All Available Parts - 1969 Mercury Cougar

This A/C tag clip fastens the aluminum tag to top of the A/C pump.

Reproduction Accelerator Pedal for the 1969 and 1970 Mercury Cougar

Black moulded plastic pedal pad for all 1969 and 1970 Mercury Cougars regardless of engine or transmissions. Used pads with various amounts of wear on the surface. Stainless surround trim available too - Part number C9OZ-9735-A.

York compressor for air conditioning systems for Mercury Cougar and Ford Mustang. These should be professionally inspected or rebuilt and our compressors have all been in storage for some time. Shipped without pulleys, clutches, or valves. The York compressor is constructed mostly of aluminum and is lighter than the Tecumseh brand compressor by 10 pounds. The York compressors are less common too, subject to availability. We often see part numbers on the York tag (which does not list a Ford...

Tecumseh compressor for air conditioning systems for Mercury Cougars and Ford Mustangs. These should be professionally inspected or rebuilt and our compressors have all been in storage for some time. These Tecumseh compressors came with a front oil fill plug up until 1967, thereafter, they have a top fill plug. Top fill is the most common, and likely what you will receive, unless you specify the 1967 style with front fill. These units are shipped without pulleys, clutches, or valves. The...

For 1969 Mercury Cougars and Ford Mustangs with the 351W engine and also for 1970 Cougars and Mustangs with the 351W or 428CJ engine. This is a Pitts manufactured pulley and clutch assembly with a pulley diameter of 6-5/16", a clutch diameter of 5-3/16", and an overall thickness of 1-1/2 inches. Ford part # C9AA-2981-D1. May also have part # C9AA-2981-D2.

For 1969-70 Mercury Cougars and Ford Mustangs with the 351W engine. This is an Eaton manufactured pulley and clutch assembly with a pulley diameter of 6-5/16", a clutch diameter of 6", and an overall thickness of 2-1/16 inches. Ford part # C9AA-2981-F.

Core used set of Eaton clutch brushes, we save these because of the FoMoCo stamped bracket with Ford part number C7AA-2979-A. It is possible to reuse the FoMoCo stamped bracket from the originals and re-rivet to reproduction version. Yes, you can make it sneaky concours. You would have to figure out the rivets though. See related items for NEW Eaton brushes. Pitts compressor clutch is the most common one starting in 1969. Replaces Ford part #: C5ZZ-2979. C7AA-2979-A ...

This reproduction OEM steel power disc brake line kit for Mercury Cougar is bent and dropshipped from the supplier when it is ordered. These kits include all of the steel lines that run from the master cylinder to the wheel cylinders. It does not include the flex tubes. Originally optional only on R code, GT-E, Cobra Jet, and Boss Eliminator.

This reproduction stainless steel power disc brake line kit for Mercury Cougars and Ford Mustangs equipped with the 9 inch rearend and 31 spline axles is bent and dropshipped from the supplier when it is ordered. These kits include all of the steel lines that run from the master cylinder to the wheel cylinders, but it does not include the flex tubes that connect to the caliper. Only an option on R codes, GTEs, Cobra Jets and Boss Eliminators.

This reproduction OE steel standard drum brake line kit for Mercury Cougars equipped with the 9 inch rearend with 31 spline axles is bent and dropshipped from the supplier when it is ordered and is available in OE steel or stainless. These kits include all of the steel lines that run from the master cylinder to the wheel cylinders, but it does not include the flex tubes that connect to the calipers.

This reproduction stainless steel standard drum brake line kit for Mercury Cougars and Ford Mustangs equipped with the 9 inch rearend and 31 spline axles is bent and dropshipped from the supplier when it is ordered. It is available in OE steel or stainless. These kits include all of the steel lines that run from the master cylinder to the wheel cylinders, but it does not include the flex tubes that connect to the caliper.

This reproduction steel power drum brake line kit for Mercury Cougars equipped with the 9 inch rearend and 31 spline axles is bent and dropshipped from the supplier when it is ordered and is available in OE steel or stainless. These kits include all of the steel lines that run from the master cylinder to the wheel cylinders, but it does not include the flex tubes the connect to the caliper.

This reproduction stainless steel power drum brake line kit is for Mercury Cougars and Ford Mustangs equipped with the 9 inch rearend and 31 spline axles. It is bent and dropshipped from the supplier when it is ordered and is available in OE steel or stainless. These kits include all of the steel lines that run from the master cylinder to the wheel cylinders, but it does not include the flex tubes that connect to the caliper.

This reproduction steel power disc brake line kit for Mercury Cougars equipped with the 9 inch rear end with 28 spline axles is bent and dropshipped from the supplier when it is ordered. These kits include all of the steel lines that run from the master cylinder to the wheel cylinders, but it does not include the flex tubes that connects to the calipers.

This reproduction stainless steel power disc brake line kit is for the Mercury Cougar equipped with the 9 inch rear end and 28 spline axles. It is item is bent and dropshipped from the supplier when it is ordered. These kits include all of the steel lines that run from the master cylinder to the wheel cylinders, but it does not include the flex tubes that connect to the calipers.

This reproduction steel power drum brake line kit for Mercury Cougars equipped with the 9 inch rear end with 28 spline axles is bent and dropshipped from the supplier when it is ordered and is available in OE steel or stainless. These kits include all of the steel lines that run from the master cylinder to the wheel cylinders, but it does not include the flex tubes that connects to the calipers.

This reproduction stainless steel power drum brake line kit for Mercury Cougars and Ford Mustangs equipped with the 9 inch rear end and 28 spline axles is bent and dropshipped from the supplier when it is ordered. It is available in OE steel or stainless. These kits include all of the steel lines that run from the master cylinder to the wheel cylinders, but it does not include the flex tubes that connect to the caliper.

This reproduction OE steel brake line kit for Mercury Cougars equipped with the 9 inch rear end with 28 spline axles and is bent and dropshipped from the supplier when it is ordered and is available in OE steel or stainless. These kits include all of the steel lines that run from the master cylinder to the wheel cylinders, but it does not include the flex tubes that connect to the caliper.

This reproduction stainless steel standard drum brake line kit for Mercury Cougars and Ford Mustangs equipped with the 9 inch rear end and 28 spline axles is bent and dropshipped from the supplier when it is ordered. It is available in OE steel or stainless. These kits include all of the steel lines that run from the master cylinder to the wheel cylinders, but it does not include the flex tubes that connect to the caliper.

[No Description Provided]

Replace those rusty, failing brake lines with these Reproduction Stainless Steel Front Power Brake Drum 5 Line Set for the 1967, 1968 and 1969 Mercury Cougar

Also Correct for some 1967 models with proportioning valve at front

Also correct for some 1967 models with proportioning valve at front

Brake line rubber grommets for any 1967-73 Mercury Cougar or Ford Mustang. These are the ones that go through the shock towers for the front brake lines. Drum or disc, all the same. Sold as a PAIR. Ford number 373624-S.

We will make sure these original seat belt bolts are damage free and rust free. There were minor and major changes almost every year. We also have hundreds of used belts and belt sets that we cannot possibly list all of, so give us a shout for details! 503-463-1130*NOTE* Pictured is a complete set of 1969 Torx bolts, spacers and washers for a coupe.

We will make sure these original seat belt bolts are damage free. There were minor and major changes almost every year. We also have hundreds of used belts and belt sets that we cannot possibly list all of, so give us a shout for details! *NOTE* Pictured is a complete set of 1969 Torx bolts, spacers, and washers for a coupe. May also have some minimal surface rust.

Replaces Ford Part # C7SZ-3D600-A. Power steering pump adjusting spacer for use without air conditioning. For most 1967 - 1969 Mercury Cougar or Ford Mustang with 289, 302, 390, 428CJ engines, excludes 1969 351W and 1969 Boss 302 engines. Spacer dimensions: 7/16" I.D. x 1" O.D. and 9/16" thick.

Unique for the 1969 351 Windsor engines without air conditioning. Flat steel bar stock spacer that positions the power steering pump a measured distance away from the cylinder head. The bars are 3-3/8" x 3/4" x 1/2" in size. The threaded hole in the center is tapped 3/8-16. The two outer holes for attaching to the cylinder head are 11/33" holes on a 2-9/16 inch center. Verify the pre-tapped holes in your cylinder head if making your own spacer. For 1970, a round spacer was used, as could be...

Used convertible rear seat structure cut from a 69 - 70 Cougar Convertible parts car. This will not fit a Mustang due to the differences in the wheel houses and transition panel. Keep in mind that this is an oversized item and cannot ship through any conventional means. Truck freight and crating fees will apply. 

Reproduction driver side inner rocker panel for the 69 - 70 Cougar Convertible

Reproduction passenger side inner rocker panel for the 69 - 70 Cougar Convertible

This "Stick On" Cougar rear deck emblem was only used on models without the XR7 package. They are often missing as once the factory double sided tape dries out they are often lost forever. We also have a few very nice used examples in stock.We often get asked about where to place 69-70 XR7 and Cougar adhesive emblems. Based on personal experience and pictures from the original Ford archives the answer would be "Pretty much wherever you think looks best". Often as seen in this picture the line...

Good used emblem with both studs intact, no obvious pitting or scratches. This item will have a faded center decal, and you will need a new decal. You can either add a note to the order asking that we contact you about upgrading to an emblem with less fade for a upcharge, or get a reproduction decal here. Ford casting number reads C9WB-8B369-A ...

Nice reproduction that is "almost" spot on. Of the two versions available this one has much more definition. When you put an original next to this reproduction you will notice the original has a more raised, defined face on the Mercury Man.

This is a used coral with a new background decal and walking cat emblem. We ship the three parts unassembled so you can re-chrome the corral if you desire. The corral will not be perfect but it will not be heavily pitted either. You can expect the part you receive to resemble the one pictured here.Casting number: C9WB-18B000

Good used pit free emblem. We now have the black background decal in reproduction form. Casing number: C9WB-18B000 Do you want to replace those worn out actuators yourself or are you looking for some great information on aligning the grille in your Cat? The videos below are your ticket! Check out this video ...

Unique for the 1969 351 Windsor engines without air conditioning. Flat steel bar stock spacer that positions the power steering pump a measured distance away from the cylinder head. The bars are 3-3/8" x 3/4" x 1/2" in size. The threaded hole in the center is tapped 3/8-16. The two outer holes for attaching to the cylinder head are 11/33" holes on a 2-9/16 inch center. Verify the pre-tapped holes in your cylinder head if making your own spacer. For 1970, a round spacer was used, as could be...

Very rarely do we find one like this example that shows no sign of fading. This is for the person who is trying to achieve a very high level of preservation / restoration.

Good used center with no cracks and an average amount of fade most noticeable in the red portion of the emblem. Many of these emblems are broken or missing because people think this is the horn button and if they just push harder the horn will sound!

Good used pit free emblem that would be good for restoration. Notice the clips are in place and there are no cracks in the plastic backing. The example picture of the installed emblem is what they looked like when restored. These mount on the lower part of the roof behind the quarter windows. This part of the roof is also known as the 'C' pillar.

Used front fender extension "Cougar" script. The one you receive may not look as good as the one pictured but will be very close in condition, expect one of the four studs on the back to be missing. Ford Engineering number as found on the backside: C9WB-16098-B Ford number C9WB-16098-A. Note that the 1970 version stamped D0WA-16098-A is slightly different, most noticeable on the letter "C".

Correct anodized aluminum reproduction emblem for 1969-70 quarter panels. These high quality emblems have the black paint applied to the sides just as the originals did. If you want an emblem that better matches your front Cougar script you might want to consider these chrome emblems. You can reference the above pictures for correct dimensions, as taken from one of our cars using an original script emblem. Measurements are from the rear and lower body lines. *NOTE* This item includes the three...

Used COUGAR Script Quarter Panel Emblem for the 1969 and 1970 Mercury Cougar

High quality reproduction adhesive emblem for your deck lid. Measures 6.5" wide by 2.35" tall. It has the correct black paint applied to the sides. If you have a 71-73 Cougar this chrome emblem is a much better match to your other emblems even though it is not technically correct. We often get asked about where to place 69-70 XR7 and Cougar adhesive emblems. Based on personal experience and pictures from the original Ford archives the answer would be "Pretty much wherever you think...

Good used emblem with no bends, but will be scratched. Will need new adhesive tape as these did not come with studs. For any Cougar, but only came on 1969-70 Standard Models, and all 1971-73 Mercury Cougars. 1971-73 XR7 and Standard Models, as well as convertible.We often get asked about where to place 69-70 XR7 and Cougar adhesive emblems. Based on personal experience and pictures from the original Ford archives the answer would be "Pretty much wherever you think looks best". Often as seen in...

Good used condition, hard to find with perfect chrome. Often times there will be some shrinkage in the rubber.  We cannot guarantee that we will always have the more obscure colors in stock like aqua. We seldom have black in stock. FYI

This vinyl piece glues to the center of your block off plated on Cougars not equipped with AC. These often times have shrunk slightly over time. We cannot guarantee to always have all the colors in stock. Call for color availability or put desired color into the comments section of your order.

This small sized Cougar emblem (1 3/8" long) was used on 1969 - 1973 Cougars without AC. It was affixed to a block off plate in the very venter of the dash by two peened over die cast studs. It will glue back in place nicely and many Cougar fans have found fun "custom" applications for this attractive piece. This emblem will not be pitted or scratched in any way.

Grade "A" pit free original metal emblem for your Eliminator or Standard model Cougar. If you look closely at our picture you will in fact see tiny imperfections in the chrome. We rarely ever get flawless examples of this particular emblem as the original plating was substandard (in our opinion). This emblem was used on the standard, decor and Eliminator models.

Located on the right hand dash panel of your XR7, requires drilling to remove properly.

Adhesive backed, located on the right side of your deck lid.  We often get asked about where to place 69-70 XR7 and Cougar adhesive emblems. Based on personal experience and pictures from the original Ford archives the answer would be "Pretty much wherever you think looks best". Often, as you can see one of our example photos above, the line workers did not even attempt to get them very well centered. Both emblems were placed on the RH side of the deck lid "somewhat" centered top to...

This Super Cobra Jet emblem was never used on a Cougar, but is the Cobra Jet emblem used on the Hood Scoop for 1969-1970 Mustangs. It is also an attractive emblem for your custom application. Thanks for the plug Mark!: "My first deal with Don was clear back in the 1980s and I have sent a few people his way and all came away happy. While at his shop on Monday I watched Lin crawl under a convertible, phone in one hand and a tape measure in the other, and measure a cross...

Good used fuel door framed insert, without the crest as shown. These in most cases will not include the thin foil backing plate as shown. "A" grade will have minor rust pitting and some dullness on the chrome, overall very good used.Foil backing plate available in reproduction, see related items.

Fair used fuel door framed insert, without the crest. These most often will not include the thin foil backing plate as shown. "B" grade will have some rust pitting and some dullness on the bright work, overall fair used. Foil inserts available used in limited quantities.

These are sold individually, two required per car. This is the aluminum emblem / decal which mounts on the center of some late 67 and all 68-73 scuff plates. Features raised script like original. Adhesive backed with a protective coating that peels off after installation. Replaces Ford Part #: C7ZZ-6513208-T. Licensed by FORD ...

No... Mercury never made an emblem "just" like this one but demand dictated we produce it! This emblem has a 3M adhesive backing and looks and measures just like a 1968 quarter panel script or the front fender script found on a 1971 - 1973. Many people do not like the looks (or price) of the 67 quarter panel emblems so this is a great alternative that does not require you drill holes. The 3M backing is the same found on modern automotive emblems so it will not fall off. Just like our other...

Since our restored emblems look so good we have a hard time selling NOS these days which works out just fine as we only seem to be able to obtain 1 of these every few years. Keep in mind your used cores have trade in value against this NOS part. Casting number seen on back side for the assembly is C9WB-65517A56-A and black plastic is C9WB-65517C00-A, Casting number on chrome is C9WB-65517A20-A

New adhesive backed foil insert that goes behind the walking cat on the passenger side headlight eyelid door on the 1969 Mercury Cougar.  You will likely want to purchase the reproduction walking cat when replacing this foil insert. You will have to break the original studs to remove the cat to replace the foil. The reproduction walking cat comes with two flat attaching clips. We also offer a restored emblem corral (chrome surround) for the walking cat. You...

This is the correct size walking cat decal for your eyelid door on the 1967 - 1969 Cougar. It has the studs in the exact place as the originals. You will need this emblem when changing out our 1967 - 1969 background decals as you will have to break the original studs to remove the cat. Also great for those custom applications! Emblem is approx 3 3/4" wide by 1 1/4" tall. This cat does come with two flat attaching clips. *Customer Feedback* Hey Don and Lin, Just wanted to send a couple pictures...

Good used plastic emblem with no peeling chrome. This was used on all models except XR7 on the right side. We also have the metal version of this emblem available.

Reproduction center emblem for the 69 Cougar rim blow steering wheel.

Good used center with minor cracking, missing paint or maybe even a broken mounting tab. This was used on all 1969 Cougars with a three spoke wheel except the XR7.

Grade A used, trunk emblems for 1969-70 XR7 models. We will very seldom have this in stock, the alternatives are grade B used or reproduction. Please see related items below. We often get asked about where to place 69-70 XR7 and Cougar adhesive emblems. Based on personal experience and pictures from the original Ford archives the answer would be "Pretty much wherever you think looks best". Often as seen in this picture the line workers did not even attempt to get them very well centered. Both...

Restored emblem / insert for the 69 Cougar center grille. These are sold on an exchange basis, so you must have a good core with both studs intact. The emblem will be without the decal in the center. You can get it here. Ford casting number reads C9WB-8B369-A NOTE! If you pay the core charge on our 1969 restored grille parts or complete grilles we will be under the assumption you do not have cores to send in or they are average quality with pits and cracks. If you have really clean cores you...

Reproduction ribbed aluminum foil backing plate for the gas doors on the 1969 and 1970 Mercury Cougar and XR7 models.

Restored corral for the passenger side eyelid on the 1969 Mercury Cougar. This is just the outer corral and does not include the background decal or the walking cat emblem. NOTE! If you pay the core charge on our 1969 restored grille parts or complete grilles we will be under the assumption you do not have cores to send in or they are average quality with pits and cracks. If you have really clean cores you will want to send them in advance and not pay the core charge so we can do what we call...

Decent reproduction of the 69-70 Cougar fender extension COUGAR script. This emblem was used for 2 years only and was located on the driver side front fender extension (fender cap). The originals came with speed nuts but these have push on clips from the back which means they are easier to install as no tools are needed. If one looks very close you will see minor differences compared to original examples. If you want to trade in your dull, pit free emblem for store credit we will give $20 for...

Grade "B" original metal emblem for your Eliminator or Standard model Cougar. Grade B emblems will have pitting and faded or missing paint. We rarely ever get flawless examples of this particular emblem as the original plating was substandard (in our opinion). This emblem was used on the standard, decor and Eliminator models.

Restored fuel door framed insert without the background decal or crest, for the 1969 - 1970 Mercury Cougar. Foil backing plate available in reproduction. At the moment there are no reproductions on the walking cat, you can however polish up your old cat and re-use it in this frame.

Often when your door will not latch this is the culprit.

Convenient matched sets save costly locksmith work. Kits includes a pair of door lock cylinders. Comes with two keys. Includes door cylinder gaskets. If you don't mind have having a different key for the door locks, this product might just work out.Attention potential buyer! This item will likely give you problems and be a general disappointment. Reviews show that the fitment is fair, and you will not be able to have these lock cylinders re-pinned, to use your original Ford key. One...

Finally an affordable reproduction is available. Steel stamped complete door latch assembly that goes inside your passenger side door and catches on the door striker assembly. See hardware for clips. Replaces Ford Part # : C9AZ-6221812-A

Includes two door lock cylinders, two door cylinder gaskets, two keys and one ignition lock cylinder.  Made by the original OEM supplier.  That being said, they do not make them like they used to. Replaces Ford part # C7AZ-6222050-A or C9AZ-6222050-A.

Includes three cylinder clips, two door cylinders, two door cylinder gaskets, two keys, one trunk cylinder, one trunk cylinder gasket, and one ignition cylinder. Made by the original OEM supplier. Makes 1 key fit all our locks! Replaces Ford part #: C9AZ-6222050-A

Steel door latch reinforcement repair kit. Countersunk bushings and screws for reinforcing the inside the door mounted latches on 1967-70 Mercury Cougar and Ford Mustangs. Kit has 6 machine screws and bushings, enough for both doors. The metal on the doors is very prone to cracking in the screw area for those latches.

Reproduction polished stainless steel door strikers for your Mercury Cougar or Ford Mustang. This kit includes stainless steel hardware and will make your door jambs pop.Replaces Ford part # C5AZ-6222008-A.

Used passenger side (right hand) complete door latch assembly for the Mercury Cougar XR7 or Ford Mustang with door ajar option. This unit goes inside your door and catches on the door striker assembly on the door jamb. Tested and inspected, this latch does the have the provision for the door ajar switch as found on all XR7 models. Door ajar switch sold separtely. This will fit all years 1967-70, was used as a service replacement. Just has a shorter tab for the key lock rod. Must use...

Used driver side (left hand) complete door latch assembly for the Mercury Cougar XR7 or Ford Mustang with door ajar option. This unit goes inside your door and catches on the door striker assembly on the door jamb. Tested and inspected for excessive wear. This latch does have the ability to mount the door ajar switch, as found on all XR7 models. Door ajar switch sold separately. Must use the 1969-70 door ajar switch with this mechanism. Ford part # C9AZ-6221813-A. ...

These are the screws that secure the door latch mechanism to the door shell. These screws come with the attached crown headed lock washer, just like the originals, so be sure to tighten them down snugly to ensure that the screw head sits flush into the screw holes. Sold individually. Three required per door, six per car.

Door lock latch lever, for driver or passenger side locks. Attach with an "E" clip on the rear side of the lock mechanism. Used "E" clip is included. We are going to say that these fit all Ford door locks 1965 through 1973 and beyond. *Note you will need to purchase or reuse your retainer clip for attaching the lock rod. Retainer clip not included, we have good used or reproduction clips, see related items.Ford number stamped C5AB-6221970-A or D2AB-6221970-AA  ...

1969-70 Mercury Cougar and Ford Mustang latch rod that links the door latch and the inside door handle, right or left side door. Normally this rod was fabric covered. Used rod only, no retaining end clips.Replaces Ford part number C9ZZ-6521940-B.

Used interior door release mechanism. Other Ford names include: door remote, control, linkage assy, latch assembly. The spring is the weak link on these parts. Passenger and driver side are different, this is for the passenger side only, comes with attaching parts as shown. Replaces Ford part number C9AB-6221818-A.

Used interior door release mechanism. Other Ford names include: door remote, control, linkage assy, latch assembly. The spring is the weak link on these parts. Passenger and driver side are different, this is for the driver side only, comes with attaching parts as shown. Replaces Ford part number C9AB-6221819-A.

Plastic insert with metal locking retainer. The plastic came in various colors, white, red, and black are common. Replaces Ford part # C5AZ-6221952-A.Check out our handy diagram below to find other '67-'68 door parts you may need. All the item numbers shown can be typed in to the search bar on our site. (Click image to view full size) ...

Reproduction rubber bumper for your 67 - 73 Cougar or Mustang door latch mechanism. The bumper sits on the inside of your door latch mechanism, and is there to dampen the blow from the striker when you close your door.

When ordering this item, you do not need to order a key blank, the key is included. If you need more than one key, you don't need to pay for multiple key cutting services, just buy extra blanks and mention it in the comment section of your order. This listing is for the ECONOMY version of the trunk / glove box key. We now have the ability and equipment from an old Lincoln Mercury dealership to cut keys for Fords "by the numbers". Instead of copying a worn key to make yet another key that...

Refurbished pair of door lock cylinders and ignition cylinder for all double cut key Fords 1967-69. These are coded to the original key code, which was stamped onto one of the door lock cylinders. Includes two door lock cylinders, two Ford keys, and one ignition lock cylinder. Assembled from the best used locks. Replaces Ford part # C7AZ-6222050-A or C9AZ-6222050-A.

When ordering this item, you do not need to order a key blank, the key is included. If you need more than one key, you don't need to pay for multiple key cutting services, just buy extra blanks and mention it in the comment section of your order. We now have the ability and equipment from an old Lincoln Mercury dealership to cut keys for Fords "by the numbers". Instead of copying a worn key to make yet another key that doesn't fit properly, we can cut keys as they would have come from the...

You may consider buying our grade "B" door over our grade "A" door if you are doing a high end restoration. Here is the reasoning; due to the design of the 69-70 door, silt is trapped in all of the door corners, these tight recesses always have silt collected in them and when you add moisture you get corrosion. Our grade "A" doors do not have noticeable blisters but since there is no paint or sound deadener in the depths of the corners we know there is some amount of corrosion taking place...

Concours? almost, these are stainless steel screws with the wax tipped coating like the originals, for installing the door sill plates. The wax was deemed necessary by the Ford Motor Co. as a seal. These can be used on all years 1967-73 Mercury Cougar, Ford Mustang and most all other Ford, Mercury, Lincoln cars of the era. Works well with any of the reproduction sill plates, these were really made to be used with the premium reproduction sill plates in stainless steel. 1967-68 Cougar and...

These are the same left to right, convertible or coupe. These appear to be made from the same thickness of aluminum as original and weigh .44 pounds as opposed to .50 for the originals but the aluminum used is not nearly the quality of originals. You can literally mutilate these parts with your fingers as you would an aluminum can. We recommend the premium quality sills. These are a poor reproduction that will not hold up well over time, we cannot recommend this part. We HIGHLY recommend...

Worn, scratched, dull but usable. Will have dents from seat belts.

Ford never made these in stainless but what a great upgrade! The advantage we see with these is that they do not dent or scratch as easy when you release your seat belt. They also can be polished easily (unlike anodized aluminum). These weigh 1.5 pounds each, triple of what the originals weigh. Sold as a pair only. *NOTE* Since these are stainless they look great next to our "accessory" stainless steel sill plates we offer. The secondary "accessory" strips cover the painted portion of the door...

These weigh .50 pounds each, exactly as the originals do. Just like the originals, these are very prone to scratches and dents, even letting your seat belt fall will mark them up. Although these sill plates are better than our economy version, we still rate them below OEM which was also prone to damaging easily.  We HIGHLY recommend the stainless version we sell. These are sold individually, coupe, convertible, left and right are all the same. Decals are sold...

Concours? almost, these are stainless steel screws with the wax tipped coating like the originals, for installing the door sill plates. The wax was deemed necessary by the Ford Motor Co. as a seal. These can be used on all years 1967-73 Mercury Cougar, Ford Mustang and most all other Ford, Mercury, Lincoln cars of the era. Works well with any of the reproduction sill plates, these were really made to be used with the premium reproduction sill plates in stainless steel. 1967-68 Cougar and...

Sold as a Kit as Pictured.

One size fits all.  Set of 4.  Good replacement if not worried about show quality. 1967 – 1968 Coupe 6 Required per car 1969 – 1973 Coupe 4 required per car 1969 – 1973 Convertible 2 required per car Will also work on the 69 - 73 shifter bezels. 4 required. Not recommended for our Mass Backed Carpeting. Please see related items for the longer screws. Replaces Ford Part #: 381571-S