1967 Ford Mustang

Hard to find pair. This letter series would have been issued in 1968-1969. This particular pair has extra holes drilled, which would need to be repaired (see pictures). They could be restored or used as-is. Because of this, we're selling them at a reduced price. NOTE: "Due to programming limitations, a license plate that still has a record on the database cannot be reassigned. Therefore, customers returning to California after registering their vehicle out of state cannot have their old...

This used assembly includes lamp socket, bracket, mercury switch, and length of wire.Replaces part # C7ZB-15702-A

Available in original blue light diffusers or custom red or yellow for a brighter "custom" look. Please note that depending on the options you have, there are different numbers of diffusers (filters) needed for different years and models. Sold as a set of four. SOLD AS SET OF FOUR(4).67 - 68 Cougar Uses6 - Instrument Cluster (XR7 or Standard) 2 - Clock (XR7) 2 - Oil Pressure Gauge (XR7)69 - 70 Cougar Uses5 - Instrument Cluster (XR7 or Standard) 2 - Clock (XR7) ...

Used Link for 1967-68 Mercury Cougar and Ford Mustang with speed control. The Link is a tubular shaft for the Rod. It attaches to the Trunnion. Ford part number C7ZZ-9D768-A.

Used wheel cylinder link pin. This pin protrudes from both ends of the wheel cylinder and are responsible for moving the brake shoe in and out when pressure is applied as well as keeping the brake shoe in place. Fits all drum brake wheel cylinders, front or rear drum brake systems. Two needed per wheel cylinder. Sold individuallyFord part number B7A-2042-A.

NOTE: WE SUGGEST LOCAL PICK UP ONLY FOR CORE ENGINE BLOCKS BECAUSE WE CANNOT GUARANTEE BLOCKS WILL NOT HAVE CRACKS INTERNALLY. Long block, factory A code 289-4V V-8 engine. Rated at 225 Hp with 9.8:1 compression ratio in 1967. Not standard bore engine block, that may or may not have been in running condition when pulled. May or may not have 9.8:1 pistons. Guaranteed to be rebuildable. Complete engine less carburetor, distributor, exhaust manifolds, fan, accessories, pulleys, and flex plate....

Set of two polyurethane bushings that insert into the rear side of the lower control arm. This set contains two bushings that measure 1 7/16 across the leading inside edge, and 1 5/8 across the outer rim. Typically these bushings fit Ford factory installed lower control arms with the welded on jacking tabs. Note: These smaller diameter bushings were used on factory installed control arms. Service replacement control arms utilized 1-9/16 inch bushings.

Rare find, must have for your Concours Cougar. Sold individually.Ford part number C5ZZ-1012-BFits the following models with Styled steel wheels:1967 Mercury Cougar1968 Mercury Cougar1969 Mercury Cougar1970 Mercury Cougar1967 Ford Mustang1968 Ford Mustang1969 Ford Mustang1970 Ford Mustang

Reproduction GOLD HAZE lug nut cover deigned to fit the Cobra / Eleanor style Legendary LW90 wheel.  Sold as a set of 4 and includes 20 Legendary low profile lug nuts.

Nice used original Rotunda, over the counter dealer accessory. Stainless steel construction, weighs just under 8 pounds with hardware. Actual dimensions are 20 1/2 inches wide, 48 1/2 inches long, and the back lip is 3 inches tall. Installation hole spacing is as follows. Rear spacing 47-11/16" on center, front spacing (nearest the rear window) is 47-9/16". The spacing on short sides are 18-3/4" on center. This rack was utilized for may years on many cars. The same company made them for...

NOTE! These wheels are intended to be balanced with a lugcentric adapter. They will not balance with a traditional cone spacer on the tire spin balancer. Many tire shops do not deal with classics and do not have the right attachment. If you attempt to balance these wheels without the correct adapter, they will resemble a bent wheel. Unfortunately, we no longer carry the US made version of these, as the manufacturer was bought out several times and with each successive owner the quality control...

New aluminum 17x7" Magnum 500 wheel for your Mercury Cougar or Ford Mustang. A great way to reduce the un-sprung weight on your Cat or Pony and look great while doing it!  This item also includes a center cap, but they are a cheap plastic chromed cap with a blacked out center.  We recommend using the adapter plates and Magnum 500 center caps we sell from Scott Drake. Lug nuts sold separately, get them here. ...