1971 Mercury Cougar

This is actually a kit which includes 2 hoses (Part # D1ZA-19835-A and Part # D1ZA-19837-A), the sight glass (Part # SG3, D2AZ-19D695-BK or YF-342), 2 o-rings (Part # L33,D2AZ-19D695-R or YF-368 and Part # H33, D2AZ-19D695-AE or YF-316) and a quick connect (Part # QF3,C1SZ-19B696-A or YF-241 and Part # QM6, C1SZ-19B695-A or YF-252). *Note we normally supply the new coupler with this kit. Regardless of which V-8 engine, this hose when assembled is approximately 78 inches long.Ford MPC kit #...

Reproduction A/C Tag Retainer for the 1967 - 1973 Mercury Cougar

This A/C vacuum canister mounts to the passenger side shock tower and controls damper doors inside the A/C unit. This unit includes a built in check valve. Used and tested vacuum tank and bracket, also known as the A/C vacuum reservoir. Fits all 1971-73 Mercury Cougar, 1971-73 Ford Mustang, as well as 1970-71 Ford Torino / Fairlane and Mercury Cyclone Montego, 1970-7? Ford Maverick and Mercury Comet.Replaces Ford part # D0DZ-19A566-A.  

part # 370608-S. Used in multiple places on mounting brackets. Pump to pump attaching bracket bolt. Also used on mid 1968-73 idler and adjusting A/C pulleys. See item 32389 for a longer version of this flange head 3/8-16 bolt. This bolt is 3/8-16 x 11/16".

Reproduction diaphragm pump that mounts on the front all 67 - 73 Cougar or Mustang Autolite 2V carbs as well as 1967 Autolite 4V Carbs. With today's gas, these commonly fail, especially when sitting for extended periods of time. Complete failure will cause fuel leaks, but many times these will affect performance well before a leak actually starts. Good idea to replace every few years or if sitting for 6 months or more. Replaces Ford Part #: C4AZ-9B559-A.

Molded rubber plug, seals access hole in the side of shift housing. Replaces Ford Part # : C5ZZ-7C147-B Check out this video

Floor shifter access plug. 1967-73 Mercury Cougar and Ford Mustang, also fits floor shift 1971+ Mercury Comet and Ford Maverick. Ford Part number C7ZZ-7C147-A. Check out this video

This is the part of the tilt switch that the turn signal wand screws into. This part is always included when you purchase a new turn signal switch. 1967-69 mechanism has two springs on either side, the 1970-73 mechanism uses just one spring. There is an active thread on the Classic Cougar Community Forum discussing tilt columns and trouble shooting. *NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many...

Used actuator for the seat back release on the 1971 - 1973 Mercury Cougar or Ford Mustang. This item is tested and will be in working condition. Left is the same as right, two required per car. Sold individually.

Reproduction center cap adapter kit for installing Legendary center caps on the Legendary Series GT9 wheels. The spacing is a bit deeper on these specific wheels, so this adapter kit comes with special adapters and longer screws.  This kit is intended to make original and after market Mag 500 and Style Steel wheels center caps work on the Legendary Series GT9 wheels.  Please note that the included screws may not fit the thread pattern of some center caps.  The plates will...

Adapter tube for connecting the fuel vapor purge tube to the air cleaner base. Can be either blue or black in color.

3M brand weather strip adhesive for installing the various rubber weather stripping found on Mercury Cougars on all years. This is the black colored adhesive and is the 5 ounce size.