All Available Parts - 1969 Mercury Cougar

Original style fuel tank installation screw. 3/8 inch hex head. Black phosphate finish on this reproduction, originals were plated. Fits all 1967-70 Mustang and Cougar fuel tanks. See item 11942 for the kit of 12 screws, better value.

Original style fuel tank installation screw kit. 3/8 inch hex head. This is a set of 12 new screws. Black phosphate finish on this reproduction, originals were plated. Fits all 1967-70 Mustang and Cougar fuel tanks.

Used factory installed vented fuel, or gas cap as installed on 1967-69 Mercury Cougar 1970 cars without California emissions. Also fits 1969-70 Shelby Mustang. In 1970 California required a non-vented fuel cap.We stock these in limited quantities, and will have an intact paper gasket. Correct "VENTED" embossed and has the "S" stamped onto the center rivet. Price is established by demand, and these normally are only needed for very high level restorations or strict concours judging...

Reproduction anti rattler board - 1/8" panel board that prevents rattling noise. Installs on top of fuel tank on the side where the jack and spare tire mount.Measures 12" X 6"

Used original wire clamps for retaining the filler hose to the tank standpipe and filler neck. These are sold as a pair. Ford Part #: C5ZZ-8287-A.

New manufactured stainless steel fuel / gas tank for 1969 Mercury Cougar and 1969 Ford Mustang, 20 gallon capacity, has drain plug. Replaces Ford part #C9ZZ-9002. *NOTE* Tank will fit into all 1967-68 cars, fuel filler necks must be adjusted to fit with this taller tank. Sending units ideally should be changed to the 1969 sending units. 1970 cars with California emissions will have to change filler necks entirely.

You will have to look closely to find the differences between this economy and our premium version. If you look closely you will see this one is a shade darker than OEM.  Replaces Ford part number C9WB-13A568-B ...

Reproduction fuel filler neck for the 69 Mercury Cougar, to be used with factory or reproduction 20 gallon fuel tank.

Very good used door glass with no deep scratches (multiple faint scratches and water spots often will be present). Not perfect but the best you could expect to find from a 50 year old plus parts car and will of course be a better fit than repro. Look for the SUN-X logo to determine if your glass is tinted or not. For those wanting Grade "A" glass, we recommend calling us so we can discuss with you the glass that we have available.Need a little help identifying some of the markings on your...

Used grade "B" tinted rear window glass for the Mercury Cougar coupe that features the "Sun-X" green tint. This unit has multiple fine scratches and water spots and is good for driver or something to "just plug the hole." It is almost impossible to remove even fine scratches from tempered glass. All air conditioning cars were supposed to always come with tinted glass, but we have documented cases of them coming with clear glass. Tinted glass was also available as an option in cars not...

Quality reproduction GREEN TINTED rear window glass that unfortunately does not have original "Carlite", "SUN-X" markings or date code. This glass does not have the faint Car-Lite markings in the corner but rather very bold, large SAFETY GLASS in raised letters that cannot be removed without special equipment. Many feel a few minor scratches on an original look better than the raised white lettering found on repros. Keep in mind the fit is slightly better on the used original. Keep in mind...

Quality CLEAR Rear Window Glass for the 1969 or 1970 Mercury Cougar. Will not come the the "Carlite" logo or a date stamp. This glass does not have the faint Car-Lite markings in the corner but rather very bold, large SAFETY GLASS in raised letters that cannot be removed without special equipment. Many feel a few minor scratches on an original look better than the raised white lettering found on repros. Keep in mind the fit is slightly better on the used original. Keep in mind that the...

Used grade "B" clear rear window glass for the Mercury Cougar coupe. This unit has multiple fine scratches and water spots and is good for driver or something to "just plug the hole." It is almost impossible to remove even fine scratches from tempered glass. 

These are hand picked grade A condition original arms with no defects. Right is the same as left. Sold individually, two per car.The reproductions of the 67-70 are identical, but the originals are not the same between years. The 67-68 and the 69-70 were bent at different angles and carry different Trico patent numbers.In our experience in owning and parting 100's of early Cougars, 1967 and 1968 use the early style, and 1969 and 70 use the later style.Click here to see pics of the...

Satin Finish Wiper Arm

Replaces Ford Part # : C9ZZ-6503406Sold Individually.

This excellent reproduction windshield washer bottle includes the Ford logo on the lid ( C9ZZ-17632-A ) and part number C9ZF-17B613 stamped on the top of the bottle exactly like the originals. The tooling was made using the original Ford blueprints and nice original patterns. Blow Molded Plastic. There are two available reproductions

Windshield washer hose clip that holds the hose up under the cowl. Concours quality

Injection molded high strength plastic connector for hoses leading to nozzles. Factory fit.Replaces Ford Part #: C7SZ-17A601-A or C0AB-17A601-A.Will not fit 69-70 with factory hoses as they used Ford part # C8OZ-17A601-A

This is a reproduction of a later service replacement version of the windshield washer pump for the 1969 - 1973 Cougar and Mustang (and other Ford / Mercury models).The original Ford part was part number C9AZ-17664-C

These zinc-plated Washer Nozzles are good copies of the originals. 1969 and 1970 Mercury Cougar and Ford Mustangs only. Sold in pairs.Replaces Ford Part C9ZZ-17603-A and D0ZZ-17603.

Repro New Clear Windshield for Cougar. Replace that scratched and pitted old glass with the milky top, Our new glass is clear as rain, and works great too! BECAUSE OF THE HIGH COST OF SHIPPING, ALL WINDSHIELDS ARE AVAILABLE FOR DROP SHIP OR LOCAL PICK-UP ONLY. Our website is currently unable to accurately calculate truck freight costs, so don't be deceived by the shipping rate displayed. Keep in mind this is a common windshield that can be picked up locally from most any automotive glass shop....

Reproduction  Lower Windshield Moulding Retainer for the 1969 1970 Mercury Cougar or Ford Mustang  

Reproduction  Lower Windshield Moulding Center Spacer for the 1969 1970 Mercury Cougar or Ford Mustang  

Used spacer for the lower windshield moulding

Reproduction  Lower Windshield Moulding Fender Spacer for the 1969 1970 Mercury Cougar or Ford Mustang  

Original FoMoCo used two speed windshield wiper motor for your 1969-70 Mercury Cougar or Ford Mustang. This used motor comes with wiring harness with unique grommet for the firewall specific to 1969-70 Cougar and Mustangs. Motors are tested and guaranteed to work, 90 day warranty. Linkage arm for the 1969-70 installation, must be marked 9Z. Linkage arms sold separately. Ford part # C9ZF-17504-C.

Linkage arm that attaches to the windshield wiper motor that is unique to the 1969-70 Mercury Cougar and Ford Mustang. These are marked 9Z, among other things the slot is specifically indexed for the 69-70 Cougar and Mustang application. This is basically an installation kit that includes: linkage arm, flat bushing, wave washer, and nut. The order of installation is flat bushing, wave washer, linkage arm, and lastly the nut.

Pair on reproduction lower windshield stops for all 1969-70 Mercury Cougar and Ford Mustangs

The hinges on these original arms tend to get worn out which will cause irregular movement and can eventually burn up your wiper motor or bind up the linkage. If your wipers do not move in tandem

This is the set of six bolts needed to attach the pivot section of the wiper arms to the cowl on 1969-1970 Cougars and Mustangs. Three bolts needed per side

Used windshield wiper motor cover or shield as Ford called it. Very prone to cracking and 'chalky' from age or UV light. We are not going to lie, most of these will have paint over spray or a slight amount of chalkiness. We haven't found a Ford part number other than the basic number of 17C441 which is labeled as "Shield - (Windshield Wiper Motor - Water)" as found in the Mercury MPC.

Original Trico stainless wiper holder assembly, removed from a 1970 Mercury Cougar. Fits any 1969-70 Mercury Cougar and Ford Mustang. Has the original metal fastener to connect to your wiper arm, rather than the plastic piece used in the reproductions. Sold individually, two per car, 16" rubber wiper blade not included.*Note - This is NOT, repeat NOT the ultra rare 1969 production wiper blade holder assembly. This is a Trico 16 inch blade holder as found on most 1970 cars.

New lower windshield moulding retainer screw. The retainers slide into the lower stainless steel windshield moulding and attach with these screws into the cowl top. #8 x 1/2 inch hex washer head screw with 1/4 inch drive. Several suppliers or styles of screws were used

Original FoMoCo used windshield wiper motor mounting bracket for your 1969-70 Mercury Cougar or Ford Mustang. This used bracket comes with grommets, for all 1969-70 Cougar and Mustangs. Mounts under the cowl cover at the windshield. Ford part # C9ZZ-17496-A.

This check valve is located in-line just behind your carburetor. To test it simply place it in your lips and try blowing through the side with the single port. You should be able to breath in and not breath out. If this valve is bad you will find the headlights opening up after the engine has been shut off on your 1969 - 1970 Cougars and your tilt away function not working correctly on your 1967 - 1970 Cougars equipped with a tilt column. A good working vacuum system should be able to...

Used passenger side (right hand) outer semi gloss black headlight adjusting ring that holds the headlight bulb in place of the Mercury Cougar. Marked C8AB-37-A and "RL", There are four different versions used, but they are the same for the 1967-68 Cougars. They are secured by two adjusting screws and the stainless steel headlamp retaining ring that fits over it. These are rust free, taken from a Western parts car and are sold individually. This exact same ring was also used 1969-70, but was...

*NOTE* If you're going to make your car concours correct, you need to specify which year you have (bulbs are date marked), otherwise we'll just send you any random FoMoCo bulb.Please note that we are out of date coded bulbs for 1969 and up.  If ordering online, leave the info in the comments section of your order. If your order is being done over the phone, be sure our rep knows which year you have. This is the much harder to find outer, low beam lamp distinguished by the number 2 at 12...

This is the correct ring for all years 1967 - 1973 high beam or low beam. No dings, gouges or broken spot welds. It is held in place by a spring and two screws. Four rings required per car, sold individually. Made from stainless steel, these clean up nicely with fine steel wool. Ford part number C7AZ-13015-B. Below is a comparison of the Repro and Used/NOS Headlight rings: Click on images to enlarge. The above picture shows the Used (top left), NOS (center), and Repro (bottom right) Headlight...

C7SZ-13A165-A Bolt like pin that one or both sides of the hidden headlight hinge rides on. 1967-68 Mercury Cougar uses 4, 1969-70 Mercury Cougar uses 2 on the outsides. Also used on many other 1967-71 Ford, Mercury, and Lincoln cars with the vacuum operated hidden headlights. 1967 - 1970 Mercury Cougar and XR7 1967 - 1969 Ford Thunderbird or T-Bird 1968 - 1969 Ford and Mercury full sized cars 1971 Ford and Mercury full sized cars 1970 and newer Lincoln Continental 1969 - 1971 Lincoln...

This fine threaded Phillips screw assembly is the mechanism in which to adjust your headlights up or down, left or right. There are two units per bulb for a total of eight per car. The two new screws that mount them to the grille are included at no extra cost. They will be in perfect working order and not rusty as we only keep the best examples. Two versions for 1967-68, the most common has the square corners and is rectangular, the other supplier had clipped corners as shown in the comparison...

Reproduction headlamp adjusting nut and screw. Slightly longer screw than stock, small amount of added length does not interfere with anything in or behind the grille. The nut is an exact copy of what is found on the 1969-70 adjustment. Almost the same as the nut found on the 1967-68 Cougar, this isn't even shown on those grilles. 1967-68 mounts on the backside of the headlight bucket. Total of 8 adjustment screws used on each 1967-70 Cougar, item sold individually.Note: When installing...

This clip mounts the actuator shaft to the eyelids. Two required for 1967 - 1968, one required for 1969 - 1970. Same clip holds the windshield wiper motor to the wiper transmission. Replaces Ford part number C4ZB-17450-C.

Reproduction Headlight / Tilt Column Vacuum Check Valve for the 1967 to 1973 Mercury Cougar, Cyclone, Marquis, Ford Torino, Ranchero, Galaxie, LTD, Thunderbird, Lincoln Continental and Mark III. NOTE: The direction of flow is up through the dual ports and out through the single port.  For more in depth detail on this reproduction, see pictures below. *NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've...

These are the correct ring for all years 1967 - 1973 high beam or low beam. No dings, gouges or broken spot welds. They are held in place by a spring and two screws. Made from stainless steel, these clean up nicely with fine steel wool. Ford part number C7AZ-13015-B. Below is a comparison of the Repro and Used/NOS Headlight rings: Click on images to enlarge. The above picture shows the Used (top left), NOS (center), and Repro (bottom right) Headlight rings side by side. If you look close at...

Used passenger side (right hand) inner semi gloss black headlight adjusting ring that holds the headlight bulb in place of the Mercury Cougar. Marked C8AB-16-A and "RH", There are four different versions used, but they are the same for the 1967-68 Cougars. They are secured by two adjusting screws and the stainless steel headlamp retaining ring that fits over it. These are rust free, taken from a Western parts car and are sold individually. This exact same ring was also used 1969-70, but was...

Used driver side (left hand) outer semi gloss black headlight adjusting ring that holds the headlight bulb in place of the Mercury Cougar. Marked C8AB-47-A and "LL", There are four different versions used, but they are the same for the 1967-68 Cougars. They are secured by two adjusting screws and the stainless steel headlamp retaining ring that fits over it. These are rust free, taken from a Western parts car and are sold individually. This exact same ring was also used 1969-70, but was moved...

Used driver side (left hand) inner semi gloss black headlight adjusting ring that holds the headlight bulb in place of the Mercury Cougar. Marked C8AB-17-A and "LH", There are four different versions used, but they are the same for the 1967-68 Cougars. They are secured by two adjusting screws and the stainless steel headlamp retaining ring that fits over it. These are rust free, taken from a Western parts car and are sold individually. This exact same ring was also used 1969-70, but was moved...

Set of 8 fine threaded Phillips screw assemblies. This the mechanism in which to adjust your headlights up or down, left or right. There are two units per bulb for a total of eight per car. The new screws that mount them to the grille are included at no extra cost. They will be in perfect working order and not rusty as we only keep the best examples. Two versions for 1967-68, the most common has the square corners and is rectangular, the other supplier had clipped corners as shown in the...

Quality "STANDARD" brand reproduction switch for your vacuum actuated hideaway headlights. This switch fits multiple years and makes which means multiple dash configurations. You will need to "break off" your unique extension and attach it to this unit. The extension (spacer) can be removed easily by placing your old switch in a vise and using a wedge shaped chisel to break the tiny spot welds. When reattaching, most any glue such as Gorilla glue, JB weld or even silicone will work as you are...

Hardware for mounting the hood bumpers on the radiator core support. Clip mounts with threads down, nut on top. Sold as a Kit as Pictured.

These simple little grille repair clips have been needed since these cars were new! Over the years I have seen many home remedies to fix this common problem but none were this clean looking, easy to install and failure proof. Soon we will list the all the different FoMoCo applications from the era that these clips apply to. These clips are sold as a set of four. Click on images to enlarge. ...

Grade A original center with no obvious pitting or cracks. Keep in mind we will give up to $200 trade in for your cracked, broken or moderately pitted grille center in trade. Send us a few good pictures and we can quote what trade in value you would receive. Casting number: C9WB-8A133 This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit of 50% of our web price for parts delivered in hand...

Used to mount the vacuum storage tank inside the driver fender, two required per car, sold individually. Exact same part as what is found on the 1968 Cougar just a slightly different clips is used for 1969. Cougar part number C8WY-13B008-A.

Complete mounting kit for the vacuum storage tank located inside the front portion of your driver side fender.

Good rust free tank taken from a Western parts car. Differs from other years in that the vacuum port is located in a different position. Located under the driver fender. Keep in mind we have units that are not as clean but still hold vacuum for about half the price. Cougar part number C9WY-13A185-A.

Used headlight switch for the Mercury Cougar. This original FoMoCo unit was tested and will hold 13 pounds of vacuum. The spacer (which is specific to 1969) is not included with this unit, but you can get it right here. Ford part # C9WB-11652-B.

This used original, color coded set of vacuum hoses is 100% complete and relatively pliable. It comes complete with decades of dirt and grime (patina) for no extra charge. If you want to remove the grime it will take some serious elbow grease but it can be done. The color coded stripes are quite resilient to cleaning as the ink used actually embedded itself into the rubber. If you have a tried and true method of cleaning these hoses let us know and if it sounds good we will post it here! Does...

This is a complete 1969 (one year only) grade "A" grille bright work set taken from a Western parts car(s) with no obviously visible cracks, pits on the face of the chrome or bends. Not perfect, but the best we can obtain, usually taken from three or more cars to make one set. This set includes two halves, two eye lids and one center section (which often we will include a reproduction in lieu of used). Brackets, hardware and actuator are sold separate but often we will throw in several pieces...

Powder Coated. Replaces Ford Part Number: C9ZZ-17385, correct for a 1969 Mustang or Cougar but works fine on a 1970 Cougar.

Our grade B, driver quality grille halves are nothing to brag about... We will assure you they will have no more than one break in the area shown. If they have two breaks then there is nothing to support the horizontal bars. We will often ship these parts with a zip tie to hold the grille together and to avoid further damage in shipping. Once bolted in place you will not easily be able to tell there is a break as the upper and lower mounting tabs will keep the grille bars rigid and together....

Our grade B, driver quality grille halves are nothing to brag about... We will assure you they will have no more than one break. If they have two breaks then there is nothing to support the horizontal bars. We will often ship these parts with a zip tie to hold the grille together and to avoid further damage in shipping. Once bolted in place you will not easily be able to tell there is a break as the upper and lower mounting tabs will keep the grille bars rigid and together. When ordering less...

Used grade "A" passenger side (right hand) headlight eyelid door for the Mercury Cougar as taken from a Western parts car. This unit will not have any bends, cracks, or pits on the face of the chrome. Not perfect, but the best original unit we can obtain. Casting number: C9WB-13A38 NOTE: Item does not include corral or emblem assembly

Used grade "A" driver side (left hand) headlight eyelid door for the Mercury Cougar as taken from a Western parts car. This unit will not have any bends, cracks, or pits on the face of the chrome. Not perfect, but the best original unit we can obtain.Casing number: C9WB-13A139

This grade "B" support will be rust free but will need minor straightening on the lower mounting tab. Once worked on the damage should not be noticeable. Customer feedback; Hey Don, I've been ordering parts for my '67 over the last few months from your company. I just want to let you know I would recommend your company to anyone. You have been extremely helpful in every aspect. I think your site is great and easy to use. I especially liked how you call me with questions and answers...

Used Driver Side Grade B Center Grille Support for the 1969 Mercury Cougar

Used Passenger Side Grade A Center Grille Support for the 1969 Mercury Cougar

Used  Grade A driver side support / grille center for the 1969 Mercury Cougar

C9WY-13A154-A Hinge that the hideaway headlamp covers attach to on the grille. This is the passenger side only. See C9WY-13A155-A for the driver side hinge.

Reproduction nuts for mounting the 1969 Mercury Cougar headlight door or eyelid cover to the hideaway headlamp hinge.

C9WY-13A155-A Hinge that the hideaway headlamp covers attach to on the grille. This is the driver side only. See C9WY-13A154-A for the passenger side hinge.

C9AZ-13B013-A Center section that connects to the vacuum motor on many 1969 Ford and Mercury cars with vacuum covered headlights. 1969 Mercury Cougar including XR7 and Eliminator. The center piece is offset to the left of center and the hook part that goes to the vacuum motor points down. 1969 and 1970 center shafts are not interchangeable. 1969 Ford LTD 1969 Galaxie and Galaxie XL 1969 Country Squire Wagons 1969 Mercury Marquis 1969 Mercury Brougham 1969 Marauder and X-100 1969 Colony Park...

Used outer bushing for the hinge pivots for the hide-away headlights on the Mercury Cougar. Hole size is 5/8", shaft size is 3/8". Fits many of the Ford, Lincoln, Mercury cars with vacuum headlight covers. List includes 1969-71 Full size Ford Galaxie, LTD, XL, Country Squire, and Mercury Marquis, Brougham, and Monterey. Lincoln Continental starting in 1970 until? 1972-? Lincoln Mk IV. Also select Cylcone / Fairlane / Torino 1970-71 any with hide away headlights. Ford part # C9AZ-13A164-A. ...

C9AZ-13A164-B Inner grille bushing, where the hidden headlight hinge pivots. Hole size is 3/4", shaft size is 1/2". Fits many of the Ford, Lincoln, Mercury cars with vacuum headlight covers. List includes 1969-71 Full size Ford Galaxie, LTD, XL, Country Squire, and Mercury Marquis, Brougham, and Monterey. Lincoln Continental starting in 1970 until? 1972-? Lincoln Mk IV. Also select Cylcone / Fairlane / Torino 1970-71 any with hide away headlights.

C9AZ-13A163-C Coil spring for the hidden headlamp hinges on all 1969-70 Mercury Cougars and 1969 full sized Ford cars with hideaway headlights. Sold individually, one per side. 1969 Mercury Cougar including XR7 and Eliminator. 1969 Ford LTD 1969 Galaxie and Galaxie XL 1969 Country Squire Wagons

Used headlight wiring harness for either side of the Mercury Cougar. This harness is the sub-harness that connects your headlights to the under hood harness. The Cougar uses one per side and they are identical. Sold individually.Ford part # C9ZZ-13076-A, tagged C9ZB-13076-B.*NOTE* A pair of these units were also used on the 1969 Mustang and Mach 1. However, they were not used on the quad headlight 1970 Mustangs.

C9WY-13B014-A Shaft assembly for passenger side hideaway headlamps for any 1969 Mercury Cougar. Complete with rag joint and nut. Sold individually, one per side. These have become side specific due to time, and stress on those rag joints.

Shaft assembly for driver side hideaway headlamps for any 1969 Mercury Cougar. Complete with rag joint and nut. Sold individually, one per side. These have become side specific due to time, and stress on those rag joints.

Reproduction Grille Bolts & U Nuts for the 1969 Mercury Cougar / Ford Mustang.If you're working on both sides of your grille, you will need two kits, one kit will do one half of the grille.

Reproduction Headlamp Housing Grille Bolts & U Nuts for the 1969 Mercury Cougar / Ford Mustang

1969-1970 Headlamp adjusting screw. Two per bulb, eight in all per car, comes with two new mounting screws. This part is identified by the clipped corners. Also used during 1967 and 1968 on a limited basis. Will be in good rust free condition as we only keep the best examples.Also sold in a set of 8. ...

1969 Hidden Headlight Cover Stop Bracket with nut, for all 1969 Mercury Cougar and 1969 full sized Ford and 1969-70 full sized Mercury. Mercury part number D0MY-13A096-A.

Captured washer, or spinning washer nut for attaching the headlamp motors or vacuum actuators on the 1969-70 Mercury Cougar. All models, Standard Hard Top, XR7, and Eliminator. Two needed per car, sold individually.

Spring that holds the headlight trim ring on each headlamp to the grille. 4 springs per car, sold individually.Ford number C6AZ-13031-C.

Requires you to PRE-PAY a core charge of $30. Used grade "B" headlight door actuator for your Mercury Cougar. This grade B actuator has been reconditioned with new seals but will still slowly leak down after time as not all of them will function as new after being reconditioned. These actuators are sold individually on an exchange basis or outright (for an additional core charge). One actuator actuates both headlight doors on the 69-70. This unit also comes with a 30 day warranty. Ford part #...

Reproduction green tinted windshield that features a blue tinted band a crossed the top of the windshield. Not only will this unit look great, it will fit perfectly as well. Planning on installing the glass yourself? We also sell the glass to window channel weld. BECAUSE OF THE HIGH COST OF SHIPPING, ALL WINDSHIELDS ARE AVAILABLE FOR DROP SHIP OR LOCAL PICK-UP ONLY. Our website is currently unable to accurately calculate truck freight costs, so don't be deceived by the shipping rate displayed....

Best replacement for the original wiper blade assembly. Replaces Ford part #: D4AZ-17528 and C9AZ-17528-A. Sold individually

This conversion will replace the old, tired, vacuum system that likes to leak and wear out. There are few differences between the 1969 and 1970 conversion kit. This kit consists of an electric actuator assembly (new Mazda Miata motor) with a plug and play wiring loom for easy installation. Simply remove all existing vacuum components and replace with this kit to have headlight covers that work under any conditions with the car running or not. These new motors are smoother and more reliable...

Attaching screws for the headlamp adjusting screws for the 1967-70 Mercury Cougar and most other Ford and Mercury cars and trucks. Each of the headlamp adjusting screws uses 2 of these screws. A Cougar with 4 headlights would need a total of 16 of these screws.

Used hood latch for a 1970 Mercury Cougar, it will fit the 1969 too. Starting in 1969 until 1970, Mercury had three different hood latches. This 1970 version has the longest handle, and is the easiest to operate. Those early 1969 latches are a two finger operation for those of us with large hands. The part shipped will likely not be as clean as the one in the picture.Replaces Ford part number D0WY-16700-B.

Used upper support bracket for the hood latch on any 1970 Mercury Cougar. This 1970 part will work on a 1969. The only difference is the top corner is clipped at an angle on the 1970.Ford part number D0WY-16707-A.

Set of 16 attaching screws for the headlamp adjusting screws for the 1967-70 Mercury Cougar and most other Ford and Mercury cars and trucks. Each of the headlamp adjusting screws uses 2 of these screws. A Cougar with 4 headlights would need a total of 16 of these screws.

Sold individually, black only. We have an array of colors in good used condition used. We also have the hard plastic bracket that this slips over. Four are required per car. Replaces Ford Part #: C8AZ-6229024-A.

These are the plastic brackets that screw to you roof and then slide the vinyl colored piece over. Sold individually, four are required per car. Replaces Ford part # C8AZ-6229232.

Reproduction roof / headliner insulation kit for your Mercury Cougar or Ford Mustang. An effective item that will increase the efficiency of your heater or A/C. This will also insulate your interior from outside sounds.

Two piece kit, one piece for the headliner, and a second piece for covering the sunroof panel.On early production cars Ford pulled the cars off the assembly line to sent them to ASC Golde for install. Golde used 3 bows for installing the headliner, whereas in later production Ford used 2 bows when installing them on the assembly line. These headliners are for 2 bows installations. If you have 3 bows, you will need to order a standard headliner, then cut it to fit. Check out our video below...

Reproduction interior windshield / A pillar post mouldings / trim that features a vinyl overlay and 2 inch gauge pods on the driver side (left hand) so you can add any gauges of your choice to your Mercury Cougar or Ford Mustang. These units are sold in pairs.

Interior windshield / A pillar post mouldings / trim for 69 - 70 Cougars and Mustangs that feature two 2" gauge pods on the driver side. Sold as a pair.  These are not the best fit but will work, notice it requires exterior screws to mount them. No returns.

This is the 1968 coupe version of the 2 hole front mounting sun visor center bracket and is a close match for the 1968 / 1969 / 1970 convertible sun visor bracket.  This bracket is not, however, an exact match for 1971 /1972 / 1973 convertible as some sites suggest, but it will work. On the 71 - 73, the hole spacing and distance from the windshield are identical to this bracket, but the bracket is not the same size. This bracket is 1/8" longer on the...

Reproduction Sun Visor Bracket & Rod for the 1967, 1968, 1969 and 1970 Mercury Cougar or Ford Mustang. Great quality and fit, left and right use same part, sold separately. Replaces Ford part # C7AZ-6204144-A.