1970 Mercury Cougar

Reproduction set of after market cast aluminum valve covers with COBRA 428 lettering. Fits any FE style Ford engine, including 390, and 428 cubic inches.

Same as our crinkle finished Mercury Cougar valve covers but with a polished finish. These are rarely in stock so do not be surprised if our system will not let you order. We get these from Scott Drake and the only reason they polish a few sets a year is when they find a set of black covers that have a defect, they send them in to be polished. So... The only time we have these in stock is when they find blems to polish. Please do not ask us when we expect to get more in, we have no idea when...

C7AZ-6571-B

Good used axle vent nipple or tube. This vent tube screws into the top of the rear axle and is a breather / vent to equalize the pressure inside the axle tube. Fits both 8 inch and 9 inch rear axles. Fits Mercury Cougar and Ford Mustang 1967-73.  A (5/16" inside diameter) rubber hose about 18-1/4 inches long attaches to the nipple. Has a very tiny diameter hole inside, about 0.062". Needs to be kept clear to work properly. Also see the reproduction version from AMK. Concours hose kit with...

This hand held cart was used by service stations or garages to hold spools or bare wire to make them easily accessible when needed. There's a handy foot long ruler painted into it to quickly and easily measure lengths of wire. The design and style suggests that it could be from anytime between 1940 and 1970, making it a valuable collectors item for car enthusiasts. Condition is used, but aside from obvious defects and patina (see photos above, random wire included),...

New old stock instrument voltage regulator Ford part number C9AZ-10804-ACheck out this video of our Gauge Tester

New Old Stock Warning light panel from a 1970 Standard model Mercury Cougar. This is the light panel in the center of the dash. There are four visual check items that light up, 'BELTS', 'LOW FUEL', and 'DOOR AJAR', 'LIGHTS'. This one has a black rubber trim. Ford part number D0WY-10C854-A.

Dated 0A22, January 22, 1970. Big block Ford water pump core, suitable for rebuilding. This version has a casting number of C9AE-8505-A. Found on many Ford 390, and 428CJ engines from 1970. These have casting dates, we list the dates when we have them in stock. Plan on sending it to a vendor that specializes in water pump rebuilding. In all likelihood, the rear cover, heater tube, and impeller will need replacing. See our other core water pump listings for other casting numbers. Dead...

Dated 9M6, December 6 1969. Boss 302 or 351C Ford water pump core, suitable for rebuilding. This version has a casting number of D0OE-D. Found on many Ford 351 Cleveland engines from 1970. These have casting dates, we list the dates when we have them in stock. Plan on sending it to a vendor that specializes in water pump rebuilding. In all likelihood, the rear cover, heater tube, and impeller will need replacing. See our other core water pump listings for other casting numbers....

NOS Water bypass plate for all Ford 351C engines. This is an original in the package brass restrictor plate for 1970-73 Mercury Cougar or Ford Mustang Torino etc.Limited to stock on hand. Replaces Ford Part number D0AZ-8K517-A. Check out this video

WE CAN NOT SHIP THIS PRODUCT INTERNATIONALLY WITHOUT SHIPPING IT AS HAZARDOUS MATERIAL. THIS WILL INCUR HAZARDOUS MATERIAL CHARGES VIA UPS AND SOME COUNTRIES DO NOT ACCEPT IMPORTING THIS PRODUCT. Red Line Water Wetter Cooling System Treatment is a unique agent for cooling systems that doubles the wetting ability of water. It offers rust and corrosion protection that allows for use of straight water in racing or reduced antifreeze levels in warm climates. It also improves heat transfer and...

Includes all five pieces. Front bow rubber seal is C9ZZ-7653986-A. Side rubber seals are C9ZZ-7651564-A, C9ZZ-7651565-A. Much better fit than reproduction, perfect for that high end restoration.