1968 Mercury Cougar

New Old Stock wiper switch for 1968 Mercury Cougar XR7 models. Uses a larger knob with an allen set screw to hold it in place. Knob sold separately. Keep your old knob. Ford part numbers: C8WB-17A553-B and C8WY-17A553-B

NOS switch and bracket for the emergency / parking brake. Standard switch found on 1967-68 Mercury Cougar XR7 models. Optional on Cougar standard model 65A and 65C, also optional on Ford Mustang. Clamps to the hand parking brake assembly. Ford part number C7ZZ-15A851-A

T5 TRANSMISSION INFORMATIONFor any and all questions or technical support for this transmission or its installation, please call Kevin Classics 510-708-1136. THIS TRANSMISSION HAS NO OIL IN IT! Do not use gear oil in this transmission! Use about 3 quarts of Dextron III automatic transmission fluid only! This is a world-class T5 1987- 1993 type that is the correct length input shaft for the 67 - 73 Cougar or Mustang conversion. Features:Rebuilt by an ASE-certified mechanic who...

Mini Tachometer that fits in the small center clock opening. This easy to install three wire tachometer looks OEM but as you probably know, Mercury never offered an in dash tachometer from the factory. Just remove your current clock or dummy plate and this unit installs from the backside in its place. If you are returning a core dummy plate for credit it must have good cosmetic appearance. When you send your core for credit, please be sure to include a copy of your sales receipt. Check out the...

Good used pair of taillights that includes two average grade "B" bezels and two used grade "B" lenses with backing plates. No obvious cracks in the lenses but there will be stress cracks that will only be found under close inspection. The bezels will have good chrome with no obvious defects but the paint will need attention. This is a good saving over buying the four or six parts individually. Don't forget to pick up a set of gaskets for the lenses as they always are needed after 40 plus...

1968 XR7 and standard Cougars use the same rear wiring harness to the taillights. This is a grade "A" premium grade harness that is not sun damaged, spliced, or damaged in anyway. XR7 and Standard Cougars use the same rear wiring harness to the taillights, only the sub-harness that connects to it that runs along the underside of the package tray and down to the fuel sending unit differs XR7 vs. Standard. The major difference is that the xr7 utilizes a two wire plug and the Standard Cougar uses...

Used Grille headlight Eyelid Tension Spring for the 1967 and 1968 Mercury Cougar. These tension springs are located on either side of your hidden headlamp eyelids. Sold individually, 4 needed per car. Ford part # C7WY-13A163-A. Check out this video Check out this video

This tiny little spring has a diameter no larger than a pencil. Its function is to attach the deck lock cover to the deck lock housing and to keep the deck lock cover closed. This is a unique spring to this application and rather hard to find. Check out this video

Reproduction aluminum cast A356 water neck for FE Big Block engines. Made from original factory blueprint, and includes the correct stamping. Will fit the 67 Big Block, but markings are correct for 68. Replaces Ford Part #: C8AE-8592-B.

This rare accessory was only offered over the counter, it was not available as a factory option. Great upgrade for the 1970-1973 Cougar owner as cruise control was discontinued after 1969 and not offered again until 1974 on the Mercury Cougar.Ford part number C8OZ-9B742-AClick on images to enlarge. ...

Neat detail item, stamped steel with zinc plating. Mounts on intake manifold and holds one end of the accelerator linkage spring for the 289 / 302.

Metal rod that hooks to the carburetor linkage and the accelerator pedal bellcrank, or shaft. Rod measures 12.66 inches long. Application 1968 Mercury Cougar and Ford Mustang  with 289 or 302 engines and cruise or speed control. Ford part number C8ZZ-9A702-C. Hooked end goes into the carburetor linkage, threaded end to the rear. A rod end clevis clip is needed for attachment to the carburetor – see part B7A-9826-A. *Note – for use with factory cruise control.