1973 Mercury Cougar

High quality and correct looking air conditioning discharge hose for Mercury Cougars or Ford Mustangs. This hose is compatible with both 134a and R12 refrigerants.

Regardless of which V-8 engine, D1ZA-19972-AA or D1ZA-19972-AB part number. This hose is approximately 24 inches long. These used hoses probably still hold pressure, we suggest a purchase of new 'O' rings prior to installation.

For Mercury Cougar and Ford Mustangs with integral or factory installed air conditioning with any V-8 engine. Original condensation drain hose from the A/C case, through the floor board, to the ground. Correct "S" shaped moulded hose with restrictor intact. Almost the same hose as was used 1969-70, Dearborn assembly line hoses have a ribbed section 1971-73. The 1969-70 versions, typically have the alligator texture on the outside of the hose.  Ford part # C9ZZ-19858. ...

Click on images to enlarge. Includes Sight Glass Hose (Ford Part # D1ZA-19837-A), the sight glass (Part # SG3, D2AZ-19D695-BK or YF-342). One of the major differences between the reproduction and the original sight glass hoses, is that the texture of the originals was much more defined.  You can see and feel the ridges in the hose on the originals.  Below is a close up picture of repro and used side by side, and it is obvious that the repro is not nearly as textured as the originals...

Good used hose that connects the sight glass hose to the Air Conditioning Dryer.

Regardless of which V-8 engine, D1ZA-19867-BC part number. This hose is approximately 49 inches long.

This is actually a kit which includes 2 hoses (Part # D1ZA-19835-A and Part # D1ZA-19837-A), the sight glass (Part # SG3, D2AZ-19D695-BK or YF-342), 2 o-rings (Part # L33,D2AZ-19D695-R or YF-368 and Part # H33, D2AZ-19D695-AE or YF-316) and a quick connect (Part # QF3,C1SZ-19B696-A or YF-241 and Part # QM6, C1SZ-19B695-A or YF-252). *Note we normally supply the new coupler with this kit. Regardless of which V-8 engine, this hose when assembled is approximately 78 inches long.Ford MPC kit #...

For 1972-73 Mercury Cougars and Ford Mustangs with the 351W engine. This is a Pitts manufactured pulley and clutch assembly with a pulley diameter of 6-5/16", a clutch diameter of 5-1/8", and an overall thickness of 1-11/16 inches. Whew boy, say that 5 times fast!Ford part # D2ZA-2981-A. May also have part numbers of D2ZA-2981-A1A, D2ZA-2981-A1B, or D2ZA-2981-A2A.

Reproduction A/C Tag Retainer for the 1967 - 1973 Mercury Cougar

This A/C vacuum canister mounts to the passenger side shock tower and controls damper doors inside the A/C unit. This unit includes a built in check valve. Used and tested vacuum tank and bracket, also known as the A/C vacuum reservoir. Fits all 1971-73 Mercury Cougar, 1971-73 Ford Mustang, as well as 1970-71 Ford Torino / Fairlane and Mercury Cyclone Montego, 1970-7? Ford Maverick and Mercury Comet.Replaces Ford part # D0DZ-19A566-A.  

part # 370608-S. Used in multiple places on mounting brackets.

This decal was available in both red and purple and both decals have the same Ford part number on them with the purple decal being slightly larger with more defined text. This is the purple version.Decal reads:Ford Dearborn, Mich. Air Conditioner Maximum Operating Charge 4LBS. 8OZ. of R-12 Complies With SAE-J639 Replaces part # D20E-19A688-AB