All Available Parts - 1967 Ford Mustang

NOTE: WE SUGGEST LOCAL PICK UP ONLY FOR CORE ENGINE BLOCKS BECAUSE WE CANNOT GUARANTEE BLOCKS WILL NOT HAVE CRACKS INTERNALLY. Dated 5L18, November 18, 1965.  Used 0.030 over bore 4.180" Ford 428 engine block. Bare block, no crank shaft. Will be used, dirty. Good for rebuild or assembly, quality of machining unknown. Bare block, may have C6ME, castings. When we have them in stock we will post the casting date or dates. Heavy, will require either local pickup or freight...

Used Distributor / 289-2V / Automatic Transmission for the 1967 Mercury Cougar / 1967 Ford MustangFord part number C7AF-12127-AE  

NOTE: WE SUGGEST LOCAL PICK UP ONLY FOR CORE ENGINE BLOCKS BECAUSE WE CANNOT GUARANTEE BLOCKS WILL NOT HAVE CRACKS INTERNALLY.Used standard bore 4.00" Ford 289 engine block. Will be used, dirty, have measurable taper, and will have a ridge. Good for rebuild. Bare block, may have C6AE, C8AE, castings. When we have them in stock we will post the casting date or dates. Heavy, will require either local pickup or freight shipping.  Dated 6K4 or October 4, 1966.  This item cannot ship...

NOTE: WE SUGGEST LOCAL PICK UP ONLY FOR CORE ENGINE BLOCKS BECAUSE WE CANNOT GUARANTEE BLOCKS WILL NOT HAVE CRACKS INTERNALLY. Dated 7L1, November 1, 1967.  Used standard bore 4.05" Ford 390 engine block. Will be used, dirty, have measurable taper, and will have a ridge. Good for rebuild. Bare block, may have C6ME, C7ME, castings. When we have them in stock we will post the casting date or dates. Heavy, will require either local pickup or freight shipping.  This item cannot ship...

NOTE: WE SUGGEST LOCAL PICK UP ONLY FOR CORE ENGINE BLOCKS BECAUSE WE CANNOT GUARANTEE BLOCKS WILL NOT HAVE CRACKS INTERNALLY. Dated 8B1, February 1, 1968.  Used standard bore 4.05" Ford 390 engine block. Will be used, dirty, have measurable taper, and will have a ridge. Good for rebuild. Bare block, may have C6ME, C7ME, castings. When we have them in stock we will post the casting date or dates. Heavy, will require either local pickup or freight shipping.  This item cannot ship...

NOTE: WE SUGGEST LOCAL PICK UP ONLY FOR CORE ENGINE BLOCKS BECAUSE WE CANNOT GUARANTEE BLOCKS WILL NOT HAVE CRACKS INTERNALLY. Long block, factory A code 289-4V V-8 engine. Rated at 225 Hp with 9.8:1 compression ratio in 1967. Not standard bore engine block, that may or may not have been in running condition when pulled. May or may not have 9.8:1 pistons. Guaranteed to be rebuildable. Complete engine less carburetor, distributor, exhaust manifolds, fan, accessories, pulleys, and flex...

Reproduction ignition switch w/ cylinder and 2 keys for the 1967 Cougar or Mustang.NOTE: The item comes with economy keys, they are much thinner than the premium Ford keys. The cylinder will not accept the premium keys. Here is a helpful "How To" youtube video on how to replace your ignition switch.

Featured in this kit are all the basic items you need to convert your small block 1967 - 1968 Cougar or Mustang from a 20" wide radiator with a fixed four blade fan to a 24" wide radiator with 3 cores and the MAXIMUM cooling big block, high performance 7 blade clutch fan. This setup was used on the highest horsepower drive-trains of the day including the Legendary 427 Side-Oiler equipped GTE and the 428 SCJ Drag-Pak equipped Cougars and Mustangs. This might sound like overkill for your small...

Used on the ignition lock cylinder. This unit locates and maintains the angle to the dash from behind. Attaches with one small screw, and the bezel and retainer nut secures the whole works to the dash from the front. 1967-68 Mercury Cougar and Ford Mustang.

This Autolite capacitor is stamped with part number C6OA-18832-A. It attaches to one of the lugs on the voltage regulator, bullet lead plugs into wiring harness. Sometimes called a radio ignition interference suppressor. About 1-15/16" inches long. This is one of those small detail items that judges like. All Ford and Mercury vehicles from 1966-1971 used this "Autolite" marked capacitor when a radio was installed by the factory. Starting in 1972 there is a Motorcraft version which has a...

Used Autolite water temperature sending unit, fits Ford 289, 302, 390, 427, 428CJ. 260° stamped, for Mercury Cougar 1967-69, and Ford Mustang 1966-69.  Ford number C6DZ-10884-B. *Note - these are specifically NOT for 1969 351W. Ford had a unique part number for that one engine.... and we don't stock that one. Sorry. Check out the video below on our new gauge tester: Check out our video on replacing the fuel system on a '68 Cougar! ...

Used Bracket for mounting the Servo on any 1967-68 Mercury Cougar or Ford Mustang with speed control. The Servo is the rubber bellows. Ford part number C7ZZ-9C736-A.

Brass sensor that screws into intake manifold and activates temperature gauge in dash. Replaces Ford Part #: C6DZ-10884-B (SW-552) or C9WY-10884-A (SW-888)*. Temp Sender Switch Temp Rating : 15.2-19 Ohms Resistance At 220 Deg F Temperature Switch Thread Size : 3/8" x 18 NPT * - The 1969 351 Windsor temperature sending unit has been discontinued. Most manufacturers list the 1968 302 temperature sending unit as the closest replacement.Check out the video below on our new gauge tester: ...

Reproduction pair of drum spindles for the 67 - 69 Cougar or Mustang. Our supplier started with a set of used but excellent condition Ford originals and created these spindles and double checked them against original Ford blueprints. They're constructed from FORGED JIS S45C grade steel, and a protective, black e-coating was applied. All surfaces are precision machined. Special care was taken to ensure bearing tolerances were identical to Fords. For an extra measure of safety and...

1967-1973 14 amp Buss style glass tube fuses sold in a package of 5 and used in multiple positions. They are used for courtesy, instrument cluster, door, map, glove box, pillar, luggage compartment, and clock lamps. Also for the lighter, ignition key on and head lamp on buzzers.

Oil pressure sending unit 1967-68 Mercury Cougar and Ford Mustang 289/302 oil warning light style. This part actually goes back to 1956. Used on various Ford and Mercury engines from 1956-68. Clip on style wiring harness should be verified prior to purchase. *Note - Not for XR7Check out the video below on our new gauge tester: ...

Big bell shaped oil pressure sending unit for 1967-73 Mercury XR7 and 1967-73 Ford Mustang with actual oil pressure gauges instead of idiot light for the oil pressure. *Note - this pressure switch does use the press on wiring boot. Please check your wiring harness for the proper connector. This oil pressure sending unit also fits the following cars that have analog oil pressure gauges: 1969-71 Continental MKIII, Thunderbird 1965-71.Replaced Ford part # C9ZZ-9278-A Check out the video...

Good used tray that is not currently reproduced. Most people prefer the group 24 battery but for those that want to keep it very original, this is getting to be a hard to find part with no rot (will show pitting). Many that are not rotted have been cut to accept a group 24.

Good used group 24 tray for 1967 Mercury Cougar or Ford Mustang. Assembly line installed group 24 battery tray with holes for tilt vacuum canister. For those that want to keep it very original, this version is not reproduced. This is getting to be a hard to find part with no rot (will show pitting).

Reproduction driver side spindle for the 67 - 69 Cougar or Mustang. Our supplier started with a set of used but excellent condition Ford originals and created these spindles and double checked them against original Ford blueprints. They're constructed from FORGED JIS S45C grade steel, and a protective, black e-coating was applied. All surfaces are precision machined. Special care was taken to ensure bearing tolerances were identical to Fords. For an extra measure of safety and durability, the...

Reproduction passenger side spindle for the 67 - 69 Cougar or Mustang. Our supplier started with a set of used but excellent condition Ford originals and created these spindles and double checked them against original Ford blueprints. They're constructed from FORGED JIS S45C grade steel, and a protective, black e-coating was applied. All surfaces are precision machined. Special care was taken to ensure bearing tolerances were identical to Fords. For an extra measure of safety and durability,...

In 1967, one could order from the factory a power drum brake Mustang or Cougar. In 1968 - 1973 that option was discontinued and all you could order was manual drum all the way around or power disc in front with drum in the back. This kit is for the person who already has the power booster and pedal in place and wants to convert to power disc in the front. Since the 1967 model year used the same spindles for disc or drum brake cars you can do this conversion and never even have to take your car...

New front outer wheel bearing for original drum and disc brakes for all 1967-69 Mercury Cougar and 1967-69 Ford Mustang with V-8 engines. These are tapered bearings with cone or race. Inner diameter is 0.75 inches. These are dry bearings, meaning they will need to be packed with chassis bearing grease, prior to installation. A large inner bearing and this outer bearing are required for each side. Two of each needed for the front wheels. *Note - This bearing only fits the 1967-69 spindles,...

New front inner wheel bearing for original drum and disc brakes for all 1967-69 Mercury Cougar and 1967-69 Ford Mustang with V-8 engines. These are tapered bearings with cone or race. Inner diameter is 1.25 inches. These are dry bearings, meaning they will need to be packed with chassis bearing grease, prior to installation. A smaller outer bearing and this inner bearing are required for each side. Two of each needed for the front wheels. *Note - This bearing only fits the 1967-69 spindles,...

NOS grease cap for front wheels of the Mercury Cougar or Ford Mustang. 2 Required per car, sold individually. New from Ford. Replaces Ford part # B5A-1131-A.

Stamped steel construction with black vinyl coating like the original to prevent corrosion. Please note that vinyl coating will almost always crack along edges shortly after installation, just like the originals did... This is the same exact hold down you will see listed elsewhere its just that we feel you should know what you are getting up front so you will not be surprised. Replaces Ford part #: C5AZ-10718-A.

Right side. Bracket to hold the junction of the steel brake line and the rubber brake hose. Mounts to the frame rail. Fits 1967 Mercury Cougar and Ford Mustang with factory installed Kelsey Hayes 4 puck disc brakes only.Ford part number C5ZZ-2082-C.

Left side. Bracket to hold the junction of the steel brake line and the rubber brake hose. Mounts to the frame rail. Fits 1967 Mercury Cougar and Ford Mustang with factory installed Kelsey Hayes 4 puck disc brakes only.Ford part number C5ZZ-2082-D.

Reproduction front emergency / parking brake cable for the Mercury Cougar or Ford Mustang. These are made just like the originals, are concours correct and includes the firewall seal and firewall bracket. Replaces Ford part # C7ZZ-2853-A.

This kit was sold by Ford Service Departments back in the day for those who were tired of their manual drum brakes. This kit includes all you will need to convert your six cylinder Mustang or V8 Cougar / Mustang from manual to power drum brakes. Technically it is correct only for a 1968 but will work on any year 67-70. The conversion carries a Ford part number of C8ZZ-2A091-A. Ford was generous and gave you both a manual transmission and a automatic transmission brake pedal in the kit. When...

This reproduction emergency / parking brake cable equalizer mounts to the end of the parking brake release assembly and captures the emergency brake cable. A very nice reproduction!Replaces Ford part # C6OZ-2A602-A.

Used emergency / parking brake assembly for a Mercury Cougar or Ford Mustang as removed from a West Coast Cougar organ donor. This unit may have some minor rust. Normally we assemble with reproduction cable.Ford part # C7ZZ-2780-B.

This reproduction emergency / parking brake idler bracket welds to the under side of the floor on the driver side (left hand) of the vehicle and has the factory spec pin.

This passenger side (right hand) reproduction emergency / parking brake cable idler bracket mounts to the right front floor pan. The idler bracket is often discarded when the floor pan is removed for replacement. We also have good used units in stock for those that desire 100% correctness.

4 oz. tube of non-melting, water resistant grease for disc and drum brake hardware, hood hinges, window regulators, quarter windows, vent window hinges, pretty much whatever needs lubing. A little dab will do ya!Do you have questions about Glue-In vs Bolt-In glass? How about how to properly install Glue-In glass in your 1969 Cougar or Mustang? Check out our video below for some great glassy information!1969 Glue-In Glass: The Comprehensive Repair Guide Video ...

This kit contains all the replacement springs and hold down components required to do a professional job on rear drum brakes. Kit includes enough parts for two wheels. This is for the 9 inch drum brakes commonly found on the early 6 cylinder cars with 7-1/4 inch rear ends.*Note - Kit does not include hardware for rear emergency brakes.

C9OZ-2211-C Right hand rear brake backing plate for use with 1-3/4 inch wide brake shoes. Clean Western part with no heavy corrosion like you see on Eastern cars. Inspected for excessive wear. Also used on 6 cyl and 302 Mustangs in 69-71. Used on cars with 10" drums.Originally manufactured by Kelsey-Hayes, KH part number 70866. Originally manufactured by Bendix part number 319481.

C9OZ-2212-C Left hand rear brake backing plate for use with 1-3/4 inch wide brake shoes. Clean Western part with no heavy corrosion like you see on Eastern cars. Inspected for excessive wear. Also used on 6 cyl and 302 Mustangs in 69-71. Used on cars with 10" drums.Originally manufactured by Kelsey-Hayes, KH part number 70867. Originally manufactured by Bendix part number 319480.

C3OZ-1126-B Used brake drum with the vintage casting look. Guaranteed to successfully be turned and not exceed the manufacturers inside maximum of 10.060". When we say the "vintage casting look", we mean with the proper groove and contours. Reproductions are fine, but do not retain the casting design of the original casting company. When looking for used brake drums, the rule of thumb is to find ones with a brake surface area of 1/4 inch more than the brake shoe width.

C9OZ-2211-B Right hand rear brake backing plate for use with 2 inch wide brake shoes. Clean Western part with no heavy corrosion like you see on Eastern cars. Inspected for excessive wear. Used on cars with 10" drums.Originally manufactured by Kelsey-Hayes, KH part number 71085. Originally manufactured by Bendix, part number 317559.

C9OZ-2212-B Left hand rear brake backing plate for use with 2 inch wide brake shoes. Clean Western part with no heavy corrosion like you see on Eastern cars. Inspected for excessive wear. Used on cars with 10" drums.Originally manufactured by Kelsey-Hayes, KH part number 71086. Originally manufactured by Bendix, part number 317558..

Used brake shoe guide plate, or anchor pin, that holds the top of the drum brake shoes together on your Mercury Cougar or Ford Mustang equipped with drum brakes. For the money our reproduction plate is a better value and cleaner, too. These have 1/2 inch holes in them.Replaces Ford part number C4UZ-2028-A.

Used brake shoe guide plate, or anchor pin, that holds the top of the drum brake shoes together on your Mercury Cougar or Ford Mustang equipped with drum brakes. For the money our reproduction plate is a better value and cleaner, too. These have 1/2 inch holes in them.Replaces Ford part number C4UZ-2028-A.

Used hairpin clip for attaching the brake light switch to the brake pedal. This clip was also used to attach the clutch rod to the clutch pedal on manual transmission cars. Fits all years 1967-73, Ford and Mercury.Ford Part # 380699-S

Reproduction brake light switch for Mercury Cougars and Ford Mustangs equipped with manual brakes. Ford originally called these stop lamp switches.Replaces Ford Part #: C9ZZ-13480-A.

Pair of reproduction firewall to shock tower braces for the Mercury Cougar. These are good quality reproductions that are already painted black so the only thing you need to do is bolt them on.Replaces Ford part #'s C7ZZ-16A053 driver side (left hand), C7ZZ-16A052 passenger side (right hand).

Steel tubing features tin/lead coating and plated zinc chromate fitting and are exact copies of the originals with color coded fittings like original. This set is correct for both power and manual drum brakes. As original, they have an extra "coil" of tubing that is unwound and stretched when used with a power brake booster.

Reproduction passenger side (right hand) outer frame rail patch for Mercury Cougar or Ford Mustang.Here's our little film to help you fortify your flexxy feline!

Reproduction passenger side (right hand) torque box outer section for Mercury Cougar and Ford Mustang coupe and convertible.Here's our little film to help you fortify your flexxy feline!

Full passenger (right hand) side front frame rail that measures 52" long and the outer rail has weld nuts installed for proper installation. Fits: 1967 Mercury Cougar1968 Mercury Cougar1969 Mercury Cougar1970 Mercury Cougar 1967 Ford Mustang1968 Ford Mustang1969 Ford Mustang1970 Ford Mustang ...

Full passenger (right hand) side front frame rail that measures 52" long. Fits: 1967 Mercury Cougar1968 Mercury Cougar1969 Mercury Cougar1970 Mercury Cougar 1967 Ford Mustang1968 Ford Mustang1969 Ford Mustang1970 Ford Mustang ...

New pair of white and yellow paint sticks for the Mercury or Ford. These units were used by FORD at the assembly plants to mark fender aprons

Reproduction shock tower and apron assembly  for your Cat or Pony.Here's a little film to help you fortify your flexxy feline!

Universal driver side (left hand) or passenger side (right hand) inner floor frame patch that you can trim to fit the area that needs to be repaired.

Reproduction driver side (left hand) outer front frame patch for Mercury Cougar and Ford Mustang.Here's our little film to help you fortify your flexxy feline!

Full driver (left hand) side front frame rail that measures 52" long. Fits: 1967 Mercury Cougar1968 Mercury Cougar1969 Mercury Cougar1970 Mercury Cougar 1967 Ford Mustang1968 Ford Mustang1969 Ford Mustang1970 Ford Mustang ...

New inner floor frame support for the Mercury Cougar and Ford Mustang.

Here is our reproduction SPI torque box for the driver side (left hand) of your Mercury Cougar coupe.

Here is our reproduction passenger side (right hand) SPI torque box for your Mercury Cougar coupe.

Reproduction inner floor frame rail patch for the Mercury Cougar and Ford Mustang coupe and convertible. As this item is for a Mustang, you will find that you will have to modify it to work with your Cougar. This unit measures 28" long where the Cougar piece is 19". This unit is a 1/4" wider than the Cougar piece as well.

* This is the closest available fit full floor pan for the 1969-73 Ford Mustang Convertible or Mercury Cougar Convertible, this pan will need modification to "make it fit." Complete floor pan for the 1969 - 72 Mercury Cougar or 1965-68* Ford Mustang Convertible. This item ships direct from the manufacturer for most orders and must be shipped via truck freight, and CANNOT ship via UPS. Shipping to business addresses tends to be less than residential addresses, sometimes substantially....

Now you can replace this original part, which is commonly stripped out, with a nice reproduction. Must be welded to floor pan. 6 total per car, 2 inboard in the transmission tunnel, and 4 on the rear seat pans. The front outboard anchors are part of the rocker rails. Rectangular shaped like the 1967-73 cars. We have noticed that the last generation 1971-73 Cougars had 4 round shaped plates in the rear floors. Same threads, all work the same. These were pretty much used on all Ford...

Passenger side (right hand) front seat floor pan. This pan is cut from the full floor pans in order to save on shipping costs when a customer does not need the entire length pan. Cutting from the Dynacorn full length pans means this will be a quality cut, when compared to other pans on the market.   1967-68 style ribbing, works in 1969-70 and can be modified to fit 1971-73. *NOTE* This floor pan has the outside lip bent down which is proper for coupes, convertibles were bent up....

Must have for 69-70 convertible owners or anyone else who wishes to tighten up the notoriously weak front inner structure of the 67-70 Cougar / Mustang. All three of these easy to install upgrades are outlined in the BOSS 302 Chassis Modification book that is NOT included in this package. After you install this kit you will wonder how you could have possibly lived this long without it. Even if you already have the one piece export brace, the chances are it is the old ill fitting off-shore...

Detachable mounting plate for installing the passenger side convertible ram cylinder, to the convertible top frame assembly behind the quarter interior panel. Right and left are the different, fits all 1969-70 Mercury Cougar and 1965-70 Ford Mustang convertibles. Ford part number C5ZZ-76531A18-A.

This original part has been reinforced to brace the front frame rails / tie together lower control arm pivots in a superior way to the original design. This design will prevent any camber change in hard cornering. This is not needed for the average Cougar owner but if you are desiring to make your car a "Handling Machine" every bit counts and this is an inexpensive upgrade. These crossmembers are welded in house, and will be unpainted bare metal. This combined with our shock tower...

New coil spring compressing tool to compress the coil springs of the 1967-73 Mercury Cougar or 1965-73 Ford Mustang. This tool now comes with a bearing to make the job much easier. This spring compressor is a must for safely removing front coil springs. We also offer a 60 Day Loaner if you only need the tool for a short period of time. *NOTE* Not recommended for heavy duty coil springs like found on pickup trucks and full sized cars. ...

Service replacement NOS passenger side hood hinge for Mercury Cougar and Ford Mustangs. 1978 manufactured date, this one is painted a gloss black color. New old stock hood hinge less spring. These hinges will work on 1970 Cougars, but because the grill center is attached to the hood during that year. The hood hinge requires heavier duty springs to accommodate the additional weight on the hood.Ford part # C5AZ-16796-B, C8AZ-16796-A, and C9AZ-16796-A.Anghel Restorations offers a very detailed...

Service replacement NOS passenger side hood hinge for Mercury Cougar and Ford Mustangs. Painted a satin black color. New old stock hood hinge without the spring. These hinges will work for 1970 Cougars, but because the grill center was attached to the hood during this year. The spring is heavier duty than 1967-69.Ford part # C5AZ-16797-B, C8AZ-16797-A, or C9AZ-16797-A.Anghel Restorations offers a very detailed breakdown of the differences in the Cougar and Mustang hood hinges. ...

If you are not looking to match the part numbers of your original hinges, we recommend considering our PREMIUM quality reproduction that is made of thicker material than the originals for added durability and is far superior to any previous reproduction. This listing is for you folks out there who want the correct part number on your hinge. Good used OEM original hood hinges that are available individually or as a set.   We carefully inspect these hinges before sending them...

C5ZZ-7610962-A Ford description of this plate is "Plate - Front floor lower cross member". All 1967-73 Cougar convertibles and all 1965-73 Ford Mustang convertibles use this plate. Bolts into place with 6 hex bolts 3/8-16 x 1-1/8" with washers. These were painted satin black from the factory. As you look at our picture below you will see the repro is about half the thickness. The repro is different in every detail but will work. We also have used plates with minor damage at a reduced cost.

If you are not looking to match the part numbers of your original hinges, we recommend considering our PREMIUM quality reproduction that is made of thicker material than the originals for added durability and is far superior to any previous reproduction. This listing is for you folks out there who want the correct part number on your hinge. Good used OEM original hood hinges that are available individually or as a set.   We carefully inspect these hinges before sending them...

Rechromed GT air cleaner lid for the Mercury Cougar and Ford Mustang equipped with either the Boss 302, GT 390, or 428 CJ engine without the shaker option. It was possible to order a 390 GT motor for your Cougar without ordering the 390 GT package. Cougars equipped with the S code 390 6.5 Litre engine, that did not come with the GT package, would have used the painted air cleaner lid. Replaces Ford part # C7OZ-9661-A.*NOTE* The outside dimension of the lid is 16.75 inches and will not fit the...

Fits all V8s with oval air cleaner.

This wheel is inspired by the 1966 Shelby GT350 10 spoke alloy wheel. This updated design was created using state of the art casting technology for superior strength and precision. Each wheel features a CNC machined face with gloss black accents and a clear coat finish. These wheels take a specific shouldered 3/4" lug nut, find them here. These wheels come with free chromed plastic center caps. The caps have a red Legendary logo but we can include at no cost, a set of black and chrome walking...

Silicone and fasteners, everything needed for installation of our seat divider panel.

Great investment considering how easy it is to mar your switch, bezel or dash paint when trying to remove your ignition switch bezel with a hammer and screw driver. Black, basic handle tool removes and installs headlight switch bezels. When coupled with ignition bezel tool it removes and installs ignition switch bezels on any 1967-68 Mercury Cougar and Ford Mustang. A 5/32" Allen wrench is needed to attach tools together. Allen wrench included.  ...

Great investment considering how easy it is to mar your switch, bezel or dash paint when trying to remove your ignition switch bezel with a hammer and screw driver. Black, basic handle tool removes and installs headlight switch bezels on any 1967-70 Mercury Cougar or Ford Mustang. Additionally, it also removes the wiper switch on 1969-70 Mercury Cougar and Ford Mustang. When coupled with ignition bezel tool it removes and installs ignition switch bezels on any 1967-68, or 1969...

Clever tool that keeps the piston stationary in your brake distribution block. It is as simple as centering the piston and screwing in this tool, of course your have to catch the groove in the piston. Leave in until brakes are completely bled and functioning. Remove and install your brake warning light switch.

The Hustler Stick features heavy-duty 1-1/4" diameter tubing, and is an alignment bar designed for bumpers, hoods, decks, panels etc. Made in the USA, it has a 1/4", 6 foot long chain with hooks at each end. This versatile tool is very useful in shaping damages on a vehicle body. To use it, hook it up to the panel or bumper, anchor the stick properly, and pull it by hand.We will loan this hustler stick for 60 days, with a 100% refundable purchase price. Tool must be returned in undamaged...

New RTV  oil resistant, high temperature, Ultra Black gasket maker for use on the Mercury or Ford. It's no mistake that Ultra Black has become an automotive industry standard. It's low odor, flexible, non-corrosive, vibration resistant, oil resistant, heat resistant, fast curing formula cannot be beat. Great for use on any surface that experiences high heat and oil like the valve cover gaskets.

Great investment considering how easy it is to mar your switch, bezel or dash paint when trying to remove your ignition switch bezel with a hammer and screw driver. We also have a handmade version of this same tool for a lower price.

Hard to find pair. This letter series would have been issued in 1968-1969. This particular pair could use a bit of restoring to get back to perfect condition, but they are in good shape and will not have any extra holes like the grade B plates do.   NOTE:  "Due to programming limitations, a license plate that still has a record on the database cannot be reassigned. Therefore, customers returning to California after registering their vehicle out of state cannot have their old...

New adhesive / epoxy applicator to apply our 3M window adhesive to the glass (or whatever else needs bonding) in your Mercury or Ford. This non-drip unit features an easy loading breech, a 1:1 mixing ratio and full cartridge support. We also offer a 60 day loaner if you only need this unit for a short time. ...

We will loan you this adhesive / epoxy applicator for 60 days, with a 100% refundable purchase price. Only available to customers that purchase our 3M bonding adhesive. Tool must be returned in undamaged condition with no missing parts within the 60 day time period.Returns past 60 days are subject to a 25% restocking fee. ...

Grade A used passenger side air conditioning vent register for 1967 Ford Mustang with standard (non-deluxe) interiors. This one has the factory pebble grain or camera case finish. Very nice used, only have the one available. We also have several Mustang center vents available with the pebble graining.Replaces Ford part number C7ZA-19893. This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store...

Tested and working OEM Ford Mustang AM radio. Part number 7TPZ. Tiny crack in the face plate as shown, and the speaker wire connector is missing. Main power wire connector is perfect, nice chrome on the buttons.

New intake manifold that has never been used, but it's missing the packaging, so we're calling it an "out of box special". Port size is for the 2V cylinder heads. Perfect for adding a 4 barrel carburetor to a stock 351 Cleveland 2V engine.

Grade A used A/C center vent for any 1967-68 Ford Mustang. Grade A will be nearly defect free, may have some small blemish on the thin vertical chrome by the pebble graining.Replaces Ford number C7ZA-19623.

Grade B used A/C center vent for any 1967-68 Ford Mustang. Grade B will have a defect or two in the chrome plating.Replaces Ford number C7ZA-19623.

Reproduction pinion seal for the 9 inch ring gear on the 1967 - 1973 Mercury Cougar or Ford mustang. 

Hard to find pair. This letter series would have been issued in 1968-1969. This particular pair has extra holes drilled, which would need to be repaired (see pictures). They could be restored or used as-is. Because of this, we're selling them at a reduced price. NOTE: "Due to programming limitations, a license plate that still has a record on the database cannot be reassigned. Therefore, customers returning to California after registering their vehicle out of state cannot have their old...

It is not often we get perfect used but nothing fits like OEM!The Engineering number on the bottom of the passenger side reads C7ZB-6521448-ACheck out our video below for helpful tips on disassembling your vent and quarter windows: 67-68 Cougar/Mustang Vent & Quarter Windows - Disassembly for Restoration

Original NOS part, new in box. Ford part # C5ZZ-6503110-A

Reproduction gas tank to filler pipe hose fits the 67 to 70 Mercury Cougar, measures 4 1/2" long. Excludes 1970 with California emissions. Even if yours is not cracked it will be hard if it is over two decades old. We highly suggest you replace this part if yours is in fact hardened with age because a minor rear end collision could cause it to fail and send fuel spilling into your trunk area. Replaces Ford part #: C8ZA-9047-A.

NOS lower inside door seal for any 1967-68 Mercury Cougar or Ford Mustang. No wrapper, this is not a reproduced item. Not very many Cougars or Mustangs came with this seal, we think it may have been for wind noise? Unknown. These are pre-drilled for mounting, no hardware included.Replaces Ford part number C7WY-6520272-A.

These vertical seals attach to the leading edge of the rear quarter windows and seal against the rear edge of the door glass. Sold as a pair.Replaces Ford Part #: C5ZZ-6530146 and C5ZZ-6530147. These are the premium or concours versions. We also sell economy versions.

New and improved reproduction bottom of the door seal for the 1967 - 1970 Mercury Cougar or Ford Mustang. Unlike previous versions, these are now made with denser material and are much more rigid. They measure 38" for 1967 -1968 and 41" for 1969-70 so you will have to trim them down if you have a 1967-68. One of the most common missing parts on a 1967-70 Mustang or Cougar today is the lower weatherstrip seals on the doors. These seals were added to cars to keep dirt and moisture from entering...

Complete foam seal kit for the heater box, flappers, evaporator and heater core on a '67-'68 Cougar or Mustang with factory Air Conditioning. This kit is almost always needed when replacing your heater core.Replaces Ford part #: C7ZZ-18500-A. Check out our video below on how to replace a heater core on a '68 Cougar with A/C! This seal kit is an integral part of the process. ...

New rubber body plug, fits oval rear shock access hole. 1-3/4" x 3-5/16" oval holes. Sold individually, Usually 2 per car. Fits 1967-70 Mercury Cougar and Ford Mustang.Replaces Ford plugs marked 378923-S.