1967 Ford Mustang

Replaces Ford Part # : C7ZZ-7507-B

C5OZ-7515-B Manual transmission clutch fork - 3 and 4 speed, stick shift transmissions. Fork measures 9-1/4 inches long. Specifically used with a 157 tooth flywheel, as opposed to the 164 tooth fly wheel used after Feb 1968.Replaces ford Part # C5OZ-7515-B.  Cougar before 2-15-1968, 289/302 Engines.  Mustang before 2-15-1968, 289/302 Engines. *Note - This style of clutch fork uses the 'wire' for the holder, not the clip. ...

C5OZ-7515-B Manual transmission clutch fork for small block V8 engines - 3 and 4 speed, stick shift transmissions. Fork measures 9-1/4 inches long from the divot where the rod rides to the tip of the forked end. Specifically for the C5DA-6394-A bellhousing that used a 157 tooth flywheel. Cougar 1967 through 2-15-1968. XR7, XR7-G. Mustang 1965 through 2-15-1968. 2+2, GT. Fairlane 1965 through 2-15-1968. 500, XL, Custom. Torino / Ranchero 1968 through 2-15-1968. 500, XL Comet 1965 through...

Used until early (prior to 2/15/1968) on manual transmission cars. Comes with rivets. Replaces Ford part #: B9AZ-7522-B.This style uses the early clutch fork with the anti rattle wire.

Manual transmission clutch kit for all 1967-73 Mercury Cougar or Ford Mustang with 3 or 4 speed transmissions and 289, 302, or 351 engines. This is a 10 inch disk, pressure plate, throw out bearing, pilot bearing, and alignment tool. The clutch disc is asbestos free.

Manual transmission clutch kit for all 1967-73 Mercury Cougar or Ford Mustang with 3 or 4 speed transmissions and 351 or 390 engines. This is a 11 inch disk, pressure plate, throw out bearing, pilot bearing, and alignment tool. The clutch disc is asbestos free.

This pedal assembly is a copy of the 1967 clutch pedal. It can be used on 1968 with no modifications. Fits all engine applications. Has replaceable shaft as shown. Replaces Ford Part #: C7ZZ-7519-A.

C7ZZ-7519-A We also offer used clutch pedals along with our quality reproduction 1967-1968 clutch pedal. These pedals will no doubt show some wear around the clutch rod holes. Three and four speed pedals are all the same. Mustang is the same too.

Bumper that helps stop the 'clunk' noise when you take your foot off of the clutch pedal on manual transmission 67 - 68 Cougars and Mustangs.Replaces Ford Part Number: C7ZZ-7583

This kit has everything you need to repair your clutch and brake pedal and pedal support in one easy kit. Repairs 1967-73 Mercury Cougar or 1965-73 Ford Mustang. Plus many other Ford cars. This kit requires welding. For use on pedal hangers that are all wallered out, or 1971-73 pedal hangers that are not round. Kit has roller bearings. Quality Scott Drake / Holley product. *Hint - All 1967-70 brake pedal hangers have the clutch pedal shaft bushings, even the automatic cars. The originals are...

This reproduction stainless trim mounts over your pedal pad. Not only adds style but also holds your pad in place. Replaces Ford part number C5ZZ-7B544-A.

D1TZ-7600-A New Old Stock service replacement clutch pilot bushing for all 1965-71 390/428/429 engines with manual transmissions. Will fit 1967-71 Mercury Cougar and Ford Mustang with 390-4V, 428CJ, 428SCJ, and 429CJ engines with 4 speed manual transmissions. Fits Fairlane, Cyclone, Torino, Ranchero also.