1967 Mercury Cougar

This stepped window trim clip is great for times when your stainless trim just will not click into place. We have found that the reproduction cougar rear window gasket is a little taller than OEM and this adjustable clip allows you to compensate. Another instance this multi-fit clip works is when someone has replaced one or more nail-heads that the clip fastens to and located them in the wrong place.Sold Individually.These clips attach to posts built in to the car. In case you're missing some...

The Proper ignition advance curve is vital for maximum performance, economy (gas mileage) and drive-ability. Ford / Mercury owners had few acceptable choices with regard to adjusting the vacuum curve with their OEM distributor. You could fumble with the stock washers, fiber stops and springs (a hit-or-miss exercise in frustration!) or you could spend the money on an adjustable after market vacuum advance that looks completely out of place and cost you major judging points. This works on any...

Economy Small Block Powering Steering Adjustment Bracket. Lighter weight material than OEM. Replaces Ford Part #: C7SZ-3A732-A.

Perfect fit for your 289, 302, or 351w with or without AC but a hard sell when our good used rust free brackets cost less . . .

Used alternator adjusting bracket for early 1967 Mercury Cougar or 1965-67 Ford Mustang with 289 V-8 engines. Very early style which is a carryover from the 1965-66 289 alternator bracket. The difference of this C5AE-10145-A alternator bracket and the C7OE-10145-A bracket is the C7OE bracket has a slightly rounded off end to prevent contact with some of the larger diameter water pump pulleys. To be safe, we recommend the C7OE-10145-A bracket for clearance purposes. Ford part number...

Used alternator adjusting bracket for any 1967-68 Mercury Cougar or 1967-68 Ford Mustang with 289 or 302 V-8 engines. C7OE-10145-A stamped bracket has a slightly rounded off end to prevent contact with some of the larger diameter water pump pulleys from previous years. Ford part number C7OE-10145-A.*Trivia - All 3 small block alternator adjusting brackets from 1965-1969 will fit most all 289 / 302 / 351W engines unless your engine has one of the larger pulleys. ...

Used alternator adjusting bracket for any 1967 Mercury Cougar or Ford Mustang with 390 engine and without smog. Also fits Shelby GT-500.Replaces Ford part number C6AE-10145-B, or it is stamped C6AE-B

Application is 1967 - 1968 289/302 and 1969 Boss 302 Eliminator alternator adjusting with factory air injection emissions. Casting number C6OE-10145-A, Ford part number C6OZ-10145-A.

Application is 1967 390 with California emissions. Casting number C6AE-10145-A. Ford part number C6AZ-10145-A.

This high performance alignment kit replaces the factory eccentric bolt and cam that holds the lower control arm to the frame.  The eccentric cam is used for setting wheel camber. When the eccentric is turned, the lower arm moves in or out changing camber. Stock eccentric cams can slip or rotate going over bumps, allowing the alignment to change. Which is the cause of many worn tires. The lower control arm adjusting cam eliminator kit replaces the eccentric bolt and cam with non slipping...

Sleeve and hardware for joining the inner and outer tie rods together. This also is a 'toe in' adjustment part. Sold individually, two needed per car. Replaces Ford Part #: C2AA-3310-A

Set of 8 1969-1970 Headlamp adjusting screw. Two per bulb, eight in all per car, comes with two new mounting screws. This part is identified by the clipped corners. Also used during 1967 and 1968 on a limited basis. Will be in good rust free condition as we only keep the best examples. Also sold individually.