All Available Parts - 1970 Ford Mustang

D0ZP-7976-A Aluminum bell housing, sometimes called a converter housing in the Ford shop manual. 1970 - 1971 Mercury Cougar and Ford Mustang with any 351 engine and automatic FMX transmission, code X on your door data plate tag. Ford master part number D0ZZ-7976-A.

Replacement seal with boot for all 1969-73 FMX and 1967-73 C6 transmissions. Tail shaft and slip yoke seal. 

Replacement seal with boot for all 1965-73 C4 Ford transmissions. Tail shaft and slip yoke seal. 

Replacement tail shaft bushing, for all 1969-73 FMX and 1967-73 C6 transmissions. 

NOS retainer / friction clips that replace broken injected plastic shaft retainers on fixed or tilt steering collapsible columns on most FoMoCo products starting in 1968 and through the 70's. These installs on the upper piece of what Ford called the Steering Column Shaft Assembly, also known as the inner steering column collapsible shaft.  The Steering Column Shaft Assembly is the 2 piece shaft that connects the steering wheel to the rag joint. The upper piece of this shaft...

This clip goes on the upper end of your column and keeps your steering shaft from moving around when you pull up on your steering wheel.See item 31804 for new clip.

New old stock brass intake manifold fitting that screws into the rear of the 428 CJ intake manifold on all 1969 428 Cobra Jet engines. Similar to the 1967-68 version, but this one has an additional smaller nipple coming out of it.  Ford part number C8OZ-9A474-A.

Steering column locking gear. For all 1970-73 Ford and Mercury steering columns. Made of brass, has 8 teeth and is 7/16 inches thick. Fits fixed and tilt steering columns. Ford part number D0AZ-3E717-A.*NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year.

This is a plastic cushion, washer and/or spring between the lower knuckle and inner tube on a 1968 - 1973 tilt-away steering column. These have a larger diameter than the 1967 plastic cushion.*NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year.

1970 Mercury Cougar / Ford Mustang columns were a weak design from the factory. We find that all the columns we get have some degree of excessive play, some will not even hold position. The design was improved upon greatly as the years went by and spending a little more on an updated / rebuilt one is well worth the investment. This is a 100% complete column with key and all parts needed to convert from a fixed to a tilt column. You can use your existing plastic plastic color keyed collar and...

Good chrome, better fit than the reproductions we sell.

Very nice knob with no missing / lifting chrome. If you don't mind some damage on your knob we have plenty that are less than perfect, mention it and we will give you one for free with your order.

Used steel lower dash panel for all 1970 Mercury Cougar and Ford Mustang with factory air conditioning. This is a bolt in dash section, ships bare, no brackets included. Grade B  = some pitting and or extra holes. Replaces Ford part number D0ZZ-6504320.

Used threaded PCV valve for use on 390-4V, 428CJ, 427-4V cars from 1967-70. Unknown functioning condition, these have the correct threaded tops and work with either of the 90° elbows available, reproduction or OEM Ford.

D0ZZ-6A664-A Original used hose that connects the original threaded PCV valve combination with C7OZ-6A706-A elbow and the carburetor spacer plate. Molded hose with 5/8" valve end and 3/8" spacer plate end. 1970 428CJ and 428SCJ engines, includes Cougar and Mustang only. Used hoses will have faded striping (if present), and clamp impressions. Very often the rubber will be hard and showing some degree of stress cracks. *Note - Excludes 1967-69 S code 390-4V and 1968-69 428CJ engines. See part...

C9OZ-6A664-A Original used hose that connects the original PCV valve to the carburetor spacer plate. All 1969-70 351 Windsor 2V and 1969 351Windsor 4V engines. Used hoses will have faded striping (if present), and clamp impressions. Very often the rubber will be hard and showing some degree of stress cracks. This hose is a bit longer than the 289/302 version due to the taller deck height of the 351 Windsor engines. *Note - These molded and contoured hoses were designed to work with the...

D0AZ-6A664-C Original used hose that connects the valve cover mounted PCV valve and the carburetor spacer plate on 1970 Mercury Cougar and Ford Mustang 351 Cleveland engines both 2 and 4 barrel versions."L" shaped hose, 1/2" in diameter, approximately 15-1/4 inches long. Used hoses will have faded striping (if present), and clamp impressions. Very often the rubber will be hard and showing some degree of stress cracks. *Note - Excludes 1969-70 351W or Windsor engines. *Note - These molded and...

Precision machined to the factory specifications. Light gold anodize finish just like the original.

This adapter is threaded on bottom for PCV valve and 6 degree angled 5/8" nipple on side. Was gold Cadmium plated, not painted. Original Ford part number C7OZ-6A706-A.

This adapter is threaded on bottom for Boss 302 / 390-4V / 428CJ PCV valve and 6 degree nipple on side. Gold Cadmium plated, not painted originally. This only works with the OEM or reproduction threaded PCV valves.Replaces Ford Part Number C7OZ-6A706-A.

Factory cast iron exhaust manifold set, both a correct right C9ZE-9428-A and left C9ZE-9431-A side matching exhaust manifolds. 1969 and 1970 Boss2 Eliminators

For 1967-68 Mercury Cougars and Ford Mustangs with the 289 or 302 engine. This is an Eaton manufactured pulley and clutch assembly with a pulley diameter of 6-5/16", a clutch diameter of 6", and an overall thickness of 2-1/16 inches. Ford part # C7AA-2981-F.

Tested and working used Lo tone horn. The Lo tone is indicated in raised letters located on the perimeter of the horn. 1969-70 Mercury Cougar and Ford Mustangs used part number C9ZF-13802-C Lo tone. Every horn is bench tested and inspected for cosmetic defects, if they do not function properly, and pass a visual inspection, they get recycled. The used horns at WCCC can be used as-is or you can clean and detail them for you show car.

Tested and working used Hi tone horn. The Hi tone is indicated in raised letters located on the perimeter of the horn. 1969-70 Mercury Cougar and Ford Mustangs used part number C9ZF-13801-B Hi tone. Every horn is bench tested and inspected for cosmetic defects, if they do not function properly, and pass a visual inspection, they get recycled. The used horns at WCCC can be used as-is or you can clean and detail them for you show car.

Easy to install quality reproduction. Includes crescent spring and correct aluminum pin that features shoulder and locking knurls. Does not look or feel much like the original. Not really a stock color, fits 1968-71 cars and about 1 month into 1972. Please see the window crank handles to see the difference between 1968-71 handles and 1972-73 window crank handles. Replaces Ford Part # C8AZ-6223352 *TIP* To install remove your window crank and place knob and crank in the jaws. To protect the...

Replated original door handles from premium western pit free cores. We sell these on an exchange basis but keep in mind we cannot take pitted cores in exchange. Ford Part #: C7ZZ-6522404-A and C7ZZ-6522405-A

Tested and working emergency or parking brake indicator switch. Foot parking brake switch found on 1969-70 Mercury Cougar and Mustang with visibility group option. Includes bolt to attach to emergency foot brake. Ford part number: C6GB-15652-A

We often will have B grade knobs with less than great chrome plating for lots less money. Plan on ordering new knobs, we have lots of colors to choose from.This is a good used original front window crank with no obvious scratches or pitting. It will be missing the decal that covers the screw sometimes it will have a knob, most often it will not. Ford part number is C8AZ-6223342-A, casting number on back reads C8AB-6223348-B or D0AB-6223348. *NOTE* This handle will work on a 1968 even though it...

Due to the small amount of clearance between the back of your speaker and the door glass when lowered, these and their 30 watt little brother are the only speakers on the market that will replace your worn out originals and fit like OEM without modifications. Features Kenwood 60 watt peak power speakers, nice upgrade over the low wattage originals. Sold as a pair.   These pictures show what every 69-70 door panel looks like on the backside.  They are all perforated from from the...

These four original hinges have been rebuilt with steel sleeves to retain the over-sized oil impregnated bushings. They feature hollow hinge pins which allows grease to fill the steel tube, lubricating the bushings under pressure from the inside-out. The threaded Zerk fittings are easily accessible from inside the car when the door is opened and are guaranteed to NEVER wear out or we will rebuild them for FREE! This offer has been in place for 20+ years by our rebuilder and they have never...

Used door window stop, cover plate, for any 1969-70 Mercury Cougar and Ford Mustang. These were originally painted body color, and were laid on either inside the front cowl or the package tray for painting. The one for the doors is roughly 25/32" x 3-3/8 inches long, the holes are 5/16, and the spacing is 1-25/32 on center to match the stop. Replaces Ford part number C9ZZ-65234A30-A.

Ford never made these in stainless but what a great upgrade! The advantage we see with these is that they do not dent or scratch as easy when you release your seat belt. They also can be polished easily (unlike anodized aluminum). These weigh 1.5 pounds each, triple of what the originals weigh. Sold as a pair only. *NOTE* Since these are stainless they look great next to our "accessory" stainless steel sill plates we offer. The secondary "accessory" strips cover the painted portion of the door...

This is a used fuel door insert we have cleaned up, painted the background black and installed a 1967-1969 headlight door walking cat emblem on. The original 1970 ELIMINATOR piece that this resembles had a smaller sized cat so this is not exactly correct for your original 1970 Eliminator.

Used passenger side (right hand) spring from a door latch assembly fits many Ford and Mercury cars. This will fit all years 1967-70. 

Used driver side (right hand) spring from a door latch assembly fits many Ford and Mercury cars. This will fit all years 1967-70. 

For 1969 Mercury Cougars and Ford Mustangs with the 390 or 428CJ engine. This is a Pitts manufactured pulley and clutch. Pulley diameter 6-3/4", clutch diameter 6", and an overall thickness of 2-1/16 inches. Ford part # C9AA-2981-G.

For 1969 Mercury Cougars and Ford Mustangs with the 351W engine. Also 1970 Mercury Cougars and Ford Mustangs with the 351W or 428CJ engine. This is a Pitts manufactured pulley and clutch assembly with a pulley diameter of 6-3/8", a clutch diameter of 5-3/16", and an overall thickness of 1-11/16 inches. Whew, say that 5 times fast!Ford part # C9AA-2981-D.

New Old Stock set of brushes only fits the Eaton brand of air compressor clutch. Pitts compressor clutch is the most common one starting in 1969. These are exact reproductions made from the original tooling.Ford part #: C8SZ-2979-A

Stainless steel throttle pedal surround trim. Self attaching to part number C9ZZ-9735-A. This used part may have some wear, but will not have broken tabs. Fine steel wool really shines these up. In the Master Parts Catalog this part is called a cover, Ford part number C9OZ-9735-A. Not all Mustangs received this trim for the accelerator pedal, but it will attach, no problem. The more common 1965-68 version also fits like a glove. You would need to place them side by side to see the minute...

Used oil screen pick up tube assembly from a 1970-74 small block 335 series, or 351C or Cleveland Ford car. This is for front sump oil pans. Used item, should be degreased and cleaned inside and out prior to installation. Tube assemblies with damaged screens, damaged tubes or bends are thrown away or scrapped. We only save undamaged, used oil pick up tubes. Melling sells a quality reproduction of this item. Replaces Ford Part #: D1AZ-6622-A

Stainless steel throttle pedal surround trim. Self attaching to part number C9ZZ-9735-A. This used part may have some wear, but will not have broken tabs. Fine steel wool really shines these up. In the Master Parts Catalog this part is called a cover, Ford part number C9OZ-9735-A. Not all Mustangs received this trim for the accelerator pedal, but it will attach, no problem. The more common 1965-68 version also fits like a glove. You would need to place them side by side to see the minute...

Spring that gives tension to the to your accelerator pedal. We have a limited number of these NOS springs. They came in a bulk FoMoCo package so we cannot offer you the original packaging.

Sold individually, original glove box cable screw with shoulder. For any 1967-70 Mercury Cougar or Ford Mustang. Probably many other Ford and Mercury cars also.Ford part number 379202-S2.

Cable length 22.83 inches long, identified by a plastic ball shaped end attached onto the pedal side of the cable. Must be used with a 1970 accelerator pedal shaft. This is an unbroken part. Notice there are two versions, one has plastic covering the cable and the other has an exposed cable.

Reproduction disc brake caliper insulators for a large array of FoMoCo products starting in 1968. 2 are required per caliper, 4 total per vehicle. Sold as a pair. Replaces Ford part # C8AZ-2B299-A.Check out our caliper tips and tricks video below: ...

Used on front re-tractors, two per side on either side of the re-tractor mounting hole. Used to prevent rattles.

Four nuts per bucket seat, 8 total nuts per car with bucket seats. Sold individually. Replaces Ford part # 378643-S. Phosphate & Oil (gray & black) finish

Unlike our reproduction nuts these good used original nuts can be purchased individually and they cost less to boot! 8 required per car, 4 per bucket seat.

C9ZE-6583 Cast aluminum valve cover. Correct on 1969-1970 Mercury Cougar and Ford Mustang with 428CJ engines. This is the plain finned aluminum valve cover. Ford master part number C9ZZ-6582-B. Casting number can also be C9ZE-6583-B. Sometimes called 1969 Shelby valve covers. *Note - Some 1969-70 428 Super Cobra Jet engines came with a different style of  "Snake" finned aluminum valve covers.

SNAKECOVER Cast aluminum valve cover. Correct on some 1969-1970 Mercury Cougar, Ford Mustang, Shelby GT-500 with 428CJ and 428SCJ engines. This is the 'Snake' aluminum valve cover. Ford master part number C9ZZ-6582-B.

C9ZE-6583-G Cast aluminum valve cover with. Correct on 1969-1970 Mercury Cougar Eliminator and Ford Mustang with Boss 302 engine. This is the finned aluminum valve cover. Ford master part number is C9ZZ-6582-C. *Note - Most, if not all 1969 Boss engines came with a chromed steel valve cover. Research did not turn a part number for that valve cover. Likely it is a chromed 351C valve cover. If you have the part number for the stamped steel chrome Boss 302 valve cover please share. ...

Brightens the engine compartment and looks sharp. Fits our big block finned aluminum valve covers (item# 26018) and others with the round push-in style opening. Requires a rubber grommet to fit into the valve cover, which is usually included with new valve covers.Does NOT fit valve covers with the "stovepipe" fitting (like our small block finned aluminum units) or factory valve covers the tabs for twist-on oil caps. This cap is for after market valve covers.

Used front console support bracket. Held in place by 2 phillips screws at the front, under the console. NOTE: There were two versions of this bracket, a shorter version without holes and a longer version with holes. See reference photo above.

Used front console support bracket. Held in place by 2 phillips screws at the front, under the console.NOTE: There were two versions of this bracket, a shorter version without holes and a longer version with holes. See reference photo above.

Used middle console support bracket. Held in place by 2 rivets midway under the console.

Chromed engine oil dipstick as found on all 1970 Mercury Cougar and Ford Mustang with 428CJ engines (Q or R Code). Top of shield to dip stick is 20 inches. The handles were chromed originally. Ford part # D0OZ-6750-C, Ford casting # D0OE-6750-C.*NOTE* This is an improved dipstick that better reflects the actual full mark, from previous 428CJ dipsticks.

Chromed engine oil dipstick as found on all 1970 Mercury Cougar Eliminator and Ford Mustang with Boss 302 engines (G Code). The handles were chromed originally. Ford part # D0ZZ-6750-B, Ford casting # D0ZE-6750-C.

Reproduction blue dipstick tube for the Mercury Cougar or Ford Mustang equipped with the 351 Windsor.

Used oil screen pick up tube assembly from a FE or big  block 1966-70 Ford car, such as 352, 390, 410, 428, or 428CJ engine. This is for most front sump oil pans. Used item, should be degreased and cleaned inside and out prior to installation. Tube assemblies with damaged screens, damaged tubes or bends are thrown away or scrapped. We only save undamaged, used oil pick up tubes. Melling sells a quality reproduction of this item. Replaces Ford Part #: C6OZ-6622-A ...

One piece molded rubber gasket with metal core. Keeps the rails flat and rigid, and prevents damage from over-tightening. Made by Fel-Pro. Oil pan SnapUps are included for easy mounting. This is by far the best oil pan gasket on the market.

The oil filter made by the original Ford supplier.

This oil filter is absolutely concours correct. A must for Show. All are silk-screened with multiple colors.

Reproduction set of after market cast aluminum valve covers with COBRA 428 lettering. Fits any FE style Ford engine, including 390, and 428 cubic inches.

This 1/2" tall unique little screw was used on several different trim parts on the early Mercury Cougars. You will notice the reproduction has a larger head (The two on the right in the lower picture are repros) than both of the used versions typically found on 67-73 Cougars. This will be a benefit to those that have elongated screw holes on your wheel lip mouldings from corrosion or improper removal. In 1967 - 1968 there were eight per wheel lip moulding, two per fender extension moulding,...

Single sheave pulley 6-61/64 inches in diameter.Applications:1970 Boss 302 Eliminators without power steering1970 351 engines without power steering1971 - 1973 351 engines without power steering and without A/C.Ford casting number C9OE-8509-E. Ford part number C9OZ-8905-B *Note - this is a very shallow pulley, it is meant to run in the second belt position from the engine. ...

We have a VERY limited supply of seat tracks that are taken from cars that have never been in the weather. These should need nothing but cleaning and lubrication. Fits all 1967-70 Mercury Cougar including convertible, and 1965-70 Ford Mustang. Used kit includes C5ZZ-6561704-F, C5ZZ-6561705-F, and C5ZZ-6561726-A. Note that many of the 67's do not have the rectangular plate in place as seen here. We have a separate listing for those if you want to match your existing version. ...

D0ZZ-7528-C Equalizer bar or "Z" bar for FE big block engines with a manual transmission. Both 3 and 4 speed manual transmissions. This is a used part and it will most likely show some wear form previous use.

D0ZZ-7528-D Equalizer bar or "Z" bar for 351 cubic inch Cleveland engines with a manual transmission. Both 3 and 4 speed manual transmissions. This is a used part and it will most likely show some wear form previous use. See the 1969 listing if you have a 1970 351 Windsor engine. This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit of 50% of our web price for parts delivered in hand or by...

D0ZZ-7528-E Equalizer bar or "Z" bar for Boss 302 Eliminators 4 speed transmissions only. This is a used part and it will most likely show some wear form previous use.

Crankshaft oil slinger for all FE Ford V-8's, starting 1958 until at least through 1976. 1967-69 390 engines, 1968 427-4V engines, 1968-70 428, 428CJ, 428SCJ engines, 1958-66 352, and 1968-76 360 engines. Goes on the crankshaft after the timing gear and before the timing chain cover. It does have a purpose on the vintage engines. Outside diameter 3-5/16 inches. Ford part number B8A-6310-A.

Used on 1970 - 1973 Kelsey Hayes, style steel wheels, 14 x 6". Master Parts Catalog description: 15-1/4" O.D., 11-3/16 I.D., 2-1/4" wide. No dings and only the slightest scratches.The part number is D0DZ-1210-A and the engineering number is D0DA-1210-B. Sold individuallyFits the following models with styled steel wheels: 1970 Ford Mustang1971 Ford Mustang1972 Ford Mustang1973 Ford Mustang 1970 Ford Torino1971 Ford Torino1972 Ford Torino1973 Ford Torino 1970 Ford Maverick1971 Ford Maverick1972...

Used on 1970 - 1973 Kelsey Hayes, style steel wheels, 14 x 6". Master Parts Catalog description: 15-1/4" O.D., 11-3/16 I.D., 2-1/4" wide. No dings and only the slightest scratches.The part number is D0DZ-1210-A and the engineering number is D0DA-1210-B. Sold individuallyFits the following models with styled steel wheels: 1970 Ford Mustang1971 Ford Mustang1972 Ford Mustang1973 Ford Mustang 1970 Ford Torino1971 Ford Torino1972 Ford Torino1973 Ford Torino 1970 Ford Maverick1971 Ford Maverick1972...

Used clutch pedal return spring with two original nylon bushings. Ford Part #: C8OZ-7534-B.

Made of heavy gauge steel with a satin black painted finish. Replaces Ford Part #: C9ZZ-7535-A.

Application, 1969 - 1970 390IP / 428CJ & 428SCJ engines without air conditioning. Casting number 80B. 5-1/2" diameter and 7/16" sheave width.

C9ZZ-7528-A Equalizer bar or "Z" bar for 351 cubic inch Windsor engines and Boss 302 Eliminators with manual transmissions. Both 3 and 4 speed manual transmissions. This is a used part and it will most likely show some wear form previous use.

Used on 1969 Mustang Mach I and Eliminator and all 1970 Mustangs and Cougars. American Cushion Industries' cushions are reinforced with tough polypropylene mesh backing material for stability and long life. All of their products, including highback cushions are molded with their exclusive cold cure process. Upper and lower cushion for one seat. Click on images to enlarge. ...

Reproduction chrome knob for the seat track release to adjust the position of the seat. This knob is an exact replica of the original and installs with a hidden set screw. A simple way to dress up your interior while maintaining a stock appearance. Made from chrome plated die cast metal.Sold individually. Replaces Ford Part #: C5AZ-6261753-BA.

C8OZ-8509-C 1968 427 / 390-4V without air conditioning and 1968-1970 428CJ without air conditioning. Thermactor on all applications, power steering optional. 3 sheave pulley with two different diameters. The MPC lists it as 6 inches on the dual sheave portion and 5-1/16 inches on the outer but we find the actual outer most measurements to be 6 1/8" wide on the dual pulley and 5 3/16" wide on the single sheave pulley. When laid on a flat surface the height is 2 3/8" tall. Ford casting number...

C8AZ-8509-D 1969 428 Super Cobra Jet only (V and W code axles), 1970 428CJ and 428SCJ prior to Sept 1, 1969. No air conditioning, power steering permissible. Three sheave pulley, 6-1/8 inches and 7-1/8 inches in diameter pulleys. Ford casting number C8AE-8509-C was originally imprinted in ink, if you look closely between the two bonded together pulleys that make this pulley up you may be able to read the C8AE-8509-A stamped casting number from the two sheave inner pulley.

Used crank shaft pulley for any 1970 Mercury Cougar or Ford Mustang with Boss 302 engine. This is a double groove pulley with a 5-13/16 inch inner pulley diameter, pulley turns the water pump and alternator. 6-5/8 inches diameter for the smog pump belt. This pulley would have been used without power steering. Also used only up until about Jan, 1970. After Jan 1970, Ford just installed a 3 sheave pulley with the middle sheave not being used. Replaces Ford part number D0ZE-6312-A. ...

Replaces Ford Part # D0WY-14305-C & D0WY-14305-A

D0OE-6312-C For both Cleveland and Windsor 351 engines. This is also the "with air conditioning" pulley, but with power steering option. Triple sheave 8.00", 7-55/64", 6-9/16" diameters. A four bolt hole crank shaft pulley for use with 1970 and upward crank dampeners. Ford Master Part number D0OZ-6A312-B. This is a Service Replacement pulley for D0AE-6312-C. *Excludes 1972 Q code 351 Cobra Jet engines. This means all 1972 351C-4V engines.

D0ZE-6312-B Application is 1970 Boss 302 Eliminator with or without power steering. Triple sheave pulley 5-15/16" and dual outer 6-11/16" diameter. Ford Master Part number D0ZZ-6A312-A. Also a four bolt mount to the crankshaft balancer. The reason for a triple sheave pulley on Boss 302 engines is the inclusion of the Thermactor Smog system from the factory. Smog pumps were placed so that they worked off of the outermost pulley groove on a 3 sheave crankshaft pulley. If with power steering the...

Fan spacer, measuring 1-1/2 inches. Application includes 1970 Mercury Cougar and Ford Mustang with 351 engines and standard cooling. Reference number YA-21, cross reference to C8OE-8546-A spacer.Ford part # D0AE-8546-B, Ford engineering # D0AZ-8546-B.

Fan spacer, measuring 1-39/64 inches and sometimes mentioned as 1.61". Reference number YA-71.Ford part # C8DE-8546-A, Ford engineering number C2OZ-8546-G.

Fan spacer, measuring 1-7/8 inches or sometimes mentioned as 1.88". Application includes 1970 Mercury Cougar and Ford Mustang with 428CJ engines. Reference number YA-81.Ford part # C8AE-8546-C, Ford engineering # C6OZ-8546-D.

Fan spacer, measuring 2-1/8 inches. Application includes 1971 Mercury Cougar and Ford Mustang with 429CJ engines. Reference number YA-83.Ford part # C8SE-8546-B, Ford engineering # C8SZ-8546-D.

C9AF-10A352-A or -B Alternator pulley for use with only one drive belt. Just under 2-3/4" inches in diameter. This later version would have a casting number of C9AF-10A352-A or possibly C9AF-10A352-B stamped on it. Ford master part number is C5AZ-10344-K like the above pulley.

This plastic cover was put in place to cover the void at the very top of the panel. They are side specific and the textured side is installed upwards, on the bottom side you will find the Ford engineering number C9ZB-7654607-A and are marked L.H. for the passenger side.

Vacuum tested working hot water valve for any 1969-73 Mercury Cougars or Ford Mustang equipped with factory A/C. This valve stops the flow of warm coolant in the heater hose, when the A/C is on. Has the original cast brass valve and vacuum pod. Used but functional, the reproduction version is very good, but has a black plastic valve, like the service replacement valves from Ford.Replaces Ford part number C9AA-18495-D.

These are used hose clamps that have a tab and fold over on them selves. These were dipped in a rubber like substance to prevent chaffing. The ones that we have available do have some cracking or damage to this coating. It should be easy to 'dip' them again with the product that is available in most hardware stores. We normally see 2 of these clamps, or straps bundling the hoses on most cars. These clamps should fit a variety of different Ford and Mercury products, not just Mustang and Cougar....

Here is your concours correct A/C suction hose for your beloved Mercury Cougar or Ford Mustang.This hose is compatible with both 134a and R12 refrigerants.

There are 2 manufacturers of these hoses and many places will call them a "concours" hose. Neither manufacturer make an exact replica of the original sight glass hose. The finish of the hose does not match, but the most obvious difference is that the sight glass itself has a hexagon shape instead of a square shape. If you would prefer a good used original, give us a call, we can usually dig one up for you. Remember to remove your coupler between this hose and the dryer, it will be need...

Reproduction A/C discharge service valve that fits on top of the compressor and is an exact copy of the original. Verify your high pressure hose size when ordering, this unit has the 3/4" fitting. This valve accepts the R134A connection, not the R12.

Reproduction A/C suction service valve that fits on top of the compressor and is an exact copy of the original. Verify your high pressure hose size when ordering, this unit has the 7/8" hose fitting. Replaces part # D0AZ-19752-A or D0AA-19752-A.

Grade B used A/C center vent for any 1969-70 Ford Mustang. This will some limited chrome pitting in the plating. Fits all models of 1969 and 1970 Mustang. Limited to stock on hand. Does not come with attaching clips, see 'related' tab. Rear dimensions: 6 x 2-1/4 inches. Replaces Ford casting number C9ZZ-19863-A and C9ZA-19C683-A.

Grade A used A/C center vent for any 1969-70 Ford Mustang. This will have almost perfect chrome plating, minor blemishes only, no pitting. Fits all models of 1969 and 1970 Mustang. Limited to stock on hand. Does not come with attaching clips, see 'related' tab. Rear dimensions: 6 x 2-1/4 inches. Replaces Ford casting number C9ZZ-19863-A and C9ZA-19C683-A.

This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit of 50% of our web price for parts delivered in hand or by carrier to our Brooks, Oregon location. If you're not interested in store credit, just shoot us an email and we will let you know if it's is something we can pay cash for. We do not send cash for parts in advance but we often can compensate you within hours of receiving the...

Stud that the factory line workers used for locating the air conditioning pedestal bracket. Then backed up with a nut. Used on 289 / 302 / 351W / 390 / 428CJ pedestals from 1967 - 1973. We sell this item as reproduction, see related items.*Note - Excludes 351C and 429CJ.