All Available Parts - 1971 Ford Mustang

Original Ford style fasteners used on most all Ford products starting in 1968. Sold in pairs. Zink (dark silver)

These are the screws that are used to attach the door latch to the door shell on the 67 - 73 Cougar or Mustang. Sold in a set of 6.

Sold individually. Replaces Ford Part # 388052-S Helpful tip: Door panel clips install sliding toward the rear of the vehicle.

1/4-20x1 inch stud. Sold individually. Found on various years and parts of Cougars. Used for attaching 1967-68 grilles to the headlight buckets. Also as replacement mounting studs for front and rear fender and quarter extensions. Zinc Dichromate (yellow-rainbow)

replaces Ford part # 385161-S Zinc - Dichromate (yellow - rainbow) finish

Complete engine mounting hardware kit for the 1970-71 351C 2-barrel engine. See list below to see what is included. Click on images to enlarge.

AMK engine fastener kit for 1971 Mercury Cougar and Ford Mustang with J or C code 429 Cobra Jet engines. This kit claims to have 136 pieces. This kit additionally fits 1970-71 Ford Torino and Mercury Cyclone and other variants with 429CJ engine.Kit typically includes: fasteners to attach air cleaner, carburetor, crank pulley, distributor / points / condenser / vacuum advance, drain plugs, engine tag, exhaust manifolds, fan / fan clutch, fuel pump, shroud, ignition coil and strap, intake...

Complete engine mounting hardware kit for the 1970-71 351C 4-barrel engine. See below for list of incuded items. Click on images to enlarge.

Bolts and installation kit for most 1970-73 Mercury Cougar and Ford anything, including Mustang with V-8 engines. Kit includes main pivot bolt and adjusting bolt as shown. Spacer not included, but available used.

Used bolt and washer from a factory installed AC Compressor 1967 - 1973 Mercury Cougar - 1967 - 1973 Ford Mustang. Attaches clutch to compressor shaft.

Replaces Part # C9OB-3B284. We also have this bolt available in fine thread but only as a used bolt. Four required per car. Sold individually

part # 370608-S. Used in multiple places on mounting brackets.

This nut fits onto the strut brace at the front of the car, and not the control arm end.Replaces Ford part # 380517-S

part # 383722-S Pivot bolt for use with the all steel 1970-73 power steering pump mounting bracket. NOS new old stock! Fits most all Ford 302/351 from 1970-73 with the above described bracket.

OEM style nut to hold the axle U-bolt to the axle. Fine threaded like originals 7/16-20 grade 5. Will not fit some reproduction U-bolts. Sometimes these are called shock plate bolts. Replaces Ford part # 379244-S

part# 384114-S100 Sold individually Check out our caliper tips and tricks video below: ...

Reproduction adjustment cam / bolt for the lower control arms of the Mercury Cougar or Ford Mustang. We also offer this used version as well. These units are sold individually.Ford part # C6OA-3B236-A.

1/2"-13 x 4 1/2" grade 8 flanged bolt with a phosphate and oil finish.  Ford Part # 382486-S.

replaces Ford part # B-12764

Replaces Ford part #375381-S Phosphate & Oil Finish

Fine thread lock nut used in various places on old Fords, including the differential housing, 1967 disc brake assemblies, and more. Replaces Ford part # 34445-S

Reproduction nut that replaces Ford part # 34033-S. This is the nut that secures the pitman arm to the steering box. Has correct 7/8"-14 threads. Split washer also needed, not included, nut only.

Reproduction disc brake hose bolt for any 1968-73 Mercury Cougar and generally all other Ford cars with factory disc brakes. Special hollow bolt with cross drilled hole. Attaches the high pressure hose to the caliper.

Fits both 8 inch and 9 inch rear ends. Phosphate and oil coated with thread sealer. These are one time only nuts. They should not be reused per Ford. Replaces Ford part #: 371518-S

Sold indiviually Phosphate & Oil (gay-black)

Sold as a pair. Replaces Ford Part # : D0OZ-8052 Check out our video on Radiator and Fan upgrades below:

New valve cover bolts for all Boss 302, 351C-2V, and 351C-4V Ford engines. These are the AMK bolts with original style Ford assembly line head markings. Correct 7/16 hex head and split tooth captured washer, sold in sets of 16.*Note - Excludes 289/302 and 351W engines (see part  number 8316)1/4-20 X 5/8" Hex Head Bolt with Electrolytic Zinc & Wax finishReplaces Ford part number 373071-S.

Reproduction brake and fuel line clamp kit for Mercury Cougars and Ford mustangs equipped with disc brakes.

Reproduction brake and fuel line clamp kit for Mercury Cougars and Ford Mustangs equipped with drum brakes.

Cable length 22.50 inches long. Has clevis and pin on the end for attaching to the throttle pedal assembly. *Note - Used on Cougars prior to 7/10/1972 look at your throttle pedal end.

Bracket that mounts to firewall for accelerator shaft. 1971-73 Mercury Cougar and Ford Mustang. 

York compressor for air conditioning systems for Mercury Cougar and Ford Mustang. These should be professionally inspected or rebuilt and our compressors have all been in storage for some time. Shipped without pulleys, clutches, or valves. The York compressor is constructed mostly of aluminum and is lighter than the Tecumseh brand compressor by 10 pounds. The York compressors are less common too, subject to availability. We often see part numbers on the York tag (which does not list a Ford...

Tecumseh compressor for air conditioning systems for Mercury Cougars and Ford Mustangs. These should be professionally inspected or rebuilt and our compressors have all been in storage for some time. These Tecumseh compressors came with a front oil fill plug up until 1967, thereafter, they have a top fill plug. Top fill is the most common, and likely what you will receive, unless you specify the 1967 style with front fill. These units are shipped without pulleys, clutches, or valves. The...

Brake line rubber grommets for any 1967-73 Mercury Cougar or Ford Mustang. These are the ones that go through the shock towers for the front brake lines. Drum or disc, all the same. Sold as a PAIR. Ford number 373624-S.

Used bolts, and usually new washers. Convertible kit comes with 4 - "A" bolts, 4 "B" bolts, 10 new washers. Kit fits all 1970-73 Mercury Cougar and Ford Mustang convertibles. Coupes or hard tops would include shoulder belt hardware. We will make sure these original seat belt bolts are damage free and rust free. The gold finish will be degraded. There were minor and major changes almost every year. We also have hundreds of used belts and belt sets that we cannot possibly list all of, so give us...

384543-S8 Power steering pump adjusting spacer for use without air conditioning. For most 1970 - 1973 Mercury Cougar or Ford Mustang with 351C engines. Spacer dimensions: 7/16" I.D. and 1/2" thick.*Note 1970 and later cars with 302 or 351W engines use a 3/4 inch spacer.

This Super Cobra Jet emblem was never used on a Cougar, but is the Cobra Jet emblem used on the Hood Scoop for 1969-1970 Mustangs. It is also an attractive emblem for your custom application. Thanks for the plug Mark!: "My first deal with Don was clear back in the 1980s and I have sent a few people his way and all came away happy. While at his shop on Monday I watched Lin crawl under a convertible, phone in one hand and a tape measure in the other, and measure a cross...

These are sold individually, two required per car. This is the aluminum emblem / decal which mounts on the center of some late 67 and all 68-73 scuff plates. Features raised script like original. Adhesive backed with a protective coating that peels off after installation. Replaces Ford Part #: C7ZZ-6513208-T. Licensed by FORD ...

Concours? almost, these are stainless steel screws with the wax tipped coating like the originals, for installing the door sill plates. The wax was deemed necessary by the Ford Motor Co. as a seal. These can be used on all years 1967-73 Mercury Cougar, Ford Mustang and most all other Ford, Mercury, Lincoln cars of the era. Works well with any of the reproduction sill plates, these were really made to be used with the premium reproduction sill plates in stainless steel. 1967-68 Cougar and...

Good quality but not as good as original in that it is too shiny. Fits Coupe or convertible, left or right. Sold individually. Ford emblem sold separate. Replaces Ford part # D1ZZ-6513298-A

Good deal for the guy missing a sill plate on a driver. Sold individually.

Reproduction stainless steel scuff / sill plate. Fits Coupe or convertible, left or right. Sold as a pair. Ford emblem sold separate, find it here. Replaces Ford part # D1ZZ-6513298-A

Concours? almost, these are stainless steel screws with the wax tipped coating like the originals, for installing the door sill plates. The wax was deemed necessary by the Ford Motor Co. as a seal. These can be used on all years 1967-73 Mercury Cougar, Ford Mustang and most all other Ford, Mercury, Lincoln cars of the era. Works well with any of the reproduction sill plates, these were really made to be used with the premium reproduction sill plates in stainless steel. 1967-68 Cougar and...

Door striker replacement bushing.   .90 tall, .69 OD. .49ID. .10 thickness. These plastic bushings were used starting in 1972. We also sell the whole striker assembly. Common striker to many Ford cars after 1971. Apparently Sikorski helicopters too.

Door Striker bolt assembly complete with PVC bushing. 7/16-14 thread. Silver zinc finish. Replaces Ford part #: D2AZ-6522008-A.

Plastic insert with metal locking retainer. Replaces Ford part # C5AZ-6221952-A. NOTE* This clip will need to be squeezed on the clip side in order to obtain a good grip. Check out our handy diagram below to find other '67-'68 door parts you may need. All the item numbers shown can be typed in to the search bar on our site. (Click image to view full size) ...

Replaces Ford Part #: D1ZZ-6221813-A

Replaces Ford Part #: D1ZZ-6221812-A

Convenient matched sets save costly locksmith work. Kits includes a pair of door lock cylinders. Comes with two keys. Includes door cylinder gaskets. If you don't mind have having a different key for the door locks, this product might just work out.Attention potential buyer! This item will likely give you problems and be a general disappointment. Reviews show that the fitment is fair, and you will not be able to have these lock cylinders re-pinned, to use your original Ford key. One...

Ignition lock set is new original from the O.E.M. source. Factory fresh with two keys. Fits 1970 through 1973's manufactured before 5/17/1973. Replaces Ford Part #: D0AZ-11572-A, D2AZ-11582-B, SW-1114.

These are the screws that secure the door latch mechanism to the door shell. These screws come with the attached crown headed lock washer, just like the originals, so be sure to tighten them down snugly to ensure that the screw head sits flush into the screw holes. Sold individually. Three required per door, six per car.

Door lock latch lever, for driver or passenger side locks. Attach with an "E" clip on the rear side of the lock mechanism. Used "E" clip is included. We are going to say that these fit all Ford door locks 1965 through 1973 and beyond. *Note you will need to purchase or reuse your retainer clip for attaching the lock rod. Retainer clip not included, we have good used or reproduction clips, see related items.Ford number stamped C5AB-6221970-A or D2AB-6221970-AA  ...

Latch rod that links the door latch and the inside door handle, passenger side door. Fits any 1971-73 Mercury Cougar and Ford Mustang. Normally this rod was fabric covered. Used rod only, no retaining end clips.Replaces Ford part number D1ZZ-6521940-A.

Latch rod that links the door latch and the inside door handle, driver side door. Fits any 1971-73 Mercury Cougar and Ford Mustang. Normally this rod was fabric covered. Used rod only, no retaining end clips.Replaces Ford part number D1ZZ-6521941-A.

Inside door handle release mechanism for the passenger side on early 1971 Cougar and Mustang. Early because this latch mechanism went through a couple of revisions by the end of 1973. Ford calls this part a 'control and link assembly', this particular one only works with the deluxe door handles as shown in the photo. The Ford MPC describes those door handles as fitting the door panels with molded armrests, instead of the smaller detachable armrests on the base interiors. This early style was...

Plastic insert with metal locking retainer. The plastic came in various colors, white, red, and black are common. Replaces Ford part # C5AZ-6221952-A.Check out our handy diagram below to find other '67-'68 door parts you may need. All the item numbers shown can be typed in to the search bar on our site. (Click image to view full size) ...

Reproduction rubber bumper for your 67 - 73 Cougar or Mustang door latch mechanism. The bumper sits on the inside of your door latch mechanism, and is there to dampen the blow from the striker when you close your door.

When ordering this item, you do not need to order a key blank, the key is included. If you need more than one key, you don't need to pay for multiple key cutting services, just buy extra blanks and mention it in the comment section of your order. This listing is for the ECONOMY version of the trunk / glove box key. We now have the ability and equipment from an old Lincoln Mercury dealership to cut keys for Fords "by the numbers". Instead of copying a worn key to make yet another key that...

Good used drivers side door latch for inside the door. Fits any 1971-73 Mercury Cougar and Ford Mustang. Comes as shown, we also have latch rods, fasteners, etc in the related items. Replaces Ford Part #: D1ZZ-6221813-A

Good used drivers side door latch for inside the door. Fits any 1971-73 Mercury Cougar and Ford Mustang. Comes as shown, we also have latch rods, fasteners, etc in the related items. Replaces Ford Part #: D1ZZ-6221813-A

Refurbished pair of door lock cylinders and ignition cylinder for all double cut key Fords 1970-73. These are coded to the original key code, which was stamped onto one of the door lock cylinders. Sometime after 1973, Ford changed the ignition lock cylinder end. We know it works through 1973, not sure of the change. It must fit the brass lock gear at the bottom of the cylinder hole in the side of the steering column. Refer to your shop manual for removal and installation. Includes two...

When ordering this item, you do not need to order a key blank, the key is included. If you need more than one key, you don't need to pay for multiple key cutting services, just buy extra blanks and mention it in the comment section of your order. We now have the ability and equipment from an old Lincoln Mercury dealership to cut keys for Fords "by the numbers". Instead of copying a worn key to make yet another key that doesn't fit properly, we can cut keys as they would have come from the...

One size fits all.  Set of 4.  Good replacement if not worried about show quality. 1967 – 1968 Coupe 6 Required per car 1969 – 1973 Coupe 4 required per car 1969 – 1973 Convertible 2 required per car Will also work on the 69 - 73 shifter bezels. 4 required. Not recommended for our Mass Backed Carpeting. Please see related items for the longer screws. Replaces Ford Part #: 381571-S

8-32 x 1 inch long screws for attaching automatic shift bezels on 1969-73 Mercury Cougar or Ford Mustang with added Mass Backed Carpeting. Shiny zinc screws as shown, set of 4. Replaces Ford Part #: 381571-S

This is the round metal threaded disc that attaches the D0ZZ-6523258-A bushing to the door glass brackets. About 1-3/4" in diameter, two each per door glass on a 1970. 1971-73 Mercury Cougar and Ford Mustang use 3 of these for retaining the door channel bracket. Ford part number 384289-S.Click on images to enlarge. Do you have questions about Glue-In vs Bolt-In glass? How about how to properly install Glue-In glass in your 1969 Cougar or Mustang? Check out our video below for some great glassy...

57084-S Attaching bolt with 7/16" hex head and captured washer. Among other things, it is used to attach the door run, window stops (all 3), both window stabilizers, and the window regulator. Same bolts for manual and power window regulators. Bolt sold individually, there are a good handful in each door. This bolt is used for bolting in the bolt-in glass on 1970, lower "L" bracket for rear quarter windows on 1971-73 Cougar and Mustangs.

Almost identical to the original, tab is a bit longer. *NOTE*1969 Cougar owners do not need this part as it is built in the the chromed plastic, rectangular bezel on the door panel.

Great reproduction of a rather hard to find part.

This is an exact replacement for a 1970 remote sport mirror. Nearly indistinguishable from a 1968. Obviously a larger ball and longer than found on 1969, 1971-73 remote mirrors. This threaded replacement wand will require you to cut 8/32" fine threads in your original controller. Your OEM mirror controller is made of a very soft metal so one can often install these as "self tapping".1967 and 1968 are different, see comparison picture. The 1968 version was rounded off due to new safety...

*NOTE* EARLY 69's USED THE 2112 MIRROR FOR BOTH PASSENGER AND DRIVER SIDES. LATE 69's USED TWO DIFFERENT SIZES FOR EACH SIDE (2124 for driver side, and 2112 for passenger side). BEFORE ORDERING, PLEASE CHECK YOUR DIMENSIONS AND COMPARE TO OUR LISTINGS. Precision cut replacement lens for any Ford product with sport mirror on the passenger side. This fits any FoMoCo Sport mirror 69 and up, left hand only. Comes with two round pieces of double sided tape. Keep in mind if your lens is bad and it...

Reproduction side view mirror screw. These screws are sold individually. Do you have riv-nut questions? Here are riv-nut answers!

Reproduction passenger side (right hand) sport mirror lens for the Mercury Cougar or Ford Mustang and Torino.The mounting screw, that holds the mirror assembly in, is not included by default but is an optional addon. Replaces Ford part # C9AZ-17698-B. Dimensions: 4 7/16" x 2 15/16" This version does NOT include the wording "objects in mirror are closer than they appear". We also sell the version with the wording. Do you have questions about installing a passenger side mirror or using...

Empty shell / head / housing only for a passenger side manual adjust mirror. Found on all FoMoCo products utilizing a manual mirror 1969 - 1973. The remote mirror heads found on many 1970's Ford products do not interchange with the manual "Bullet Style" mirrors. Most customers find our reproduction unit to be a better value as it comes with the mirror and mounting hardware. Do you have questions about installing a passenger side mirror or using Riv-Nuts? Check out this video ...

Lens with mounting hardware only for a passenger side manual adjust mirror. Found on all FoMoCo products utilizing a manual mirror 1969 - 1973. The remote mirror lens assemblies found on many 1970's Ford products do not interchange with the manual "Bullet Style" mirrors. Count on the glass being scratched. The value here is in adjustment / mounting hardware. This unit will be guaranteed to keep its adjustment and not be loose like many have become over the years. Keep in mind this item is...

We have created all of the components needed to economically install the steel nutsert or Riv-nut for the exterior mirrors that mount to the car doors. Our steel Riv-nut uses a 1/4 inch hole. You will need a 5/32 Allen or hex key, 3/8 inch wrench, and a 7/16 inch wrench. The Riv-nut needs to be assembled on the kit as shown prior to installation. The assembly is installed flush, in the pre-drilled hole. The Allen wrench and the 7/16 are held stationary, while the 3/8 wrench is used to tighten...

*NOTE* EARLY 69's USED THE 2112 MIRROR FOR BOTH PASSENGER AND DRIVER SIDES. LATE 69's USED TWO DIFFERENT SIZES FOR EACH SIDE (2124 for driver side, and 2112 for passenger side). BEFORE ORDERING, PLEASE CHECK YOUR DIMENSIONS AND COMPARE TO OUR LISTINGS. Precision cut replacement lens for any Ford product with sport mirror. This fits any FoMoCo Sport mirror 69 and up. Comes with two round pieces of double sided tape.  Lens measures 4 3/8 X 2 7/8. Do you have questions about installing the...

Reproduction convex lens for a passenger side manual adjust mirror. Found on all FoMoCo products utilizing a manual mirror 1969 - 1973. The remote mirror lens assemblies found on many 1970's Ford products do not interchange with the manual "Bullet Style" mirrors. The screw that holds the mirror assembly in, is not included by default but is an optional addon. Replaces Ford part # C9AZ-17698-B This version included the words "objects in mirror are closer than they appear". We also sell the...

This mirror nut for the 70 - 73 Cougar or Mustang is made from stainless steel, as compared to the other reproduction we offer which is made from die cast metal. A few benefits of the stainless steel nut is that the finish on it will not tarnish over time, and that it cannot be cross threaded.

Pan head screw for attaching the sport mirror glass assembly into the passenger side painted sport mirror head. Found on all FoMoCo products utilizing a manual mirror 1969 - 1973. 8-32 pan head screw with Phillips screw head. Do you have questions about installing a passenger side mirror or using Riv-Nuts? ...

Set of 20 replacement staples for the beltline kit. These are used to attach the beltline pieces to the door panel. Will work for any beltline kit on a number of different makes and models.

This cut to fit 4" pin will fit any 67 - 73 Cougar hinge upper or lower. Sold individually, four required per car. Check out our hinge rebuild video below for more info.

Most times when your door sags you do not need new hinges but rather pins and bushings. If your holes are reemed or "hogged out" you will need to buy new hinges or our good used hinges that come with new pins and bushings. Sold individually, eight required per car. I.D. 11/32"O.D 7/16" These bushings are not the same as those offered by some of the "Discount Mustang Shops".  Several of the reproductions of this bushing are too large diameter and require you to drill out your hinges...

These original hinges have been rebuilt with steel sleeves to retain the over-sized oil impregnated bushings. They feature hollow hinge pins which allows grease to fill the steel tube, lubricating the bushings under pressure from the inside-out. The threaded Zerk fittings are easily accessible from inside the car when the door is opened and are guaranteed to NEVER wear out or we will rebuild them for FREE! This offer has been in place for 20+ years by our rebuilder and they have never been...

Includes 4 cut to length hinge pins and 8 hinge bushings. Replaces Ford Part #: C9ZZ-6522800

We highly recommend restoring our rust free Western hinges over using reproduction hinges. The main reason the originals are better than the Taiwan made reproductions is fit. If there is anywhere in which you want a precision fit it is in the hinges. These hinges have not been worn to the point of being "hogged out" and have been carefully inspected for cracks. You will want to purchase a new hinge pin and 2 bushings though. Check out our hinge rebuild video below for more info. ...

We highly recommend restoring our rust free Western hinges over using reproduction hinges. The main reason the originals are better than the Taiwan made reproductions is fit. If there is anywhere in which you want a precision fit it is in the hinges. These hinges have not been worn to the point of being "hogged out" and have been carefully inspected for cracks. You will want to purchase a new hinge pin and 2 bushings though. Check out our hinge rebuild video below for more info. ...

We highly recommend restoring our rust free Western hinges over using reproduction hinges. The main reason the originals are better than the Taiwan made reproductions is fit. If there is anywhere in which you want a precision fit it is in the hinges. These hinges have not been worn to the point of being "hogged out" and have been carefully inspected for cracks. You will want to purchase a new hinge pin and 2 bushings though. Check out our hinge rebuild video below for more info. ...

We highly recommend restoring our rust free Western hinges over using reproduction hinges. The main reason the originals are better than the Taiwan made reproductions is fit. If there is anywhere in which you want a precision fit it is in the hinges. These hinges have not been worn to the point of being "hogged out" and have been carefully inspected for cracks. You will want to purchase a new hinge pin and 2 bushings though. Check out our hinge rebuild video below for more info. ...

These overseas hinges are not known for fitting well, we cannot recommend them and we do not accept returns or exchanges on them. Replaces Ford Part #: D1OZ-6522811-A

These overseas hinges are not known for fitting well, we cannot recommend them and we do not accept returns or exchanges on them. Replaces Ford Part #: D1OZ-6522810-A.

These overseas hinges are not known for fitting well, we cannot recommend them and we do not accept returns or exchanges on them. Replaces Ford Part #: D1OZ-6522800-A.

These overseas hinges are not known for fitting well, we cannot recommend them and we do not accept returns or exchanges on them. Replaces Ford Part #: D1OZ-6522801-A.

Whenever you take on a door job, its always handy to have a few things available....a helper, a floor jack and a door hinge wrench. While a helper and floor jack might not always be available, a door hinge wrench is a valuable tool to have around when removing / setting a door. This Snap on obstruction wrench (google snap on part # S9608B) is specially curved to allow you to gain access to a few of those hard to reach bolts on your door hinges. We will loan this door hinge wrench for 60 days,...

Retainer or keeper for door hinge pins on all 1968-73 Mercury Cougar and Ford Mustang, plus most all other Ford products with a typical door hinge pin. The factory installed the hinges with the pins driven in from the bottom as viewed with the doors installed. Most restorations install the pins from the top so that gravity holds them in. These retainers allow the pins to be mounted concours correctly. You must use a socket or other tool to install. These fit the door hinge pins with 5/16 inch...

Replacement rubber bushing for repairing any automatic shift arms on any 1967-73 Mercury Cougar or Ford Mustang, and most Fords with automatic floor shift levers. Fits arms with 3/4 inch lower holes for attaching transmission shift rods. Replaces Ford part number C7ZZ-7343 Check out our video on rebuilding your shifter below: ...

Restored chrome automatic shifter lever for some 1970 Mercury Cougar or Ford Mustang, and all 1971-73 Cougar and Mustangs, with or without consoles. Sometime in the 1970 era, Ford switched to a larger pawl. Easy to identify if you look at the slit on the lever. We sell these bare for those car owners that have pitted shifter levers. Ford part number C9ZZ-7210-C. *Note - Chromed lever only, sold without cable, pawl, handle, etc. Check out our video on rebuilding your shifter below: ...

Restored shifter T handle as found starting in 1968 and through, 1972 Mercury Cougar and Ford Mustang with automatic transmissions. This handle will actually fit on most Ford automatic floor shift levers of the era. Design is a little thicker in the body, compared to earlier designs. Core charge applies. Replaces Ford part number C8OZ-7213-A. Check out our video on rebuilding your shifter below: ...

Exact reproduction for the 1969 - 1973. Perfect fit and finish. You may want to replace yours with this inexpensive unit just for the fresh new luster alone. Your plastic end buttons may have faded to gray but they were originally black like this one. Replaces Ford Part #: C8OZ-7213-A, C90Z-7213-B, D3OZ-7213-A. Check out our video on rebuilding your shifter below: ...