All Available Parts - 1969 Mercury Cougar

Big Block FE 390 or 428 engine feed harness that fits the 1969 or 1970 Mercury Cougar and Ford Mustang. Replaces Ford Part #: C9ZZ-14289-B and D0AZ-14289-A.Check out the video below on our new gauge tester: ...

Air Conditioning Clutch Feed Wire that runs along the driver side valve cover to the clutch on the compressor. 24 inches in total length. Starting in 1969 the female plug was of the water proof variety. Black plugs on either end. Replaces Ford Part #: C9ZB-19A885-B.

Air Conditioning Clutch Feed Wire that runs along the driver side valve cover to the clutch on the compressor. About 24 inches in total length. Starting in 1969 the female plug was of the water proof variety. Black plugs on either end.

Reproduction dash to engine gauge feed harness for the Mercury Cougar equipped with the 351 Windsor. All black and yellow boot plugs, this is the style used on cars without air conditioning. Fits 1969-70 Mercury Cougar with 351W engines and 1969-70 Ford Mustang with 302 or 351W engines. Check out the video below on our new gauge tester: ...

Used standard grade "B" main under hood wiring harness located in the engine compartment. This harness has plugs for head lights, voltage regulator, starter solenoid, windshield washer pump, and horns. All electrical harnesses are inspected, professionally repaired, tested, and ready to install. Grade "B" harnesses may have one or two repairs where grade "A" harnesses will be rare uncut beauties. 1969 Mercury Cougar Standard models and Ford Mustang with AMP warning light. Not compatible with...

Grade "A" used harness with no cuts or splices. Correct for XR7, Eliminator, and 1969-70 Shelby Mustang GT-350 and GT-500. Ford part # C9WY-14405-B.*NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's and is the designer of all of our solid state sequential systems. There is no question he cannot answer! Here is a link to a great source of information on the subject. ...

3/4" wide and 60' long. This tape resembles the tape you would find on bicycle handle bars or a hockey stick but is in fact different. The taillight harness uses this type of tape as well as portions of the under dash harness. Not used in modern applications and getting rather hard to find these days.NOTE: This is FRICTION tape not adhesive tape. It is coated with rubber and relies on friction with itself to wrap wires. It does not stick to the wires. This was one of the first types of...

Reproduction under hood wiring harness located in the engine compartment. This harness has plugs for head lights, voltage regulator, starter solenoid, windshield washer pump, and horns. 1969 Mercury Cougar Standard models and Ford Mustang with AMP warning light. Not compatible with XR7 model Cougar or Mustang with Ammeter. Replaces Ford part # C9ZZ-14290-R. Fits: 1969 Mercury Cougar Standard 1969 Ford Mustang ...

Used grade "B" under dash wiring harness with a black plug end for the standard Mercury Cougar with air coniditoning. Mercury used either a black or white plug end for the under dash harness during the 1969 model year run. If you have a blue printed circuit board, then this is the unit you need. All electrical harnesses are inspected, professionally repaired, tested, and ready to install. *NOTE* Excludes Eliminator - see 1969 XR7. If you send us your old used under dash harness, you will...

Grade B 1969 Standard Model Cougar, under dash harness without air conditioning, black plug. Used grade "B" under dash wiring harness for the standard Mercury Cougar. Mercury used either a black or white plug end for the under dash harness during the 1969 model year run. If you have a blue printed circuit board, then this is the unit you need. All electrical harnesses are inspected, professionally repaired, tested, and ready to install. *NOTE* Excludes Eliminator - see 1969 XR7. If you send us...

Grade A used under dash wiring harness for Standard Model 1969 Cougars without air conditioning. Used grade "A" under dash wiring harness for the standard Mercury Cougar. Mercury used either a black or white plug end during the 1969 model year run. If you have a blue printed circuit board, this is the unit you need. All electrical harnesses are inspected, repaired, tested, and ready to install. *NOTE* Excludes Eliminator - see 1969 XR7. If you send us your old used under dash harness, you will...

Wiring pigtail that runs from the main 14401 under dash harness to the neutral safety switch on the 1969 Cougar.

Used wiring pigtail that runs from the 14401 main under dash wiring harness to the wiper motor.

Used emergency brake warning light harness that runs from the 14401 main under dash harness to the warning light panel in the center of the dash on the STANDARD 69 - 70 Cougar. This warning light harness uses the 257 bulb which you can find here.You can find the other convenience light harness / sockets here. Ford part number C9WB-15883-B ...

Brake switch jumper wire, 4 inch long extension. Bridges the under dash wiring harness and the brake light switch. Not used on many cars, we suspect that it was used on the assembly line when the brake switch plug didn't reach the brake switch. Adding one of these jumpers, saved time from re-routing the under dash wiring harness. This jumper can also be used to repair bad stop light connectors on 1967-70 Cougars and Mustangs (and other Fords) by cutting off the male end and splicing it...

Used grade A used under dash wiring harness for Standard Late Model 1969 Cougars without air conditioning. Mercury used either a black or white plug end during the 1969 model year run. If you have a red printed circuit board, this is the unit you need. All electrical harnesses are inspected, repaired, tested, and ready to install. *NOTE* Excludes Eliminator - see 1969 XR7. If you send us your old used under dash harness, you will receive an in store credit of up to $100. Also keep in mind...

Used grade B used under dash wiring harness for Standard Late Model 1969 Cougars without air conditioning. Mercury used either a black or white plug end during the 1969 model year run. If you have a red printed circuit board, this is the unit you need. All electrical harnesses are inspected, repaired, tested, and ready to install. *NOTE* Excludes Eliminator - see 1969 XR7. If you send us your old used under dash harness, you will receive an in store credit of up to $100. Also keep in mind...

This is a used grade "B" under dash wire harness that a majority of 1969 model year XR7s and Eliminators used. If you have a blue printed circuit board, this is the harness you need. If you have a red printed circuit board with a white plug, you have a late built car and need to look at our other listing. This grade "B" harness is for those of you who don't mind if the harness has been repaired. Grade B harnesses are inspected and have a couple of subtle professionally made repairs. Cars with...

Aluminum spacer used on 289/302/351 engines for mounting the alternator. Length is 1-5/8 inches long, mounts between the alternator and the cylinder head.

Used alternator adjusting bracket for any 1969 Mercury Cougar or Ford Mustang with 351W V-8 engines. This C9OE-10145-A stamped bracket is correct for all H or M code 351 Windsor engines. Will also fit 1969 F code 302 Ford engines too.Ford part number C9OE-10145-A.*Trivia - All 3 small block alternator adjusting brackets from 1965-1969 will fit most all 289 / 302 / 351W engines unless your engine has one of the larger pulleys. ...

Used alternator adjusting bracket for any 390 engine 1968-69 Mercury Cougar or Ford Mustang without factory smog. Specifically this is for 1968 390-2V or X code engines, and 1969 390-4V or 390IP engines offered in 1969 cars with S code designation. Replaces Ford part number C8AE-10145-A.This is the 411 for 1968-69 alternator mounting on Mustang and Cougar with 390 engines. If your 1968 S code car (390GT or 390-4V) was delivered in the United States (meaning not Canada or other foreign...

Used alternator mounting bracket for any 390 / 428CJ engine without smog. This is the correct bracket and was found on 1968 390-2V or X-code Mercury Cougar and Ford Mustangs. 1969 390-4V or 390IP engines in any Mercury Cougar or Ford Mustang. If you aren't a concours person or care about correctness, this alternator installation style is the cheap way to go if you aren't planning on installing the thermactor smog components. Look in the related items list for the adjusting bracket and...

Replaces Ford part number C9ZE-10A336-A. One year only Design.

One year only design. This eliminates the need for the tubular spacer, and is more sturdy. Fits any 1969 Mercury Cougar or Ford Mustang with 351W engines.Replaces Ford part number C9ZE-10A336-A.

Keep in mind that if you have the original motor mounts in your 1967 with a 289 or 1969-1970 convertible these mounts will not work. Nobody sells motor mounts for them, period. This is contrary to what every auto parts store will tell you. Your options are to purchase our (used 68-70 frame stands) or modify your existing ones.Sold individually, two required per car, left is the same as right.

Nice reproduction of an obsolete motor mount. Left is the same as right, sold individually. This isolator is used with the 390, 427, 428 and 429 Cobra Jet engines.  Sold individually. Replaces Ford Part #: D1ZZ-6038.

These Big Block motor mounts bolt to your engine block on the top side and to the motor mount (insulator) on the bottom side. These are very correct looking and fitting reproductions, much better than the $95 version you will find in most catalogs. Fits 1967-70 Mercury Cougar and Ford Mustang with 390 or 428CJ engines, will fit passenger side of 427 side oiler engine, driver side will work with modification. Original Ford part numbers C7ZZ-6046-A R.H., C7ZZ-6046-B L.H. 427 number for the left...

Factory stock for 1968 – 1970 small block V-8’s. Mounts to the frame for supporting and mounting the small block 289, 302, 351 engines. Also known as lower engine mounting brackets. We recommend this bracket for 1967 Cougars with 289. Sold in sets. Includes one each: D0ZZ-6028-C & D0ZZ-6029-C engine frame brackets. These are better quality and fit than the reproductions. *Converting to these mounts on 1967 Cougars with 289 or 1969 – 1970 convertibles with 351 allows the use of reproduction...

Mount to the frame for supporting and mounting the FE 390, 427, and 428CJ engines. Also known as lower engine mounting brackets. For all 1967 - 1970 Cougars with 390 - 427 - 428 engines. Also includes 1967 with 289. Sold in sets. Includes one each: D0ZZ-6028-D & D0ZZ-6029-D engine frame brackets.

Factory original part for all 1968 - 1970 Cougar hardtops (non-convertible) with 289, 302, and 351 engines. Right hand bracket. Ford part number D0ZZ-6028-C.

Factory original part for all 1968 - 1970 Cougar hardtops (non-convertible) with 289, 302, and 351 engines. Left hand bracket. Ford part number D0ZZ-6029-C.

Several factory applications: 1967 - 1970 big block FE or 390, 427, or 428CJ. 1967 Cougar with 289 engines. Factory original part for all 1969 - 1970 Cougar convertibles with 351 engines. Right hand bracket. Ford part number D0ZZ-6028-D. The original 1968 part number for this bracket was C8ZZ-6028-B.

Several factory applications: 1967 - 1970 big block FE or 390, 427, or 428CJ. 1967 Cougar with 289 engines. Factory original part for all 1969 - 1970 Cougar convertibles with 351 engines. Left hand bracket. Ford part number D0ZZ-6029-D. The original 1967 part number for this bracket was C7ZZ-6029-B.

Used pair of right and left engine block plates for any 1967-69 Mercury Cougar or Ford Mustang with 390 engines, or 1968-70 428 cobra jet engines. These can be made to work on a GT-E 427 if the passenger side mount is modified for clearance.Replaces Ford part number C7ZZ-6046-A  and C7ZZ-6046-B.

Reproduction pair of engine pedestals / frame brackets for the 68 - 70 small block V-8’s. Mounts to the frame for supporting and mounting the small block 289, 302, 351 engines. Also known as lower engine mounting brackets. We recommend this bracket for 1967 Cougars with 289. Sold in sets. *Converting to these mounts on 1967 Cougars with 289 or 1969 – 1970 convertibles with 351 allows the use of reproduction engine mounts.

New bolts and nuts for attaching the engine frame stands to the frame. Fits all 1967-70 Mercury Cougar and Ford Mustang with V8 engines. 4 bolts and 4 nuts. 3/8-16 X 3 1/2 Grade 5 phosphate flange bolts.

Engine mount bolt kit for installing engine or motor mounts to the frame stands. 1967-70 Mercury Cougar or Ford Mustang V-8. Two bolts and two nuts. Quality AMK part F-753.

NOS big block motor mount. Left is the same as right, sold individually. This isolator is used with the 390, 427, 428 and 429 Cobra Jet engines.  Sold individually. Ford Part #: D1ZZ-6038-A.

Factory installed, used engine mount heat shield, for any 1969-70 Boss 302 Mercury Cougar Eliminator or Ford Mustang. Mounts to the driver side mount and the asbestos portion lays under the exhaust manifold. Basic Ford part number is 6C038 for motor mount heat shields.  *Note - this item will likely not work with headers.*Note - this part does contain asbestos.

Reproduction pair of engine pedestals / frame brackets for the 67 - 70 big block V-8’s. Mounts to the frame for supporting and mounting the big block 390, 427 and 428 engines. Also known as lower engine mounting brackets. Sold as a pair.

Original FoMoCo used part in good condition. Casting number is C7AA-3A772-B. Fits both small and big block. This is really the way to go... Original OEM FoMoCo with all the right markings and about half the price or repro. Ford Part #: C7ZZ-3A732-B.

Perfect fit for your 289, 302, or 351w with or without AC but a hard sell when our good used rust free brackets cost less . . .

For 1969 351W engines only. This bracket will physically work with any 1967 - 68 289 or 302 engine, but for 1969 the bracket should not have a large stamped hole through the middle. Ford master part number C7AZ-3C511-A, same part number as the 289/302 bracket with the deletion of the large hole. Ford intended to have a casting number stamped on these brackets and it would be C7AA-3C511-C. For restoration purposes, this bracket was factory painted satin black.

Perfect fit for use with AC or non-AC 67, 68, 69, or 70 Cougar with the 390, 427, or 428 big block.

C9OZ-3C511-A Rear power steering pump support bracket. Also called the high pressure hose indexing bracket. For any 1969 Cougar or Mustang with any 302 / 351 engine. OEM used part designed to maintain the position of the high pressure power steering hose from coming in contact with with moving or high heat parts. *Note - May or may not work with non-original or replacement high pressure hoses.

Metal-stamped 1968 - 1970 Lower Radiator Mounting Brackets feature exact detail and proper fit. Painted dull black. Sold in Pairs. Rubber insulators not included. Replaces Ford part # C8ZZ-8052-A. Check out our video on Radiator and Fan upgrades below: ...

Our used lower cradle brackets for the 24" wide radiator will always have some amount of damage as shown. We will not send you mangled junk that is heavily rusted but they will require some amount of straightening due to their vulnerable location. These also work with the 67 small block and big block when putting in a 68-70 24" radiator but keep in mind the 1967 cars are not pre-drilled as are the 1968-1970 Mustang and Cougar.We are out of the 1970 style of brackets. We only have the two...

Sold as a pair, fits well into your upper radiator bracket used on 24" radiators 1967 - 1970. Replaces Ford part #: C7OZ-8124Check out our video on Radiator and Fan upgrades below: ...

Metal stamped brackets used to mount the radiator on saddle mounts styles only. Rubber insulators not included.Check out our video on Radiator and Fan upgrades below:

When you compare the originals to the reproductions you will see minor differences. This is one of the first things you look at when you open the hood of your car. For those that are looking to keep their car original, investing a little elbow grease in clean up on these used brackets is the way to go. Consider adding the upper rubber pieces to your order, see related items.These brackets came in two configurations, most has the round mounting holes but some were punched square. Not for use on...

Used on the lower mounts on the 67 - 70 big block and small block 24" wide radiator. A 1967 390 with the original radiator uses a different lower mount system which uses a different sized insulator. If you are updating your 67 with a 68 radiator you will need these. Sold as a pair. Replaces Ford part #: C8ZZ-8125. Check out our video on Radiator and Fan upgrades below: ...

BECAUSE THIS IS NOT AN ORIGINAL FORD PRODUCT, WE CANNOT RECOMMEND THIS ITEM AND NO RETURNS WILL BE ACCEPTED Shroud assembly includes custom mounting, wiring harness, and adjustable thermostat. High temperature resistant plastic with high performance electric fan to produce maximum cooling efficiency. This unit will also increased fuel economy and horsepower.  2550 CFM Fan with 30 AMP draw.  Dimensions (in inches): 15 3/4 x 26 1/2 x 3 7/8  including mounting flanges on...

C6AE-E Multiple applications over the years. 1. Later 1967 production cooling fan, generally used after 11/14/1966 on most 289 engine applications. 2. 1968 302 without air conditioning. 3. Mid year (after 11/6/1968) 1969 351 without air conditioning. 4. 1969 Early Boss 302 before 4/14/1969. 5. 1971 Cougar with 351 engine, without air conditioning. 6. **1973 Cougar 351-2V without air conditioning prior to 2/19/1973. Fan description - 4 blades and 17-1/2 inches in diameter. Ford master part...

Used in conjunction with Ford fan part # C9ZZ-8600-C that is stamped C9ZE-E. Features a parkerized shaft with an integral mounting flange. The aluminum portions are finished with silver cadmium and are mated together with filister head, Phillips machine screws (8) and an additional crimping operation was used to assemble the front and rear housings. The radial curved spring was originally finished in gold cadmium. This assembly stands 2 5/8" tall when set on its front surface, and the distance...

Another spot-on reproduction by WCCC! C9ZE-E Applications: 1. All 1969 428 Cobra Jet with and without air conditioning. 2. 1969 428 Super Cobra Jet with V code 3.91 axles only. 3. 1970 428CJ with air conditioning and some without air conditioning (see your build sheet if available). Fan description - 7 blades and 18-1/4 inches in diameter. Fan does not include thermal fan clutch. We do sell a Hayden replacement fan clutch. Replaces Ford master part number C9ZZ-8600-C. This fan will...

Closest reproduction fan clutch on the market that fits the original and reproduction C9ZE-E 7 blade power fan. Hayden fan clutch with an overall height of 2.69 inches. Similar design as originals, with thermal activated clutch. Overall diameter is 7.25 inches. The C9ZE-E 7 blade clutch fans were installed on 1969-70 Mercury Cougar and Ford Mustangs as well as 1969 Torino, Cyclone, Ranchero with 428CJ engines. Varies the fan speed with temperature of the air behind the radiator. Engaged (high...

Reproduction thermal fan clutch that fits 1967 - 68 289 engines, 1968 302/390/427/428CJ engines, and 1969 351W engines, all with original Ford thermal cooling fans. Slightly larger in overall diameter, (still fits fine), and retains the correct spacing from radiator. We know that these will fit Mercury Cougar and Ford Mustangs 1967-69. Closest reproduction fan clutch on the market that fits the original and reproduction C8OE-B 7 blade power fan. Hayden fan clutch with an overall height of 2.98...

Spot-On reproduction from WCCC! C8OE-B Application for 1968 includes all 390-2V, 390-4V, 427-4V, and 428 Cobra Jet engines with and without air conditioning. 1969 application is only the S code 390-4V engine, with or without air conditioning. Fan description - 7 blades and 18-1/4 inches in diameter. Fan does not include thermal fan clutch. We do sell a Hayden replacement fan clutch. Replaces Ford master part number C8OZ-8600-A. This fan will also work on many small block applications. We hope...

Used in conjunction with Ford fan part # C9ZZ-8600-C that is stamped C9ZE-E. Features a parkerized shaft with an integral mounting flange. The aluminum portions are finished with silver cadmium and are mated together with filister head, Phillips machine screws (8) and an additional crimping operation was used to assemble the front and rear housings. The radial curved spring was originally finished in gold cadmium. This assembly stands 2 5/8" tall when set on its front surface, and the distance...

Heavy Duty reproduction fan clutch that fits the original and reproduction C9ZE-E 7 blade power fan. Hayden fan clutch with an overall height of 2.707 inches. About 5/32" taller than our standard duty fan clutch. Please make sure that you have the clearance behind your radiator.  Similar design as originals, with thermal activated clutch. Overall diameter is 7.25 inches. The C9ZE-E 7 blade clutch fans were installed on 1969-70 Mercury Cougar and Ford Mustangs as well as 1969 Torino,...

C7AE-D, Fan description - 5 blades and 18 inches in diameter. Ford master part number C7AE-8600-D. These 5 blade flex fans usually came on full sized Ford and Mercury cars starting in 1967. Can be used on any engine with the proper spacer with fan shroud with adequate fan opening. Check out this interesting video where they test the efficiency of factory style and aftermarket fans. Spoiler alert: the clutch fans are the most efficient! ...

C9OE-A radiator cooling fan. Multiple applications over the years. 4 blade fan, 14 inches in diameter. Not sure when these actually started being installed on the assembly line if at all. The C6AE-E version was used well into 1972 or later. Ford part number C9OE-8600-A. *Note - Excludes integral air conditioning. **Note - 1973 there is a note in the MPC that states this fan may be marked C9OE-A. Check out this interesting video where they test the efficiency of factory style and...

Replaces Ford part # C9ZZ-8146-C. This is an excellent reproduction made from the original Ford tooling and features the original Ford logo and part number. This is for the 20" radiator. Click on images to enlarge Customer feedback found at mercurycougar.net: Boy service is just not the same as the "good old"? days. I ordered a half a trunk load of parts and pieces from West Coast Classic Cougar and about 2 hours later got a phone call informing me that the order was picked and shipped. What...

Replaces Ford part # C8ZZ-8146-A. This is a good reproduction made from the original Ford tooling but does not have the original part number or FoMoCo lettering. Has a smooth texture (unlike original) but it is made from a more durable plastic material. This is for the 24" radiator only. For some helpful tips on upgrading your Cougar (or Mustang) cooling system, check out our video: ...

Replaces Ford part # C9OZ-8146-A. This is a quality, made in America reproduction made from the original Ford tooling. This is for the 24" radiator found on Mustang, Torino and Cougar with AC or for Cougars that need extra cooling capabilities beyond what the 20" radiator / shroud can deliver. NOTE: This shroud will fit on the 67, but will only work on small block Cougars that have been retrofitted with a 1968 - 1969 24" small block radiator and mounts. For some helpful tips on upgrading your...

Fan shroud installation kit for 67 - 71 Cougars and Mustangs. Will fit 1971 Cobra Jet shrouds.

Used grade "A" under dash wiring harness with a black plug end for the standard 1969 Mercury Cougar with air condioning. Mercury used either a black or white plug end during the 1969 model year run. If you have a blue printed circuit board, this is the unit you need. All electrical harnesses are inspected, repaired, tested, and ready to install. *NOTE* Excludes Eliminator - see 1969 XR7. If you send us your old used under dash harness, you will receive an in store credit of up to $100. Also...

Used grade "A" under dash wiring harness with a white plug end for the standard Mercury Cougar. Mercury used either a black or white plug end in the 1969 model year run. If you have a red printed circuit board, this harness is the one you need. All electrical harnesses are inspected, repaired, tested, and ready to install. *NOTE* Excludes Eliminator - see 1969 XR7. If you send us your old used under dash harness, you will receive an in store credit of up to $100. Also keep in mind that we buy...

Used grade "B" under dash wiring harness with a white plug end for the standard Mercury Cougar. Mercury used either a black or white plug end for the under dash harness during the 1969 model year run. If you have a red printed circuit board, then this is the unit you need. All electrical harnesses are inspected, professionally repaired, tested, and ready to install. *NOTE* Excludes Eliminator - see 1969 XR7. If you send us your old used under dash harness, you will receive an in store...

C8OE-B Application for 1968 includes all 390-2V, 390-4V, 427-4V, and 428 Cobra Jet engines with and without air conditioning. 1969 application is only the S code 390-4V engine, with or without air conditioning. Fan description - 7 blades and 18-1/4 inches in diameter. Fan does not include thermal fan clutch. Ford master part number C8OZ-8600-A.Check out our cooling system upgrade below: ...

C8SE-A 1. 1969 application is very early production (before 11/6/1968) 351 engines with the 20 inch radiator. 2. 1970 application - 351 engines with manual transmissions and 20 inch radiator. Fan description - 4 blades and 17-9/16 inches in diameter. Fan does not include thermal fan clutch. Ford master part number C9OZ-8600-B. Check out this interesting video where they test the efficiency of factory style and aftermarket fans. Spoiler alert: the clutch fans are the most efficient! ...

C8SE-B Applications: 1. 1968 289-2V engines with air conditioning or the extra cooling package. 2. 1969 Boss 302 Eliminator - after 4/14/1969. 3. *1970 Boss 302 Eliminator. 4. *1970 351 with or without air conditioning. Fan description - 5 blades and 17-5/8 inches in diameter. Ford master part number C8SZ-8600-B. Multiple dates available. *Note - 1970 Boss2 and 1970 351 owners, some time soon after the start of the year the exact same fan, but with casting number D0ZE-B was used. Check out...

C9WE-C Application is only for 1969 H code 351-2V and M code 351-4V engines with A/C or the extra cooling option. Fan description - 7 blades and 17-1/2 inches in diameter. Fan does not include thermal fan clutch. Ford master part number C9WZ-8600-B. Original fan drive clutch cast number for this application is C9WE-A.

These concours quality Zinc caps are made in America and bear all the original markings. O.E.M. details include original letter style, "S.M.C.O." and "Autolite". Pound rating is stamped on cap. Replaces Ford Part #: C7ZZ-8100-A.

These are O.E.M. replacements and will not fit most after market radiators.

Keeps the corrosive agent in your coolant from destroying vital engine components

Replacement radiator cap for the 1967 - 1973 Mercury Cougar or 1967 - 1973 Ford Mustang. This radiator cap releases pressure when the pressure exceeds 13 pound of pressure.

New 13 Pound Generic Radiator Cap with Safety Release for the 1967 - 1973 Mercury Cougar / Ford Mustang

Usually ships in 3-5 business days. For the 1967 - 1969 Small Block Cougar and Mustang and 1970 351c & 351W with AC and or heavy duty cooling package. For optimum cooling you will want to purchase a shroud as well. Most Cougars these days have been bored .030 or more and many have had performance upgrades which all lead to increased heat. Before you buy fancy wheels, valve covers or most anything else (except brakes) this should be at the top on your list. Many applications only call for a 2...

For the 1967* - 1969 FE / Big Block Cougar and Mustang and 1970 351c & 351W with AC and or heavy duty cooling package.  For optimum cooling you will want to purchase a shroud as well. Most Cougars these days have been bored .030 or more and many have had performance upgrades which all lead to increased heat.  Before you buy fancy wheels, valve covers or most anything else (except brakes) this should be at the top on your list.  Many applications only call for a 2 core but we...

Usually ships in 3-5 business days. For the 1967 - 1969 small block Cougar and Mustang with AC and or heavy duty cooling package. If you currently have the 20" wide radiator that bolts to the core support, do know you will need to buy upper and lower cradle mounts to mount this 24" wide radiator properly. For optimum cooling you will want to purchase a shroud as well. Most Cougars these days have been bored .030 or more and many have had performance upgrades which all lead to increased heat....

All steel fitting for the lower radiator tank, found on all cars with automatic transmissions. The fine threads go to the radiator and the transmission cooling line screws onto the flared fitting after installation into the radiator. Two needed per car, sold individually. Fits all years 1967-73, and all automatic transmissions. 1/2" threads go to cooling lines. 3/8" threads go into the radiator. *Note - This is an original steel fitting, not a brass reproduction. ...

Reproduction pair of brass oil cooler fittings for the Mercury Cougar or Ford Mustang that screws into the oil cooler. 1/2" threads go to cooling lines.3/8" threads go into the radiator.

Used FoMoCo 24 inch small block radiator. This is for a 1969 Mercury Cougar or Ford Mustang with 351-2V or 351-4V and FMX (automatic code X) transmission. Used core radiator for recoring and restoration. Typical Dearborn installed assembly line radiator. Lower tank does have the connections for installing the transmission cooling lines. Various dates available, please choose one of the dates in the comments section of your order. Current dates available: 8LD (4th week Nov 1968), 9BA (1st week...

Reproduction overflow hose with smooth outer wall. Hose length 36"

Used FoMoCo radiator marked C8ZE-S1 and dated 9AA, which we believe is 1st week of January 1969. This is for an mid year built 1969 Mercury Cougar or Ford Mustang with 390-4V or 428CJ and automatic transmissions. Good used radiator for recoring and restoration. Replaces Ford part number C8ZE-8005-S1 or C8ZZ-8005-S.

Fits all* Ford V-8 engines, 1967 - 1973. *- NOTE: This will fit in the 351C, 351M or 400 but will not block off the port to recirculate the water back through the engine.  This can cause the engine to run hotter than desired.

Fits all* Ford V-8 engines, 1967 - 1973. *- NOTE: This will fit in the 351C, 351M or 400 but will not block off the port to recirculate the water back through the engine.  This can cause the engine to run hotter than desired.

Fits all* Ford V-8 engines, 1967 - 1973. *- NOTE: This will fit in the 351C, 351M or 400 but will not block off the port to recirculate the water back through the engine.  This can cause the engine to run hotter than desired.

Correct head-stamp. 

Cast construction with very good quality chrome. Looks great with chrome valve covers and air cleaner. For some helpful tips on upgrading your Cougar (or Mustang) cooling system, check out our video:

Reproduction aluminum cast A356 water neck for FE Big Block engines. Made from original factory blueprint, and includes the correct stamping. Will fit the 67 Big Block, but markings are correct for 68. Replaces Ford Part #: C8AE-8592-B.

Aluminum casting, made in the U.S.A. Exact copy of original, including part numbers. Fits any small block Ford 260/289/302/351W but would have only been correct on 1967 Mercury Cougar and 1965-67 Ford and Mustang with 289 engines. Has natural cast finish as original. Does not have the provision for the thermal vacuum switch starting in 1968 and newer small block Ford V-8 engines. Replaces Ford Part #: C5OE-8592-A For some helpful tips on upgrading your Cougar (or Mustang) cooling system, check...

These bright beautiful reproductions replace those corroded and rusty originals that just look nasty. Replaces Ford Part #: C8AZ-18599-C

Thermostat Housing Gasket By FEL-PRO® for the Big Block. REplaces Ford Part #: C7ZZ-8255-D.

Thermostat Housing Gasket BY FEL-PRO® Replaces Ford Part #: C5AZ-8255-A.

This elbow is zinc plated for years of reliable service and is for 351, 390, and 428 engines. Replaces Ford Part #: D0AZ-18599-A.

Elbow with water restrictor.

This fail safe thermostat can save you from costly engine damage during an overheat. They feature an exclusive technology that locks the valve open position if overheating occurs. This allows for maximum coolant flow when you need it most.

Used aluminum water neck of thermostat housing for most 1967-70 Mercury Cougar or most other Fords with 390/427/428CJ engines. Cast aluminum finish. Comes with threaded hole for either a screw-in cap, or thermal switch. For use with common 2-1/8 inch thermostats. Correct for 1968-70 FE engines. Not going to lie, these will show some signs of electrolysis on the inside and where the hose slips on. Additionally, we notice that the threads get a bit rotted out where the thermal switch...