All Available Parts - 1971 Mercury Cougar

New phosphate dipped slotted pan head screw for mounting distributor vacuum advances. Two total, per Ford distributor. We know that these fit FoMoCo, Autolite and Motorcraft marked distributors 1967-73. These are AMK screws 8-32x1". Sold individually, you will need 2. 

Gasket, for the C6 transmission filter. Fits all c-6 transmissions 1967-73 Mercury Cougar and Ford and Mustang.

Brass screw in plug for select Autolite distributor vacuum advance units from 1968-71, typically the banded single advance units factory installed. Solid brass, originals were not, we believe that they were cadmium plated. Solid plug, should be hollow, with a 3/4 inch hex head. Works as it should. Fits most all vacuum advance that have a plug in the end as shown. *Note, when removing the old plug, there is a spring and washer inside. 

3/8-16x7/8 Bolt for installation of idler, adjusting pulleys, and brackets, on most 1968-73 Mercury Cougar and Ford anything, including Mustang. Sold individually, up to 8-9 are typically used per car. 9/16" hex, washer head bolt.

3/8 washer for installation of idler, adjusting pulleys, and brackets, on some 1968-73 Mercury Cougar and Ford anything, including Mustang. Sold individually, 1-2 are typically used per car. 

Grade A used deluxe shifter handle in black. Nice used condition may have a hairline crack in the plastic on the bottom. No release button or set screw included. See related items for Grade B  Ford part number C8OZ-7213 The 67 version was actually a little different. Check out our video on rebuilding your shifter below: ...

Grade B used deluxe shifter handle various colors. Please specify color in the notes, limited to stock on hand. Fair used condition will have at least one crack in the plastic. May also have slightly pitted chrome. No release button or set screw included. See related items for Grade A  Ford part number C8OZ-7213 The 67 version was actually a little different. Check out our video on rebuilding your shifter below: ...

Internal tail shaft assembly from a FMX transmission. We only disassemble up to what you see in the picture.  *Excludes some FMX transmissions with 351C-4v in 1970. We do not have the larger diameter version available.

Internal tail shaft assembly from a C-6 transmission. We only disassemble up to what you see in the picture. 

Internal tail shaft assembly from a C4 transmission. We only disassemble up to what you see in the picture.  *Excludes later versions of C4 transmission that have thicker output shafts.

Bolt kit for installing the idler and adjusting pulley on any 1970-73 Mercury Cougar / 1970-73 Ford Mustang or 1970-73 Ford / Mercury with 302, 351W, and 351C engines. 4 bolts 3/8-16x7/8 inch washer head bolts and 1 thick 3/8 washer.  

Coil bracket mounting bolt for all V-8 engines as found in 1967-73 Mercury Cougar and Ford Mustang. This3/8-16 bolt attaches the coil bracket to various places on the engines. Either on the intake manifold or the cylinder head. Will fit stock Ford cast iron intakes as found 1967-73. AMK bolt B-13722.

Bolt and nut for the clamping the coil into the coil bracket as found in 1967-73 Mercury Cougar and Ford Mustang. Fits all of the various coil brackets used 1967-73 on most all Ford engines. This is a 8-32x1-1/2, 1/4 hex headed fine thread bolt and nut.  This is not the round headed slotted screw type that Ford also used.

Used console lid catch. Plastic piece that screws to the underside lid of your late 1970-73 Mercury Cougar or 1970-78 Ford Mustang. Yep, used on Mustang II's, too.  Ford part number D0ZZ-63060A96-B and stamped into the plastic D0ZB-63060A96-B ...

Core FMX Transmission valve body for any 1970-71 Mercury Cougar or 1970-71 Ford Mustang with code "X" transmission code on the door tag. This is only for 1970 or 1971 transmissions with P-R-N-D-2-1 shift pattern. Sold as a core, should be thoroughly cleaned and rebuilt with quality parts. These units can be upgraded with 'shift kits' to firm up shifts, add longevity, and they help reduce and eliminate clutch and band slippage. Various kits available in the aftermarket, we offer one as...

Passenger side, rear, lower corner, special cut that ties the quarter panel with the tail light panel on any 1971-73 Mercury Cougar coupe and convertible. These special cuts are removed from rust free examples from a used Cougar. Ford part number D1WY-6545118-A.

Driver side, rear, lower corner, special cut that ties the quarter panel with the tail light panel on any 1971-73 Mercury Cougar coupe or convertible. These special cuts are removed from rust free examples from a used Cougar. Ford part number D1WY-6545119-A.

Driver side, rear frame rail, from a 1971, 1972, and 1973 Mercury Cougar hard top. The Ford MPC shows a couple of different numbers and exceptions for this item. It may be the presence or absence of the nutserts for the rear sway bar option. If the sway bar nutserts are needed, please contact WCCC for availability. Full length, we cut so that there is some remaining metal on the edges. Ford part number D2WY-6510125-A.* Note - this item has dimensions in excess of 75 inches, and will ship as...

Passenger side, rear frame rail, from a 1971, 1972, and 1973 Mercury Cougar hard top. The Ford MPC shows a couple of different numbers and exceptions for this item. It may be the presence or absence of the nutserts for the rear sway bar option. If the sway bar nutserts are needed, please contact WCCC for availability. Full length, we cut so that there is some remaining metal on the edges. Ford part number D2WY-6510124-A.* Note - this item has dimensions in excess of 75 inches, and will...

Used fresh air vent found in the driver side kick panel of all 1971-73 Mercury Cougar without air conditioning. Replaces Ford part number D1WY-6501935-A.

Used fresh air vent duct found behind the driver side dash panel of all 1971-73 Mercury Cougar without air conditioning. Restoration tip - Ford used a ring of foam as a seal between the duct and fresh air vent. Replaces Ford part number D1WY-6501878-A.

Used extension or rod for the vacuum actuator for controlling the Heat / Defrost door on the 1971-73 Mercury Cougar or Ford Mustang factory integral A/C boxes. This gets screwed onto the tab on the vacuum actuator, which make the unique part numbers from the Ford MPC. About 1-3/8 inches long. For 1971-73 Cougar and Mustang. On the passenger side of the blower housing assembly. Vacuum actuator sold separately, see related items. Stamped with Ford casting number D1ZA-18A3...

Used extension or rod for the vacuum actuator for controlling the A/C heat door on the 1969-73 Mercury Cougar or Ford Mustang factory integral A/C boxes. This gets screwed onto the tab on the vacuum actuator, which make the unique part numbers from the Ford MPC. About 1-13/16 inches long. For 1969-73 Cougar and Mustang. On the driver side of the blower assembly. Vacuum actuator sold separately, see related items. This is an unstamped tab, and is plain steel color. Ford part...

Backer board for the sill plate on any 1971-73 Mercury Cougar or Ford Mustang. Also called a shield, it bridges the gap over the channel for the wiring harness. It is adjacent to the sill plate, and keeps the carpet from dropping into the exposed channel. This is a used part, and made from fiber cardboard type of material. See our reproduction item in the related items for a lower cost and made from more sturdy material. Original Ford part number D1ZZ-6513218-A. Two required per car, sold...

Backer boards (PAIR) for the sill plate on any 1971-73 Mercury Cougar or Ford Mustang. Also called a shield, it bridges the gap over the channel for the wiring harness. It is adjacent to the sill plate, and keeps the carpet from dropping into the exposed channel. This is a new part, and made from durable non paper material. See our  related items for used. Original Ford part number D1ZZ-6513218-A. Two required per car, sold as a pair.

Core FMX transmission for a 1971 Mercury Cougar or Ford Mustang. Tag number PHB-E2 or  PHB-E3. Floor shift FMX Transmission. Core transmission only, No bell housing, dip stick, dip stick tube, or torque converter. This is a rebuildable core transmission, removed from a 1971 Mercury Cougar with H code 351-2V engine. Main case inspected for damage. Heavy item, in most cases it can ship UPS ground. Easier if picked up in person.

Core C6 transmission for a 1971 Mercury Cougar or Ford Mustang, with H code 351-2V engine. Tag number PGA-AV. Floor shift C6 Transmission. Core transmission only, NO dip stick, dip stick tube, or torque converter. This is a rebuildable core transmission, removed from a 1971 Mercury Cougar with 351-2V engine. Main case inspected for damage. Heavy item, in most cases it can ship UPS ground. Easier if picked up in person.

Core C6 transmission for a 1971 Mercury Cougar or Ford Mustang, with M code 351-4V engine. Tag number PGA-AH. Floor shift C6 Transmission. Core transmission only, NO dip stick, dip stick tube, or torque converter. This is a rebuildable core transmission, removed from a 1971 Mercury Cougar with 351-4V engine. Main case inspected for damage. Heavy item, in most cases it can ship UPS ground. Easier if picked up in person.

These new navy blue shirts feature a distressed white graphic with the slogan, "It's Like A Mustang, Only Better!" and "Cougar: Since 1967", wrapped around the image of a first-generation Cougar. This design is a WCCC original, and we think it sums up most Cougar owners' true feelings about their cars. Shirts are Port & Company, 4.5-ounce, 100% ring spun cotton, with removable tags. These are softer and more comfortable than some of the previous shirts we've used. Pre-shrunk, but cold wash is...

New from WCCC! This black T-shirt features subdued grey graphics on front and back, with a small WCCC logo on the front left chest, and a rear view of a 1967-68 Cougar on the back with the taillights lit up in red. We think this is a great looking shirt that all classic Cougar fans will enjoy. Shirts are Port & Company, 4.5-ounce, 100% ring spun cotton, with removable tags. These are softer and more comfortable than some of the previous shirts we've used. Pre-shrunk, but cold wash is...

Features 274 pages / 750 photos/ 12,300 items / history / finishes / measuring and more. This book provides detailed information about the fasteners specified in assembly manuals and parts books. All 12,300 fasteners are referenced to a photo! Must have for anyone wanting to correctly put together a 1955-1973 FoMoCo product.

The latest addition to our Legendary Cougar Magazine collection. Issue #4 is an International Issue, featuring Cougars from Australia, Germany, Ireland, Norway and Sweden.In This Issue:FeaturesLuck of the Irish – Dave Rooney talks about what it's like to own the only 1967 Cougar on the Emerald Isle. LCM's Creative Consultant Brian Veit transforms Dave's photographs taken in front of his house to make it appear that they were shot in-period in a photo studio.Cougars Down Under – Owning an early...

In Issue 5, the editors have added a new department called “Cougar Marketplace,” which will follow recent sales of classic Cougars. This month, we look at the recent auctions held in Arizona and Florida. As we near the end of Volume 1, we’re looking forward to Volume 2. In Cat Tracks, co-editors Bill Basore and Rich Truesdell review the past year and look at what the future may hold for Legendary Cougar Magazine.You will also find two very useful tech articles detailing volt meter installation...

[No Description Provided]

Here's a new book about the luxury king of classic Cougars, the XR7 G! The book contains many pictures and documents never published before. A great addition to your collection!From the author of The BIG BOOK of Cougar, Don Skinner.

Get your hands on the new, long awaited Mercury Cougar Eliminator book! Besides various specifics about "optional this" and "factory that", this book includes stories written by car owners. These stories remind us that our cars are more than just a collection of technical details. They link the cars directly to the people who own(ed) them. Why did they choose a Cougar and what impact did it have on their lives? Where did it come from and where is it now? Truly, the stories and history are the...

Very nice quality reproduction turn signal lever, though the detail on the end is slightly different from the originals. Most will not notice the difference. We do get good used units in stock occasionally. Replaces Ford part # C7ZZ-13305.*NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's and is the designer of all of our solid state sequential systems. There is no question he...

Good used turn signal stalk with no rust or peeling chrome. The 1970-73 with tilt column used a stalk with an additional plastic bushing near the base. This used unit is only for the person who cares about originality in the smallest of details as our repro is a decent piece, just not exact.*NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's and is the designer of all of our...

This polyurethane steering coupler repair kit for your tilt column, commonly referred to as a "rag joint", connects the steering shaft to the input shaft on the steering box. Some customers feel polyurethane improves steering feel. Replaces factory steering coupler on 1967 - 1973 cars. Most 1967 Mustangs with fixed steering columns do not have coupler.Replaces Ford Part #: C7OZ-3A525 Check out this video ...

Fixed steering column from a 1971 Mercury Cougar or Ford Mustang. Reasonably rust free column, collapsible style. Ships as shown in picture. Often we will leave the turn signal switch in place but you should count on it being non functional. Two piece collapsible shafts have tiny plastic pins these often brake due to age or handling. Lower shaft may need to be pushed up or down for proper fitment, this is a common occurrence. 1971 and 1972 appear to be the same, but we will ship one from a...

New Walking Cat key fob featuring embossed lettering and walking cat on nickel plated steel attached to leather. A great collectors item or gift idea.

Reproduction vinyl interior upholstery kit in dark red for the standard Mercury Cougar or Ford Mustang coupe. Not to be confused with Decor level interior, this vinyl kit features horizontal stitching. Standard all vinyl interior was not available in the convertible.

Good used part without excessive rust or damaged rubber. For use with fixed column only. 1971-73 rag joints are different than the 1967-70 variety. The 1971-73 Cougar and Mustang steering box has a larger diameter shaft for attachment. Check out this video

This rubber steering coupler for your fixed column, commonly referred to as a "rag joint", connects the steering shaft to the input shaft on the steering box. This is a multi-fit part that covers many years of FoMoCo products, so you will have a couple of parts left over upon completion. Will require a grinder to remove from your old steering coupler fittings. Replaces factory steering coupler on 1967 - 1973 cars. Early 1967 Mustangs do not have coupler on fixed columns. Replaces Ford part #...

New Old Stock passenger side tail light assembly, Housing, lens, and bezel, all out of the box NOS. D1WY-13450, D1WB-13440-AA, D1WY-13489-A

Concourse correct 351 2bbl engine heater hose connector with a 90?� degree elbow that attaches to the intake manifold. Product discontinued by manufacturer. Know anyone else reproducing these? Let us know!

Used fresh air vent duct found behind the passenger side dash panel of all 1971-73 Mercury Cougar and Ford Mustangs without air conditioning. The flexible portion of this item is what fails most often. Anyone find a solution for a repair?Restoration tip - Ford used a ring of foam as a seal between the duct and fresh air vent.Replaces Ford part number D1ZA-18637-AB, the flexible hose which is stapled to this duct is marked D1ZA-18C305-AB. This icon means that we're looking to buy this part!WCCC...

"A" grade used cable and knob assembly for opening the passenger side fresh air vent on 1971-73 Mercury Cougar and Ford Mustangs without air conditioning. Cable control mounts under the dash below the glove box. Cougar uses a different mounting bracket than the Mustang. Hard to find them without broken mounting tabs. About 23 inches in total length.Replaces Ford part number D1ZA-6501890-A. This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73...

"B" grade used cable and knob assembly for opening the passenger side fresh air vent on 1971-73 Mercury Cougar and Ford Mustangs without air conditioning. Cable control mounts under the dash below the glove box. Cougar uses a different mounting bracket than the Mustang. B grade will have a broken mounting tab, but will otherwise have a good cable. About 23 inches in total length.Replaces Ford part number D1ZA-6501890-A.

Driver side, rear frame rail, from a 1971, 1972, and 1973 Mercury Cougar convertible. The Ford MPC shows a couple of different numbers and exceptions for this item. It may be the presence or absence of the nutserts for the rear sway bar option. If the sway bar nutserts are needed, please contact WCCC for availability. Full length, we cut so that there is some remaining metal on the edges. Ford part number D2WY-7610125-B.* Note - this item has dimensions in excess of 75 inches, and will ship as...

Passenger side, rear frame rail, from a 1971, 1972, and 1973 Mercury Cougar hard top. The Ford MPC shows a couple of different numbers and exceptions for this item. It may be the presence or absence of the nutserts for the rear sway bar option. If the sway bar nutserts are needed, please contact WCCC for availability. Full length, we cut so that there is some remaining metal on the edges. Ford part number D2WY-7610124-B.* Note - this item has dimensions in excess of 75 inches, and will...

1971 - 1973 Mercury Cougar and Ford Mustang convertible clear glass for the passenger side rear seating area

Used fresh air vent found in the passenger side kick panel of all 1971-73 Mercury Cougar and Ford Mustang without air conditioning. These are seldom found damage free, we call them Grade B used. Typically there is a chip in the plastic where it is attached.Replaces Ford part number D1ZZ-6501934-A or D1ZA-65019A12-AG.

This unit mounts on the main air chamber, it opens and closes the air vent. NOS or new old stock.  This unit is easy to test and can be seen by removing the glove box. Often it is the internal spring that fails on these and if your Cougar or Mustang will not easily change between blowing through the defrost ducts and the floor duct, this unit may be the culprit. Switch assembly, servo control. Tested and working, Ford box.Replaces Ford part # C6OZ-18C311-A. ...

Shaft or rod for the heater core damper door on any 1969-73 Mercury Cougar or Ford Mustang with factory or integral air conditioning. The heater damper door allows air to pass over the heater core in the fiber glass A/C box. Part cleaned for photograph, normally will ship 'as removed'. Inspected for damage or weakness of the metal. Shaft only, door not included, but available. See related parts.Replaces Ford part number C9ZZ-19C774-B.*Note will not work in 1967-68 A/C boxes. ...

This A/C vacuum canister mounts to the passenger side shock tower and controls damper doors inside the A/C unit. This unit includes a built in check valve. Used and tested vacuum tank and bracket, also known as the A/C vacuum reservoir. Fits all 1971-73 Mercury Cougar, 1971-73 Ford Mustang, as well as 1970-71 Ford Torino / Fairlane and Mercury Cyclone Montego, 1970-7? Ford Maverick and Mercury Comet.Replaces Ford part # D0DZ-19A566-A.  

This A/C thermostat is made by the original supplier and stops the evaporator coil from freezing up. Replaces Ford part #: C7ZZ-19618-A and D1ZZ-19618-A.

Used rear defog wiring harness for any XR7 Model 1971-72 Mercury Cougar. XR7 models only, this harness is the main under dash harness that plugs into the back light glass or defog switch. This listing does not include the jumper wiring harness to the heated back glass, or the relay.*Note - will not fit a 1971-72 Standard Model Cougar, the switches are different.Ford part number D1WB-18C617-AB.

Single cylinder head from 1971 Mercury Cougar with 429CJ engine. Sold as a core, needs thorough cleaning and rebuilding prior to use. Typically this cylinder head has 2.24 and 1.72 inch valves, and the chambers measure out at 73.5cc. With stock pistons, these heads will net an approximate compression ration of 10.5:1. Basic cylinder head number is 6090.  Also fits all 1970-71 Ford or Mercury with the J or C code 429 Cobra Jet engines, including Torino and Cyclone.Ford casting number...

Chassis black aerosal paint for all 1967-73 Mercury Cougar and Ford Mustang engine compartments. High temperature (advertised up to 350°). Manufacturer boasts resistant to cracking and flaking, chemical resistant to gasoline and brake fluid (but don't let brake fluid accumulate). *NOTE* Chemicals can only ship UPS ground only. Please, no foreign orders or USPS shipping allowed.Check out our video below on chassis upgrades: ...

WE CAN NOT SHIP THIS PRODUCT INTERNATIONALLY WITHOUT SHIPPING IT AS HAZARDOUS MATERIAL. THIS WILL INCUR HAZARDOUS MATERIAL CHARGES VIA UPS AND SOME COUNTRIES DO NOT ACCEPT IMPORTING THIS PRODUCT. This ORR LAC chassis black paint will give the appearance of an expensive, baked on finish. Also usable on other tools, equipment, vehicle frames, shop racks, trailers and more. ORR-LAC 923 Semi Gloss black.

D1ZZ-6501508-B This is the correct hanger for a 1971 Mercury Cougar or Ford Mustang and 1972 cars up until 6-25-1972, with power disc front brakes, and with manual transmissions. If you have a manual transmission car with worn out clutch bushings this is a great replacement part for you as it will have been removed from an automatic transmission equipped car which means the clutch bushings will be in mint, unused condition. Ford master part number D1ZZ-6501508-B for power disc front brakes.

New old stock Bendix master cylinder for 1968-69 Mercury Cougar and Ford Mustang with factory power disc brakes. This is a Bendix manufactured MC with proper 2227161 number and stop bolt on the bottom. Also has the dimple forward of the front brake line.  Includes a new cap with diaphragm as shown. The cap is not assembly line correct as this is a service replacement part.*Note even though this is a brand new unit, it should be tested for leaks prior to installation. Things happen when...

As seen in our YouTube video, this is a representation of the used, rebuilt and reproduction parts that we recommend you purchase to convert to disc brakes. If you do purchase this package we will insist on speaking with you prior to shipping as you may want to substitute parts based on what year your car is, manual or automatic. We also take in factory original drum brake spindles from 1971-73 cars.  Fun fact: 100% of all 1973 Mercury Cougars came with disc brakes from the factory. Check...

Rear bumper filler for any 1971-72 Mercury Cougar. No chips or cracks. Does not come with fasteners or clips. See related items for new aftermarket style clips for attaching, 8 total are needed. Replaces Ford part number D1WY-17808-A . * Note - Will not fit 1973 Mercury Cougar.

For use with a clutch pedal. Longer arm than drum brake pedals. Pedal shipped bare, picture may show hardware and pedal pad with trim. 1971-73 Mercury Cougar or Ford Mustang with 3 or 4 speed manual transmission and disc brakes.Replaces Ford part number D1ZZ-2455-A.

Each kit contains the seals for one caliper assembly. Replaces Ford Part #: C8ZZ-2B120 and #C8ZZ-2B121Check out our caliper tips and tricks video below: ...

This rod was used on the Bendix brand booster (crimped together case). It measures 5 3/4" long. Used on many Ford products including Torino, Cyclone, Ranchero, Cobra, Fairlane and others. This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit of 50% of our web price for parts delivered in hand or by carrier to our Brooks, Oregon location. If you're not interested in store credit, just shoot...

Rare find, NOS rubber rub strip for the front bumper guard on 1971-72 Mercury Cougar. These hard rubber bump strips attach to the front bumper guards with 2 studs from the back side. Sold individually, right is the same as left, Ford Casting number as found on the back is D1WB-17A812-AB

D1WY-17C838-A Deflector or driver side bumper filler, 1971-72 Mercury Cougar. This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit of 50% of our web price for parts delivered in hand or by carrier to our Brooks, Oregon location. If you're not interested in store credit, just shoot us an email and we will let you know if it's is something we can pay cash for. We do not send cash for parts...

Factory used clip for attaching the long black plastic rear bumper filler on any 1971-73 Mercury Cougar. A total of 8 clips are needed to attach the rear bumper filler. Most have either broken with age, or have broken during the removal of the filler. Sold individually. Limited supply of used, we also stock a suitable reproduction clip. See Related.

This option includes paying a core charge. By choosing this option, the re-chromed bumper you receive will have started the re-chroming process as an average quality core. We highly recommend that you send us your core first. Here's why: We can core match your bumper. Bumpers that are re-chromed using a superior quality core are always reserved for core matching. If your core is average or below average, you may be able to pay to upgrade to a re-chromed bumper that started the re-chroming...

This option REQUIRES sending your core in advance. Here are the advantages of pre-sending your core: We can core match your bumper. Bumpers that are re-chromed using a superior quality core are always reserved for core matching. If your core is average or below average, you may be able to pay to upgrade to a re-chromed bumper that started the re-chroming process as a superior quality core. You can find out the quality of your core before paying a core charge and avoid unnecessary core charges....

Rear bumper filler for any 1971-72 Mercury Cougar. No chips or cracks. Comes with fasteners. Replaces Ford part number D1WY-17808-A . * Note - Will not fit 1973 Mercury Cougar.

Rebuilt FMX torque converter for the 1969 - 73 Cougar or Mustang. This item carries a $200 core charge, refundable when we receive your rebuildable core.Ford part number C9ZZ-7902-A. What does it mean to “rebuild” a torque converter? When there are problems with a car’s automatic transmission, sometimes it’s the torque converter. It could be fluid loss, bent vanes, or bad bearings among other problems. We have a local shop with decades of experience do a very thorough rebuild that is...

License to rear bumper spacer used on all 1971 - 1972 Cougars. Usually this item is badly cracked or missing. This is a show quality used part for those that are concerned about less than obvious detail items. Replaces Ford part number D1WB-17226-AA.

This Cougar II 1/25 scale factory sealed model kit was made by the Industro Motive Corp in Troy Michigan. This car was actually introduced in 1964 and was a Shelby Cobra based Ford- Cougar prototype vehicle that never made it into production.    Features: Retractable lightsWorking steeringOpening doorsOperating windowsPressure vent flapTubular frameChrome wire wheels260 cubic inch high performance engine ...

This listing is for a pair of walking cat die cast chrome cufflinks. These would be great for the serious collector who may want to add a bit of Cougar flair to outfit when hitting the town, or simply just another bit of memorabilia to add to their collection.  Walking Cat measures 1-3/16" across.

Leather manual shift boot for the Classic Console Cruiser Console that we offer. Check out our video on rebuilding your shifter below: ...

NOS 1983 Ford manual on how to read and understand vacuum diagrams. Although it's technically made for older cars, it has tons of useful information on how to decode diagrams. Includes sections on vacuum theory and applications, devices, hoses, schematics and system diagnosis. This handy book has information pertaining to how the engine creates vacuum, the carburetor and it's vacuum pressure regulation characteristics as well as air intake, fuel induction, emissions and ignition. As an...

NOTE: A FEW CUSTOMERS HAVE MENTIONED THAT THE INSTRUCTIONS MAY BE WRONG. SWITCHING PINS 1 AND 5 HAD A BETTER RESULT. IF YOU RECEIVE THIS PART AND ARE HAVING TROUBLE WITH THE INCLUDED INSTRUCTIONS, TRY SWITCHING TO SEE IF YOU GET THE SAME RESULTS. Make those horns sound like they should! These relay kits work just like my headlight relay kits to deliver full system voltage to your horns. Ford used horn relays on many vehicles into the early seventies. Unfortunately Mustangs after '65 and...

Used wiring pigtail that runs from the under dash harness to the radio on the 71 - 73 Cougar.

Nice used original Rotunda, over the counter dealer accessory. Stainless steel construction, weighs just under 8 pounds with hardware. Actual dimensions are 20 1/2 inches wide, 48 1/2 inches long, and the back lip is 3 inches tall. Installation hole spacing is as follows. Rear spacing 47-11/16" on center, front spacing (nearest the rear window) is 47-9/16". The spacing on short sides are 18-3/4" on center. This rack was utilized for may years on many cars. The same company made them for...

These plates show average wear and can be used as is, or restored to look new.NOTE: The plates and plate numbers pictured are exactly what you'll receive. 

These plates show almost no wear and would look right at home on a show car.NOTE: The plates and plate numbers pictured are exactly what you'll receive.

Rebuilt starter for the 67 - 73 Cougar or Mustang equipped with a small block engine. This item requires a $25 core charge.

NOS spare tire lock for the 68 - 73 Cougar Mustang and Torino. Spare tire locks were first offered as an option in 1973, but will fit on any year from 1968 to 1973. The ford master catalog shows that all years from 68 - 73 whether it be Cougar, Mustang or Torino all had the correct size stud for this lock to fit. Fits spare tire hold down J bolts with 1/2-13 course threads, common on Fords 1968-73.  Ford part number D3FZ-1386-A. J bolt not included. ...

Reproduction GOLD HAZE lug nut cover deigned to fit the Cobra / Eleanor style Legendary LW90 wheel.  Sold as a set of 4 and includes 20 Legendary low profile lug nuts.

Pair or reproduction clips used to hold your transmission cooling lines together and keeps them from rattling.

Pair of reproduction license plate frames bearing the name of the the original Lincoln / Mercury dealer lot in San Jose, California.  Chrome with the city and dealer name written in/on reflective material. Sold only as a pair.

This is for seats designed for the center release, if your chrome T handle release knob is mounted on the side of the upper portion of your bucket seat this will not work on your application. Side release linkage can be found here.

1971 - 1973 Mercury Cougar and Ford Mustang coupe / convertible Grade A factory tinted glass for the driver side door

Application; 390, 427, 351CJ, 428CJ, and 429CJ all with C6 transmission. 428CJ and 429CJ 4 speed transmissions. 1970 351C-4v with FMX.U-joint size 1330, overall length 8-3/4 inches.

Used spare tire lock for the 68 - 73 Cougar Mustang and Torino. Spare tire locks were first offered as an option in 1973, but will fit on any year from 1968 to 1973. The ford master catalog shows that all years from 68 - 73 whether it be Cougar, Mustang or Torino all had the correct size stud for this lock to fit. Fits spare tire hold down J bolts with 1/2-13 course threads, common on Fords 1968-73. Ford part number D3FZ-1386-A. J bolt not included. This icon means that we're looking...

Reproduction pair of black seat belt buckle bezels for the Mercury Cougar, Ford Mustang, or Ford Torino. It is little details like these that often make the difference between first and second place at the show. 

D1ZZ-6523312-A Bracket that attaches the end of the power window motor to the door on the passenger side of 1971-73 Cougar and Mustangs with power windows.

D1ZZ-6523313-A Bracket that attaches the end of the power window motor to the door on the driver side of 1971-73 Cougar and Mustangs with power windows.

These are original looking seat belts at affordable prices. These are not Concours reproductions, but have the correct vintage look used by Ford on several cars in the Mid to Late 1960's. Starburst Medallion used on the buckle is an exact copy of originals. Hardware included!Sold individually

Attractive reproduction of a very popular, over the counter Mercury dress-up accessory. The only Cougars that came from the factory with this real wood shifter were the 1970 Eliminator and 1968 XR7G. The XR7G used a gold Cougar "Walking Cat" emblem and the 1970 Eliminator used the silver emblem. Of course this will look great on any 1967 - 1973 Cougar. Click on images to enlarge. ...

Round plastic window stop that attaches to the front and rear door window glass on all 1971-73 Mercury Cougar and Ford Mustangs. Two per door