All Available Parts - 1969 Mercury Cougar

Grade "B" used backup light lens for passenger side 1969 - 70 Cougars. This lens will show some wear, and will also have a few minor cracks and scratches. Cracks inside the plastic from stress, not contact. Ford part number: C9WY-15514-B

Reproduction pair of parking light bezels. Applications include 69 - 70 Mercury Cougar, 1969 Ford Mustang Shelby GT-350 and GT500, 1970 Mustang Sport Lamp Bezels, 71 - 72 Maverick Grabber, 1973 - 1974 Maverick (until 8/12/74) and 1971 - 1974 Comet. Replaces Ford part # C9WY-13210-A for the passenger side, C9WY-13212-A for the driver side. *NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned...

Grade "A" passenger side (left hand) bezel with no pitting, ready to install and use as-is. *NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's and is the designer of all of our solid state sequential systems. There is no question he cannot answer! Here is a link to a great source of information on the subject. Check out this video ...

Reproduction turn signal / parking light housing for the 1969 Mercury Cougar or 1969 - 1970 Shelby.  2 required per car, left is same as right. Includes mounting studs, socket, bulb and wiring.

NOTE: WILL NOT FIT 69-73 COUGAR WITHOUT MODIFICATION TO THE CORE SUPPORT OR SPACING THE HEADLIGHT FORWARD APROXIMATELY 1/4" Reproduction complete set of halogen projection headlight bulbs for your 67 - 73 Cougar or 69 Mustang. Integrating the newest modern projection headlight technology into a slim compact bulb, these headlights will fit right into your existing headlight bucket. Each kit comes with the proper wiring adapters so all you need to do is plug one end into the bulb and...

Complete set of halogen projection headlight bulbs for your 67 - 73 Cougar or 1969 Mustang. Integrating the newest modern projection headlight technology into a slim compact bulb, these headlights will fit right into your existing headlight bucket. Each kit comes with the proper wiring adapters so all you need to do is plug one end into the bulb and the other end into your headlight harness.NOTE: From the factory, Ford made the alignment tabs different passenger vs driver side...

Will also fit late model Thunderbirds built after 10/15/68 This kit is what we recommend to fully convert your 1969 Cougar over to LED Plasma exterior lights. Our WCCC brand LED lights are amongst the brightest on the market and have been specifically engineered with the nuances of the Mercury Cougar sequential system in mind. Keep in mind that over the years folks have become accustomed to very BRIGHT tail lights in traffic and the old incandescent bulbs are not only dim, but they take time...

NOS bezel for the side marker lights on the Mercury Cougar or Ford Mustang. This is an original Ford replacement part. Used with front and rear 1969 marker lenses and fits almost all 1969 Ford and Mercury cars. Ford part # C9AZ-15A440-A, casting # C9AB-15A466-A.

Used bezel for the side marker lights on the Mercury Cougar or Ford Mustang. Used with front and rear 1969 marker lenses and fits almost all 1969 Ford and Mercury cars.  Ford part # C9AZ-15A440-A, casting # C9AB-15A466-A.

Reproduction replacement halogen bulb for your headlights. This is a clear bulb, "natural white" alternative to the "cool white" bulbs included in our halogen headlight conversion kit. 55 Watt Xenon Halogen H4/9003 bulb. Sold Individually.

Reproduction pair of halogen headlights for any 67 - 73 Cougar or Mustang. These bulbs work for both high and low beam, you simply need to bend one of the tabs back for high beam (see photo above). Keep in mind that you will need a headlight relay kit when installing halogen headlights on your car.  Benefits of switching to halogen bulbs: Brighter lightDramatically improves driver visionOptical lens for a powerful beamLong range high powered lightsCrystal clear glass face with H4 halogen...

We are excited to bring these new reproduction chrome backup light bezels for the 1969 and 1970 Mercury Cougar to the market. The sockets, pigtails and lenses are not included so you will need to gently remove your originals and install them in these bezels. You can find the lenses here.

Reproduction 22" pigtail for the 67-69 front turn signal wiring harness. Please Note: The Cougars are wired differently than some Mustangs. On some Mustangs the brown wire goes to a male plug.   This plug is a reproduction of the Cougar plug. Here is an example from the reproduction tail light we sell showing the difference: For installation on a Cougar, match up: Black Wire Black Wire Light Blue Wire Light Blue / Off White Wire Brown Wire Brown Wire ...

Sold as a pair, we suggest you send your cores in advance or at least email us several good quality images if your cores are questionable. If your cores are heavily pitted, cracked or the studs have been over tightened (causes part to dimple / warp) then your cores are not acceptable for restoration. The casting number as seen from the back reads C9WB-15A509-B and C9WB-15515-B. Ford Part # is C9WY-15500-B and C9WY-15500-A

Used side marker / rear reflector for the 1969 Mercury Cougar or Ford Mustang Part of Ford part #C9AZ-15A201-C My first deal with Don was clear back in the 1980s and I have sent a few people his way and all came away happy. While at his shop on Monday I watched Lin crawl under a convertable, phone in one hand and a tape measure in the other and measure a cross member, or drive shaft or? All in the spirit of customer service. In my opinion you couldn't deal with two better examples of what our...

This is a replacement relay for the discontinued original FoMoCo relays.  It does not appear in the same form factor, but will work just fine. The original is a metal cased unit, the replacement is plastic.  Original relays are marked either C7ZA-3E553-A (1967) or  C8ZA-3E553-A (1968 & 1969) on the mounting tab. Click Here to Download Instructions (340Kb pdf). Replaces Ford Part # C7ZZ-10B926-A or C8ZZ-10B926-A *NOTE* For tilt column service, you can contact Tony Augustine at...

Made by the original supplier! Replaces Ford part # C9AZ-11582-A Here is a helpful "How To" youtube video on how to replace your ignition switch.

Here is a helpful "How To" youtube video on how to replace your ignition switch.

Reproduction 2 speed windshield wiper switch for the Mercury Cougar or Ford Mustang. These "off shore" units are spotty at best. We recommend our good used units which you can get right here.

Oil pressure switch with press on wiring connector. 1967-73 Mercury Cougar and Ford Mustang. This is the warning light style of sending unit. Cougar body code 65A and 65C, excludes Eliminator. Additionally this sending unit also fits 1970 and newer Ford Maverick and Mercury Comet, 1968-69 Lincoln with 460 engines, and 1967-71 mid sized Ford and Mercury cars such as Cyclone, Fairlane, and Torino.Check out the video below on our new gauge tester: ...

This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit of 50% of our web price for parts delivered in hand or by carrier to our Brooks, Oregon location. If you're not interested in store credit, just shoot us an email and we will let you know if it's is something we can pay cash for. We do not send cash for parts in advance but we often can compensate you within hours of receiving the...

Good used windshield wiper switch for any 1969 Cougar or Mustang. Marked C9ZB-17A553-A on the back. This is the two speed variety, the 1970 switch has a longer shaft than this 1969 version.

1969-70 Mercury Cougar XR7 dash 3 pin on / off rocker switch. Suitable for any position, MAP COURTESY PANEL or ACCY. Switches sold pit free on the chrome. Switches guaranteed to work, but are likely stiff. Electro solvent usually helps with that sticking condition, see product label for directions prior to use. These are sold individually and in most applications four are used except in 1970 xr7 convertibles or or 1970 xr7 coupes with rear defog. In these cases a different design of switch was...

Angled cup or retainer, used with the wiper switch, it locates and maintains the angle to the dash from behind. 1969 and 1970 are different, obvious when you realize that the flat spot is indexed differently between the two years. 1969 has the flat spot oriented at the bottom. Ford part numbers: C9ZZ-17C491-A, C9ZB-17C491-A.

Reproduction ignition switch repair pigtail for your 68-69 Cougar and Mustang. This pigtail is not going to be a good fit, but if you choose this as your replacement, keep in mind that although this pigtail has an extra long resistor wire, do not splice into it or cut it down. Its resistance is dependent on its full length. This is a  cheap, inexpensive replacement, but we don't recommend it and would highly suggest going with one of our used pigtails instead.  NOTE - We've...

Used roof mounted switch that is rather delicate. As you can see from the pictures, the chrome coating has started to peel slightly. 

Used ignition switch for the 68 - 69 Cougar or Mustang. Does not include cylinder or keys.Here is a helpful "How To" youtube video on how to replace your ignition switch.

New Old Stock 1969-70 Mercury Cougar XR7 dash 3 pin on / off rocker switch. Suitable for any position, MAP COURTESY PANEL or ACCY. These are sold individually and in most applications four are used except in 1970 xr7 convertibles or or 1970 xr7 coupes with rear defog. In these cases a different design of switch was used and the surrounding bezel would be labeled "Top" or "Defog" in the farthest position to the right. The fourth switch is never used on the 1969 xr7, it is just there to...

Reproduction concours correct firewall ground wire for the Mercury Cougar. For use on 390 and 428 Cobra Jet Cougars. You can find the small block version here. This strap features the correct part number and markings. It is little details like this that will often separate 1st and 2nd place at the show.Ford part # C8WB-14303-A. ...

Reproduction concours correct firewall ground wire for the Mercury Cougar. For use on 289 / 302 / 351 engines. Will not work on 390 / 428 engines. You can find the big block version here. This strap features the correct part number and markings. It is little details like this that will often separate 1st and 2nd place at the show.Ford part # C8WB-14303-A. ...

For AM radio optional rear speaker. Ford part number C9ZB-18A900-BOverall length: 11' 7"

This harness connects the rear speaker harness to the fader switch. Ford part number C8GA-18A900-BOverall length: 44"

Grade "A" harness that runs from the passenger side door jamb to the courtesy / C-Pillar light. This harness is only needed if you have a Standard model car. NOTE: All XR7's would have already come equipped with his harness.

Used wire harness for the 69 - 70 STANDARD Cougar. This main harness connects to the harness for the convenience lights on the warning light panel in the center of the dash. Ford part number C9WY-10C877-C. Used in conjunction with the two convenience light harnesses / sockets found here. The convenience package was offered on Cougars that were non-XR7.

Used front side marker lens for the 1969 Mercury Cougar or Ford Mustang. This lens will be in good shape with no cracks or breaks.

Reproduction master power window switch that goes along with the power window conversion kits. Keep in mind we will buy your old usable factory parts. You might be surprised what those left over clips and wiring harnesses are worth!  Installing this master switch allows you to keep the original look of the crank handles, but allows the driver to control all four windows. All wiring and connectors are included.  ...

This two part black box is what encapsulates your sequential unit for all years 1969-1973. This of course will work with our reproduction sequential unit as well. This box was designed hang from a hook that is welded to the trunk floor just behind the driver side wheel well. *NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's and is the designer of all of our solid state...

Good used part cut from the trunk of a 69-73 Mercury Cougar. This hook is concealed under the trunk mat and suspends the sequential unit over the trunk drop off area on the driver side. *NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's and is the designer of all of our solid state sequential systems. There is no question he cannot answer! Here is a link to a great source of...

This new version sequential box works with either standard or plasma LED bulbs NOTE: Although your existing emergency flasher might work just fine with the new sequential unit, it is highly recommended that you also use the same updated electronic sequential flasher in its place to guarantee proper operation. This is a direct fit replacement, just pop open your black plastic box located in the driver side trunk drop off and plug it in. Your January 1970 and newer Cougar will have...

This is a "better quality" non-concours starter solenoid. It's just one step above our "generic" solenoid also listed on our site. An inexpensive replacement if you are not worried about being 100% correct. More often than not, these lower quality solenoids fail within a year or two so we always recommend buying original FoMoCo. Replaces Ford part # B6AZ-11450-A, C7AZ-11450-A & D2AF-11450-A.Cougar Applications:1967 Mercury Cougar1968 Mercury Cougar1969 Mercury Cougar1970 Mercury...

Used engine lift hook or hoist bracket for all 1969-70 351W engines from any Mercury Cougar or Ford Mustang. Ambidextrous, fits either side as long as you use factory cast iron exhaust manifolds. H code 351W-2V and M code 351W-4V engines. The factory used these hooks for installation of the engines into the cars on the assembly line. Nice detail to include for judged shows, many of these have been lost for various reasons. Sold individually, two needed per car, one on each side.We also sell...

Used engine lift hook or hoist bracket for all 1968-69 390 engines from any Mercury Cougar or Ford Mustang. Ambidextrous, fits either side as long as you use factory cast iron exhaust manifolds. X code 390-2V, S code 390-4V, and W code 427-4V engines. The factory used these hooks for installation of the engines into the cars on the assembly line. Nice detail to include for judged shows, many of these have been lost for various reasons. Sold individually, two needed per car, one on each side.We...

Used oil filter adapter from any 1968-70 Ford with 390 or 428CJ (non SCJ). Fits Cougar, Mustang, Torino, Fairlane, Cyclone, Ranchero, etc. Nice cast aluminum bracket for installing the spin on oil filter and oil pressure sending unit. Ford casting number C8AE-6881-A. Will fit 1967 FE engine blocks too. Those technically used an adapter with a casting number of C0AE-6881-A.

Reproduction oil filter adapter from any 1968-70 Ford with 390 or 428CJ (non SCJ). Fits Cougar, Mustang, Torino, Fairlane, Cyclone, Ranchero, etc. Nice cast aluminum bracket for installing the spin on oil filter and oil pressure sending unit. Ford casting number C8AE-6881-A. Will fit 1967 FE engine blocks too. Those technically used an adapter with a casting number of C0AE-6881-A.

Featured in this kit are all the basic items you need to convert your small block 1969 Cougar or Mustang from a 20" wide radiator with a fixed four blade fan to a 24" wide radiator with 3 cores and the MAXIMUM cooling big block, high performance 7 blade clutch fan. This setup was used on the highest horsepower drive-trains of the day including the Legendary 427 Side-Oiler equipped GTE and the 428 SCJ Drag-Pak equipped Cougars and Mustangs. This might sound like overkill for your small block...

NOTE: WE SUGGEST LOCAL PICK UP ONLY FOR CORE ENGINE BLOCKS BECAUSE WE CANNOT GUARANTEE BLOCKS WILL NOT HAVE CRACKS INTERNALLY. Long block, factory H code 351-2V V-8 engine. 351 Windsor engine rated at 250 Hp with 9.5:1 compression ratio in 1969. Likely 0.030" bored motor that may or may not have been in running condition when pulled. Guaranteed to be rebuildable. Complete engine less carburetor, distributor, exhaust manifolds, fan, accessories, pulleys, and flex plate. Intake manifold and oil...

NOTE: WE SUGGEST LOCAL PICK UP ONLY FOR CORE ENGINE BLOCKS BECAUSE WE CANNOT GUARANTEE BLOCKS WILL NOT HAVE CRACKS INTERNALLY. Long block, factory M code 351-4V V-8 engine. 351 Windsor engine rated at 290 Hp with 10.7:1 compression ratio in 1969. Likely 0.030" bored motor that may or may not have been in running condition when pulled. Guaranteed to be rebuildable. Complete engine less carburetor, distributor, exhaust manifolds, fan, accessories, pulleys, and flex plate. Intake manifold and oil...

NOTE: WE SUGGEST LOCAL PICK UP ONLY FOR CORE ENGINE BLOCKS BECAUSE WE CANNOT GUARANTEE BLOCKS WILL NOT HAVE CRACKS INTERNALLY. Dated 7C29 March 29, 1967.  Used standard bore 4.05" Ford 390 engine block. Will be used, dirty, have measurable taper, and will have a ridge. Good for rebuild. Bare block, may have C6ME, C7ME, castings. When we have them in stock we will post the casting date or dates. Heavy, will require either local pickup or freight shipping.  This item cannot ship...

This block has been professionally hot tanked and mag checked. No cracks. Dated 7C16 March 16, 1967.  Used standard bore 4.05" Ford 390 engine block. Will be used, dirty, have measurable taper, and will have a ridge. Good for rebuild. Bare block, may have C6ME, C7ME, castings. When we have them in stock we will post the casting date or dates. Heavy, will require either local pickup or freight shipping.  This item cannot ship through any conventional methods (USPS, UPS etc). Along...

NOTE: WE SUGGEST LOCAL PICK UP ONLY FOR CORE ENGINE BLOCKS BECAUSE WE CANNOT GUARANTEE BLOCKS WILL NOT HAVE CRACKS INTERNALLY. Dated 6L15, November 15, 1966.  Used standard bore 4.05" Ford 390 engine block. Will be used, dirty, have measurable taper, and will have a ridge. Good for rebuild. Bare block, may have C6ME, C7ME, castings. When we have them in stock we will post the casting date or dates. Heavy, will require either local pickup or freight shipping.  This item cannot ship...

NOTE: WE SUGGEST LOCAL PICK UP ONLY FOR CORE ENGINE BLOCKS BECAUSE WE CANNOT GUARANTEE BLOCKS WILL NOT HAVE CRACKS INTERNALLY. Dated 7M27, December 27, 1967.  Used 0.030 over bore 4.080" Ford 390 engine block. Years ago, it looks to have been fresh machined, with new freeze plugs. No paperwork, bare block. Will be used, dirty. Good for rebuild or assembly, quality of machining unknown. Bare block, may have C6ME, C7ME, castings. When we have them in stock we will post the casting date...

NOTE: WE SUGGEST LOCAL PICK UP ONLY FOR CORE ENGINE BLOCKS BECAUSE WE CANNOT GUARANTEE BLOCKS WILL NOT HAVE CRACKS INTERNALLY. Dated 6C5, March 5, 1966.  Used 0.030 over bore 4.080" Ford 390 engine block. Bare block, no crank shaft. Will be used, dirty. Good for rebuild or assembly, quality of machining unknown. Bare block, may have C6ME, C7ME, castings. When we have them in stock we will post the casting date or dates. Heavy, will require either local pickup or freight...

These replacement "Yellowtop" ignition coils are copies of the original. Nice reproduction cosmetically and functionally. This is a very prominent piece and a must have when trying to detail your engine compartment properly. Replaces Ford part # B6A-12029-B.   Note, no decals are included. Check the website in related items.

Reproduction distributor cap for the 1967 - 1973 Mercury Cougar or Ford Mustang 

A needed part for giving your car a tune-up.

Reproduction Distributor Condensor for the 1967 - 1973 Mercury Cougar and Ford Mustang

Correct Autolite 45 spark plugs for all 1967-73 289/302/351W/390/428CJ engines. This is what Ford installed originally from the factory. BF32 crosses over to this spark plug. Typically these should have a electrode gap of 0.035", with either stock points or Pertronix ignition systems. Sold individually.

C8AF-12A022-A For all 1967 - 71 V-8 distributors. Concours correct head stamping. Brass plug for the stock Autolite distributors. Installs as shown.

Reproduction single port vacuum advance for most all 1967-71 Ford V-8 engines. Fits Ford's brand of Autolite and Motorcraft distributors found on all 1967-71 Mercury Cougar and V-8 Ford Mustangs.

Used Autolite Distributor for 1968 390-4V and 1968-69 428CJ for the Mercury Cougar, Cyclone or Ford Mustang, Torino.  Ford part number  C8OF-12127-D.  

Used core distributor for 1969 Mercury Cougar and Ford Mustang with H code 351-2V and aNY transmission. Core distributors will have correct stamping of C9OF-M. Original Ford part number C9OF-12127-M.

Used core distributor for 1969 Mercury Cougar and Ford Mustang with M code 351-4V and automatic transmission. Core distributors will have correct stamping of C9OF-T. Original Ford part number C9OF-12127-T.

This little device may not appear to be all that important, but it has a big job to do when your engine gets too hot. The threaded end looks a bit like an engine temperature sensor, and that's because it is. It's normally mounted on the intake manifold or engine block where it can sense coolant temperature.The three ports at the other end are for vacuum connections. One goes to manifold vacuum, another to carburetor vacuum, and the third goes to the vacuum advance on the distributor. At normal...

Ignitor 1 by Pertronix, effectively replaces your points and condenser from your Distributor. Works in all Ford Autolite distributors found in 1967-73 Mercury Cougar and V8 Mustangs with single point distributors. This is also called an electronic ignition conversion. There is also an upgraded Ignitor II available. -50F To 300F Working Temperature Range, 0-15,000 Rpm Range, This Easy To Install And Maintenance Free Electronic Ignition System Features Solid-State Electronics And Rotating Cobalt...

Ignitor II by Pertronix, effectively replaces your points and condenser from your Distributor. Works in all Ford Autolite distributors found in 1967-73 Mercury Cougar and V8 Mustangs with single point distributors. This is also called an electronic ignition conversion. Adaptive Dwell Control -  Dwell increases with RPM to provide an average of 4 times the available energy between 3000 and 5000 RPM and twice the available voltage at the plug. -50F To 300F Working Temperature Range,...

Powerful oil filled coil that generates 40,000 volts, designed to work with the either of our Pertronix Ignitors. Sold in black or chrome. *Note - This coil is not necessarily needed with the Pertronix Ignitors, the stock Ford coil works fine for most applications.

Powerful oil filled coil that generates 40,000 volts, designed to work with the either of our Pertronix Ignitors. Sold in black or chrome. *Note - This coil is not necessarily needed with the Pertronix Ignitors, the stock Ford coil works fine for most applications.

Concours correct Autolite spark plug wires for any 1969 Mercury Cougar or Ford Mustang with 428CJ engine with thermactor smog system. Black wires with 'Autolite', 'radio resistance', cylinder numbers individually imprinted, and dated 2Q68 (second quarter 1968) on the 7mm wires. Orange spark plug boots on this set.

Concours correct Autolite spark plug wires for any 1969-70 Mercury Cougar Eliminator or Ford Mustang with Boss 302 engines. Black wires with 'Autolite', 'radio resistance', cylinder numbers individually imprinted, and dated 2Q69 (second quarter 1969) on the 7mm wires. Orange spark plug boots on this set.

Concours correct Autolite spark plug wires for any 1969 Mercury Cougar Eliminator or Ford Mustang with 351W engines. Black wires with 'Autolite', 'radio resistance', cylinder numbers individually imprinted, and dated 2Q68 (second quarter 1968) on the 7mm wires. Black spark plug boots on this set.

Ford FE distributor shaft to engine block gasket, made of rubber. Fits all FE or 352, 360, 390, 410, 427, 428 engines. 1958-76. This is a tapered rubber washer. Will not fit small block Windsor or Cleveland engines. Ford part number B8A-12143-A.

New rubber "O" ring for Ford V-8 distributors from 289/302/351W/351C/429 engines.

Pertronix brand 7mm spark plug wires. These are performance oriented wires compared to the concours spark plug wires. For any 1967-73 Mercury Cougar and Ford with 289 or 302 engines. Black wires and boots, quality spark plug wires taylor made for the small block Ford engines. Recommended by Pertronix for use with the Flame Thrower coils.

Used core distributor for 1969 Mercury Cougar and Ford Mustang with S code 390-4V and automatic transmission. Core distributors will have correct stamping of C7AF-AC. Original Ford part number C7AF-12127-AC. Current unit has a date of 9B10, or February 10, 1969. Stamped C7AF-12127-AC.

The Proper ignition advance curve is vital for maximum performance, economy (gas mileage) and drive-ability. Ford / Mercury owners had few acceptable choices with regard to adjusting the vacuum curve with their OEM distributor. You could fumble with the stock washers, fiber stops and springs (a hit-or-miss exercise in frustration!) or you could spend the money on an adjustable after market vacuum advance that looks completely out of place and cost you major judging points. This works on any...

Replaces Ford Part Number: B7A-12200-A / DR-5 And C5TZ-12200-A / DR-87 (Service Replacement)

Reproduction coil mounting bracket. The manufacturer claims it fits all cars 1967-73. We happen to know that there are no less than 4 different versions of factory Ford coil brackets used on 1967-73 Mercury Cougar and Ford Mustangs and literally all other Ford cars and trucks. Some have the coil on top of the intake manifold, while some years and engines have the coil mounted to the front of one of the cylinder heads. To our knowledge this is the only reproduction style on the...

Reproduction replacement hold down clamp for the distributor on any 67 - 73 Cougar or Mustang. Sold individually, 2 needed per car.

Used distributor clamp and bolt, for any FE Engine: i.e. 352 / 360 / 390 / 410 / 427-4V / 428 / 428CJ / 428SCJ built from 1958-1976. Bolt may be used, or new from AMK Products. Ford part number B8A-12270-A.

Used distributor clamp with bolt, for any 260 / 289 / 302 / 351W / 351C / 429CJ built from 1963-1973. May come with either an original used bolt or the new bolt made by AMK Products. Ford part number C3AZ-12270-A.

Used ported vacuum switch with filter. Unique piece, unknown application, definitely found on a 1968. Current offering are dated 8-67, 6-68, 5-68, 7-69, 8-69. Original distributor vacuum advance control valve, also called a ported vacuum switch (PVS) valve, that was installed on all Ford models including Mercury Cougar, Ford Mustang, and Torino starting in 1967. This is a used original pot metal and brass part. It has the FORD oval logo and part number C8AE-A casting.This casting number is...

Exact copy reproduction concourse correct distributor cap with raised Autolite logo. Good for all 67 - 73 Cougars and Mustangs. A must have for anyone building a show car.

Distributor hold down bolt. All V-8 engines.1967-73 Mercury Cougar and Ford Mustang. 5/16 x 7/8" bolt, 1/2' hex head.

Used 1969 351W coil mounting bracket. This version of the bracket is specific on the 351W and allows extra room for the oil dipstick. We happen to know that there are no less than 4 different versions of factory Ford coil brackets used on 1967-73 Mercury Cougar and Ford Mustangs and literally all other Ford cars and trucks. Some have the coil on top of the intake manifold, while some years and engines have the coil mounted to the front of one of the cylinder heads. Listed in the...

Concours vacuum hose kit with colored stripes. Multiple pieces, connects carburetor, distributor, and thermal vacuum switch on the water neck. 1969-70 Mercury Cougar Eliminator with Boss 302 and 1969-70 Ford Mustang with Boss 302 engines.

Concours vacuum hose kit with colored stripes. Multiple pieces, connects carburetor, distributor, and thermal vacuum switch on the water neck. Fits all 1968-69 Mercury Cougar or Ford Mustang with S or X code engines. Additionally fits 1968-70 428 Cobra Jet engines. This kit is for the distributor vacuum advance units with single nipple connections. Often times it is the ones with manual transmissions, but not always.

Concours vacuum hose kit with colored stripes. Multiple pieces, connects carburetor, distributor, and thermal vacuum switch on the water neck. Fits all 1968-69 Mercury Cougar or Ford Mustang with S or X code engines. Additionally fits 1968-70 428 Cobra Jet engines. This kit is for the distributor vacuum advance units with dual nipple connections. Often times it is the ones with automatic transmissions, but not always.

Concours vacuum hose kit with colored stripes. Multiple pieces, connects carburetor, distributor, and thermal vacuum switch on the water neck. Fits all 1968-70 Mercury Cougar or Ford Mustang with 289, 302, and 351W engines. This kit is for the distributor vacuum advance units with single nipple connections. 

Concours vacuum hose kit with colored stripes. Multiple pieces, connects carburetor, distributor, and thermal vacuum switch on the water neck. Fits all 1968-70 Mercury Cougar or Ford Mustang with 289, 302, and 351W engines. This kit is for the distributor vacuum advance units with dual nipple connections. 

Concours vacuum hose kit with colored stripes. Multiple pieces, connects carburetor, distributor, and thermal vacuum switch on the water neck. Fits all 1970-73 Mercury Cougar or Ford Mustang with 351C or cleveland engines. Distributor vacuum advance units with single nipple connections. Often times it is the ones with manual transmissions, but not always.

Concours vacuum hose kit with colored stripes. Multiple pieces, connects carburetor, distributor, and thermal vacuum switch on the water neck. Fits all 1970-73 Mercury Cougar or Ford Mustang with 351C or cleveland engines. Distributor vacuum advance units with dual nipple connections. Often times it is the ones with automatic transmissions, but not always.

Concours correct Autolite spark plug wires for any 1969 Mercury Cougar Eliminator or Ford Mustang with 390 or 428CJ engines. Black wires with 'Autolite', 'radio resistance', cylinder numbers individually imprinted, and dated 2Q68 (second quarter 1968) on the 7mm wires. Black spark plug boots on this set.

Reproduction dual port vacuum advance for most all 1968-70 Ford V-8 engines. Very close replica of the factory installed vacuum advance. This version has two pressed in brass fittings for vacuum hoses. This working vacuum advance will need to have your threaded plug installed in the port end. OEM Ford units had gold colored bands instead of this silver band as shown. This unit very closely matches the 1970 vacuum advance, the earlier vacuum advances had one of the vacuum fittings that screwed...

Reproduction upper distributor bushing for many V-8 engines 1958 through 1973. All 289 distributors 1965-67 should have one installed, 302's up until 1973 or possibly later. All FE distributors, including 352, 390, 410, 427, 428.  * Note - 351W and 351C engines and 429/460 engines used a different upper bushing. See related items for that listing. Replaces Ford part number B8QH-12120-A. We measure 0.687" O.D., 0.468" I.D., and 1.750 long. ...

Reproduction upper distributor bushing for 1969-73 351W, 351C, 429, and 460 Ford V-8 engines. * Note - 260/ 289 / 302 / 352 / 390 / 410 / 427 / 428 engines, all used a different upper bushing. See related items for that listing. Replaces Ford part number  C5AZ-12120-A. We measure 0. O.D., 0." I.D., and 1.750 long.

Key stock for 1967-73 Ford V-8 engines 3/16" square straight keys. Ships in 4 inch lengths, cut to fit the different applications. Common sizes 289/302 1-13/32", 351 1-3/4", etc.

Includes all X code 390-2V, S code 390-4V, GT-E W code 427, and 428 Cobra Jet engines for 1968-70 only. The C8AE-6316-A harmonic balancer is identified by the 3 bolt holes for attaching the crankshaft pulley. Outside diameter is approximately 7 inches, 1-1/16 inches thick and has the timing marks on rim. Refundable $50.00 core charge when a rebuildable C8AE-6316-A harmonic balancer is received by WCCC. Ford part # C8AZ-6316-B, Ford casting # C8AE-6316-A.*NOTE* Excludes 1967 S code 390-4V...

B8AZ-6359-A Crankshaft or dampener spacer for any FE Ford engine. 1965 - 1971 Ford or Mercury crankshaft spacer 352, 390, 427, 428, all FE engines. Used spacer, will show a little wear from the outside seal. 

Usually ships in 3-5 business days. 1969 3 bolt crankshaft pulley provision. No casting number works well for a non concours engine. 351 Windsor engine only. No casting numbers, has imprinted timing marks and numbers like original.

C9ZE-6316-B 1969 G code Boss 302 Eliminator and Mustang only. Ford casting number C9ZE-6316-C is also acceptable. Outside diameter is approximately 6-1/2 inches. Ford master part number C9ZZ-6316-B. Crankshaft balancer, crank-shaft dampener, harmonic balancer. If you have a rebuildable core 1969 Boss 302 balancer to trade, we can offer a substantial discount off of the retail price.  Notice the rubber on this one is unusually nice. *Note - Excludes 1970 Boss 302 and all non-Boss...