All Available Parts - 1973 Ford Mustang

*NOTE - These knobs are NOT in the original Ford packaging, they were bought in bulk from a supplier who did not provide packaging. This style of knob was used on almost all Ford products starting in 1968 and continuing on through the late 1970's. The latest renditions in reproduction form are actually pretty good but for the purist these make a nice touch. Paste the part number into the Ebay search box and sometimes you can get lucky and get a pair for under $30. Limited supply, original...

New old stock driver side (left hand) vertical quarter window weatherstrip for the Mercury Cougar or Ford Mustang. Ford part number D1ZZ-6530147-A.

NOS distributor lead wire with green boot for the coil. Direct replacement for 1968-73 Ford distributors. There were several colors of boots that go to the coil, this is a green one as shown. Ford part number C7VY-12216-A.

NOS distributor ground wire. Direct replacement for 1967-73 Ford distributors. New old stock cable for inside the distributor, non ferrous metal, brass? Ford part number D2AZ-12264-A.

NOS ignition switch. 1973 version has a longer pigtail, and has a shield or tube covering the wires. This is only the electrical side, the mechanical key and lock section is not included. See appropriate shop manual for proper alignment and installation. Tested and working ignition switch. New Old Stock still has the white plastic pin installed, needs to be removed prior to installation. The pin prevents the plunger from moving around in storage. Ford part number D3AZ-11572-A. ...

When it's time to replace your old decaying foam seal, go with our reproduction weatherstrip retainer foam roll with peel off adhesive. Goes between the roof and door / window channel.  These are not technically manufactured to fit the Cougar / Mustang, however these are very close to the originals and come from the manufacturer in a roll that is 4' X 1" X 1/8".  One roll is more than enough to do one side, but you will need 2 rolls to do both sides. ...

Replaces Ford part #: D2WY-6543720.

This great fitting reproduction emergency / parking brake pedal pad for the Mercury Cougar or Ford Mustang. This is supposed to have a stainless steel retaining ring around the perimeter. We carry both reproduction and used. Replaces Ford part # C9ZZ-2454-A.

Replaces Ford part #: D1ZZ-7653986. Seven piece kit with attaching hardware.

Replaces Ford part #D1ZZ-7602626

Replaces Ford Part # : D1ZZ-7651325-A

Made from fuel resistant cork like original.  Modeled off the Mustang \ 69 Cougar gasket which has 5 screws (67-68 Cougar only used 4 screws), but works for any 67-73 Mustang / Cougar. For 67-68 Cougar applications you will have to just screw through the cork. We can say with out a doubt, that in both Dearborn and San Jose, the factory workers did not use the pre-drilled holes when installing the fuel filler necks. We have suggested that the supplier not make them with holes. Probably...

Nice new black moulded plastic gas pedal pad for all 1971, 1972 and 1973 Mercury Cougars regardless of engine or transmissions. Replaces Ford Part #: D1ZZ-9735 and D1ZZ-9735-A

These Radiator Hood Support Bumpers reproductions are sold as a pair. They fit the 67, 68, 69, 70, 71, 72, and 73 Mercury Cougar. Replaces Ford part #: C5ZZ-16763.

This is the type of material that was used to install gasketless windshields starting in 1969. Tom

Rubber plugs for sealing the holes in the firewall of any 1967-68 Mercury Cougar or Ford Mustang. These plug the firewall holes if you don't have air conditioning or if you have deleted your heater core. Fits 1" body panel holes for all years.Sold as a pair.Original Ford part 377678-S2

New rubber body plug, fits 3/4 inch normal gauge sheet metal panel holes. These are found on various places throughout classic Ford and Mercury vehicles. Some locations include: frame rails at sway bar, rear floor pan, LH fender apron.Sold individually, also sold in kit or assortments for Cougar and Mustangs.Replaces Ford plugs marked 377977.

New rubber body plug, fits 9/16 inch normal gauge sheet metal panel holes. These are found on various places throughout classic Ford and Mercury vehicles, typically they are for: front fender aprons, transmission cross member, and radiator support. Sold individually, also sold in kit or assortments for Cougar and Mustangs.Replaces Ford plugs marked 376966.

New rubber body plug, fits 1-3/4 inch normal gauge sheet metal panel holes. These are found on various places throughout classic Ford and Mercury vehicles. Typical application is rear leaf spring access.Sold individually, also sold in kit or assortments for Cougar and Mustangs.Replaces Ford plugs marked 377356.

New rubber body plug, fits oval rear shock access hole. 1-3/4" x 3-3/8" oval holes. Sold individually, Usually 1 per car. Fits 1971-73 Mercury Cougar and Ford Mustang.Replaces Ford plugs marked 384440.

New rubber body plug, fits 13/16 inch normal gauge sheet metal panel holes. These are found on various places throughout classic Ford and Mercury vehicles. Some locations include: trunk floor pan, side of cowl at door, and LH apron.Sold individually, also sold in kit or assortments for Cougar and Mustangs.Replaces Ford plugs marked 377949.

Reproduction rubber body plug for the Mercury Cougar and Ford Mustang. This 11/16" x 15/16" oval unit fits to the top of the cowl underneath the front fenders. These little units are sold individually, and their are usually two required per car. Replaces Ford plug marked 383181-S.

New rubber body plug, oval , fits inner frame rails. 3/4" x 1" oval holes. Sold individually, Usually 2 per car. Fits 1967-73 Mercury Cougar and Ford Mustang.Replaces Ford plugs marked 378770-S.

Reproduction rubber grommet for the air conditioning case. This grommet encloses the tubes for the evaporator, and slides into a slot on the heater box. Owners with 1969 A/C please look at your existing grommet for the triangle shape like in the picture. Fits some 1969 Mercury Cougar and Ford Mustang (late built cars), and should be all 1970-73 Mercury Cougar and Ford Mustang. Replaces Ford part number C9ZZ-19B552-A. Check out our video below on how to replace a heater core! We used a '69...

New rubber boot for brake push rod to the master cylinder on all drum brake cars. Fits all 1967-72 Mercury Cougar and 1965-73 Ford anything cars, including Mustang.Trivia - Did you know that 100% of all 1973 Mercury Cougars, came from the factory with front power disc brakes?

Reproduction foam rubber donuts that help cushion the brace from the tail panel on any 67 - 73 Cougar or Mustang.Replaces Ford part number C5ZZ-6540996Sold as a set of 4.

Reproduction Concours correct windshield washer hose with ribbed outer wall. Hose is 101" and is cut-to-fit.Tee connector not included, you can find it here.You can find the nozzles here.

Reproduction heater core tube gasket for the 1971 - 1973 Cougar or Mustang. Never sold as a service part by Ford, this gasket seals the area around the heater core tubes where they pass through the vehicle's firewall. The gasket is cut from closed cell EPDM foam sponge rubber that matches the original material used by Ford. Designed to withstand the temperatures found under the hood and surrounding the heater core tubes. ...

Economy overseas reproduction door perimeter seal. These glue to the perimeter of the doors and are held in by screws on both ends. Sold as a pair. Replaces Ford part #D1ZZ-6520530-A.

Shrink-on plastic sleeve that is found on the lower part of the collapsible steering columns. Used sleeves are often ripped and torn. Simply cut off your old sleeve and install this item to give your column a newer look and feel. Installation: Make sure that your column is clean. Lube the column and inside of the sleeve. Do not remove the crease on the plastic, you need it to help you put the sleeve on the tube. Push the sleeve on as far as you can. Gently tap the sleeve down on a table top...

This is the 3 hole version of the ball joint for the 1967 - 1973 Cougar and Mustang. Right is same as left. Two required per car. Hardware included. made in Tiawan.

Set of two polyurethane bushings that insert into the rear side of the lower control arm. This set contains two bushings that measure 1 7/16 across the leading inside edge, and 1 5/8 across the outer rim. Typically these bushings fit Ford factory installed lower control arms with the welded on jacking tabs. Note: These smaller diameter bushings were used on factory installed control arms. Service replacement control arms utilized 1-9/16 inch bushings.

Set of two polyurethane bushings that insert into the rear side of the lower control arm. This set contains two bushings that measure 1 9/16 across the leading inside edge, and 1 5/8 across the outer rim.Note: These larger diameter bushings were used on Ford service replacement lower control arms. Typically found on Ford supplied lower control arms without the welded on jacking tabs.

Oil seal for rear axle on any 1968-73 Mercury Cougar or Most Ford cars with 31 spline axles. Typically only 428CJ, 427-4V, and Boss 302's got the heavy duty 31 splined axles from the factory, most Cougar and Mustangs have 28 splined axles. Seal measurements: 1-1/2 inch inside diameter, 2-17/64 inch outside diameter. Two needed per axle, sold individually. We stock Timken brand of seals.Replaces Ford part number C7OZ-1177-A.

Oil seal for rear axle on any 1967-73 Mercury Cougar or Most Ford cars with 28 spline axles. Most all Cougar and Mustang received 28 splined axles, whether they have an 8 inch or nine inch rear end from the factory. Seal measurements: 1-3/8 inch inside diameter, 2-17/64 inch outside diameter. Two needed per axle, sold individually. We stock Timken brand of seals.Replaces Ford part number C7OZ-1177-B.

3M brand windshield to channel adhesive. This is what is used for installing the windshields on 69-73 Cougars and Mustangs

This kit is designed for the Mercury Cougar and Ford Mustang A/C box.Replaces part # D1ZZ-18500-A.Check out our video below on how to replace a heater core! We used a '69 Cougar with A/C, but many of the same concepts apply to other years.

These stainless steel radiator hood support bumper reproductions are sold as a pair. They fit the 67, 68, 69, 70, 71, 72, and 73 Mercury Cougar. Replaces Ford part #: C5ZZ-16763.

Reproduction driver side (left hand) vertical quarter window weatherstrip for the Mercury Cougar or Ford Mustang. This is a premium piece made with the original Ford tooling. Do you have questions about Glue-In vs Bolt-In glass? How about how to properly install Glue-In glass in your 1969 Cougar or Mustang? Check out our video below for some great glassy information! 1969 Glue-In Glass: The Comprehensive Repair Guide Video ...

Reproduction passenger side (right hand) vertical quarter window weatherstrip for the Mercury Cougar or Ford Mustang. This is a premium unit that made made with orginal Ford tooling. Do you have questions about Glue-In vs Bolt-In glass? How about how to properly install Glue-In glass in your 1969 Cougar or Mustang? Check out our video below for some great glassy information! 1969 Glue-In Glass: The Comprehensive Repair Guide Video ...

Premium reproduction rubber seal with the proper thickness of the 1967-68 seal as found on Mercury Cougar and Ford Mustang except these are not molded to the extension contours. Starting in 1969 this channel seal was manufactured slightly smaller which tightened up the gap on the fender and quarter extension seals. This seal maintains the slightly larger gaps. Sold as a pair, two pairs needed per car.  Each package has 2 strips of 25 1/2" lengths. *NOTE* Do not over tighten the...

Correct for your 1967-68 Cougar or Mustang with A/C, but will work just fine in all 1969-73 Cougars and Mustangs with A/C. These pieces are also an excellent option for 1969-73 Cougars and Mustangs without A/C because it will give your heater core a better tighter fit inside the heater box. If you choose to go this route on your 69-73 non A/C car, slight modification to the ends caps will be required to fit. Your just going to cut a hole in one of the end caps. Easy cheesy, no sweat.These are...

This is a much cheaper version of the foil sound deadeners and underlays we sell. This particular insulation is basically bubble wrap with two layers of foil on both sides. Good for insulating headliners, floor pans, trunk areas, door panels, kick panels and just about anything else you might want to use it for. This insulation comes in a 48" X 72" roll. Just grab a pair of scissors and cut your shapes. You can use any adhesive you like (contact cement or weatherstrip adhesive,...

This is a radio nut removal tool used to remove the radio shaft nuts. No more trying to remove those little units with the wrong tools and potentially damaging your bezel or dash. These are made from HRS steel and are milled to fit the shaft nut perfectly.

Set comes with economy grade pliers and 150 hog rings, enough for one bucket seat, probably two.

This is a mirror nut bezel tool used to remove the mirror nut on the 1967 - 1968 and 1970 - 1973 Cougar. No more scratches trying to remove with the wrong tools. These are made from HRS steel and are milled to fit the bezel nut. This tool pays for itself each time you use it. NOTE: This is an exact fit for ALL used mirror nuts (bezels) and the 1970 - 1973 reproduction mirror nuts (bezels). However, you will find it does not fit our 67-68 repro mirror nuts (bezels) and will need some...

New coil spring compressing tool to compress the coil springs of the 1967-73 Mercury Cougar or 1965-73 Ford Mustang. This tool now comes with a bearing to make the job much easier. This spring compressor is a must for safely removing front coil springs. We also offer a 60 Day Loaner if you only need the tool for a short period of time. *NOTE* Not recommended for heavy duty coil springs like found on pickup trucks and full sized cars. ...

We will loan this coil spring compressor for 60 days, with a 100% refundable purchase price. This tool now comes with a bearing to make the job much easier. Only available to customers that purchase our front suspension rebuild kits. Tool must be returned in undamaged condition with no missing parts within the 60 day time period. Returns past 60 days are subject to a 25% restocking fee. Coil spring compressing tool, this is a must for safely removing front coil springs on any 1967-73...

New strip caulk for the Mercury Cougar or Ford Mustang. These units come in one foot strips and are used for sealing the front fenders to top of aprons and for sealing the fuel tank flange to the trunk floor. They are also used for sealing the floor drain plugs, gas filler necks, door panel water shields, plus many other components that are fastened to the body. This box contains 60 individual strips of black non-hardening caulk.

No more crust, white powdery battery terminals. Just spray this stuff on, and after a few minutes....simply wash off with water! Not only can you use this stuff on your car, you can use it on your ATV's, quads, dirt bikes and even your ride on lawnmower! A handy item to have laying around your garage. Of course, there's a little more messy, mostly free alternative which you can find the ingredients for online, but why bother? This is a simple, fairly cheap product to have.  

Permatex RTV gasket maker for the automatic transmission in your Mercury or Ford. Great stuff for sealing up that leaky transmission pan gasket!

New adhesive / epoxy applicator to apply our 3M window adhesive to the glass (or whatever else needs bonding) in your Mercury or Ford. This non-drip unit features an easy loading breech, a 1:1 mixing ratio and full cartridge support. We also offer a 60 day loaner if you only need this unit for a short time. ...

New red permanent strength thread locker for your project. This is a must have item if you are reassembling your pride and joy after restoration or just changing out parts. Often times, the vibrations from these antiques can vibrate loose the fasteners used to hold it together. If you use this, you can rest assured that your Merc or Ford will not fall apart from fasteners that have vibrated loose.

New RTV gasket maker for use on the differential of your Mercury or Ford. This gasket maker is specially formulated to withstand today's gear oils and prevent leakage.

New thread sealant specially formulated to seal liquid in high temperature applications.

New blue removable strength thread locker for your project. This is a must have item if you are reassembling your pride and joy after restoration or just changing out parts. Often times, the vibrations from these antiques can vibrate loose the fasteners used to hold it together. If you use this, you can rest assured that your Merc or Ford will not fall apart from fasteners that have vibrated loose.

CRC contact cleaner is intended for cleaning sensitive electronics and electrical equipment. Great for cleaning edge connectors, buss bars, circuits, contacts, printed circuit boards, switches, circuit breakers, etc. Safe on most plastics.

Clever tool that keeps the piston stationary in your brake distribution block. It is as simple as centering the piston and screwing in this tool, of course your have to catch the groove in the piston. Leave in until brakes are completely bled and functioning. Remove and install your brake warning light switch.

Professional grade paintless dent removal kit. This kit is designed to work with smaller blemishes such as dents from hail, door dings, etc. Complete with universal high strength glue sticks, puller, and a variety of different sized gluing tabs. NOTE: Remove glue with 91% alcoholAlthough we work with 67 - 73 Cougars and Mustangs, this kit is good for a wide variety of different vehicles.

The POGO Stick works just like the larger Hustler stick but is much easier to ship. If you need more leverage you can just add a pipe for leverage. We will loan this hustler stick for 60 days, with a 100% refundable purchase price. Tool must be returned in undamaged condition with no missing parts within the 60 day time period. Returns past 60 days are subject to a 25% restocking fee. Check out our video below: ...

Adapter tool for installing and removing remote door mirror bezels on 1967-68, and 1970-73 Mercury Cougar and Ford Mustang. Should be coupled with the basic tool (item 32368) A 5/32" Allen wrench is needed to attach tools together. Allen wrench not included. *Note - Excludes 1969 remote mirror bezels. ...

Used flexplate reinforcing ring, Ford called it a fly wheel reinforcing plate. Fits all Ford small block engines including 260, 289, 302, 351W and 351C. Strengthens the area where the automatic transmission flex plate mounts to the crankshaft. This is not just a ring with 6 holes in it, it is indexed specifically for the flex plate and only goes on one specific way. It has to be indexed because of the weight on the flex plate. Just under 4 inches in diameter. Special bolts not included, but...

Reproduction Replacement for the Rear License Plate Lens for the 1969 - 1973 Mercury Cougar or Ford Mustang.  We also have good used original OEM lens that can easily be cleaned to look as good as these Chinese reproductions. Replaces Ford part #: C4AZ-13564.

Good used passenger side trunk or deck lid hinge. Fits all 1972-73 Mercury Cougar and Cougar convertible models. Additionally fits 1972-73 Mustang hardtop and convertible models (body style 65 and 76). We also sell the driver side hinge individually. Ford part number D1ZZ-6542700. Sometime in 1972, the hole spacing for the trunk lid changed from 3 inches to 4-1/4 inches spacing. This hinge will have the 4-1/4 inch spacing. These are welded to the body, expect some cleanup to the metal prior to...

Good used driver side trunk or deck lid hinge. Fits all 1972-73 Mercury Cougar and Cougar convertible models. Additionally fits 1972-73 Mustang hardtop and convertible models (body style 65 and 76). We also sell the driver side hinge individually. Sometime in 1972, the hole spacing for the trunk lid changed from 3 inches to 4-1/4 inches spacing. This hinge will have the 4-1/4 inch spacing. These are welded to the body, expect some cleanup to the metal prior to welding. We do not drill spot...

Threaded anchor that slides into the trunk hinge on each side. Sold individually, two needed per car. These are for Cougar and Mustang built after approximately 3/31/1971. Look for bolt spacing of 4-1/4 inches on those trunk lids.  Ford number C9AZ-6242752-A.*Note - Trunks prior to March 31, 1971, did not use this anchor plate. I think that they had a bolt spacing of 4-1/2 inches.

This is the modern version of the Kelsey Hayes wheels that were originally equipped on 1967 Shelbys. One-piece cast aluminum structure with a CNC machined face and durable clear coat finish. The lighter weight one piece design also provides a significant weight savings over the original steel design, delivering improved acceleration and braking performance. These take specific lug nuts and center caps (sold separately, see related items). These wheels come with free chromed plastic center...

This is a used windshield wiper delay governor, or module, and is a black box that mounts under the dash to the left of the radio. Sometimes called interval or delay wipers. *NOTE* Must be used in conjunction with a intermittent wiper switch.Part # D1ZB-17C476, D2ZB-17C476, MPC # D1ZZ-17C476-A.

This is a used intermittent wiper delay switch which is sometimes called the intermittent wiper delay module. The intermittent wiper delay switch can be identified by a grounding wire that is attached to the housing. Sometimes interval or delay is used in place of intermittent for this unit.*NOTE* Must be used in conjunction with an intermittent wiper controller.Replaces part # D1ZB-17A553-BB, D2ZB-17A553-AA, MPC # D1ZZ-17A553-B.

Includes the controller and switch to convert your standard two speed wiper system over to delay wipers.Controller part #  D1ZB-17C476, D2ZB-17C476, MPC # D1ZZ-17C476-A.Switch part # D1ZB-17A553-BB, D2ZB-17A553-AA, MPC # D1ZZ-17A553-B.

Aluminum flexible tube that connects the vapor canister to the air cleaner. To give this the look of the originals that had a black paper exterior coating you can spray paint it flat black. If anyone knows of a source to buy the original paper coated foil tubes we would like to hear from you. Fits 1970 California Delivered Cars and all 1971 - 1973 Cars. Look for Buck Tag EV or EM. Preheat/Emission Control Duct.3ft long 7/8" O.D. 3/4" I.D. Replaces Ford Part #: D1UZ-9d667-A, D4HZ-9d667-A...

D3AZ-9D653-C Canister filled with charcoal or carbon particulates. Mounts in the rear side of the passenger side shock tower. *Note - These are 40 year old canisters, at this late stage the filtering ability of the particulates are probably not that effective for pollution testing. Primarily sold for concours judging.

D3DZ-9D664-A Bracket for mounting the charcoal canister to the body.

Ford called this part the fuel vapor separator. It mounts to the top of the fuel tank. This is part of the emissions control smog system, the fuel vapors that are collected in the charcoal canister are returned through a hose to this device into the fuel tank. Applications for this part include: 1971-73 Mercury Cougar and Ford Mustang, 1971-72 Pinto and Bobcat, 1971-72 Maverick and Comet, 1971 Thunderbird and Lincoln MKIII, and 1971-73 Ford / Mercury full sized cars. Starting about 1973, this...

Ford called this part the fuel vapor separator. It mounts to the top of the fuel tank. This is part of the emissions control smog system, the fuel vapors that are collected in the charcoal canister are returned through a hose to this device into the fuel tank. Applications for this part include: 1971-73 Mercury Cougar and Ford Mustang, 1971-72 Pinto and Bobcat, 1971-72 Maverick and Comet, 1971 Thunderbird and Lincoln MKIII, and 1971-73 Ford / Mercury full sized cars. Starting about 1973, this...

Used distributor modulator speedometer cable speed sensor for 1972 - 1973 Mercury Cougar and Ford Mustang. Mounts inline on a two piece speedometer cable. Ford master part number D2AF-9E731-A.

Used distributor modulator upper speedometer cable for 1971 - 1973 Mercury Cougar and Ford Mustang with the FMX or automatic transmission. Cable that connects the back of the speedometer and the speed sensor of the modulation system. Shown to be 10.54 inches long. 

Used wiring harness for the spark control box for the 1973 Mercury Cougar or Ford Mustang . This is only the harness, you can find the control box here.

Used control box for the spark control system on the 1973 Mercury Cougar or Ford Mustang. Ford part number D3AF9E447

D2ZZ-9A820-A Distributor modulator lower speedometer cable for 1972-73 Mercury Cougar and Ford Mustang. Shown to be 48 inches long.

Air cleaner pre-heater paper hose. Should fit most applications from 1970-73 Mercury Cougar and Ford Mustang with V8 engines. 2 inch inside diameter, we cut these to about 9 inches long. Correct black paper outside, flexible paper tube, kind of like a Slinky. Please verify your needed length, we leave them a bit longer than needed so that they fit more than one application.

Good used OEM original hood hinge set. Available individually or as a set. These are far superior to the off shore reproductions you see advertised everywhere. Fits 1971-73 Mercury Cougar and Ford Mustang. The reproductions are very difficult to make fit and do not last very long. We carefully inspect these hinges before sending them as used hinges are prone to wear in more than one area. Here is a helpful youtube video that shows you how to adjust your hood. Shipped with the springs.Ford...

Hood hinge spring for Mercury Cougar and Ford Mustang. Coil spring type with 6-1/4 inches of overall length. Sold individually, one per side. Ford part # D1ZZ-16789-A. *NOTE* Excludes 1971-73 Mustangs with ram air hood option.  

Good used OEM original passenger side hood hinge. Available individually or as a set. These are far superior to the off shore reproductions you see advertised everywhere. The reproductions are very difficult to make fit and do not last very long. We carefully inspect these hinges before sending them as used hinges are prone to wear in more than one area. It will be easier to fit and adjust the hinge prior to installing the spring on the hinge. Here is a helpful youtube video that shows you how...

Good used OEM original driver side hood hinge. Available individually or as a set. These are far superior to the off shore reproductions you see advertised everywhere. The reproductions are very difficult to make fit and do not last very long. We carefully inspect these hinges before sending them as used hinges are prone to wear in more than one area. It is easier to fit and adjust these hinges prior to installing the springs on them. Here is a helpful youtube video that shows you how to...

This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit of 50% of our web price for parts delivered in hand or by carrier to our Brooks, Oregon location. If you're not interested in store credit, just shoot us an email and we will let you know if it's is something we can pay cash for. We do not send cash for parts in advance but we often can compensate you within hours of receiving the...

Used door hinge anchor plate for attaching the door hinge to the body pillar. Driver side upper only, marked with an "L". Fits any 1971-73 Mercury Cougar and Ford Mustang.Ford part number D1ZZ-6502667-A.

Used door hinge anchor plate for attaching the door hinge to the body pillar. Driver side lower only, marked with an "L". Fits any 1971-73 Mercury Cougar and Ford Mustang.Ford part number C6OZ-6202639-A.

Used door hinge anchor plate for attaching the door hinge to the body pillar. Passenger side upper only, marked with an "R". Fits any 1971-73 Mercury Cougar and Ford Mustang.Ford part number D1ZZ-6502666-A.

Used door hinge anchor plate for attaching the door hinge to the body pillar. Passenger side lower only, marked with an "R". Fits any 1971-73 Mercury Cougar and Ford Mustang.Ford part number C6OZ-6202638-A.

Used upper rear fender brace that brace is visible when you open the door and look in the upper part of the fender void. Welds to the cowl on 1971-73 Mercury Cougar and Ford Mustang. Same tab either side. Ford part number D1ZZ-16A006-A.

Fuel tank spacer. Welds to the bottom side of the trunk pan. Spaces the tank, so that the fuel vapor separator assembly, isn't pinched. Easy to make these stands, and there are two needed, are approximately 1-1/2 inches tall. Strap is 1-1/8 inches wide.  

These are about half the weight of originals and do not look correct in any way. They are far better than nothing. Bolts to the left hand and right hand lower floor reinforcement panels. Bolts into place with 6 hex bolts 3/8-16 x 1-1/8" with washers. These were painted satin black from the factory. Replaces Ford Part # C5ZZ-7610962-A. The Ford description of this plate is "Plate - Front floor lower cross member". All 1969 - 1973 Cougar convertibles and all 1965 - 1973 Ford Mustang...

This 1965 Mustang alignment pin is not correct for the 1969 to 1973 Cougar but it will work. See the image to the left to see the comparison to an original 69 pin.

Usually ships in 3-5 business days. Replaces Ford Part #: C4DZ-7653337-A. This is a new part, not a rebuild, no core needed. Correct brackets for a Cougar, not a generic one size fits all application. 5 year warranty when used with automatic transmission fluid.

This is the storage bag that the convertible top cover folds into when the top is in the down position. Ford calls this part the "Folding top dust hood container." It is made from common vinyl top material and is always black. It measures 15"x27" and the bottom portion is sometimes, tapered down to 8". The same design was used for many Ford Products of the day including Torino, Montego and others. Current offering does not have a tapered bottom, it is square. Pictures will show both styles...

Reproduction Legendary Series GT5 Alloy Wheel. This updated design was created using state of the art casting technology for superior strength and precision. These wheels take a specific shouldered 3/4" lug nut, find them here. These wheels come with free chromed plastic center caps. The caps have a red Legendary logo but we can include at no cost, a set of black and chrome walking cat decals (click here). Just add it to your cart if you'd like these decals. If you want to upgrade to a premium...

This wheel is inspired by the 1966 Shelby GT350 10 spoke alloy wheel. This updated design was created using state of the art casting technology for superior strength and precision. Each wheel features a CNC machined face with natural aluminum accents and a clear coat finish. These wheels take a specific shouldered 3/4" lug nut, find them here. These wheels come with free chromed plastic center caps. The caps have a red Legendary logo but we can include at no cost, a set of black and chrome...

Reproduction clear coat natural finish aluminum alloy rim for the 1967 - 1973 Cougar or Mustang. Designed to look like the optional 10 spoke alloy wheel that was available on 67 - 68 Shelby GT350's ang GT 500's. These wheels come with free chromed plastic center caps. The caps have a red Legendary logo but we can include at no cost, a set of black and chrome walking cat decals (click here). Just add it to your cart if you'd like these decals. If you want to upgrade to a premium quality center...

Reproduction clear coat natural finish aluminum alloy rim for the 1967 - 1973 Cougar or Mustang. Designed to look like the optional 10 spoke alloy wheel that was available on 67 - 68 Shelby GT350's ang GT 500's. These wheels come with free chromed plastic center caps. The caps have a red Legendary logo but we can include at no cost, a set of black and chrome walking cat decals (click here). Just add it to your cart if you'd like these decals. If you want to upgrade to a premium quality center...