1967 Ford Mustang

Reproduction alternator wiring harness for all 1967 Mercury Cougar Standard Models, meaning Non XR7. Additionally 1967 Ford Mustang with tachometer. Excellent reproduction copied from an NOS wiring harness.Ford service number C7ZZ-14305-E, wire harness marked C7ZB-14305-E.

Used intake manifold Edelbrock model 2755 Torker 289. Fits Ford 289 or 302 engines 1965-73. Check the small block Ford forums for fitment under the hood. Check the Edelbrock specifications on the Interweb. Good condition, no damaged threads or cracks noticed. 

NOS three part, telescoping, round base antenna. Comes with round ridged base gasket.  NOTE: Only one of these antennas (pictured) is in the original box, the others are in brown bags with labels. Once the first has shipped, the others will ship without the original Ford box. *Customer Feedback* "Aloha Don, The antenna showed up with the rest of the USPS sent items. Got in here in three days. Point of installation of antenna. Tie a string to the plug side of the antenna assembly...

Reproduction apron nuts for the 67 - 70 Cougar or Mustang. These are the fasteners that are imbedded into the aprons on either side of the engine compartment and are used to fasten the hood hinges to the car. Sold in a pack of 6 fasteners.

Pressure die cast, with quality chrome sun visor center bracket and rear view mirror mount. Replaces one of the most visible interior parts on a 1967 Mustang or Cougar. Break away style, two piece construction. Beware of cheap single piece imitations that are available as they are unsafe. Keep in mind you will have to give your screw driver some good pressure when installing to make the mirror fit tight. Replaces Ford part # C7ZZ-17690-A. These are manufactured in the USA. ...

NOTE! When we ship a rear end, we will remove the third member and ship it in a separate box. Some assembly will be required. Housing overall width - 54-1/4 inches flange to flange. Overall width measured from faces of axles, not the tips. All 1967-70 have the same overall width of 59-1/2 inches. Spring perches are 43 inches apart on center. Complete rear end housing - drum to drum, with axles, and with pumpkin. 1967 EARLY 8 inch rear end housings with fill plug in the steel housing as seen...

NOTE! When we ship a rear end, we will remove the third member and ship it in a separate box. Some assembly will be required. Rear axle assembly - Housing, Axles, brake backing plates, and third member. Housing overall width - 54-1/4 inches flange to flange. Spring perches are 43 inches apart on center. 1967 early 9 inch rear end housings had the carry over fill plug in the steel housing as seen from the back of the car. As removed from West Coast Cougar organ donor car. We recommend a bearing...

Original New Old Stock NOS reverse light lenses. Sold as a pair, includes screws!Ford Part number C5ZZ-15514-A.

Correct for closed emission system Cougars sold only in California. Air cleaner base for both the 289-2V and 289-4V engines. About 17.25" inches in diameter. California emissions with the metal elbow for hose connection to the oil filler cap.

Factory air cleaner base the all S code 1967 Mercury Cougar non-GT or the 6.5 Liter option, 1967 Mustang 390-4V without the GT option, and 1967 Ford Thunderbird with Z code 390-4V or Q code 428-4V engines. California emissions version which has the closed emissions. Note the elbow on the side which attaches with a hose to the oil fill cap.This is the one everyone uses to make a correct 1969-70 428 Cobra Jet ram air or 1967 GT air cleaner base . This basic bowl design was used by the Ford...

Reproduction group 27 battery heat shield that fits many Mercury Cougar and Ford Mustang applications from 1967-70, on most hi-performance engines. It was often the first part discarded but serves a real purpose. Nice American made part, stamped with Ford numbers C7ZB10A682B and C7OB10A682B. There is also a D0... sized for group 24 heat shield offered for 1970-73. *Trivia - these battery heat shields were often trimmed down to fit group 24 batteries.Click on the link below to find some...

This battery cover is designed to be used with any maintenance free flat top battery **24/60 series with original terminal location for the Autolite battery covers.