My Lists
Login
Subtotal
$0.00
Shipping
Tax
Discount
Total
D1WY-17B883-A Bracket that mounts under the reinforcing beam, lower center bumper mounting point.
Used centering ring for any fixed or tilt column on a 1969 - 1973 Cougar or Mustang. *NOTE*For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year.
Used air conditioning distribution chamber. Comes as shown, plastic housing, internal flapper door with rod, with attached bracket for attaching vacuum actuator. Actuator and hardware sold separately. Unbroken condition, it will definitely need new foam on the door.Replaces Ford part number D1ZZ-18471-A.
Channel bracket cut from a car. This is the front bracket for mounting fuel tank straps on a 1971-73 Mercury Cougar. Mustang may be the same, just not sure. No Ford part number found. We cut it from a car, spot welds of the actual bracket will need to be drilled and cleaned up prior to installation. Make sure that you measure the exact location of this bracket before you remove from your car.
Correct check valve for both power drum and power disc brake cars. Comes with grommet.
Used transmission line adapter and check valve for all FMX transmissions. This fitting goes into the rear part of the transmission case and connects the rear most cooling line to the case. Has internal ball check valve to prevent fluid from back flowing. All FMX transmissions 1969-73 Mercury Cougar or Ford Mustang. The male threads going into the transmission case are 1/2-20 pipe threads.Replaces Ford part number C3AZ-7D174-A.
Reproduction Headlight / Tilt Column Vacuum Check Valve for the 1967 to 1973 Mercury Cougar, Cyclone, Marquis, Ford Torino, Ranchero, Galaxie, LTD, Thunderbird, Lincoln Continental and Mark III. NOTE: The direction of flow is up through the dual ports and out through the single port. For more in depth detail on this reproduction, see pictures below. *NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've...
Carburetor choke pull off for most 2V and 4V Autolite or Motorcraft carburetors 1958-74. Diaphragm with a hook on it, to 'pull off' the choke. Ford basic part number is 9J549, part of the dashpot assembly. We do not think that it will fit Holley carburetors. Also fits AMC and Jeep that used Autolite and Motorcraft carburetors.
Used cast iron choke stove from any 1970-73 351C-2V Ford engine. This is held on with 4 bolts, and to our knowledge no block off plate is reproduced. Casting number on the iron plate is D0AE-9A705-D, which is only for the plate. The plate and coiled tube assembly has a Ford part number of D0AZ-9C869-B. No hardware included.
Cigar or cigarette lighter for 1971-73 Mercury Cougar and Ford Mustang. Slight change from the 1970 style, this one has a black plastic shaft. Ford part # D1ZZ-15052-A.
New cigar or cigarette lighter with socket and retainer assembly for 1971-73 Mercury Cougar and Ford Mustang. Ford part # D1ZZ-15052-A.
Used 20 amp circuit breaker for either 69 - 70 or 71-73 Cougars.Mounted on the Starter solenoid in 69-70 cougars for convertible tops or power windows, and also on 71-73 Standard Cougars for convertible tops, power windows, heated back light, power seats or seat back release.On the 71-73 XR7 the circuit breaker was mounted next to the starter solenoid on a junction block. Different wire diagrams, owner / shop manuals list this circuit breaker in both locations, possibly due to multiple...