at least three known fonts. 1-3/4 inches long, 1/2 inch shoulder, Torx 50 tool for installation and removal.

Two per car, identified with the letter "D" in three known fonts. This bolt was used in conjunction with a chrome spacer / washer that is also marked with the letter "D". 1-1/2 inches long, 1/4 inch shoulder, use a Torx 50 for installation and removal.

Used on inner and outer rear seat belt bolts, four per car in 1970 -1971 and used only on the inner rears in 72 - 73 due to the addition of rear retractors. Used in conjunction with two red washer / spacers, marked with three known font styles of the letter "A". 1-5/16 inches long, Torx 50 is the tool for installing and removing.

One per side, 1968 does not use the triangle markings. The letter "D" stamping was in place to aid line workers with correct placement on the car.

Often you will see minor irregularities in these washers. These would be considered "blems". Two required per car, used only on the re-tractors.

Replaces Ford Part # 382626-S Sold individually

Two or three of these clips were needed per door to mount the padded armrest. Three were used per car for a total of six, on 1969-70 Cougar and Mustangs. Two used in 1971-73 on standard Cougars. Sold individually.Replaces Ford part # C6AZ-6224146-B.

Reproduction shoulder belt bolt spacer for the 69 - 73 Cougar or Mustang. Does not have markings like the originals. One per side, two per car.

Used single bolt for attaching door and quarter window regulators on any 1969-73 Mercury Cougar or Ford Mustang or Ford anything most likely. Sold individually

New single bolt for attaching door and quarter window regulators on any 1969-73 Mercury Cougar or Ford Mustang or Ford anything most likely. AMK part. Sold individually

Reproduction bolts and washers for the shoulder belts on any 1969-73 Mercury Cougar or Ford Mustang. Includes 2 each of the "D" bolts and chrome thick washers. Quality AMK kit F-3563.

AMK seat belt washer B-13023. 0.46" ID x 1.25" OD zinc flat washer. Sized so that it rides on the shoulder of the seat belt bolts. It allows the retractor to rotate freely between this washer and the head of the seat belt bolt on 1969-73 cars. Two required per car, used only on the re-tractors.

Phosphate & Oil finish. Sold individually. Replaces Ford part #: 378782-S

This is longer of the two with the + on the bolt head.

part# 372821-S

Ford manual transmission flywheel and automatic transmission flex plate mounting bolts. 6 bolts required, sold individually. Replaces Ford part # 378172-S

Replaces Ford part # 55806-S

part # 56131-S

Used on all small block engines to attach the timing pointer to the timing cover. 1967 - 1973 V-8 engines 289, 302, & 351.

Reproduction AC Compressor Clutch Bolt for the 1967 - 1973 Mercury Cougar - 1967 - 1973 Ford MustangSold individually

Reproduction 351W Intake Manifold Bolt for the 1969 - 1973 Mercury Cougar - 1969 - 1973 Ford MustangSold individually 

Reproduction Alternator Pulley Nut for the 1967 - 1973 Mercury Cougar - 1967 - 1973 Ford MustangSold individually 

Replaces Ford part # 351089-S Zinc (dark silver) finish Sold individually

Replaces Part # C9OB-3B284. We also have this bolt available in fine thread but only as a used bolt. Four required per car. Sold individually

part # 370608-S. Used in multiple places on mounting brackets.

This nut fits onto the strut brace at the front of the car, and not the control arm end.Replaces Ford part # 380517-S

part # 383722-S Pivot bolt for use with the all steel 1970-73 power steering pump mounting bracket. NOS new old stock! Fits most all Ford 302/351 from 1970-73 with the above described bracket.

OEM style nut to hold the axle U-bolt to the axle. Fine threaded like originals 7/16-20 grade 5. Will not fit some reproduction U-bolts. Sometimes these are called shock plate bolts. Replaces Ford part # 379244-S

part# 384114-S100 Sold individually

Reproduction adjustment cam / bolt for the lower control arms of the Mercury Cougar or Ford Mustang. We also offer this used version as well. These units are sold individually.Ford part # C6OA-3B236-A.

1/2"-13 x 4 1/2" grade 8 flanged bolt with a phosphate and oil finish.  Ford Part # 382486-S.

replaces Ford part # B-12764

Replaces Ford part #375381-S Phosphate & Oil Finish

Fine thread lock nut used in various places on old Fords, including the differential housing, 1967 disc brake assemblies, and more. Replaces Ford part # 34445-S

Reproduction nut that replaces Ford part # 34033-S. This is the nut that secures the pitman arm to the steering box. Has correct 7/8"-14 threads. Split washer also needed, not included, nut only.

Sold indiviually Phosphate & Oil (gay-black)

Complete engine mounting hardware kit for the 72-73 351C 2-barrel engine. See below for list of included hardware. Click on images to enlarge.

Complete engine mounting hardware kit for the 72-73 351C 4-barrel engine. See below for list of included hardware. Click on images to enlarge.

Sold as a pair. Replaces Ford Part # : D0OZ-8052 Check out our video on Radiator and Fan upgrades below:

New valve cover bolts for all Boss 302, 351C-2V, and 351C-4V Ford engines. These are the AMK bolts with original style Ford assembly line head markings. Correct 7/16 hex head and split tooth captured washer, sold in sets of 16.*Note - Excludes 289/302 and 351W engines (see part  number 8316)1/4-20 X 5/8" Hex Head Bolt with Electrolytic Zinc & Wax finishReplaces Ford part number 373071-S.

Reproduction brake and fuel line clamp kit for Mercury Cougars and Ford mustangs equipped with disc brakes.

Reproduction brake and fuel line clamp kit for Mercury Cougars and Ford Mustangs equipped with drum brakes.

Throttle cable for many 1972 and all 1973 Mercury Cougar and Ford Mustang H code 351-2V engines. Cable length 23-3/4 inches long. Uses a green plastic bushing to attach to the throttle pedal. We believe that the MPC is wrong on the length. Our observations are that the 2V cable is longer than the 4V version.Replaces Ford part number D3ZZ-9A758-B.*Note - Used on 1972 Cougars after 7/10/1972 and all 1973 Cougar and Mustangs. Look at your throttle pedal end for verification. I doubt that...

Throttle cable for many 1972 and all 1973 Mercury Cougar and Ford Mustang Q code 351-4V engines. Cable length 23 inches long. Identified by the blue plastic bushing on the throttle pedal end of the pedal. We believe that the MPC is wrong on the stated length, the 4V cable is shorter than the 2V version.Replaces Ford part number D3ZZ-9A758-C.*Note - Used on 1972 Cougars after 7/10/1972 and all 1973 Cougar and Mustangs. Look at your throttle pedal end for verification. I doubt that...

Reproduction throttle cable for the Cougar or Mustang equipped with the 351 engine. Cable length 24 inches long, check your application. There were size differences between the 2V and the 4V engines. Replaces Ford part number D3ZZ-9A758-C. *Note - Used on 1972 Cougars after 7/10/1972 and all 1973 Cougar and Mustangs. Look at your throttle pedal end for verification. I doubt that date, I think it was much earlier, than July 1972. ...

Black moulded plastic gas pedal pad for all 1971, 1972 and 1973 Mercury Cougars regardless of engine or transmissions. Used pads with various amounts of wear on the surface. Ford part number: D1ZZ-9735 or D1ZZ-9735-A Stainless surround trim available too, part number D1ZZ-9735-B.

SBVALVCOVER Ford engine blue painted valve cover with "Powered by Ford" embossed in the metal. Correct on 1968-1971 Mercury Cougar and 1968-73 Ford Mustang with 289/302/351W engines. Ford master parts catalog shows a right and left version of this cover those Service Replacement numbers are D2OZ-6582-C & D2OZ-6582-D. *Note - This cover will not work on a 351 Cleveland engine.

replaces Ford part # 385161-S Zinc - Dichromate (yellow - rainbow) finish

Reproduction A/C Tag Retainer for the 1967 - 1973 Mercury Cougar

Accelerator pedal shaft assembly that mounts to the engine firewall. For use with 1972 Mercury Cougars built after 6/19/1972, and all 1973 Cougars. Has a hole for either a green or blue plastic bushing on the cable end.

York compressor for air conditioning systems for Mercury Cougar and Ford Mustang. These should be professionally inspected or rebuilt and our compressors have all been in storage for some time. Shipped without pulleys, clutches, or valves. The York compressor is constructed mostly of aluminum and is lighter than the Tecumseh brand compressor by 10 pounds. The York compressors are less common too, subject to availability. We often see part numbers on the York tag (which does not list a Ford...

Tecumseh compressor for air conditioning systems for Mercury Cougars and Ford Mustangs. These should be professionally inspected or rebuilt and our compressors have all been in storage for some time. These Tecumseh compressors came with a front oil fill plug up until 1967, thereafter, they have a top fill plug. Top fill is the most common, and likely what you will receive, unless you specify the 1967 style with front fill. These units are shipped without pulleys, clutches, or valves. The...

For 1972-73 Mercury Cougars and Ford Mustangs with the 351W engine. This is a Pitts manufactured pulley and clutch assembly with a pulley diameter of 6-5/16", a clutch diameter of 5-1/8", and an overall thickness of 1-11/16 inches. Whew boy, say that 5 times fast!Ford part # D2ZA-2981-A. May also have part numbers of D2ZA-2981-A1A, D2ZA-2981-A1B, or D2ZA-2981-A2A.

Reproduction OE steel power disc brake line kit for Mercury Cougars 1973. See the inset image for where to look for the date of manufacture of your Cougar to know which lines to order. This item is bent and may be drop shipped from the supplier when it is ordered and is available in OE steel or stainless steel. These kits include all of the steel lines that run from the master cylinder to the wheel cylinders, but it does not include the flex tubes that connect to the caliper.

Reproduction stainless steel power disc brake line kit for 1973 Mercury Cougars. See the inset image for where to look for the date of manufacture of your Cougar to know which lines to order. This item is bent and may be drop shipped from the supplier when it is ordered and is available in OE steel and stainless steel. These kits include all of the steel lines that run from the master cylinder to the wheel cylinders, but it does not include the flex tubes that connect to the caliper. ...

Original Style Steel 5 Piece Brake Line Set for the 1973 Mercury Cougar and 1973 Ford Mustang with Front Power Brakes and a build date after July of 1972.

Brake line rubber grommets for any 1967-73 Mercury Cougar or Ford Mustang. These are the ones that go through the shock towers for the front brake lines. Drum or disc, all the same. Sold as a PAIR. Ford number 373624-S.

Used bolts, and usually new washers. Convertible kit comes with 4 - "A" bolts, 4 "B" bolts, 10 new washers. Kit fits all 1970-73 Mercury Cougar and Ford Mustang convertibles. Coupes or hard tops would include shoulder belt hardware. We will make sure these original seat belt bolts are damage free and rust free. The gold finish will be degraded. There were minor and major changes almost every year. We also have hundreds of used belts and belt sets that we cannot possibly list all of, so give us...

384543-S8 Power steering pump adjusting spacer for use without air conditioning. For most 1970 - 1973 Mercury Cougar or Ford Mustang with 351C engines. Spacer dimensions: 7/16" I.D. and 1/2" thick.*Note 1970 and later cars with 302 or 351W engines use a 3/4 inch spacer.

Excellent reproduction of the little 1 1/8" wide plastic emblem found on every 1970 - 1974 three spoke steering wheel pad. This emblem can also work on the 1969 - 1973 two spoke steering wheel pad but it is not an exact fit as the two spoke wheel emblem is only 1 1/32" wide. Keep in mind we made these EXACTLY as original so they are very fragile. If you happen to break the emblem anytime within three years of purchasing it we will sell you a replacement for half price when you submit the...

This emblem was located on either side of the quarter panel in 1968 and both front fenders in 1971 - 1973. The studs on the 71-73 were a little longer but this 1968 emblem is an excellent substitute. Fantastic quality part... In our experience, we have found that you would have to obtain several NOS emblems before you found one with chrome as nice as this. The quality on these new emblems is very consistent. The plating is very inconsistent on the original Ford emblems. We are very excited to...

This is the correct emblem that came in the center of the hood moulding on a 1973 Standard model Mercury Cougar. It would not look out of place on an XR7 but of course would not be correct. Ford part # D3WY-16637-A. This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit of 50% of our web price for parts delivered in hand or by carrier to our Brooks, Oregon location. If you're not interested...

This "Stick On" Cougar rear deck emblem was only used on models without the XR7 package. They are often missing as once the factory double sided tape dries out they are often lost forever. We also have a few very nice used examples in stock.We often get asked about where to place 69-70 XR7 and Cougar adhesive emblems. Based on personal experience and pictures from the original Ford archives the answer would be "Pretty much wherever you think looks best". Often as seen in this picture the line...

High quality reproduction adhesive emblem for your deck lid. Measures 6.5" wide by 2.35" tall. It has the correct black paint applied to the sides. If you have a 71-73 Cougar this chrome emblem is a much better match to your other emblems even though it is not technically correct. We often get asked about where to place 69-70 XR7 and Cougar adhesive emblems. Based on personal experience and pictures from the original Ford archives the answer would be "Pretty much wherever you think...

Good used emblem with no bends, but will be scratched. Will need new adhesive tape as these did not come with studs. For any Cougar, but only came on 1969-70 Standard Models, and all 1971-73 Mercury Cougars. 1971-73 XR7 and Standard Models, as well as convertible.We often get asked about where to place 69-70 XR7 and Cougar adhesive emblems. Based on personal experience and pictures from the original Ford archives the answer would be "Pretty much wherever you think looks best". Often as seen in...

This small sized Cougar emblem (1 3/8" long) was used on 1969 - 1973 Cougars without AC. It was affixed to a block off plate in the very venter of the dash by two peened over die cast studs. It will glue back in place nicely and many Cougar fans have found fun "custom" applications for this attractive piece. This emblem will not be pitted or scratched in any way.

This Super Cobra Jet emblem was never used on a Cougar, but is the Cobra Jet emblem used on the Hood Scoop for 1969-1970 Mustangs. It is also an attractive emblem for your custom application. Thanks for the plug Mark!: "My first deal with Don was clear back in the 1980s and I have sent a few people his way and all came away happy. While at his shop on Monday I watched Lin crawl under a convertible, phone in one hand and a tape measure in the other, and measure a cross...

This used grade B emblem will have good chrome and mounting studs, but the plexi center will be faded. These can be opened up and repainted from the backside. The paint can be obtained from stores that sell modeling supplies. These mount on the lower part of the roof behind the quarter windows. This part of the roof is also known as the 'C' pillar. Ford engineering number on backside is D1WB65517A20-AB. We also offer new barrel nuts for installation. ...

These fender emblems look much like the 1968 quarter panel emblems but differ in that they have longer studs that fasten via barrel clips as opposed to a speed nut used on the 1968 quater panel emblems. The Ford casting number on the backside is D1WB-16098-AA. For the money, The 1968 repro quarter emblem is a much better buy . ...

Used XR7 door panel emblems for the Mercury Cougar. The emblems shown are not faded, most likely the emblem you receive will be faded from black to a bronze color. Keep in mind the cat always walks forward. Sold as a pair.

Found on the lower right corner of all 1971 - 1973 Cougars equipped with the XR7 Interior package. Both mounting studs will be in place and it will have a nice overall finish. Ford engineering number as seen on the backside is D1WB-65061A58-AA.

Good used emblem with no missing studs, cracks or pitting. We rarely have this one in stock.

Reproduction lock cylinder set for the ignition and doors on the Mercury Cougar or Ford Mustang. Replaces Ford part # D2AZ-6222050-A.

Door striker replacement bushing.   .90 tall, .69 OD. .49ID. .10 thickness. These plastic bushings were used starting in 1972. We also sell the whole striker assembly. Common striker to many Ford cars after 1971. Apparently Sikorski helicopters too.

Door Striker bolt assembly complete with PVC bushing. 7/16-14 thread. Silver zinc finish. Replaces Ford part #: D2AZ-6522008-A.

Plastic insert with metal locking retainer. Replaces Ford part # C5AZ-6221952-A. NOTE* This clip will need to be squeezed on the clip side in order to obtain a good grip. Check out our handy diagram below to find other '67-'68 door parts you may need. All the item numbers shown can be typed in to the search bar on our site. (Click image to view full size) ...

Replaces Ford Part #: D1ZZ-6221813-A