1970 Ford Mustang

NOS fixed column turn signal switch for the 1970 - 1972 Mercury Cougar or Ford Mustang.Ford part number D2AZ-13341-C *NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world's most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's and is the designer of all of our solid state sequential systems. There is no question he cannot answer! Here is a link to a great source of information on the subject. ...

NOS fixed column turn signal switch for the 1970 Mercury Cougar or Ford Mustang. Ford part number D0ZZ-13341-A or D0ZA-13B302-C. *NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world's most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's and is the designer of all of our solid state sequential systems. There is no question he cannot answer! Here is a link to a great source of information on the subject. ...

Our turn signal switches are tested and working. If you have replaced your sequential unit in the trunk with one of our new solid state sequential units and are still having problems then the turn signal switch is most likely the culprit as the only other part to the system is the wiring harness itself. Often when your brake lights are not working the turn signal switch is the culprit as the brake lights feed through the turn signal switch. Replaces Ford part # D2AZ-13341-C. Replaces Ford...

Reproduction concours correct premium thermostat for the 351C. This is the correct thermostat you would use in conjunction with the new concourse restrictor / by-pass plate on 70 - 73 Cougars and Mustangs equipped with a 351 Cleveland engine. This is a the assembly line style thermostat.  Replaces Ford part number D0AE-8575-B.

Reproduction aluminum cast A356 water neck for FE Big Block engines. Made from original factory blueprint, and includes the correct stamping. Will fit the 67 Big Block, but markings are correct for 68. Replaces Ford Part #: C8AE-8592-B.

Cable length 22.83 inches long, identified by a plastic ball shaped end attached onto the pedal side of the cable. Must be used with a 1970 accelerator pedal shaft. This is an unbroken part. Notice there are two versions, one has plastic covering the cable and the other has an exposed cable.

This rare accessory was only offered over the counter, it was not available as a factory option. Great upgrade for the 1970-1973 Cougar owner as cruise control was discontinued after 1969 and not offered again until 1974 on the Mercury Cougar.Ford part number C8OZ-9B742-AClick on images to enlarge. ...

Used timing chain cover from a  351W or Windsor engine from 1969-70 Mercury Cougar and Ford Mustang or most any 1969-70 Ford with 351W. Honestly, we have found that most of the 1969 production year came with the C8AE-6059-A timing cover. Cast aluminum construction without excessive damage. Installation bolt kits also available. The C8AE-6059-A timing cover can be used on 1970 302 and 351W engines, as long as you use the 1970 timing pointer. The 1970 timing pointers use alternate...

Used stamped steel pointer mounts to timing chain cover. Correct for 1970 Mercury Cougar with 351W engine, and 1970-72 Ford Mustang 302 and 351W. At least two distinct versions of this pointer may be availbable. Starting in 1970, Ford V-8 engines had timing pointers installed on the passenger side of the engine, and a companion harmonic balancer with 4 bolts for attaching crank shaft pulleys. Uses two of the timing cover bolts for attaching. Replaces Ford part C9TZ-6023-A. This icon means that...

This is an upgraded version from what you see in our video but the idea is the same. This tool has a square hole so you can use your 3/8" drive ratchet or breaker bar to get the correct angle and have even better control of your leverage when placing the torsion bar into the slot. Used to remove the hinge springs (torsion rods) off the 1967 - 1973 Cougar or Mustang. No more trying to remove with the wrong tools . These can be tricky to remove without this tool.  Will not work on 1964 -...

This is a mirror nut bezel tool used to remove the mirror nut on the 1967 - 1968 and 1970 - 1973 Cougar. No more scratches trying to remove with the wrong tools. These are made from HRS steel and are milled to fit the bezel nut. This tool pays for itself each time you use it. NOTE: This is an exact fit for ALL used mirror nuts (bezels) and the 1970 - 1973 reproduction mirror nuts (bezels). However, you will find it does not fit our 67-68 repro mirror nuts (bezels) and will need some filing to...

Driver side (left hand) outer section of the torque box for the Mercury Cougar and Ford Mustang for both coupe and convertible.