All Available Parts - 1972 Mercury Cougar

This is the stainless steel, two prong version fuel sending unit for 71 - 73 Cougars and Mustangs. The reason for the two prong, is that this particular year used a ground wire coming off of the sending unit. Cougars equipped with the convenience control package, and the XR7's used a three prong version. These units are better than original being made from stainless. The function however is not as good as original but adequate and usually will work for years. If you have an original, often...

Exclusive to WCCC, here's our reproduction in-tank, fuel sending unit with the low fuel option. Good for all 1971 - 1973 Mercury Cougar XR7's and all Ford Mustangs with 16 gallon fuel tanks. This is a reproduction of a 1971 fuel sending unit with three prongs (2 electrical and 1 alignment prong). The original Ford casting number was D1WF-9275-AC. This unit comes with a new 3/8 inch filter, brass float, and sending unit gasket. These are completely interchangeable on all 1971 - 1973 20 gallon...

Often when your fuel gauge is acting up, this is the culprit, not the gauge or sending unit. The benefit of using this foam float, is that sometimes the hollow brass float will leak, causing a bad reading. This foam version of the float is fuel resistant and will never leak. Replaces Ford part #C0AZ-9202-B.Check out the video below on our new gauge tester: ...

Yes, we can rebuild other than 1967-73 Mercury Cougar and Ford Mustang sending units. 1967-1980 Ford / Mercury / Lincoln sending units accepted. See our related listing for non-low fuel sending unit rebuilding. Your core must be complete and not overly corroded. We are unable to convert from non-low fuel to low fuel. We also cannot change plugs for different years. We do not repair rust or rust through holes. We do not have critical or specific spare parts for rebuilding....

This option requires that you send your core in advance. Your core gets rebuilt and returned. If you don't have a core, WCCC has come across a few from our wrecking yard, give us a call to discuss details. Our service is to rebuild your standard fuel sending unit. A quality core is required. Yes, we can rebuild other than 1967-73 Mercury Cougar and Ford Mustang sending units. 1967-1980 Ford sending units accepted. See our related listing for low fuel sending unit rebuilding. A quality...

Used retaining ring for the fuel sending unit or vent on 1971 and newer tanks. Fits a little tighter than the reproduction rings. Ford part #C0AZ-9A307-B.

Used switch panel for most 1971-73 XR7 hard tops. Panel holds 3 different toggle switches: COURTESY - MAP - ACCY. All came painted black with the camera case finish with the indicated switches as shown. Most will be nearly pit free as shown but will need a spray of black paint for that 'extra' detail prior to installation.*Note excludes convertible and those Cougars with the heated back lite or rear defog option.Replaces Ford part number D1WY-6504338-A.

Used switch panel for most 1971-73 XR7 hard tops. Panel holds 3 different toggle switches: COURTESY - MAP - R.DEFOG. All came painted black with the camera case finish with the indicated switches as shown. Most will be nearly pit free as shown but will need a spray of black paint for that 'extra' detail prior to installation. This panel does have a small hole above the defog switch for the red indicator light. Red indicator light sold separately. *Note excludes convertible and those Cougars...

Used switch panel for most 1971-73 XR7 convertibles. Panel holds 3 different toggle switches: COURTESY - MAP - TOP. All came painted black with the camera case finish with the indicated switches as shown. Most will be nearly pit free as shown but will need a spray of black paint for that 'extra' detail prior to installation.  *Note excludes all coupe or hard top Cougars, and non-XR7 convertibles.Replaces Ford part number D1WY-7604338-A.

Used clear lens for the Oil & Amp gauge cluster found on all 1971-73 Mercury Cougar XR7's. We offer these as replacements, often the UV rays damage the ones on convertibles.Check out the video below on our new gauge tester: ...

This trim ring that surrounds the glove box release button is often missing. Easily installs by snapping in place. Better fit than the reproductions out there.Replaces Ford part number C6OB-62060A12.

Used cigar or cigarette lighter bezel for 1971-73 Mercury Cougar and Ford Mustang. Ford part # D1ZZ-15052-A and D1ZB-15053-A

Used wiper switch bezel for any 1971-73 Mercury Cougar and Ford Mustang. Good used bezel with shiny chrome. May have one small nick in the chrome or one broken plastic stud on the reverse.Replaces Ford part number D1ZB-17C564-AC.

Used headlight switch bezel for any 1971-73 Mercury Cougar and Ford Mustang. Good used bezel with shiny chrome. May have one small nick in the chrome or one broken plastic stud on the reverse.Replaces Ford part number D1ZB-11649-AC.

Used steel rear retaining bracket for the windshield wiper switch and cigar lighter on any 1971-73 Mercury Cougar or Ford Mustang. These are bare steel and will have a bit of flash rust as shown, nothing serious. Replaces Ford part number D1ZB-17C584-AC.

Used steel rear retaining bracket for the headlight switch on any 1971-73 Mercury Cougar or Ford Mustang. These are bare steel and will have a bit of flash rust as shown, nothing serious. Replaces Ford part number D1ZB-13B107-AC.

Used bezel retaining nut for the headlight switch on any 1971-73 Mercury Cougar or 1971-72Ford Mustang. These are much better quality than those found in the 1969-70 cars. Good threads and very good chrome on the front as shown. Check the length for the 1973 Ford Mustang, we've had an owner that found one to be over 2 inches in length. Unfortunately, we do not have the longer length version.Replaces Ford part number D1ZB-11650-BA.

Used bezel retaining nut for the windshield wiper switch on any 1971-73 Mercury Cougar or Ford Mustang. Good threads and very good chrome on the front as shown. Replaces Ford part number D1ZB-17512-A.

Reproduction cigar / cigarette lighter for the 71 - 73 Cougar.

Reproduction wiper switch bezel for the 71 - 73 Cougar and Mustang. Replaces Ford part number D1ZB-17C564-AC.

Reproduction headlight switch bezel for any 1971-73 Mercury Cougar and Ford Mustang.  Replaces Ford part number D1ZB-11649-AC.

Carburetor gasket for all 1972 Mercury Cougar and Ford Mustang with 351C-2V engines. This is a new gasket meant for use with stock Ford intake manifolds and correct Autolite/Motorcraft 2100 carburetors. Single gasket as shown, if you have a carburetor spacer plate you would need two gaskets.

C7WB-13753-A Grade-A used screw on nut or bezel for the dash toggle switches on 1967-68 Mercury Cougar XR-7, 1971-73 Mercury Cougar, and 1969-70 Mustang Shelby console switches. This is a perfect used part, if you need an average quality used one mention it when you make your order and we will try and locate a free one for you.

Cigar or cigarette lighter for 1971-73 Mercury Cougar and Ford Mustang. Slight change from the 1970 style, this one has a black plastic shaft. Ford part # D1ZZ-15052-A.

This actually is a pretty impressive part once installed. It fits snug (very tight) over your existing cracked dash and you affix it by putting silicone around the perimeter. Unlike the 67-70 there is no stitched edge or speaker holes in the 71-3 so it is a perfect candidate for this cover. The good thing about this unit is that your dash pad can have large chunks missing and it still will work! You can install this without removing the dash and it is very hard to detect once in place. Made of...

Good used textured steel dash panel, for all 1971-73 Mercury Cougar and Ford Mustang. This is the flat steel piece that the meets the windshield and houses the defroster nozzles for the windshield.  Attaches to the dash pad using (5) 45271-S36 nuts.*Note - Save your VIN tag from your original dash, you don't want to lose it.Replaces Ford part number D1ZZ-65044D90-A. ...

This clip attaches to the textured steel dash top on many 1971-73 Ford, Mercury, and Lincoln cars. Mostly full sized and intermediate cars such as Cougar, Mustang, Torino, Cyclone, Montego, Ranchero, Lincoln, and Continental. 3 of these clips are used to attach the dash top panel to the cowl at the windshield. Sold individually.The curved tail kind of guides the panel into the slot at the front. The illustration for this part is shown on page 48 of the 1971-72 Mustang Body Assembly Manual....

Used hinge for any 1971-73 Mercury Cougar or Ford Mustang. Comes as shown, we select the best hinges to inventory.Replaces Ford part number D1ZZ-6506050-A.

Used door / lid for the glove box in the Mercury Cougar, grade "B". This is just the bare inner and outer door / lid and does not come with the hinge, liner, lock or lock bezel. To prevent damage to the plastic glove box door, the inner steel backer should be removed and file 1/16" off of one or both sides. Cracking is due to shrinkage of the plastic glove box door over time.Plan on painting to match your interior. Ford part # D1WY-6506024-A for the inner, D1WY-6506024-B for the outer. ...

Used door / lid for the glove box in the Mercury Cougar, grade "B", with at least one crack, or an extra chip or scrape. This is just the bare inner and outer door / lid and does not come with the hinge, liner, lock or lock bezel. To prevent damage to the plastic glove box door, the inner steel backer should be removed and file 1/16" off of one or both sides. Cracking is due to shrinkage of the plastic glove box door over time.Plan on painting to match your interior. Ford part # D1WY-6506024-A...

Used door / lid for the glove box in the Mercury Cougar, grade "A". This is just the bare inner and outer door / lid and does not come with the hinge, liner, lock or lock bezel. To prevent damage to the plastic glove box door, the inner steel backer should be removed and file 1/16" off of one or both sides. Cracking is due to shrinkage of the plastic glove box door over time. Standard model Cougar, not for XR7.Plan on painting to match your interior. Ford part # D1WY-6506024-A for the inner,...

Used glove box catch for any 1969-73 Mercury Cougar or Ford Mustang. Ford part number C9AZ-6206064-A.

Used glove compartment lock latch without a key. Fits many Ford cars 1969-73 including Mercury Cougar and Ford Mustang. Mustangs normally did not have lockable glove boxes, but this will still work. These are stamped with a key code, and a key could be cut if you wanted a working lock. See related items for matching trunk and glove box locks with key. Part of the Ford part number 22050 keyed lock sets. No hardware or fasteners included.

These original clips hold better than the reproductions we offer. If you look closely you will see the angle bend is more acute on the originals. For you 71-73 owners with warped panels you will want to use these original clips (at least along the bottom edge) for a tighter hold. The only difference between this spring clip and the other used one we offer is the presence of the foam spacer pad. Helpful tip: Door panel clips install sliding toward the rear of the vehicle. ...

In addition to fastening your door panels to the doors, these spring clips are also used to fasten your pads to the console on 67 - 68 models and seat backs to seats 67 - 70. Coated to prevent rust. Sold Individually. These do not hold as well as our originals but do function fine for most applications. 23 - 29 used per door panel, depending upon model. Helpful tip: Door panel clips install sliding toward the rear of the vehicle. ...

Package of 30 spring clips. These are also used to fasten your pads to the console on 1967-68 Models. Coated to prevent rust. 23 - 29 used per door panel, depending upon model. Helpful tip: Door panel clips install sliding toward the rear of the vehicle.

Sold as a pair, call for color and exact description as this is just a sample of what you can expect with grade "B" panels. Will have multiple small defects but can be cleaned up and used for a driver. Unlike the XR7 or decor (deluxe) panels the standard panel can be identified by its removable arm rests.NOTE: The pictures shown here are file photos from sets we have sold in the past and are not the actual panels or color you will receive. Please email or call for current colors and conditions...

Complete four piece door vapor barrier kit specifically cut for the year of your Cougar. Check out the video on replacing your door panels below.

Complete four piece door vapor barrier kit specifically cut for the year of your Cougar. Check out the video on replacing your door panels below.

We cannot enthusiastically recommend these plastic covers. Actually... they are just plain garbage! The problem with covering your cracked door panels is that often cracked panels are badly warped at the bottom which makes it difficult to make these rigid covers fit right. These will not take paint nearly as well as our soft vinyl covered reproduction door panels. The challenge with using our XR7 repro panels on your decor equipped Cougar is that you will need to buy used round walking cat...

We cannot enthusiastically recommend these plastic covers. Actually... they are just plain garbage! The problem with covering your cracked door panels is that often cracked panels are badly warped at the bottom which makes it difficult to make these rigid covers fit right. These will not take paint nearly as well as our soft vinyl covered reproduction door panels. The challenge with using our XR7 repro panels on your decor equipped Cougar is that you will need to buy used round walking cat...

We cannot enthusiastically recommend these plastic covers. Actually... they are just plain garbage! The problem with covering your cracked door panels is that often cracked panels are badly warped at the bottom which makes it difficult to make these rigid covers fit right. These will not take paint nearly as well as our soft vinyl covered reproduction door panels. The challenge with using our XR7 repro panels on your decor equipped Cougar is that you will need to buy used round walking cat...

We cannot enthusiastically recommend these plastic covers. Actually... they are just plain garbage! The problem with covering your cracked door panels is that often cracked panels are badly warped at the bottom which makes it difficult to make these rigid covers fit right. These will not take paint nearly as well as our soft vinyl covered reproduction door panels. The challenge with using our XR7 repro panels on your decor equipped Cougar is that you will need to buy used round walking cat...

Used interior door panel chrome moulding for the driver side of any 1971-73 Mercury Cougar with either Decor or XR7 interiors. Original die cast chromed mouldings, these clean up very well with 0000 steel wool. Minor pitting if any at all on these used mouldings. These attach to reproduction or used door panels by bending over the metal tabs on the back. Nearly all of our selected used mouldings will have one or two places where the metal tabs are coming loose. There are so many of them, that...

Used interior door panel chrome moulding for the passenger side of any 1971-73 Mercury Cougar with either Decor or XR7 interiors. Original die cast chromed mouldings, these clean up very well with 0000 steel wool. Minor pitting if any at all on these used mouldings. These attach to reproduction or used door panels by bending over the metal tabs on the back. Nearly all of our selected used mouldings will have one or two places where the metal tabs are coming loose. There are so many of them,...

Grade A door cup (escutcheon) used on both the Xr7 and Decor / Deluxe interiors with moulded door panels. Casting numbers as seen on the back can read D1WB-6522635-A or D3WB-6522635-A. The last 3 digits will read something like -AWA, AWD or similar which denotes the different colors. These resemble Mustang but are in fact unique to the Cougar. Very hard to come by without substantial UV damage. Please denote interior color and we will attempt to send your requested color. Product Condition...

Used on both the Xr7 and Decor / Deluxe interiors with moulded door panels.

Grade B door cup (escutcheon) used on both the Xr7 and Decor / Deluxe interiors with moulded door panels. Casting numbers as seen on the back can read D1WB-6522635-A or D3WB-6522635-A. The last 3 digits will read something like -AWA, AWD or similar which denotes the different colors. These resemble Mustang but are in fact unique to the Cougar.  Grade B versions will have significant UV damage and will need to be cleaned as best possible and painted. Plastic will be flakey and may be...

Grade B door cup (escutcheon) used on both the Xr7 and Decor / Deluxe interiors with moulded door panels. Casting numbers as seen on the back can read D1WB-6522635-A or D3WB-6522635-A. The last 3 digits will read something like -AWA, AWD or similar which denotes the different colors. These resemble Mustang but are in fact unique to the Cougar. Grade B versions will have significant UV damage and will need to be cleaned as best possible and painted. Plastic will be flakey and may be be...

Package of 100 spring clips. These are also used to fasten your pads to the console on 1967-68 Models. Coated to prevent rust. 23 - 29 used per door panel, depending upon model. Helpful tip: Door panel clips install sliding toward the rear of the vehicle.

Correct texture and molded-in colors, with steel insert molded into foam to increase strength. Extra thick vinyl skins. American made. Replaces Ford part # D1ZZ-6524101.

Correct texture and molded-in colors, with steel insert molded into foam to increase strength. Extra thick vinyl skins. American made.

Correct texture and molded-in colors, with steel insert molded into foam to increase strength. Extra thick vinyl skins. American made. Replaces Ford part # D1ZZ-6524100.

Correct texture and molded-in colors, with steel insert molded into foam to increase strength. Extra thick vinyl skins. American made.

Correct texture and molded-in colors, with steel insert molded into foam to increase strength. Extra thick vinyl skins. American made. NOTE: The color on this armrest is incorrect and is a darker shade of brown, rather than the correct ginger color. Replaces Ford part # D1ZZ-6524101.

Correct texture and molded-in colors, with steel insert molded into foam to increase strength. Extra thick vinyl skins. American made. NOTE: The color on this armrest is incorrect and is a darker shade of brown, rather than the correct ginger color. Replaces Ford part # D1ZZ-6524100.

These plastic backing plates are found on all 71-73 Cougars with standard interior. Since most Cougars had decor or XR7 interior we have a limited supply of these and cannot guarantee we can get the color you desire, but we will try to accommodate. Right is the same as left. Keep in mind these same parts can be found on many Fords and Mercury's throughout the 70's

This is the arm rest base for the driver or passenger side on any 1971, 192 or 1973 Mercury Cougar with standard interior as well as some Mustang trim levels.  Also fits multiple other Ford /  Mercury cars of the same vintage.Replaces Ford Part Number: D1AB-5724144

Correct texture and molded-in colors, with steel insert molded into foam to increase strength. Extra thick vinyl skins. American made.

Correct texture and molded-in colors, with steel insert molded into foam to increase strength. Extra thick vinyl skins. American made.

New screw with a correct 3/8 inch hex head for installing all armrests for all years.

This clip attaches to the textured steel dash top on many 1971-73 Ford, Mercury, and Lincoln cars. Mostly full sized and intermediate cars such as Cougar, Mustang, Torino, Cyclone, Montego, Ranchero, Lincoln, and Continental. 3 of these clips are used to attach the dash top panel to the cowl at the windshield. Sold individually. Brand new AMK clip.The curved tail kind of guides the panel into the slot at the front. The illustration for this part is shown on page 48 of the 1971-72 Mustang Body...

Reproduction Glovebox Liner w/ Air for the 1971 - 1973 Mercury Cougar and Ford Mustang

Glove box or glove compartment light with switch. Fits 1971-73 Mercury Cougar and Ford Mustang. Used switch and wiring assembly, tested and working. Fits 71 CougarFits 72 CougarFits 73 CougarFits 71 MustangFits 72 MustangFits 73 Mustang ...

Plastic injection molded, chrome plated like the originals. The detail on the top is not exact to original. Sold as a pair.Replaces Ford part number C8AZ-6221850-A

Polished stainless steel with correct internal black felt anti-rattle pad. Sold as a pair.

New old stock interior door handle or door pull. Molded rubber for decor and XR7 interiors. Driver and passenger side are the same. Handle only, no screws for attaching. May or may not have the Ford box, depending upon inventory. This listing is for blue color only.Replaces Ford part number D1WY-6522666-B.We rarely get NOS pulls like this one but we often have good used pull straps in stock for $70 and under. If you are wanting to save money on your driver then a good way to repair the...

New old stock interior door handle or door pull. Molded rubber for decor and XR7 interiors. Driver and passenger side are the same. Handle only, no screws for attaching. May or may not have the Ford box, depending upon inventory. This listing is for light green color only. Found on 1973 Cougars.Replaces Ford part number D3WY-6522666-B.We rarely get NOS pulls like this one but we often have good used pull straps in stock for $70 and under. If you are wanting to save money on your driver...

New old stock interior door handle or door pull. Molded rubber for decor and XR7 interiors. Driver and passenger side are the same. Handle only, no screws for attaching. May or may not have the Ford box, depending upon inventory. This listing is for taupe color only. Found on 1973 Cougars. We have several of these in stock, odd ball color is suitable for color change. Note that the price is the same as our Grade A used?Replaces Ford part number D3WY-6522666-A.We rarely get NOS pulls like...

This ashtray lid was located on the rear interior quarter panels and was used on all 1971-73 Mercury Cougars and Mustangs. This ashtray differs from other ashtrays you will see on various Ford products in that it has a brushed finish, is stamped steel and a slightly shorter lower base section. The removable ash receptacle is sold separately. Priced as driver quality grade B units, will have light pitting or scratches as shown.Ford part # D1ZZ-6530714-A. ...

This panel was used the full 1971 model year and early 1972 and is for use in cars with no rear seat seat belt re-tractors. It will not show serious UV damage with the "chalky look" and will have no extra holes drilled. These are very hard to obtain so we rarely have more than a couple on hand, please email us for colors on hand.

Unlike the reproduction, we have this available in multiple colors. Call for availability. Fits 1970, 1971, 1972, and 1973 Mercury Cougar. Ford part # D1ZZ-13915-A Used in conjunction with the deluxe trim plate.

Perfect fit.

If you have already begun to install or have installed this item, it is not eligible for return or refund. This rim blow horn switch is made in the United States by Daniel Carpenter Mustang and is made from vinyl like original. When installing, make sure to massage the rim blow switch in place with counter clockwise, compacting strokes. Clockwise strokes (thumb motions) will stretch the switch and when you complete the installation you will find the part has become too long to fit in place...

1970-74 Mercury Cougar rimblow horn pad bezel with hand painted woodgrain. These have been painstakingly hand painted by a local artist. 1970-74 standard and 1970-74 XR7 straight style wood grain. Does not include the 'kitty', 'kitty' sold separately. Cores cannot be bent or rusted heavily. Does not include the 'kitty', Cougar Emblem sold separately. Cores cannot be bent or rusted heavily.Core charge is refundable when restorable 1970-74 woodgrain insert is received by WCCC. ...

Good used part with a little peeling on the foil and this part will most likely have cracks. Of the three studs on the back you can rest assured one if not two of the studs will have cracks or a portion missing. Contact us for the many options as we have over 50 in stock. We sell the metal woodgrain painted center section separate.

This is the chromed correct die cast construction for your 1969 Cougar, 1970-73 used plastic but these will fit fine and look better than the plastic units. Great Quality. Sold individually, two required per car. Part of the XR7 package. Available on other hardtop models, part of the Courtesy Light group option. Option included, engine compartment light, trunk light, map light and these rear quarter panel lights for the back seat. Replaces Ford Part #: C4SZ-13776-B.*Trivia Dearborn built...

Optional trunk lamp. Includes mercury switch that mounts on inside trunk lip and wiring pigtail. Driver quality part, Bulbs available. Guaranteed to work, no cuts or splices. Can be added to most cars. Single wire female connector, located near the drivers side trunk hinge. Self grounds to deck lid, one power lead wire. Mercury switch turns on and off with the raising and lowering of the deck lid.

Reprint of an original pamphlet that was intended to help Ford techs date and identify by using the codes found on the parts. Covers all LFM models, 23 pages.

Have you been in a discussion with someone about how many W-code GTEs were made? The real percentage of Cardinal Red convertibles that were made? How many Eliminators were made each year? Now you'll know these things and so much more. This book contain never before published information drawn direct from company records, and over 14,000 statistics. This book includes: Exhaustive charts of paint color-trim combinations Engine-transmission production for each body style Option production rates...

This 165 page book has been in the works for over a decade now at Marti Auto Works and it is a must have for anyone purchasing, restoring or researching a 1967-1973 Mercury Cougar, Ford Mustang or Shelby. Even if you are a Mopar or Chevrolet guy, if happen to frequent swap meets and salvage yards you need this invaluable little book tucked away in your tool box or car as you maybe walking right past VERY valuable cars and parts and not even know it... In Kevin's words, "Have you been...

Manual on how to modify your FE big block Ford for street or strip.

Complete reprint of 11 Supplemental Off Highway Performance Operation Parts Newsletters from Ford which were printed between January 1972 and Spring of 1973. Full of tips on modifying your vehicle for Drag, Strip and Oval Racing.

Used Mercury Product Data Book for the entire Mercury lineup for the 1972 model year run. This is a rare gem for sure as these were typically thrown away as soon as the dealership got the new information for the new model year. These books were used as reference material and to train their sales staff. Below is a list of SOME of the systems you will find information on in this book.Air Conditioning Appearance Protection Group Body Construction Brake Systems Carburetor&n...

Saves time and frustration! Shows schematic and diagrams that reveal the location and function of the many vacuum systems on Cougar's.

Great option for international customers. Light weight, and all you need is a PC or laptop, and you can plug this drive in and access all the same information that you'd find in the full sized shop manual books.

This USB flash drive contains the electronic collection of the 64 - 71 Ford Car and Truck Technical Service Bulletins (TSB) released from October 19th 1964 through September 10th 1971. Technical service bulletins are official communications between Ford and their dealerships that describe processes for troubleshooting or fixing certain common problems. TSB's document recommended procedures for repairing vehicles, when there are several occurrences of an unanticipated problem. TSB's can range...

This USB flash drive contains the complete Autolite 4300 carb information from overhauling, to diagnosis and repair. A must for anyone planning to work on their own carburetor. This USB contains detailed instructions on disassembly and assembly of all major components. This USB version of this manual is a great option for international customers. Light weight, and all you need is a PC, laptop or tablet (with USB support), and you can plug this drive in and access all the...

These are OEM replacement bushings. The problem with these are most original sets are rusted out on the metal parts. We highly recommend the upgrade, unitized sets we sell over the orignal design.Replaces Ford Part #: C6OZ-3A187-A

This panel was used in most of 1972 and all of the 1973 model year and is used in conjunction with cars equipped with rear seat seat belt re-tractors. It will not show serious UV damage with the "chalky look" and will have no extra holes drilled. These are very hard to obtain so we rarely have more than a couple on hand, please email us for colors on hand.

This panel was used in most of 1972 and all of the 1973 model year and is used in conjunction with cars equipped with rear seat seat belt re-tractors. It will not show serious UV damage with the "chalky look" and will have no extra holes drilled. These are very hard to obtain so we rarely have more than a couple on hand, please email us for colors on hand.

This panel was used in most of 1972 and all of the 1973 model year and is used in conjunction with cars equipped with rear seat seat belt re-tractors. It will not show serious UV damage with the "chalky look" and will have no extra holes drilled. These are very hard to obtain so we rarely have more than a couple on hand, please email us for colors on hand.

This panel was used in most of 1972 and all of the 1973 model year and is used in conjunction with cars equipped with rear seat seat belt re-tractors. It will not show serious UV damage with the "chalky look" and will have no extra holes drilled. These are very hard to obtain so we rarely have more than a couple on hand, please email us for colors on hand.

This panel was used on all convertible models without retractable seat belts. Please contact us for choice of color, power or manual windows and with or without seat belt re-tractors. It will not show serious UV damage with the "chalky look" and will have no extra holes drilled.

This ashtray lid was located on the rear interior quarter panels and was used on all 1971-73 Mercury Cougars and Mustangs. This ashtray differs from other ashtrays you will see on various Ford products in that it has a brushed finish, is stamped steel and a slightly shorter lower base section. The removable ash receptacle is sold separately. Priced as good quality grade A units, no pitting.Ford part # D1ZZ-6530714-A.

This listing is for a premium quality pair of 1970 original strut rods in grade "A" used condition. What sets them apart from our grade "B" rods is that after they have been bead blasted they have a smooth finish, no pock marks from rust. This is for the person who is doing a show car and wants the very best, original correct parts that can be found. The reproductions are made in China and work fine but they are different on every detail and do not come with the specialty bolts that attach the...

Nice used passenger side strut rod that fits all 1970-73 Mercury Cougar and Ford Mustangs. Our good used Western strut rods are the best you will find. No bends, nor damaged threads, not heavily rusted and correct for your Mustang / Cougar and 1970-71 Torino, Cyclone, Ranchero.. Functionally the same as 1968-69 strut rods, just not stepped down threads at the end. Ford part number C9ZZ-3468-D. Sold as a bare strut rod, we also offer the used hardware for installation here. ...