All Available Parts - 1973 Ford Mustang
Products (Click sub-categories above to ONLY display results for that Sub-Category) 1801-1900 of 2233
Sorted By:
Availability:
Display Options:
Availability: Out of Stock
Item #: 11-0293 -
Used push in retainer for any 1967-73 Mercury Cougar or Ford Mustang. These fasteners are used to attach the floor vent / duct to the blower housing, and to connect the defroster assembly to the blower housing, etc. Sold individually.Replaces Ford part number 380464-S.
Availability: Used / Wrecking Yard Item
Item #: 11-0431 -
Lower heater duct to floor outlet for Cougars and Mustangs with air conditioning. Used grade "A" part and may have one very minor defect. This part will be damage free. Fits 1971-73 Mercury Cougar and Ford Mustang with factory air conditioning. Replaces Ford part number D1ZZ-18C366-A.
Availability: Used / Wrecking Yard Item
Item #: 11-0433 -
Lower heater duct to floor outlet for Cougars and Mustangs with air conditioning. Used grade "B" part and will have one defect. This part will have a crack, chip missing, etc. Fits 1971-73 Mercury Cougar and Ford Mustang with factory air conditioning. Replaces Ford part number D1ZZ-18C366-A.
Availability: Used / Wrecking Yard Item
Item #: 11-0435 -
Used vacuum actuator for controlling the center A/C vent on any 1971-73 Mercury Cougar or Ford Mustang. This is a bare vacuum valve, that does not have the screwed on extension which make the unique part numbers from the Ford MPC. Tested and holds vacuum. This is the unique valve with two separate vacuum ports. 2 ports for two different positions. Ford part number D1ZZ-18A318-A.
Availability: In-Stock Item
Item #: 31283 -
New push in retainer for any 1967-73 Mercury Cougar or Ford Mustang. These fasteners are used to attach the floor vent / duct to the blower housing, and to connect the defroster assembly to the blower housing, etc. Sold individually. These are all plastic with flush mounted head. Replaces Ford part number 380464-S.
Availability: Used / Wrecking Yard Item
Item #: 11-0455 -
Black plastic air conditioning center vent register bezel for any 1971-73 Mercury Cougar or Ford Mustang with Factory installed or integral A/C. Mounts Horizontally in the dash panel. Individual vents roll 360 degrees to blow air straight or to the sides. For that extra level of detail, we suggest using a silver paint pen for detailing the silver edges. Ford part number D1ZZ-19893-A.
Availability: Used / Wrecking Yard Item
Item #: 11-0468 -
Windshield defroster nozzle for Mercury Cougar and Ford Mustang without A/C. This is a "B" grade unit and will have 1 or 2 minor defects. Defects such as a crack or a single broken tab. Will be an operational unit and is better than not being able to defrost your windshield. You will need to staple the flex part onto your heater unit. Very fragile part, almost always going to have Grade B, seldom will we have a Grade A used.Ford part # D1ZA-18A565-AD
Availability: In-Stock Item
Item #: 14968 -
New internal speedometer gear fits 4 speed toploader transmissions. Replaces Ford Part #: C5ZZ-17285-A.
Availability: In-Stock Item
Item #: 42005 -
Very good quality replacement speedometer cables. 76 inches Replaces Ford Part # : C9ZZ-17260-B
Availability: In-Stock Item
Item #: 12156 -
These four speed gears have the teeth reversed from the direction of the automatic gears. Made from Nylon. These gears only fit the 4 speed Toploaders. Click here to use our Speedometer Gear Calculator. Replaces Ford Part # : C2DZ-17271-G 20 Tooth Gear Pictured
Availability: In-Stock Item
Item #: 15300 -
Clutch Fork Pivot for Cougars manufactured after 2/16/1968. Replaces Ford Part #: C8AZ-7522-A.
Availability: Out of Stock
Item #: 24371 -
C8AZ-7515-B Manual transmission clutch fork - 3 and 4 speed, stick shift transmissions. Fork measures 12-5/16 inches long. Alternate number C8AA-7515-B or C8AA-7541-B. Couple of variations of this fork. Most versions will not be stamped. Spring and side holes not needed for Mustang and Cougar applications. Originally for 1968 full sized cars with 289 or 302 engines and manual transmissions. Maybe 6 cylinders, not sure, but vert likely. Cougar 1971 - 1973, 351 Engines. Mustang 1971 - 1973,...
Availability: In-Stock Item
Item #: 41269 -
Fits 3 speed or 4 speed manual floor shifts. Sold individually. Check out our video on rebuilding your shifter below:
Availability: In-Stock Item
Item #: 14895 -
You will not need to make any modifications to run this leather unit in place of your original rubber boot used on three and four speed manual transmissions.
Availability: In-Stock Item
Item #: 42401 -
Chrome center cap with Red background and chrome Ford logo. Better than original! Original look wheel emblem is made from original dies. This plastic cap is painted and detailed in the original colors. This was never used on any year of Cougar but they do look good! When using center caps on Legendary wheels, you will need these adapter plates. *Note - Certain late model disc brake rotors and aftermarket rotors have a slight clearance issue with the dust cap and these center...
Availability: In-Stock Item
Item #: 32575 -
Reproduction spinner cap for the Magnum 500 Legendary series wheel. Also works with the Magstar II wheel. Each spinner is die-cast with precision and finished in a show quality chrome plating. The exclusive anti-theft retainer plate keeps them in place and secure. A stamped aluminum Magnum 500 emblem and a "Bullseye" emblem are included so owners can choose which one to personalize their car with.Sold individually ...
Availability: Out of Stock
Item #: 30529 -
This plastic center cap comes with each Legendary Wheel we sell at no cost. We list them for those that may lose or break one. The overall width is 2 1/2" and they are designed for a opening that is 2 3/8 " wide. Sold individually.Check out our video on Legendary Wheels below: ...
Availability: In-Stock Item
Item #: 12461 -
Reproduction set of 4 short valve stem assemblies for the Mercury Cougar or Ford Mustang. These new stems will look great on your Magnum, Styled Steel, Shelby, Eliminator or even stamped steel wheel.
Availability: Ships Direct from Supplier (Except International)
Item #: 30459 -
Reproduction 15x7" Eliminator wheel with a black center and chrome rim for the Mercury Cougar or Ford Mustang / Torino. The only version of this wheel Mercury ever used on a factory order for a Mercury Cougar was a painted 14x6 with a trim ring used on the 1969 Eliminator. This black 15x7 is a really great custom made wheel that adds flash without deviating too far from the original look. As always, the cap is sold separate. Click here for the hubcap we recommend for this wheel. If you need a...
Availability: In-Stock Item
Item #: 30524 -
Reproduction 15x7" Eliminator wheel with a charcoal center and chrome rim for the Mercury Cougar or Ford Mustang / Torino. The only version of this wheel Mercury ever used on a factory order for a Mercury Cougar was a painted 14x6 with a trim ring used on the 1969 Eliminator. This charcoal 15x7 is a really great custom made wheel that adds flash without deviating too far from the original look. As always, the cap is sold separate. Click here for the hubcap we recommend for this wheel. If you...
Availability: Ships Direct from Supplier (Except International)
Item #: 30525 -
Reproduction 15x7" Eliminator wheel with a silver center and chrome rim for the Mercury Cougar or Ford Mustang / Torino. The only version of this wheel Mercury ever used on a factory order for a Mercury Cougar was a painted 14x6 with a trim ring used on the 1969 Eliminator. This silver 15x7 is a really great custom made wheel that adds flash without deviating too far from the original look. As always, the cap is sold separate. Click here for the hubcap we recommend for this wheel. If you need...
Availability: Ships Direct from Supplier (Except International)
Item #: 18943 -
These off-shore Magnum wheels are supplied to us by Scott Drake. We no longer carry the US made version as the quality was VERY inconsistent. This wheel has a 4 1/4" backspace. We now have Magnum 500 caps that feature the Mercury Logo and the walking cat caps as well. Center caps and lugs are sold separate.
NOTE! These wheels are intended to be balanced with a lugcentric adapter. They will not balance with a traditional cone spacer on the tire spin balancer. Many tire shops do not deal...
Availability: Ships Direct from Supplier (Except International)
Item #: 18944 -
These off-shore Magnum wheels are supplied to us by Scott Drake. We no longer carry the US made version as the quality was VERY inconsistent. This wheel has a 4 1/4" backspace. We now have Magnum 500 caps that feature the Mercury Logo and the walking cat caps as well. Center caps and lugs are sold separate. These are best suited for 1971-73 Cougars. To run a tire larger than a 225/60/15 you may have to modify your fenders and quarters.
NOTE! These wheels are intended to be...
Availability: In-Stock Item
Item #: 26919 -
New aluminum 15x8" Magnum 500 wheel for your Mercury Cougar or Ford Mustang. A great way to reduce the un-sprung weight on your Cat or Pony and look great while doing it! This item also includes a center cap, but they are a cheap plastic chromed cap with a blacked out center. We recommend using the adapter plates and Magnum 500 center caps we sell from Scott Drake. Lug nuts sold separately, get them here. ...
Availability: Ships Direct from Supplier (Except International)
Item #: 12129 -
New aluminum 17x7" Magnum 500 wheel for your Mercury Cougar or Ford Mustang. A great way to reduce the un-sprung weight on your Cat or Pony and look great while doing it! This item also includes a center cap, but they are a cheap plastic chromed cap with a blacked out center. We recommend using the adapter plates and Magnum 500 center caps we sell from Scott Drake. Lug nuts sold separately, get them here. ...
Availability: Ships Direct from Supplier (Except International)
Item #: 20678 -
New Legendary Series 15x7" Glossy Finish Magnum 500 wheel for your Mercury Cougar or Ford Mustang. While they look almost identical to the original chromed steel version, these are actually a lighter, better-balanced aluminum alloy with a protective coating. These wheels come with free chromed plastic center caps. The caps have a red Legendary logo but we can include at no cost, a set of black and chrome walking cat decals (click here). Just add it to your cart if you'd like these decals. If...
Availability: Ships Direct from Supplier (Except International)
Item #: 20679 -
New Legendary Series 15x7" Satin Finish Magnum 500 wheel for your Mercury Cougar or Ford Mustang. While they look almost identical to the original chromed steel version, these are actually a lighter, better-balanced aluminum alloy with a protective coating. These wheels come with free chromed plastic center caps. The caps have a red Legendary logo but we can include at no cost, a set of black and chrome walking cat decals (click here). Just add it to your cart if you'd like these decals. If...
Availability: Ships Direct from Supplier (Except International)
Item #: 20680 -
ETA FOR THIS ITEM IS 12/14/23Reproduction Scott Drake 16x8" Satin Black Magnum 500 wheel for your Mercury Cougar or Ford Mustang. These are the best quality of the three different Magnum 500 wheels you will find on the market today. The chrome is not only brilliant but it holds up great year after year. You may save a few dollars buying the other brands out there but why? We sell these wheels with a 4 1/2" backspace unless you specify otherwise. We now have Magnum 500 caps that feature the...
Availability: Ships Direct from Supplier (Except International)
Item #: 16246 -
New Legendary Series 15x8" Glossy Finish Magnum 500 wheel for your Mercury Cougar or Ford Mustang. While they look almost identical to the original chromed steel version, these are actually a lighter, better-balanced aluminum alloy with a protective coating. These wheels come with free chromed plastic center caps. The caps have a red Legendary logo but we can include at no cost, a set of black and chrome walking cat decals (click here). Just add it to your cart if you'd like these decals. If...
Availability: Ships Direct from Supplier (Except International)
Item #: 12308 -
New Legendary Series 17x7" Glossy Finish Magnum 500 wheel for your Mercury Cougar or Ford Mustang. While they look almost identical to the original chromed steel version, these are actually a lighter, better-balanced aluminum alloy with a protective coating. These wheels come with free chromed plastic center caps. The caps have a red Legendary logo but we can include at no cost, a set of black and chrome walking cat decals (click here). Just add it to your cart if you'd like these decals. If...
Availability: Ships Direct from Supplier (Except International)
Item #: 12309 -
New Legendary Series 17x8" Glossy Finish Magnum 500 wheel for your Mercury Cougar or Ford Mustang. While they look almost identical to the original chromed steel version, these are actually a lighter, better-balanced aluminum alloy with a protective coating. These wheels come with free chromed plastic center caps. The caps have a red Legendary logo but we can include at no cost, a set of black and chrome walking cat decals (click here). Just add it to your cart if you'd like these decals. If...
Availability: Ships Direct from Supplier (Except International)
Item #: 12980 -
New Legendary Series 15x7" Charcoal Finish Magnum 500 wheel for your Mercury Cougar or Ford Mustang. While they look almost identical to the original chromed steel version, these are actually a lighter, better-balanced aluminum alloy with a protective coating. We also have center caps for these wheels that feature the Mercury man or the walking cat logo. Center caps and lug nuts sold separately. These wheels come with free chromed plastic center caps. The caps have a red Legendary logo but we...
Availability: Ships Direct from Supplier (Except International)
Item #: 32003 -
New Legendary Series 15x7" Stealth Black Finish Magnum 500 wheel for your Mercury Cougar or Ford Mustang. While they look almost identical to the original chromed steel version, these are actually a lighter, better-balanced aluminum alloy with a protective coating. These wheels come with free chromed plastic center caps. The caps have a red Legendary logo but we can include at no cost, a set of black and chrome walking cat decals (click here). Just add it to your cart if you'd like these...
Availability: In-Stock Item
Item #: 31133 -
Machine hex bolt for installing the heater cables to the climate controls on any 1969-73 Mercury Cougar or Ford Mustang. 8-32 threaded hex machine screw like the originals. Attaches cables for heater only or factory A/C cables.
Availability: In-Stock Item
Item #: 41777 -
Reproduction A/C discharge service valve that fits on top of the compressor and is an exact copy of the original. Verify your high pressure hose size when ordering, this unit has the 3/4" fitting. This valve accepts the R134A connection, not the R12.
Availability: In-Stock Item
Item #: 41778 -
Reproduction A/C suction service valve that fits on top of the compressor and is an exact copy of the original. Verify your high pressure hose size when ordering, this unit has the 7/8" hose fitting. Replaces part # D0AZ-19752-A or D0AA-19752-A.
Availability: In-Stock Item
Item #: 41441 -
This is used on cars equipped with factory A/C to stop the flow of warm coolant when the A/C is on. Not an exact replacement, but it will work just fine. Replaces Ford part #: D4AZ-18495-A.
Availability: In-Stock Item
Item #: 41776 -
Expansion valve for factory air conditioning for the Mercury Cougar or Ford Mustang.Will work with both R12 and R134 systems.Replaces part #: D1ZZ-19849.
Availability: In-Stock Item
Item #: 41783 -
Exact replacement to original drier that removes moisture and should be changed anytime system is recharged. It really is the life of your system. This stainless steel filter element stops contaminants from clogging the expansion valve.
Availability: In-Stock Item
Item #: 41914 -
High quality and correct looking air conditioning discharge hose for Mercury Cougars or Ford Mustangs. This hose is compatible with both 134a and R12 refrigerants.
Availability: In-Stock Item
Item #: 53245 -
Backup light switch retainer for Hurst shifters as installed on 1970-73 Mercury Cougar, Ford Mustang, and most vintage Ford cars with factory installed Hurst shifters.
Availability: In-Stock Item
Item #: 11297 -
Backup light switch for factory installed Hurst competition shifters from 1970-73. This is a Daniel Carpenter reproduction, these are still being made by Hurst in small quantities (see our premium version). It does not include the bracket for holding the switch.Listed in the Motorcraft catalog as SW-943Also fits:CometFairlaneMontegoTorino Check out our video on rebuilding your shifter below: ...
Availability: Used / Wrecking Yard Item
Item #: 25202 -
Used 14x7" styled steel wheel for your Mercury Cougar. This painted Kelsey Hayes wheel used with small cap and brushed finish trim ring that are sold separate. Cap and lugs are sold separately. Total width is 8" with a backspacing of 4".Ford part # D0ZZ-1007-C.
Availability: Used / Wrecking Yard Item
Item #: 15163 -
Cast iron pedestal mount for the air conditioning compressor on all 1970 - 1973 Mercury Cougars and Ford Mustangs with the 351C engine, both the H code 351-2V and M code 351-4V engines. Ford MPC part # D0ZA-2882-C.
Availability: In-Stock Item
Item #: 14326 -
This hose connects the sight glass hose to the air conditioning dryer. Includes the sight glass to dryer hose. Ford Part #: D1ZA-19835-A.This hose is compatible with both 134a and R12 refrigerants.
Availability: Used / Wrecking Yard Item
Item #: 25384 -
Regardless of which V-8 engine, D1ZA-19972-AA or D1ZA-19972-AB part number. This hose is approximately 24 inches long. These used hoses probably still hold pressure, we suggest a purchase of new 'O' rings prior to installation.
Availability: Used / Wrecking Yard Item
Item #: 25383 -
Regardless of which V-8 engine, D1ZA-19867-BC part number. This hose is approximately 49 inches long.
Availability: Used / Wrecking Yard Item
Item #: 24426 -
This is actually a kit which includes 2 hoses (Part # D1ZA-19835-A and Part # D1ZA-19837-A), the sight glass (Part # SG3, D2AZ-19D695-BK or YF-342), 2 o-rings (Part # L33,D2AZ-19D695-R or YF-368 and Part # H33, D2AZ-19D695-AE or YF-316) and a quick connect (Part # QF3,C1SZ-19B696-A or YF-241 and Part # QM6, C1SZ-19B695-A or YF-252). *Note we normally supply the new coupler with this kit. Regardless of which V-8 engine, this hose when assembled is approximately 78 inches long.Ford MPC kit #...
Availability: In-Stock Item
Item #: 11087 -
Self adhesive cork insulation tape for use on any 1967-73 Mercury Cougar or Ford Mustang with air conditioning. This is original style insulation wrap that adheres firmly to all metals. Material is 1/8 inch thick, and 2 inches wide, comes in a roll of 3 foot length. Perfect material for wrapping expansion valves, and joints prone to condensation.
Availability: Used / Wrecking Yard Item
Item #: 31915 -
Used A/C suction service valve for 1970-73 Mercury Cougars and Ford Mustangs equipped with factory or integral A/C. Original assembly line used low pressure or suction valve for installation on either York or Tecumseh air compressors. Has the 7/8" inch 'O'-ring fitting for suction hose. Note that this has the O-ring style of hose connection, also 'Rotolock' is used to describe this style of valve. We consider these core grade valves. They should be professionally inspected and have...
Availability: Used / Wrecking Yard Item
Item #: 31916 -
Used A/C discharge service valve for 1970-73 Mercury Cougars and Ford Mustangs equipped with factory or integral A/C. Original assembly line used high pressure or discharge valve for installation on either York or Tecumseh air compressors. Has the 3/4" inch 'O'-ring fitting for discharge hose. Note that this has the O-ring style of hose connection, also 'Rotolock' is used to describe this style of valve. We consider these core grade valves. They should be professionally inspected and...
Availability: Ships Direct from Supplier (Except International)
Item #: 17791 -
These reproduction convertible panels only come in black and are sold as a pair. They DO NOT have the holes cut in them for the retracting seat belts, so 72 and 73 Cougar owners will need to cut these holes. In addition, you will have to cut the holes for the ashtray and power window switch or manual window crank as well as install the snaps for the top boot. This will of course require that you have your old panels to use as a guide. These panels are not as thick as the originals and if you...
Availability: Used / Wrecking Yard Item
Item #: 22989 -
Used bracket for installing the rear interior panels on any 1971-73 Mercury Cougar or Ford Mustang convertible. One bracket per side. These brackets will have a bit of dirt and or rust on them, originally painted chassis black. Replaces Ford part number D1ZZ-76310A84-A.
Availability: In-Stock Item
Item #: 42117 -
This is an inexpensive top that is only recommended if you car is going to be stored indoors. Have you ever wondered how a convertible top is installed, or maybe considered trying it yourself? Check out our in-depth installation video below! ...
Availability: Ships Direct from Supplier (Except International)
Item #: 71-72-73-Conv-Tops -
Currently, Convertible Tops dropshipped from this supplier will not ship for 4-6 weeks.
The original tops would have been double texture PinPoint Vinyl.
There are 3 different materials currently offered for these premium tops.
Single Texture PinPoint Vinyl (GOOD):
This is the material that is offered by almost all Mustang Vendors and it looks the same on the surface as an OEM top.
This is a two-ply composite which has an outer layer of canvas-looking PVC vinyl plastic, and an inner layer of...
Availability: Used / Wrecking Yard Item
Item #: 11906 -
Good used 10 blade alternator fan.Ford Part #: DOAZ-10A310-B.
Availability: Used / Wrecking Yard Item
Item #: 11907 -
Used alternator fan spacer for the 1967 - 1973 Mercury Cougar or Ford Mustang. This spacer also fits many other Ford applications. Ford part number: C5AZ-10A344-B.
Availability: In-Stock Item
Item #: 11-0053 -
Used quarter window lower window guide stop. Made of black plastic, held on by a single bolt. Mounts to the window guide on any 1971-73 Mercury Cougar or Ford Mustang Coupe or convertible. One per side, sold individually.Replaces part # D1ZZ-6539805-A.
Availability: Used / Wrecking Yard Item
Item #: 15133 -
Used front support bracket for the air conditioning compressor assembly. Starting in 1971, Ford eliminated the idler pulley and used this bracket in it's place. Replaces part # D1AZ-2888-B.
Availability: Restored / Remanufactured
Item #: 11-9910 -
Service replacement A/C belt tensioning pulley with new installed bearing. This adjustable bracket and pulley can be used on all 1968 - 1973 Cougars or Mustangs with the V-8 engine as long as they have the "stamped steel" lateral air compressor support brackets. This bracket will only have the big bearing pulley and may have various casting numbers such as D5TA-8A617, D3OA-8A617, D5OA-8A617, D8OA-8A617, etc.*Note* All new bearings will have a slight bit of play in them. This is by design, by...
Availability: Used / Wrecking Yard Item
Item #: 24502 -
Fan spacer measuring 1-1/4 inches. Application includes 1969 Mercury Cougar and Ford Mustang with Boss 302 or 428 Super Cobra Jet engines. Additionally it was likely used on 1971 cars with 351-2V engines and standard cooling. Reference number YA-20, cross reference to D1OA-8546-AA spacer.Ford part # C8YE-8546-A, Ford engineering number C8YZ-8546-A.
Availability: Used / Wrecking Yard Item
Item #: 25285 -
Fan spacer, measuring 1-1/4 inches, but referenced at 1-9/32" too. Application includes 1971 - 1973 Mercury Cougar and Ford Mustang with 351-2V engines and standard cooling. Reference number YA-20, cross reference to C8YE-8546-A spacer.Ford part # D1OA-8546-AA, Ford engineering # C8YZ-8546-A.
Availability: Used / Wrecking Yard Item
Item #: 24395 -
Fan spacer, measuring 1-1/2 inches. Application includes 1969 Mercury Cougar and Ford Mustang with 351-2V engines and standard cooling. Reference number YA-21, cross reference to D0AE-8546-B spacer.Ford part # C8OE-8546-A, Ford engineering # C5DZ-8546-B.
Availability: Out of Stock
Item #: 10196 -
These are used hose clamps that bolt to the body and lateral A/C bracket. These were dipped in a rubber like substance to prevent chaffing. The ones that we have available may have some cracking or damage to this coating. It should be easy to 'dip' them again with the product that is available in most hardware stores. We normally see 2 of these clamps, securing the hoses on most cars. Replaces Ford part number 374125-S100.
Availability: Out of Stock
Item #: 10197 -
Exact reproduction pair of originals and a must for that detailed engine compartment, but in stainless steel. It is little details like these that will often separate 1st from 2nd place at a show.Replaces Ford part # C5ZZ-19752-C.
Availability: Used / Wrecking Yard Item
Item #: 11940 -
Original used male half of the factory air conditioning coupler for all 1967-73 liquid line or sight glass hoses. Brass construction, includes the plunger and spring. Also sold as a two piece kit which includes the male and female components. Replaces Ford part number C1SZ-19B595-A.
Availability: Out of Stock
Item #: 24993 -
Fan spacer, measuring 2-1/4 inches or sometimes mentioned as 2-8/32". Application includes 1970 Mercury Cougar and Ford Mustang with Boss 302 engines, or 351 engines with extra cooling or air conditioning. Reference number YA-31.Ford part # D0AE-8546-A, Ford engineering # D0AZ-8546-A.
Availability: Used / Wrecking Yard Item
Item #: 24338 -
Fan spacer, measuring 2-7/16 inches, sometimes mentioned as 2.44". Application includes 1971 Mercury Cougar and Ford Mustang with 351 engines and air conditioning. Reference number YA-74.Ford part # C8AE-8546-E, Ford engineering # C4AZ-8546-F.
Availability: Used / Wrecking Yard Item
Item #: 24339 -
Fan spacer, measuring 2-5/8 inches, sometimes mentioned as 2.62". Reference number YA-75.Ford part # C8AE-8546-F, Ford engineering # C4AZ-8546-G.
Availability: Used / Wrecking Yard Item
Item #: 25492 -
Fan spacer, measuring 2-5/8 inches. Application 1972 - 1973 Mercury Cougar and Ford Mustang with 351-4V or 351CJ, and all 1971-72 351's with air conditioning. Reference number YA-75.Ford part # D2AE-8546-AA, Ford engineering # C4AZ-8546-G.
Availability: In-Stock Item
Item #: 10895 -
Reproduction radiator fan spacer for fixed or flex fans. Can be used on 1967-73 Mercury Cougar and 1964-73 Fords and Ford Mustangs. Ideally the various length spacers were used to place the fans half way into the fan shrouds for optimal cooling. Original Ford part number C4AZ-8546-A.
Availability: Out of Stock
Item #: 10460 -
1973 Mercury Cougar and Ford Mustang shifter handle for automatic transmissions with selector button and set screw. Starting in 1973 Ford stopped using the deluxe handles with faux leather and eliminated the dummy button on the right side of the handle. Ford part numbers D3OZ-7213-A and 1973 black plastic push button. Check out our video on rebuilding your shifter below: ...
Availability: Out of Stock
Item #: 10468 -
Black plastic shifter bezel / indicator assembly for all 1971-73 Mercury Cougar and Ford Mustangs. Good used bezel for use with or without console or consolette. The chromed metal 1969-1970 version of this shifter cover is a very nice upgrade for 1971-1973 owners. Replaces Ford part # D1ZZ-7D443-A. Check out our video on rebuilding your shifter below: ...
Availability: Out of Stock
Item #: 19462 -
Used lamp diffuser for all 1969-73 Mercury Cougar and Ford Mustangs. Note the comparison picture. The reproduction is a shade or two lighter than original. The complete Ford part number is not available, the basic part number for this item is 15811. Check out our video on rebuilding your shifter below: ...
Availability: Out of Stock
Item #: 10491 -
Ford called this part a 'sleeve'. Attaches to the lower shifter arm with a hitch pin. Has nice bushing, with correct nut, washer, and pin. The 1967/68 and 1969/73 versions are identical. The C1AA-7353-C sleeve has fine threads, the C9OZ-7353-A has course threads. Fits all 1967-73 Mercury Cougar and Ford Mustang, and we suspect many other Ford vehicles beginning in 1961. Check out our video on rebuilding your shifter below: ...
Availability: Out of Stock
Item #: 16-0024 -
Used original pan removed from a Western parts car, 14 bolt holes. This pan is not available new. These will have some dents and or scrapes. These were not painted originally, may have light rust that will clean up. Consider them Grade B used.
Availability: Out of Stock, On Order
Item #: 13959 -
Stunning quality and far less likely to crack than the originals. The 67 version was actually a little different than 68 - 73 but you would have to look close to see the difference. Check out our video on rebuilding your shifter below: ...
Availability: Out of Stock, On Order
Item #: 13958 -
Stunning quality and far less likely to crack than the originals. The 67 version was actually a little different than 68 - 73 but you would have to look close to see the difference. Check out our video on rebuilding your shifter below: ...
Availability: Out of Stock
Item #: 16-0074 -
Application for all 1971 - 1973 Cougars with factory C6 automatic transmission. Also the correct application for those wanting to install a small block C6 in their 1967 - 1970 Cougar. Original engine options include 351-2V, 351-4V, and 429CJ. We have found two versions of this crossmember, one with three holes in the middle section where the rubber isolator mounts and one with two. This part weighs 2.96 pounds and when set on a level surface, the height of the mounting hole on the driver side...
Availability: Out of Stock
Item #: 25267 -
Used cigar or cigarette lighter socket and retainer assembly for 1971-73 Mercury Cougar and Ford Mustang. Ford part # D1ZZ-15052-A.
Availability: Out of Stock
Item #: 10940 -
Good used power steering pressure line hose retainer. Mounts on top of the shock tower brace as shown. Comes as shown with used rubber insulator. Fits all 1971-73 Mercury Cougar and Ford Mustangs with V-8 engines.
Ford part # D1ZZ-3C510-A.
Availability: Out of Stock
Item #: 16-0064 -
Used on both 351 2V and 4V motors equipped with the C6 transmission. Approximately 26-1/2" with red color code. The comparison picture with two rods side by side are the 71 - 73 FMX and C6 rods. *NOTE* Many assume the C6 was only available with a 351 equipped with a 4V but in fact you could get a C6 with a 351 2V in 1971 - 1973.
Availability: Out of Stock, On Order
Item #: 26724 -
Although this premium reproduction strut rod bushing kit appears very similar to the economy kit, they are in fact superior. The main difference being that the bushings are made from a higher quality rubber compound.Replaces Ford Part #: C6OZ-3A187-AR.
Availability: Out of Stock
Item #: 25404 -
Good used bezel with appliqué still intact. Ford part number D1ZZ-13932-A.
Availability: Out of Stock
Item #: 19587 -
This restored three spoke, rim blow steering wheel was used on all Cougars 1970-73 except the Cougars equipped with standard interior or on rare occasion the 1973 Cougars that came with the rare 2 spoke leather wrapped wheel. The Cougars equipped with standard interior used a two spoke wheel with the horn button located in the center pad. If you choose to send in a core for exchange it will need to be a clean one as we will not restore steering wheels that have huge cracks, severe UV damage or...
Availability: Out of Stock
Item #: 12728 -
These are cracked core wheels as taken from a parts car. The Center pad is not included and you can count on the rubber switch being rock hard. This wheel is for restoration purposes and we cannot guarantee that we will have all colors in stock at all times. The three wheels shown here are random examples and are not what you will actually be getting when you order. Most colors in stock, call for color, or leave desired color in the comments section of your order. ...
Availability: Out of Stock, On Order
Item #: 10909 -
Basic kit for rebuilding your Ford Autolite or Motorcraft spread bore 4300D or 4 barrel carburetor with large secondary venturis. Covers all factory 4 barrel carburetors for all 1972-73 Mercury Cougar and Ford Mustang with Autolite or Motorcraft 4300 carburetors. Excludes earlier square bore 4300 carburetors.
Availability: Out of Stock
Item #: 25595 -
D3ZE-9A589-AB Factory 1973 Autolite / Motorcraft 4300 Carburetor spacer plate with attached EGR valve. The exhaust gas recirculation valves started showing up on American cars in 1973. There will be almost always some erosion from the heated exhaust gases. This is for use with the Motorcraft 4300 carburetor with Ford part number D3ZF-MA.
Availability: Out of Stock
Item #: 25556 -
1973 351-2V Motorcraft 2100 Carburetor, automatic transmissions - both FMX and C6. D3AF-DC stamped on the carburetor base, spreadbore design of 351 cfm. Rebuildable core carburetor with proper numbers, we don't always have the factory Ford Autolite tag that was affixed to the top.
*Trivia - all 1973 Cougars with a H code 351-2V engine were automatics, no manual transmissions built.
Availability: Out of Stock
Item #: 25599 -
1973 351CJ-4V Motorcraft 4300D Carburetor, automatic C6 transmission- 50 states. D3ZF-MA stamped on the carburetor base, spreadbore design of 715 cfm. Rebuildable core carburetor with proper numbers, we don't always have the factory Ford Autolite tag that was affixed to the top.
Availability: Out of Stock
Item #: 25598 -
1973 351CJ-4V Motorcraft 4300D Carburetor, 4 speed manual transmissions- 50 states. D3ZF-LA stamped on the carburetor base, spread-bore design of 715 cfm. Rebuildable core carburetor with proper numbers, we don't always have the factory Ford Autolite tag that was affixed to the top. This unit was actually rebuilt and never used.
Availability: Out of Stock
Item #: 24363 -
This is an original chrome lock knob used on 1968 and up Fords with no peeling chrome or obvious scratches. If you compare the originals to the reproductions we have listed you will see a distinct difference. This is for the very particular restorer who really is concerned about detail, especially on prominent pieces like this. Sold individually, very limited supply.Original Ford part number is C8AZ-6221850-A
Availability: Out of Stock
Item #: 25299 -
1971 - 1973 Cougar wiper control switch knob. In early (May 3, 1971) Mercury changed the knob. This is the later knob. Hex shaped knob, good used, may show some minor wear.
Availability: Out of Stock
Item #: 10877 -
Used in-tank, fuel sending unit without the low fuel option. Tested and cleaned units for all 1971-73 Mercury Standard model Cougars and all Ford Mustangs with 22 gallon fuel tanks. This is an original 1971-73 fuel sending unit with two electrical prongs. Ford casting number D1ZF-9275-AB. This unit comes with a new 3/8 inch filter, brass float, and sending unit gasket. *Note - Not compatible with Mercury Cougar XR7 models with low fuel warning light. The sending units with low fuel have 3...
Availability: Out of Stock, On Order
Item #: 41595 -
These stainless steel tubes are made to exact O.E.M. standards and specifications. All choke tubes have the proper fiberglass insulation, fittings, rubber hose, and S-clip.
Availability: Out of Stock
Item #: 14292 -
Cast construction with very good quality chrome. Looks great with chrome valve covers and air cleaner. Replaces Ford Part #: D0ZZ-8592-A.
Availability: Out of Stock, On Order
Item #: 42052 -
Reproduction chrome heater hose elbow is for 351, 390, and 428CJ engines. Replaces Ford Part # D0AZ-18599-C Barbed End: 5/8" hose barbThreads: 1/2" NPT (Tapered Threads) For some helpful tips on upgrading your Cougar (or Mustang) cooling system, check out our video: ...
Availability: Out of Stock
Item #: 27500 -
NOS Water bypass plate for all Ford 351C engines. This is an original in the package brass restrictor plate for 1970-73 Mercury Cougar or Ford Mustang Torino etc.Limited to stock on hand. Replaces Ford Part number D0AZ-8K517-A. For some helpful tips on upgrading your Cougar (or Mustang) cooling system, check out our video: ...
Availability: Out of Stock, On Order
Item #: 12979 -
This fail safe thermostat can save you from costly engine damage during an overheat. They feature an exclusive technology that locks the valve open position if overheating occurs. This allows for maximum coolant flow when you need it most.
Availability: Out of Stock, On Order
Item #: 25395 -
D1ZE-6312-C Application - Q code 351 Cobra Jets with air conditioning and power steering. Triple sheave pulley, 6-11/16" and 7-9/16" diameters. Ford Master Part number D1ZZ-6A312-A.
*Note - References also list casting number D1ZE-6312-CA as being the same.