1973 Ford Mustang

Used air conditioning connecting duct or manifold. This plastic manifold mounts behind the center dash vent. Ford calls it a 'duct and connecting assembly' or 'A/C junction'. Grade 'A' condition, ships without cracks, splits, or broken tabs. Original factory or 'integral' air conditioning part.Ford part number D1ZZ-19C932-A.

Reproduction A/C evaporator for your Mercury Cougar or Ford Mustang.*Note - We have had numerous customers complain that these don't fit exactly like the originals.As far as evaporators go, we highly suggest going with a good used evaporator over these new versions. What happens is this: These companies use more coils (35% more passes) which equals out to thinner metal, which also equals out to performance that's sub-par to a good used original evaporator.Click on images to enlarge. ...

Used air conditioning evaporator core for 1971-73. We only sell used coils that are clean and sealed and do not sell coils that have pest damage or have corrosion from a leaking heater core. Even though we stand behind these used units for 30 days, we still suggest that you pressure test them before installing as we all know what kind of labor is required to install one of these. 1971-73 evaporators have 2 male fillings, and the whole unit is made of aluminum, including the tubes.Ford part #...

Exact replacement to original drier that removes moisture and should be changed anytime system is recharged. It really is the life of your system. This stainless steel filter element stops contaminants from clogging the expansion valve.

High quality and correct looking air conditioning discharge hose for Mercury Cougars or Ford Mustangs. This hose is compatible with both 134a and R12 refrigerants.

Regardless of which V-8 engine, D1ZA-19972-AA or D1ZA-19972-AB part number. This hose is approximately 24 inches long. These used hoses probably still hold pressure, we suggest a purchase of new 'O' rings prior to installation.

For Mercury Cougar and Ford Mustangs with integral or factory installed air conditioning with any V-8 engine. Original condensation drain hose from the A/C case, through the floor board, to the ground. Correct "S" shaped moulded hose with restrictor intact. Almost the same hose as was used 1969-70, Dearborn assembly line hoses have a ribbed section 1971-73. The 1969-70 versions, typically have the alligator texture on the outside of the hose.  Ford part # C9ZZ-19858. ...

Regardless of which V-8 engine, D1ZA-19867-BC part number. This hose is approximately 49 inches long.

This is actually a kit which includes 2 hoses (Part # D1ZA-19835-A and Part # D1ZA-19837-A), the sight glass (Part # SG3, D2AZ-19D695-BK or YF-342), 2 o-rings (Part # L33,D2AZ-19D695-R or YF-368 and Part # H33, D2AZ-19D695-AE or YF-316) and a quick connect (Part # QF3,C1SZ-19B696-A or YF-241 and Part # QM6, C1SZ-19B695-A or YF-252). *Note we normally supply the new coupler with this kit. Regardless of which V-8 engine, this hose when assembled is approximately 78 inches long.Ford MPC kit #...

For 1972-73 Mercury Cougars and Ford Mustangs with the 351W engine. This is a Pitts manufactured pulley and clutch assembly with a pulley diameter of 6-5/16", a clutch diameter of 5-1/8", and an overall thickness of 1-11/16 inches. Whew boy, say that 5 times fast!Ford part # D2ZA-2981-A. May also have part numbers of D2ZA-2981-A1A, D2ZA-2981-A1B, or D2ZA-2981-A2A.

This A/C vacuum canister mounts to the passenger side shock tower and controls damper doors inside the A/C unit. This unit includes a built in check valve. Used and tested vacuum tank and bracket, also known as the A/C vacuum reservoir. Fits all 1971-73 Mercury Cougar, 1971-73 Ford Mustang, as well as 1970-71 Ford Torino / Fairlane and Mercury Cyclone Montego, 1970-7? Ford Maverick and Mercury Comet.Replaces Ford part # D0DZ-19A566-A.  

part # 370608-S. Used in multiple places on mounting brackets.