All Available Parts - 1972 Ford Mustang

Often you will see minor irregularities in these washers. These would be considered "blems". Two required per car, used only on the re-tractors.

Replaces Ford Part # 382626-S Sold individually

This fits behind the door panel and is needed to install your remote mirror correctly.*NOTE*1969 Cougar owners do not need this part as it is built in the the chromed plastic, rectangular bezel on the door panel.

Two or three of these clips were needed per door to mount the padded armrest. Three were used per car for a total of six, on 1969-70 Cougar and Mustangs. Two used in 1971-73 on standard Cougars. Sold individually.Replaces Ford part # C6AZ-6224146-B.

Reproduction shoulder belt bolt spacer for the 69 - 73 Cougar or Mustang. Does not have markings like the originals. One per side, two per car.

Used single bolt for attaching door and quarter window regulators on any 1969-73 Mercury Cougar or Ford Mustang or Ford anything most likely. Sold individually

New single bolt for attaching door and quarter window regulators on any 1969-73 Mercury Cougar or Ford Mustang or Ford anything most likely. AMK part. Sold individually

Reproduction bolts and washers for the shoulder belts on any 1969-73 Mercury Cougar or Ford Mustang. Includes 2 each of the "D" bolts and chrome thick washers. Quality AMK kit F-3563.

AMK seat belt washer B-13023. 0.46" ID x 1.25" OD zinc flat washer. Sized so that it rides on the shoulder of the seat belt bolts. It allows the retractor to rotate freely between this washer and the head of the seat belt bolt on 1969-73 cars. Two required per car, used only on the re-tractors.

Phosphate & Oil finish. Sold individually. Replaces Ford part #: 378782-S

This is longer of the two with the + on the bolt head.

part# 372821-S

Ford manual transmission flywheel and automatic transmission flex plate mounting bolts. 6 bolts required, sold individually. Replaces Ford part # 378172-S

Replaces Ford part # 55806-S

part # 56131-S

Used on all small block engines to attach the timing pointer to the timing cover. 1967 - 1973 V-8 engines 289, 302, & 351. Sold individually

Reproduction AC Compressor Clutch Bolt for the 1967 - 1973 Mercury Cougar - 1967 - 1973 Ford MustangSold individually

Reproduction 351W Intake Manifold Bolt for the 1969 - 1973 Mercury Cougar - 1969 - 1973 Ford MustangSold individually 

Reproduction Alternator Pulley Nut for the 1967 - 1973 Mercury Cougar - 1967 - 1973 Ford MustangSold individually 

Replaces Ford part # 351089-S Zinc (dark silver) finish Sold individually

Reproduction of the plastic square hood insulation clips. 11 used on most vehicles. Sold individually.

replaces Ford part # 385161-S Zinc - Dichromate (yellow - rainbow) finish

Bolts and installation kit for most 1970-73 Mercury Cougar and Ford anything, including Mustang with V-8 engines. Kit includes main pivot bolt and adjusting bolt as shown. Spacer not included, but available used.

Used bolt and washer from a factory installed AC Compressor 1967 - 1973 Mercury Cougar - 1967 - 1973 Ford Mustang. Attaches clutch to compressor shaft.

Replaces Part # C9OB-3B284. We also have this bolt available in fine thread but only as a used bolt. Four required per car. Sold individually

part # 370608-S. Used in multiple places on mounting brackets.

This nut fits onto the strut brace at the front of the car, and not the control arm end.Replaces Ford part # 380517-S

part # 383722-S Pivot bolt for use with the all steel 1970-73 power steering pump mounting bracket. NOS new old stock! Fits most all Ford 302/351 from 1970-73 with the above described bracket.

OEM style nut to hold the axle U-bolt to the axle. Fine threaded like originals 7/16-20 grade 5. Will not fit some reproduction U-bolts. Sometimes these are called shock plate bolts. Replaces Ford part # 379244-S

part# 384114-S100 Sold individually Check out this video

Reproduction adjustment cam / bolt for the lower control arms of the Mercury Cougar or Ford Mustang. We also offer this used version as well. These units are sold individually.Ford part # C6OA-3B236-A.

1/2"-13 x 4 1/2" grade 8 flanged bolt with a phosphate and oil finish.  Ford Part # 382486-S.

replaces Ford part # B-12764

Replaces Ford part #375381-S Phosphate & Oil Finish

Fine thread lock nut used in various places on old Fords, including the differential housing, 1967 disc brake assemblies, and more. Replaces Ford part # 34445-S

Reproduction nut that replaces Ford part # 34033-S. This is the nut that secures the pitman arm to the steering box. Has correct 7/8"-14 threads. Split washer also needed, not included, nut only.

Reproduction disc brake hose bolt for any 1968-73 Mercury Cougar and generally all other Ford cars with factory disc brakes. Special hollow bolt with cross drilled hole. Attaches the high pressure hose to the caliper.

Fits both 8 inch and 9 inch rear ends. Phosphate and oil coated with thread sealer. These are one time only nuts. They should not be reused per Ford. Replaces Ford part #: 371518-S

Hard to find driver side regulator

Good used original regulator. Ford Part #: D1ZZ-6523208-B

Reproduction power window motor for the passenger side (right hand) door glass of the Mercury Cougar or Ford Mustang equipped with power windows. This unit is for the 69-73 Mercury Cougar, but only years 1971-73 for the Mustang. This is the same motor that found it's way into most all other Ford/Lincoln/Mercury cars in that year range as well. If you need the rear pancake style motor, you can find that here. *NOTE*  This is the only version of the power window motor that is available at...

Reproduction power window motor for the driver side (left hand) door glass of the Mercury Cougar or Ford Mustang equipped with power windows. This unit is for the 69-73 Mercury Cougar, but only years 1971-73 for the Mustang. This is the same motor that found it's way into most all other Ford/Lincoln/Mercury cars in that year range as well. If you need the rear pancake style motor, you can find that here.*NOTE* This is the only version of the power window motor that is available at the moment....

Nice reproduction oil dipstick made from all stainless steel. Only fits 289 or 302 Ford engines from 1967-73. These dipstick tubes have the 'full' and 'add' markings in the correct place, however they do not have any Ford part numbers stamped on them. Black steel as shown, not plain shiny steel like originals.Replaces Ford part # C7OE-6750-B or C8OE-6750-B.

Nice reproduction oil dipstick made from all steel, painted Ford engine blue. Only fits 289 or 302 Ford engines from 1967-73. These dipstick tubes have the 'full' and 'add' markings in the correct place, however they do not have any Ford part numbers stamped on them. Black steel as shown, not plain shiny steel like originals. Replaces Ford part # C7OE-6750-B or C8OE-6750-B.

Engine oil dipstick as found on most any 1970-73 Ford with 351 Cleveland engines (H, or M Code), 1972-73 (Q code). Ford used several different suppliers and there are differences that show up in the finger handle as shown. Top of the shield to the dipstick end is approximately 21-11/16 inches. The handles were painted blue originally. Ford part # D0AZ-6750-A, Ford casting # D0AE-6750-A.*NOTE* In 1970 351W engines also were designated as H codes, 351W has 6 bolts attaching the valve covers,...

Brightens the engine compartment and looks sharp. Fits aftermarket valve covers only. These require a rubber grommet to fit into the valve cover. Please Note: This oil cap DOES NOT fit the finned "G" valve covers we sale, as they are built to OEM specs.

Used 1970-72 black AUTOLITE marked oil fill cap with black plastic elbow. Several variations noted from our collection, AUTOLITE and MOTORCRAFT versions. Will need detailing or fresh black paint applied. Would also suggest replacing the rubber grommet. These 50 year old rubber grommets are rock hard and likely leak air. Gasket to valve cover will also need replacement. Even though this cap has a 1971 parts number, we see these on the 1970 351C engines quite often. Replaces Ford part...

SBVALVCOVER Ford engine blue painted valve cover with "Powered by Ford" embossed in the metal. Correct on 1968-1971 Mercury Cougar and 1968-73 Ford Mustang with 289/302/351W engines. Ford master parts catalog shows a right and left version of this cover those Service Replacement numbers are D2OZ-6582-C & D2OZ-6582-D. *Note - This cover will not work on a 351 Cleveland engine.

351C VALVCOVER Ford engine blue painted valve cover with "Powered by Ford" embossed in the metal. Correct on 1970-1973 Mercury Cougar and Ford Mustang with 351C engines. Ford master parts catalog shows a right and left version of this cover those Service Replacement numbers are D2SZ-6582-A & D2SZ-6582-B. Although we have more of these in inventory, we do not recommend them because the remaining quantities will be less than desireable. *Note - This cover will not work on a 351 Windsor engine. ...

Fits 1967 - 1973 Standard or XR7. Pins not used on 71-73 buckets.

Fits 1967 - 1973 Standard or XR7

Secures cable to heater control assembly, heater plenum and heater box. Black oxide bracket with screw.Replaces Ford part number 378897-S

Fits 1968 - 1973 Standard or XR7

Holds insulation to the firewall. Sold individually, 6 per car. Replaces Ford part # C8ZZ-6501691.

This is the rubber spacer / washer that goes between the bolt head and the metal washer of your seat belt hardware. The purpose of the rubber washer is to dampen any vibrations caused by the movement of the seat belt.Sold individually# 354959-S

Sold individually # 374212-S

Concours correct for 67, but a nice dress-up item for 68-73. Replaces Ford Part # 382627 Four bolts, four washers and eight rubber washers in mounting kit.

For 1972-73 Mercury Cougars and Ford Mustangs with the 351W engine. This is a Pitts manufactured pulley and clutch assembly with a pulley diameter of 6-5/16", a clutch diameter of 5-1/8", and an overall thickness of 1-11/16 inches. Whew boy, say that 5 times fast!Ford part # D2ZA-2981-A. May also have part numbers of D2ZA-2981-A1A, D2ZA-2981-A1B, or D2ZA-2981-A2A.

Brake line rubber grommets for any 1967-73 Mercury Cougar or Ford Mustang. These are the ones that go through the shock towers for the front brake lines. Drum or disc, all the same. Sold as a PAIR. Ford number 373624-S.

Used bolts, and usually new washers. Convertible kit comes with 4 - "A" bolts, 4 "B" bolts, 10 new washers. Kit fits all 1970-73 Mercury Cougar and Ford Mustang convertibles. Coupes or hard tops would include shoulder belt hardware. We will make sure these original seat belt bolts are damage free and rust free. The gold finish will be degraded. There were minor and major changes almost every year. We also have hundreds of used belts and belt sets that we cannot possibly list all of, so give us...

384543-S8 Power steering pump adjusting spacer for use without air conditioning. For most 1970 - 1973 Mercury Cougar or Ford Mustang with 351C engines. Spacer dimensions: 7/16" I.D. and 1/2" thick.*Note 1970 and later cars with 302 or 351W engines use a 3/4 inch spacer.

These are sold individually, two required per car. This is the aluminum emblem / decal which mounts on the center of some late 67 and all 68-73 scuff plates. Features raised script like original. Adhesive backed with a protective coating that peels off after installation. Replaces Ford Part #: C7ZZ-6513208-T. Licensed by FORD ...

Concours? Well almost... These are stainless steel screws with the wax tipped coating like the originals, for installing the door sill plates. The wax was deemed necessary by the Ford Motor Co. as a seal. These can be used on all years 1967-73 Mercury Cougar, Ford Mustang and most all other Ford, Mercury, Lincoln cars of the era. Works well with any of the reproduction sill plates, these were really made to be used with the premium reproduction sill plates in stainless steel. 1967-68...

Good quality but not as good as original in that it is too shiny. Fits Coupe or convertible, left or right. Sold individually. Ford emblem sold separate. Replaces Ford part # D1ZZ-6513298-A

Good deal for the guy missing a sill plate on a driver. Sold individually.

Reproduction stainless steel scuff / sill plate. Fits Coupe or convertible, left or right. Sold as a pair. Ford emblem sold separate, find it here. Replaces Ford part # D1ZZ-6513298-A

Concours? almost, these are stainless steel screws with the wax tipped coating like the originals, for installing the door sill plates. The wax was deemed necessary by the Ford Motor Co. as a seal. These can be used on all years 1967-73 Mercury Cougar, Ford Mustang and most all other Ford, Mercury, Lincoln cars of the era. Works well with any of the reproduction sill plates, these were really made to be used with the premium reproduction sill plates in stainless steel. 1967-68 Cougar and...

Door striker replacement bushing.   .90 tall, .69 OD. .49ID. .10 thickness. These plastic bushings were used starting in 1972. We also sell the whole striker assembly. Common striker to many Ford cars after 1971. Apparently Sikorski helicopters too.

Door Striker bolt assembly complete with PVC bushing. 7/16-14 thread. Silver zinc finish. Replaces Ford part #: D2AZ-6522008-A.

Plastic insert with metal locking retainer. Replaces Ford part # C5AZ-6221952-A. NOTE* This clip will need to be squeezed on the clip side in order to obtain a good grip. Check out our handy diagram below to find other '67-'68 door parts you may need. All the item numbers shown can be typed in to the search bar on our site. (Click image to view full size) ...

Replaces Ford Part #: D1ZZ-6221813-A

Replaces Ford Part #: D1ZZ-6221812-A

Convenient matched sets save costly locksmith work. Kits includes a pair of door lock cylinders. Comes with two keys. Includes door cylinder gaskets. If you don't mind have having a different key for the door locks, this product might just work out.Attention potential buyer! This item will likely give you problems and be a general disappointment. Reviews show that the fitment is fair, and you will not be able to have these lock cylinders re-pinned, to use your original Ford key. One...

Ignition lock set is new original from the O.E.M. source. Factory fresh with two keys. Fits 1970 through 1973's manufactured before 5/17/1973. Replaces Ford Part #: D0AZ-11572-A, D2AZ-11582-B, SW-1114.

These are the screws that secure the door latch mechanism to the door shell. These screws come with the attached crown headed lock washer, just like the originals, so be sure to tighten them down snugly to ensure that the screw head sits flush into the screw holes. Sold individually. Three required per door, six per car.

Door lock latch lever, for driver or passenger side locks. Attach with an "E" clip on the rear side of the lock mechanism. Used "E" clip is included. We are going to say that these fit all Ford door locks 1965 through 1973 and beyond. *Note you will need to purchase or reuse your retainer clip for attaching the lock rod. Retainer clip not included, we have good used or reproduction clips, see related items.Ford number stamped C5AB-6221970-A or D2AB-6221970-AA  ...

Latch rod that links the door latch and the inside door handle, passenger side door. Fits any 1971-73 Mercury Cougar and Ford Mustang. Normally this rod was fabric covered. Used rod only, no retaining end clips.Replaces Ford part number D1ZZ-6521940-A.

Latch rod that links the door latch and the inside door handle, driver side door. Fits any 1971-73 Mercury Cougar and Ford Mustang. Normally this rod was fabric covered. Used rod only, no retaining end clips.Replaces Ford part number D1ZZ-6521941-A.

Inside door handle release mechanism for the driver side on 1972-73 Cougar and Mustang. This latch mechanism went through a couple of revisions by the end of 1973. Ford calls this part a 'control and link assembly', this particular one only works with the deluxe door handles as shown in the photo. The Ford MPC describes those door handles as fitting the door panels with molded armrests, instead of the smaller detachable armrests on the base interiors. This style was used after 9/15/1971. It...

Inside door handle release mechanism for the passenger side on base model standard 1972-73 Cougar and Mustang. This latch mechanism went through a couple of revisions by the end of 1973. Ford calls this part a 'control and link assembly', this particular one only works with the base door handles as shown in the photo. The Ford MPC describes those door handles as fitting the door panels with detachable arm rests, instead of the molded arm rests on the door panels, as found on the XR7 and Decor...

Inside door handle release mechanism for the passenger side on 1972-73 Cougar and Mustang. This latch mechanism went through a couple of revisions by the end of 1973. Ford calls this part a 'control and link assembly', this particular one only works with the deluxe door handles as shown in the photo. The Ford MPC describes those door handles as fitting the door panels with molded armrests, instead of the smaller detachable armrests on the base interiors. This style was used after 9/15/1971. It...

Reproduction passenger side (right hand) tinted door glass for the Mercury Cougar or Ford Mustang coupe or convertible equipped with power windows. There are three versions of this glass. The clear version is just that

Reproduction driver side (left hand) tinted door glass for the Mercury Cougar or Ford Mustang coupe or convertible equipped with manually operated windows. There are three versions of this glass. The clear version is just that

Reproduction passenger side (right hand) tinted door glass for the Mercury Cougar or Ford Mustang coupe or convertible equipped with manually operated windows. There are three versions of this glass. The clear version is just that

Reproduction driver side (left hand) clear door glass for the Mercury Cougar or Ford Mustang coupe or convertible equipped with manually operated windows. There are three versions of this glass. The clear version is just that

Reproduction passenger side (right hand) clear door glass for the Mercury Cougar or Ford Mustang coupe or convertible equipped with manually operated windows. There are three versions of this glass. The clear version is just that

Reproduction driver side (left hand) clear door glass for the Mercury Cougar or Ford Mustang coupe or convertible equipped with power windows. There are three versions of this glass. The clear version is just that

Reproduction driver side (left hand) tinted door glass for the Mercury Cougar or Ford Mustang coupe or convertible equipped with power windows. There are three versions of this glass. The clear version is just that, clear with no tint. There is a tinted version that will have a slight green tint to the glass, SUN-X factory tint. There is also a second tinted version that is called smoked and this version has a grey / brown tint to the glass. The clear and the tinted versions are reproductions...

Reproduction power window conversion for your Cougar or Mustang. These kits are easy to install and bolt into the original mounting holes, and use your existing window channels. Once you install the kit, your window crank becomes the switch. Simply lift up on the crank to roll the window up, and press down on the crank to roll the window down. Made from quality materials like 1018 cold rolled steel, Oilite thrust bearings at the pivot points and treated metal for all the gears makes for a high...

Reproduction power window conversion for your Cougar or Mustang. These kits are easy to install and bolt into the original mounting holes, and use your existing window channels. Once you install the kit, your window crank becomes the switch. Simply lift up on the crank to roll the window up, and press down on the crank to roll the window down. Made from quality materials like 1018 cold rolled steel, Oilite thrust bearings at the pivot points and treated metal for all the gears makes for a high...

Complete six piece window glass set for the 1971

Reproduction six piece SUN-X or tinted glass set for the Mercury Cougar coupe equipped with or without power windows. This set does not come with any of the window trim so save yours for reuse. There are three versions of this glass. The clear version is just that

Reproduction CLEAR five piece glass set for the 1971-73 Mercury Cougar coupe or Ford Mustang hard top equipped with power or crank windows. This set does not include any of the window trim so save yours for reuse. There are three versions of this glass. The clear version is just that

Reproduction TINTED five piece glass set for the Mercury Cougar coupe equipped with either power windows or crank windows. This set does not include any of the window trim so save yours for reuse. There are three versions of this glass. The clear version is just that

Reproduction six piece extra dark tinted glass set for the Mercury Cougar coupe with manual windows. This set does not come with any of the window trim so save yours for reuse.

Four piece CLEAR window glass set for the 1971

Complete five piece window glass set for the 1971

Reproduction tinted four piece glass set for the Mercury Cougar or Ford Mustang convertible equipped with manually operated windows. This set does not include any window trim so save your for reuse. There are three versions of this glass. The clear version is just that