All Available Parts - 1969 Mercury Cougar

A quality rust proof stainless steel cable which features all the correct hardware. Sold as a pair. Replaces Ford Part #: C9ZZ-7652806-A.

This is a freshly rechromed / plated pair of used xr7 convertible boot trim mouldings.  Prior to being restored these parts were good used parts, not heavily pitted parts. Keep in mind the price shown here goes down substantially if you have one or more extra (in addition to the complete set from your car) good quality cores to trade in. If you have xr7 cores to sell lets us know! The casting numbers as seen on the bottom of these boot moulding, hockey stick shaped trim is C9WB-76423A18-B...

Used grade "B" driver side (left hand) convertible top boot moulding / trim for the Mercury Cougar XR7 convertible. These are unique to the XR7 as the standard convertibles used the shorter version (same as Mustang) that ended at the quarter window. We are often asked, "Why so much?" The answer is that the production figures for these XR7's were very low and most folks will consider restoring them in just about any condition. When we do get in a XR7 convertible parts car (every few years or...

*NOTE: This item comes un-painted from the manufacturer.Very correct reproduction of an impossible to find part. The only difference I can detect is that this original weighs just an ounce or two more than the original. Click on images to enlarge. Customer feedback found at mercurycougar.net: Boy service is just not the same as the "good old"? days. I ordered a half a trunk load of parts and pieces from West Coast Classic Cougar and about 2 hours later got a phone call informing me that the...

*NOTE: This item comes un-painted from the manufacturer.Another spot on reproduction! Correct for CJ and SCJ.  Comes with brackets and hardware as shown. Click on images to enlarge. ...

Air cleaner pre-heater paper hose. Should fit most applications from 1970-73 Mercury Cougar and Ford Mustang with V8 engines. 2 inch inside diameter, we cut these to about 9 inches long. Correct black paper outside, flexible paper tube, kind of like a Slinky. Please verify your needed length, we leave them a bit longer than needed so that they fit more than one application.

Exhaust manifold bolt / stud for mounting the heat shield on the passenger side. This is the longer of the two stud bolts. See item 41350 for the short heat shield bolt. For all Mercury Cougar or Ford Mustang, Torino, Cyclone, etc. with Q or R code 428 cobra Jet engines with factory cast iron exhaust manifolds. We also sell the complete bolt kit for the CJ exhaust manifolds. 382803-S

These are bolted to the rear frame rails and were used to tie the car down to the transporter for the journey from the factory to the dealer. The dealer was supposed to remove them and return them for a credit as instructed by the dealer. Notice the sticker on the rear license plate frame (decal is available in the decal section)? Many sets slipped through as the dealers often forgot or did not deem the small credit back worth their effort to remove. These are great for transporting your car...

Attaches to the lower front portion of the front fender. Good used brace that may be lightly rusted but not ripped, but will almost always show minor repairs. Fits passenger and driver side. Most often they will have the J-nut still installed on both ends.Ford master part # C9WY-16B134-A.

Good used L bracket that is not heavily rusted or bent. Passenger side is marked from the factory with an "R" and driver side is marked with an "L". The portion with the lip mounts vertically and the purpose of the lip is to align the splash shield into the proper location.

Good used L bracket that is not heavily rusted or bent. Passenger side is marked from the factory with an "R" and driver side is marked with an "L". The portion with the lip mounts vertically and the purpose of the lip is to align the splash shield into the proper location.

Coil hood hinge spring, 5-13/32" in overall length, 14 coils, coil diameter 1.899 inches. Sold individually, one per side. Other applications include:  1967-69 Mercury Cougar1967-70 Ford Mustang1965-69 Torino, Fairlane, Ranchero1965-70 Falcon 1965-66 Falcon Ranchero Ford part # C3OZ-16789-A. You can find the hood hinge apron nuts here.Anghel Restorations offers a very detailed breakdown of the differences in the Cougar and Mustang hood hinges. ...

Reproduction hood hinge spring for all 1967-69 Mercury Cougars and 1964-70 Ford Mustangs. Common on many Ford and Mercury cars, this spring has 14 coils like the originals. We've found these springs to be of lesser quality than the originals, and they will stretch over time and not hold the hood up very well. We highly recommend you stick with original OEM springs. No returns on these springs. Click here to see our listing for good used originals. Replaces Ford part # C3OZ-16789-A. You can...

C9ZB-7653139-A is the part number for the drivers side, C9ZB-7653138-A for the passenger side. These will often break when one hydraulic lift cylinder malfunctions and the other is still working. This scenario will put the top frame in a bind causing one of these cast parts to break. We carefully inspect these before shipment for cracks, worn areas or corrosion.

Keep in mind we also have these in used form. for a little more (or less) money depending on condition. This part fits all Mustangs and Cougars 1965 - 1970. Replaces Ford Part #: C5ZZ-7650509-K. Casted Pot Metal with Engineering # C4ZB-7650535-C

Keep in mind we also have these in used form. for a little more (or less) money depending on condition. This part fits all Mustangs and Cougars 1965 - 1970. Replaces Ford Part #: C5ZZ-7650508-KCast Pot Metal with Engineering # C4ZB-7650534-C

No damage original bolt. Sold individually, two required per car.

Usually ships in 3-5 business days. Replaces Ford Part #: C4DZ-7653337-A. This is a new part, not a rebuild, no core needed. Correct brackets for a Cougar, not a generic one size fits all application. 5 year warranty when used with automatic transmission fluid.

Exact fit, not generic 'One Size Fits All' hoses. Quality high pressure fittings. Contains both the upper and lower Hydraulic Hose for a 1969 or 1970 Mercury Cougar or Ford Mustang Convertible Hydraulic Cylinder.

Not quite as long as the original bushing, but will work. If you want the correct one, we occasionally get in the NOS version of this bushing. Call us for the availability of the NOS bushing. Replaces Ford Part #: C3AZ-5422841-A.

Good used plastic trim that will need repaint, and the screw hole hidden behind dash pad is almost always cracked.Ford Part #: C9ZZ-7603598-A, stamped with C9ZB-7603598-AW-R.H. This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit of 50% of our web price for parts delivered in hand or by carrier to our Brooks, Oregon location. If you're not interested in store credit, just shoot us an...

Good used plastic trim that will need repaint, and the screw hole hidden behind dash pad is almost always cracked.Ford Part #: C9ZZ-7603599-A, stamped with C9ZB-7603599-AW-L.H. This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit of 50% of our web price for parts delivered in hand or by carrier to our Brooks, Oregon location. If you're not interested in store credit, just shoot us an...

C5AZ-7630702-A Ashtray receptacle for 1969-70 Mercury Cougar and Ford Mustang. Only the rear door panel ashtrays in the back seat area. Receptacle only, sliding covered retainer sold separately. Also fits 1965-68 Ford and Mercury full sized convertibles. Decades old gum stuck to the bottom is no extra charge...

Convertible top switch for all 1969 Mercury Cougar standard and XR7, 1970 standard Cougar (76A), all 1969-70 Ford Mustang. This switch is located over the radio bezel. Very nice reproduction item, comes as shown with the knob marked "TOP". *Note - The 1970 Mercury Cougar XR7 had the power top switch located in the convenience switch panel in the dash.

New pair of weld in shock tower reinforcement plates cut from 11 gauge steel (1/8") for the Mercury Cougar or Ford Mustang. It is common knowledge that one of the main design flaws of the early Cougar or Mustang are the shock towers. Because of this design flaw, it is common (even with pampered, low mile, completely stock cream puffs) for the shock towers to have some degree of cracking as they were never designed to fit an oversized wheel and tire package, be cornered hard or handle the heavy...

Connecting to the Convertible Frame Lift Lever and the Convertible Hoses, the Convertible Top Hydraulic Cylinder creates pressure from the fluid transferred by the hoses. Each Hydraulic Cylinder consists of light-weight aluminum casing, a durable steel rod, and includes all bushings and gaskets. Part is made through innovative engineering and rigorously tested to provide you with the best in functionality and long-term dependability.  Precisely crafted with high grade materials...

Galvanized three piece replacement tack strips for the 1969 - 1970 Cougar convertible. Over-sized, must be shipped via UPS.

This original part has been reinforced to brace the front frame rails / tie together lower control arm pivots in a superior way to the original design. This design will prevent any camber change in hard cornering. This is not needed for the average Cougar owner but if you are desiring to make your car a "Handling Machine" every bit counts and this is an inexpensive upgrade. These crossmembers are welded in house, and will be unpainted bare metal. This combined with our shock tower...

We have found a new manufacturer of the convertible top boots that fit much better than the boots we were previously selling. See Pics Below. Ford calls this part the "folding top dust hood". Made from original pattern. Features long lasting vinyl. Includes foam pads. We stock the black and white. All other colors are ordered on demand from the manufacturer. Please note that convertible boots never came from the factory with snaps (except the 6 on the interior panels), so any boot that comes...

We have found a new manufacturer of the convertible top boots that fit much better than the boots we were previously selling. See Pics Below. Ford calls this part the "folding top dust hood". Made from original pattern. Features long lasting vinyl. Includes foam pads. We stock the black and white. All other colors are ordered on demand from the manufacturer. Please note that convertible boots never came from the factory with snaps (except the 6 on the interior panels), so any boot that comes...

We have found a new manufacturer of the convertible top boots that fit much better than the boots we were previously selling. See Pics Below. Ford calls this part the "folding top dust hood". Made from original pattern. Features long lasting vinyl. Includes foam pads. We stock the black and white. All other colors are ordered on demand from the manufacturer. Please note that convertible boots never came from the factory with snaps (except the 6 on the interior panels), so any boot that comes...

We have found a new manufacturer of the convertible top boots that fit much better than the boots we were previously selling. See Pics Below. Ford calls this part the "folding top dust hood". Made from original pattern. Features long lasting vinyl. Includes foam pads. We stock the black and white. All other colors are ordered on demand from the manufacturer. Please note that convertible boots never came from the factory with snaps (except the 6 on the interior panels), so any boot that comes...

We have found a new manufacturer of the convertible top boots that are supposed to fit much better than the boots we were previously selling. See Pics Below. Ford calls this part the "folding top dust hood". Made from original pattern. Features long lasting vinyl. Includes foam pads. We stock the black and white. All other colors are ordered on demand from the manufacturer. Please note that convertible boots never came from the factory with snaps (except the 6 on the interior panels), so any...

Keeper or retainer for attaching the convertible top cylinder pins. These are usually broken when replacing convertible top cylinders. One retainer per side.Ford Part # 372552-S These are not a exact replica of the t-bolt retainer, but will work for a replacement for the retainer on the T-bolt on the door windows (T-bolt Ford Part # C8SZ-6523274-A).  Ford part number for the retainer is C7SZ-65234A28-A.

Used 2 hole front mount center bracket for the sun visors in the 69 - 70 Mercury Cougar or 68 - 70 Ford Mustang convertible. The Master Parts Catalog (MPC) shows a specific part for the convertibles, but we have found three different styles of the sun visor arm clips used in the 68 - 70 convertibles.  Casting# C8OB-6304132-A has no dividerCasting# C8ZB-6504132-A has a partial divider (Most Common)Casting# C8ZB-6504132-B has a complete divider.  The colors don't always...

This harness connects the convertible top motor to the under dash convertible top harness under the dash. Fits 1969-70 Mercury Cougar and 1969-70 Ford Mustang. This wire rests in the trough under the passenger side sill plate and goes behind the back seat where the convertible top pump is located.Ford part number C9ZB-15A668-B.

This black wire attaches to the Circuit Breaker coming off the starter solenoid on one end then passes through the firewall to mate with the top switch wiring harness at the other end. We believe that some 1969 harnesses may have used a fusible link wiring harness in place of this one. This harness and the circuit breaker can be used on those applications.Ford part number C9ZB-15A669-B or C9ZZ-15A669-B.

This black wire attaches to the fusible link. The Fusible link connects to the starter solenoid with an eyelet connector, then connects to this wire with a billet connector. This wire then passes through the firewall to mate with the power top switch wiring under the dash. Correct for both XR7, Standard convertibles and power sunroof equipped Cougars in 1969, and Standard Cougar Convertibles in 1970.Casting Number: C9ZB-15A669-BFord Part Number: C9ZZ-15A669-BFits: 1969 Mercury Cougar Standard...

This fusible link is a section of wire connecting the starter solenoid on one end and wiring harness that passes through the firewall to mate with the top switch wiring. Correct for power sunroof equipped Cougars. May also work for XR7 and Standard convertibles.

Used grommet for protecting the trunk light wiring as found on 1967-70 Mercury Cougar and Ford Mustangs. Ford part number C4AB-14603-A.

Exhaust manifold bolt / stud for mounting the heat shield on the passenger side. This is the shorter of the two stud bolts. See item 31171 for the short heat shield bolt. For all Mercury Cougar or Ford Mustang, Torino, Cyclone, etc. with Q or R code 428 cobra Jet engines with factory cast iron exhaust manifolds. We also sell the complete bolt kit for the CJ exhaust manifolds. 

Since we have a difficult time keeping grade "A" Windsor heat shields in stock we also offer a driver quality version. This unit will be very thin from rust in certain areas. C9OZ-9A603-A Metal shroud and tube assembly that attaches to the factory 1968-1969 air cleaner assembly on all 351 Windsor engines both H code 351-2V and M code 351W-4V (1969 offering only). *Note - for 1970 this shield is used after build date of 2-2-1970, but could be used on prior dates. We suspect that the early 2...

This used header will not be perfect as you can see from the pictures but it can be restored with some TLC. The part you get will be solid, we will not send you junk.Ford casting number C9ZB-76514A72-A

This is the storage bag that the convertible top cover folds into when the top is in the down position. Ford calls this part the "Folding top dust hood container." It is made from common vinyl top material and is always black. It measures 15"x27" and the bottom portion is sometimes, tapered down to 8". The same design was used for many Ford Products of the day including Torino, Montego and others. Current offering does not have a tapered bottom, it is square. Pictures will show both styles...

This pair of plates cut from 11 gauge steel (1/8") are designed to be welded onto the front crossmember that braces the front frame rails and ties together the lower control arm pivots in a superior way to the original design. When welded onto the front crossmember properly, these plates will prevent any camber change in hard cornering. This is not needed for the average Cougar owner, but if you are desiring to make your car a "Handling Machine", every bit counts. This combined with our shock...

Used passenger side (right hand) convertible top boot moulding / trim for the Mercury Cougar or Ford Mustang convertible. No cracks or missing studs, driver quality chrome. We also have some that need re-chrome as well as some singles, please call for details. Due to the difficulty in obtaining trim we no longer sell these without first having you send us your cores.*NOTE* If you have questions about your cores, checkout our video below. ...

Due to the difficulty in obtaining trim we no longer sell these without first having you send us your cores. Restored driver side (left hand) vertical windshield moulding / trim for the Mercury Cougar or Ford Mustang convertible. If your stainless parts have no real damage you may consider investing in a free standing buffer and polishing kit. When you purchase one of our stainless trim parts you are paying for the removal of dings and scrapes as well as the polishing of the part.  Ford...

Due to the difficulty in obtaining trim we no longer sell these without first having you send us your cores. Restored passenger side (right hand) vertical windhield moulding / trim for the Mercury Cougar. If your stainless parts have no real damage you may consider investing in a free standing buffer and polishing kit. When you purchase one of our stainless trim parts you are paying for the removal of dings and scrapes as well as the polishing of the part.  Ford part # C9ZZ-7603144-B....

Restored exterior driver side (left hand) header moulding / trim for the Mercury Cougar or Ford Mustang convertible. Due to the difficulty in obtaining trim we no longer sell these without first having you send us your cores. *NOTE* These do not pry off! The fasteners are located on the bottom side. If your cores are missing studs then you will receive like parts in exchange. The studs can be reattached to the bottom side so do not discard those lose parts! If you have questions about your...

Restored exterior passenger side (right hand) header moulding / trim for the Mercury Cougar or Ford Mustang convertible. Due to the difficulty in obtaining trim we no longer sell these without first having you send us your cores. *NOTE* These do not pry off! The fasteners are located on the bottom side. If your cores are missing studs then you will receive like parts in exchange. The studs can be reattached to the bottom side so do not discard those lose parts! If you have questions about your...

Excellent quality reproduction sun visor assemblies and corner trim for the convertible 1969 - 1970 Mercury Cougar or Ford Mustang. These feature the correct satin finish, fit perfect and look spot on. Sold as a pair, the original passenger side part has a C9ZB-7604122-C casting number on the back side and the driver side reads C9ZB-7604123-C. These will also interchange with versions ending in A B or D. Later versions will show one less screw tab. Replaces Ford part # C9ZZ-7604144 /...

Used driver side (left hand) exterior windshield pillar post moulding for the Mercury Cougar. Sold on an exchange basis only. If your stainless parts have no real damage you may consider investing in a free standing buffer and polishing kit. With a bit of elbow grease and time, you can make those trim pieces look better than new! Due to the difficulty in obtaining trim we no longer sell these without first having you send us your cores. *NOTE* If you have any questions about your cores,...

Restored passenger side (right hand) exterior windshield pillar post moulding for the Mercury Cougar. Sold on an exchange basis only. If your stainless parts have no real damage you may consider investing in a free standing buffer and polishing kit. With a bit of elbow grease and time, you can make those trim pieces look better than new! Due to the difficulty in obtaining trim we no longer sell these without first having you send us your cores. *NOTE* If you have any questions about your...

Used exterior driver side (left hand) header moulding / trim for the Mercury Cougar or Ford Mustang convertible. If your stainless parts have no real damage you may consider investing in a free standing buffer and polishing kit. With a bit of elbow grease and time, you can make those trim pieces look better than new! Due to the difficulty in obtaining trim we no longer sell these without first having you send us your cores. *NOTE* These do not pry off! The fasteners are located on the bottom...

Used exterior passenger side (right hand) header moulding / trim for the Mercury Cougar or Ford Mustang convertible. If your stainless parts have no real damage you may consider investing in a free standing buffer and polishing kit. With a bit of elbow grease and time, you can make those trim pieces look better than new! Due to the difficulty in obtaining trim we no longer sell these without first having you send us your cores. *NOTE* These do not pry off! The fasteners are located on the...

Ashtray sliders for the rear interior quarter panels in the 1969 or 1970 Mercury Cougar or Ford Mustang.  Slide handle is ribbed black plastic and has ribbing for strength on the slide cover on this reproduction.Not exactly concours, but a close copy. See the comparison photo. Replaces Ford part # C1AB-7630714-A.

Metal strip that fastens the weatherstrip to the bottom side of the header bow.

Used driver side (left hand) lower windshield moulding / trim for the Mercury Cougar or Ford Mustang. These are the same as the coupe, but the convertible piece has about an inch - inch and a half cut off the end. Because these mouldings are used original pieces, they will have far superior fit when compared to "offshore" reproductions that do not fit correctly and just plain old look like crap. These are used pieces and will be showing only minor dents, dings, dullness, or scratches. They are...

Used passenger side (right hand) lower windshield moulding / trim for the Mercury Cougar or Ford Mustang. These are the same piece as the coupe, however the convertible piece has about an inch - inch and a half cut off the end. Because these are used original pieces, they will have far superior fit when compared to "offshore" reproductions that do not fit correctly. These are used pieces and will be showing only minor dents, dings, dullness, or scratches. They are a great option for those of...

Restored driver side (left hand) lower windshield moulding / trim for the Mercury Cougar or Ford Mustang. This unit is basically the same as the coupe version, but this convertible unit has about and inch and a half cut off the end. Because these lower windshield mouldings are lovingly restored original pieces, they will have far superior fit and finish when compared to "offshore" reproductions that do not fit correctly and just plain old look like crap. They are an excellent option for you...

Restored passenger side (right hand) lower windshield moulding / trim for the Mercury Cougar or Ford Mustang. This unit is basically the same unit as the coupe, but this convertible piece has about an inch and a half cut off the end. Because these side lower windshield mouldings are restored original pieces, they will have far superior fit and finish when compared to "offshore" reproductions that do not fit correctly. This package is also an excellent option for you Mustang owners as well....

Reproduction tack strip for the rear bow of the convertible top on the Mercury Cougar or Ford Mustang convertible. When replacing your convertible top, it's also a good idea to replace the tack strips in the front and rear bows of the convertible top frame. This strip slips into the rear bow of the convertible top's frame and allows the fabric of the top to be attached to the frame. You will need approximately 5 Feet (60 inches) of material and will have to trim to fit your top. You can also...

Reproduction front tack strip for the front bow of the convertible top on the Mercury Cougar or Ford Mustang convertible. When replacing your convertible top, it's also a good idea to replace the tack strips in the front and rear bows of the convertible top frame. This strip slips into the front bow of the convertible top's frame and allows the fabric of the top to be attached to the frame. You will need approximately 5 feet (60 inches) of material and will have to trim the tack strip to fit...

14 piece bolt and screw set used to attach the convertible tack strip to the body. Kit comes with (12) 7/16 bolts and (2) phillips head screws. 

Used convertible top switch for all 1969 Mercury Cougar standard and XR7, 1970 standard Cougar (76A), all 1969-70 Ford Mustang. This switch is located over the radio bezel. Used and tested convertible top switch, it will not come with a knob, sold separately. This switch was also used on Cougars with factory power sunroofs. *Note - The 1970 Mercury Cougar XR7 had the power top switch located in the convenience switch panel in the dash. ...

Used driver side (right hand) convertible top boot moulding / trim for the Mercury Cougar or Ford Mustang convertible. No cracks or missing studs, driver quality chrome. We also have some that need re-chrome as well as some singles, please call for details. Due to the difficulty in obtaining trim we no longer sell these without first having you send us your cores.*NOTE* If you have questions about your cores, checkout our video below. ...

This is the restored stainless steel trim for the front of the boot that attaches to the back side of the back seat in a 1969 or 1970 Cougar and Mustang. This is a very hard part to come by in good shape. Many times body shops will lose this piece while replacing the top.Ford part number: C9ZZ-7654676-ATHIS ITEM WILL NOT SHIP UNTIL WE HAVE RECEIVED YOUR CORE. ...

Used power convertible top pump, motor and reservoir for the Mercury Cougar or Ford Mustang convertible. We do offer an excellent reproduction which you can get right here, but nothing beats original FoMoCo. There is a difference in the space of the mounting bracket between the 1969-70, and 1971-73 Cougar or Mustang convertible top pump assemblies. Not to be interchanged.Our pumps are tested, we recommend flushing the pumps and reservoirs prior to installation. Save your grounding wire,...

Ground wire for convertible pump motor. Short wire section that attaches to the pump motor and grounds to the chassis of any 1969-73 Mercury Cougar or Ford Mustang. Easy to copy, #10 gauge wire about 11-1/2 inches long. Two ring terminals attached. Easy peasy.

Reproduction tips and screws for your convertible top welt. It's the strip that goes across the top back side of the convertible top. These are the decorative tips that go on each end of the welt.Each kit includes two tips and two screws.

Restored driver side (left hand) convertible top boot moulding / trim for the Mercury Cougar XR7 convertible. These are unique to the XR7 as the standard convertibles used the shorter version (same as Mustang) that ended at the quarter window. We require you send a restorable core in exchange in advance to get this pricing. If your part is missing the aluminum belt-line weatherstrip mount then the part you receive in exchange will also be missing it.Ford part # C9WB-76423A19-A. ...

Restored Passenger side (right hand) convertible top boot moulding / trim for the Mercury Cougar XR7 convertible. These are unique to the XR7 as the standard convertibles used the shorter version (same as Mustang) that ended at the quarter window. We require you send a restorable core in exchange in advance to get this pricing. If your part is missing the aluminum belt-line weatherstrip mount then the part you receive in exchange will also be missing it. Casting # C9WB-76423A18-B. ...

Reproduction 21 pc installation screw kit to install the well liner on your 69 - 70 Convertible Cougar or Mustang.

This listing is for all four pieces restored as shown, sold on an exchange basis only. The Standard differs from XR7 on the Cougar in that the XR7 boot trim extended all the way to the door and the Standard uses the Mustang trim and ends at the quarter window.

Reproduction stainless steel trim for the front of the boot that attaches to the back side of the back seat in a 1969 or 1970 Cougar and Mustang. Ford part number: C9ZZ-7654676-A

Detachable mounting plate for installing the driver side convertible ram cylinder, to the convertible top frame assembly behind the quarter interior panel. Right and left are the different, fits all 1969-70 Mercury Cougar and 1965-70 Ford Mustang convertibles. Ford part number C5ZZ-76531A19-A.

Rare to find a diecast ash tray lid with no pitting. This design was used on several convertibles 1964 - 1970 starting the Ford Galaxie. The casting number on the back reads C4AB-7630706.

 Like most examples you will see out there this grade B sliding lid will have minor pitting. This design was used on several convertibles 1964 - 1970 starting the Ford Galaxie.  The casting number on the back reads C4AB-7630706.

Reproduction C5AZ-7630702-A Ashtray receptacle for 1969-70 Mercury Cougar and Ford Mustang. Only the rear door panel ashtrays in the back seat area. Slightly deeper than the OEM ash trays, plenty of room for installation. Receptacle only, sliding covered retainer sold separately, find it here. Also fits 1965-68 Ford and Mercury full sized convertibles. 

Rear most convertible top bow #4, from a 1969-70 Mercury Cougar or Ford Mustang convertible top assembly. This is the last bow and would have had a tack strip attached. Bow only, slat brackets sold separately. Ford part number C9ZZ-7651278-A.

Slat or pivot bracket for attaching the #4 rear most bow on a 1969-70 convertible top. Sold individually, one for each side needed for installation. Bushing is normally broken or missing, plan on sourcing or making a replacement bushing for the pivot. Ford part number C9ZZ-7650340-A.

Bolt for the under side convertible plate on any 1969-73 Mercury Cougar or Ford Mustang. 6 total bolts needed for attaching reinforcement plate to undercarriage. Sold individually. These are a close match to the original bolts, which are 3/8-16 x 1-1/2". Ford tightening specs. are 25-38 lbs. ft. torque.Replaces Ford number 57048-S2.

C5ZZ-7610962-A Ford description of this plate is "Plate - Front floor lower cross member". All 1969-73 Cougar convertibles and all 1965-73 Ford Mustang convertibles use this plate. Bolts into place with 6 hex bolts 3/8-16 x 1-1/8" with washers. These were painted satin black from the factory. Some time between 1969 and 1973 this plate underwent a revision by Ford. We are going to split by generation. 1969-70 plates are flat on one edge. 1971-73 has a slight hump or bend. Either works and...

Must have for 69-70 convertible owners or anyone else who wishes to tighten up the notoriously weak front inner structure of the 67-70 Cougar / Mustang. All three of these easy to install upgrades are outlined in the BOSS 302 Chassis Modification book that is NOT included in this package. After you install this kit you will wonder how you could have possibly lived this long without it. Even if you already have the one piece export brace, the chances are it is the old ill fitting off-shore...

Must have for 69-70 convertible owners or anyone else who wishes to tighten up the notoriously weak front inner structure of the 67-70 Cougar / Mustang. All three of these easy to install upgrades are outlined in the BOSS 302 Chassis Modification book that is NOT included in this package. After you install this kit you will wonder how you could have possibly lived this long without it. Even if you already have the one piece export brace, the chances are it is the old ill fitting off-shore...

This harness connects the convertible top switch to the pump on both the xr7 and standard 1969 - 1973 convertibles.

This short harness attaches to the black power wire coming from the starter solenoid and then attaches to the harness that brings the power back to the convertible top pump or power sunroof motor. This harness is for the 1969 XR7 or 1969 Standard and the 1970 Standard but it is not correct for the 1970 XR7 with power sunroof or convertible top as the 1970 XR7 used a rocker switch mounted in the dash pad located above the AC or AC block off plate. *NOTE* Side by side comparisons between 1969...

This listing is for a TEMPLATE which would be used to cut your own shock tower weld in plates. Our supplier made a batch of weld in plates to the wrong thickness, so we're selling this template for anyone who has the ability to fabricate their own. As a stand alone item, this template will not work for what it's indented for because it's too thin. It's made from 18 gauge steel (the actual plates are supposed to be 11 gauge) so they're worth nothing more than being a pattern for the...

Ready to clean up and install, not bent, tight joints, minimal surface rust.

Ready to clean up and install, not bent, tight joints, minimal surface rust.

Passenger side convertible frame assembly mounting and pivot bracket for all 1969-70 Mercury Cougar and Ford Mustang. Does not include the hydraulic cylinder bracket, cylinder mounting bracket sold separately. Bushings, bolts, and specialty fasteners not included. Passenger side bracket with attached convertible arm only. Mounts behind the quarter interior panel. Ford part number C9ZZ-7653118-A.

Driver side convertible frame assembly mounting and pivot bracket for all 1969-70 Mercury Cougar and Ford Mustang. Does not include the hydraulic cylinder bracket, cylinder mounting bracket sold separately. Bushings, bolts, and specialty fasteners not included. Passenger side bracket with attached convertible arm only. Mounts behind the quarter interior panel. Ford part number C9ZZ-7653119-A.

Preproduction wiring harness, connects the convertible top switch to the pump on both the xr7 and standard model Cougars and Mustang 1969 - 1973 convertibles.

Grade B used convertible sun visor bracket assembly for the driver side of any 1969-70 Mercury Cougar or Ford Mustang. Grade B will have some pitting in the pot metal. Sanding and painting will be required for the best results.  These will almost always, show some wear in the pocket, where the hook attaches.Ford casting number C9ZB-7604123.

Grade B used convertible sun visor bracket assembly for the passenger side of any 1969-70 Mercury Cougar or Ford Mustang. Grade B will have some pitting in the pot metal. Sanding and painting will be required for the best results.  These will almost always, show some wear in the pocket, where the hook attaches.Ford casting number C9ZB-7604122.

Used passenger side convertible latch handle. Fits 1969-70 Mercury Cougar and 1965-70 Ford Mustang. Cast aluminum, good condition, may have a nick or scratch, fully functional and does have the bushing for the attaching bolt. Will need a new hook if desired. Ford part number C4ZB-7650534-C.

Used driver side convertible latch handle. Fits 1969-70 Mercury Cougar and 1965-70 Ford Mustang. Cast aluminum, good condition, may have a nick or scratch, fully functional and does have the bushing for the attaching bolt. Will need a new hook if desired.  Ford part number C4ZB-7650535-C.

Used convertible top switch for all 1969 Mercury Cougar standard and XR7, 1970 standard Cougar (76A), all 1969-70 Ford Mustang. This switch is located over the radio bezel. Used and tested convertible top switch, it will not come with a knob. This switch was also used on Cougars with factory power sunroofs. *Note - The 1970 Mercury Cougar XR7 had the power top switch located in the convenience switch panel in the dash.

Our 1969 grade "A" rear quarter panel extensions have no obvious dings, scrapes, or warping due to over tightening of studs. However, avoiding the bumper contact dents is impossible. These will have small dents from bumper contact. There are very slight differences between 1969 and 1970 and they do carry different part numbers. Ford part # C9WB-6528518, Mercury MPC # C9WY-6528010-A. Do you have questions about your Cat's factory pinstriping? This link may help. ...

Our grade "A" fender extensions have no obvious dings, scrapes or warping due to over tightening of studs. Ford part # C9WB-16A169-B, Mercury MPC # C9WY-16019-A. Do you have questions about your Cat’s factory pinstriping? This link may help.