All Available Parts - 1971 Mercury Cougar

D1ZZ-7400-A 3 Speed manual transmission shift control assembly for any 1971 - 1972 Mercury Cougar or Ford Mustang. Check out our video on rebuilding your shifter below: ...

D1ZZ-7400-A3Assembly Factory 3 Speed manual transmission shift control assembly for any 1971 - 1972 Mercury Cougar or Ford Mustang. Includes shifter mechanism, shift rods, and shift lever. All in used condition. The Ford MPC states that this same shifter was used on 6 cylinder Mustangs and all V8 Mustangs and Cougars as large as the 351-2V engine. Additionally Ford continued to use this shifter on 1973 Mustang with a 6 cylinder or 302-2V engine. Check out our video on rebuilding your shifter...

Good used single sheave pulley for the alternator on the 429 Cobra Jet.Ford Part #: D1ZF-10A352-AA.

Reproduction gold dichromate 10 blade alternator fan. Used on Mercury Cougars and Ford Mustangs manufactured after 11/17/1969. Actually this is a Ford part found on most all Ford automobiles from 1970-73. 10 blade alternator cooling fan. Replaces Ford Part #: DOAZ-10A310-B

Mounts to the frame on the left side of the fuel tank. Supports and holds the rear of the tailpipe stationary. 1971 all 351 and 429CJ with dual exhaust. 1972 all 351 with "Quiet" and "Sporty" dual exhaust. Ford part number D1ZZ-5260-E. *Pipe clamp D1AZ-5A231-C needed 2" diameter pipe "Quiet". *Pipe clamp D1AZ-5A231-A needed 2-1/4" diameter pipe "Sporty".

1971 *351-4V prior to 4-12-1971. 1972 and 1973 351-4V with "Quiet" dual exhaust. Holds the rear of the muffler to the underside body. Ford part number D1WY-5260-B. *Early production prior to 4-12-1971.

D1ZE-9431-B 351-4V Cleveland factory original cast iron exhaust manifold for driver side. At some point there may have been a D1ZE-9431-BA casting number used, which may be substituted as per the Master Parts Catalog. *351C-4V exhaust manifolds only match up to factory 4V intake manifold ports and some aftermarket aluminum intakes such as offered by Weiand and Edelbrock.

351-4V Cleveland factory cast iron 4V exhaust manifold set, both correct right and left set of matching exhaust manifolds. Manifolds the same 1971-1973.

Yoke style factory exhaust pipe clamp. For 2-1/4 inch outside diameter exhaust pipes. Two piece clamp see picture Ford part number D1AZ-5A231-A.

351 Cleveland factory cast iron 2V exhaust manifold set, both correct right D1OE-9430-AA and left D1ZE-9431-AA side matching exhaust manifolds.

D1OE-9430-AA 351-2V Cleveland engine, factory original cast iron exhaust manifold for passenger side. *351C-2V exhaust manifolds only match up to factory 2V intake manifold ports and some aftermarket aluminum intakes such as one offered by Edelbrock.

429CJ factory cast iron exhaust manifold set, both correct right and left set of matching exhaust manifolds.

D1ZE-9431-CA 429 Cobra Jet factory original cast iron exhaust manifold for driver side. At some point there may have been a D1ZE-9431-CA1 or a D1ZE-9431-CA2 casting number used, either of which may be substituted as per the Master Parts Catalog. The current manifold in stock has a casting date of 4-28-70.

D0OE-9430-A 429 Cobra Jet factory original cast iron exhaust manifold for passenger side.

Single cylinder head from 1970-71 Mercury Cougar with M code 351C-4V engines. Sold as a core, needs thorough cleaning and rebuilding prior to use. Typically this cylinder head has 2.19 and 1.71 inch valves, and the chambers measure out at 62.8 cc's. These are considered 'Closed Chamber Heads'. With stock pistons, these heads will net an approximate compression ration of 10.7:1. Basic cylinder head number is 6090. Several Ford casting numbers were used, including the common D0AE-N. 4V in the...

Original equipment 4 speed top loader transmission from a 1971 Mercury Cougar with engine code M 351-4V only. Transmission code 5 on the door tag, this would be a wide ratio 4 speed transmission with a 2.78 ratio first gear.Ford part # D0ZZ-7003-D, Ford casting # RUG-AV1. Percentages of Cougars equipped with a manual transmission by year1967 = 18.5%1968 = 13.2%1969 = 10.5%1970 = 7.8%1971 = 2.8%1972 = 1.5%1973 = 0.7%Total for 1967 to 1973 = 10.1% (Mustangs for the same time frame were...

Original equipment 4 speed top loader transmission from a 1971 Mercury Cougar with engine code J 429 Cobra Jet and engine code C 429 Cobra Jet. Transmission code 6 on the door tag, this would be a close ratio 4 speed transmission with a 2.32 ratio first gear. The tailshaft on this transmission has a different bolt pattern for the Hurst shifter plate.Ford part # D0ZZ-7003-H, Ford casting # RUG-AZ1.

Original equipment 4 speed top loader transmission from a 1970 Mercury Cougar with engine code Q 428 Cobra Jet. Additionally 1971 Mercury Cougar with engine code J 429 Cobra Jet and engine code C 429 Cobra Jet. Transmission code 6 on the door tag, this would be a close ratio 4 speed transmission with a 2.32 ratio first gear. The tailshaft on this transmission has a different bolt pattern for the Hurst shifter plate.Ford part # D0ZZ-7003-H. Casting numberRUG-AZ or RUG-AZ1.*NOTE* Technically...

Timing chain set for your 67 - 72 Cougar or Mustang equipped with the 302 Engine.Gears (sprockets) are made from high alloy steel, and heat-treated for durability. Chain is pre-stressed and heat-treated for longevity.

Used rear window defog switch and knob assembly with mounting bracket for the 71 - 73 Standard Cougar.

Die cut vinyl decal in black. Measures 6 3/4" X 2 1/2". Adhering this decal to either the inside or outside of the glass will dictate whether it is a right or left facing cat. Check out the very first Cougar in our video below!

1971 *351-4V after 4-12-1971. 1971 429 CJ. 1972 with "Sporty" dual exhaust. Engine designated as a 351-CJ on air cleaner lid. Holds the rear of the muffler to the underside body. Ford part number D1WY-5260-D. *Late production - after April 12, 1971.

This poster is a meticulous recreation of the 1968 original that Lincoln-Mercury dealerships had on display in their showrooms to advertise the Cougar XR7-G. We were able to have an original poster professionally scanned, the images were restored, and the text carefully recreated to match the original. The result is a fresh new version of a rare, iconic display piece.This 24" x 36" poster is smaller than the original, which was a massive 36" x 48". This makes it easier to display, and easier...

This rare accessory was only offered over the counter, it was not available as a factory option. Great upgrade for the 1970-1973 Cougar owner as cruise control was discontinued after 1969 and not offered again until 1974 on the Mercury Cougar.Ford part number C8OZ-9B742-AClick on images to enlarge. ...

C60Z-3047-A Used on many Ford products starting with the 1966 Ford Fairlane.

C7AZ-6571-B

D4AZ-18495-A

Sold as a set of three. Fits 1969-73 Mercury Cougar and Ford Mustang.Ford part number .

C8AZ-2B296-A

C8AZ-6223362-A. Sold individually, has a different look than our reproduction decals.

Original or NOS Ford distributor cap.

C4DZ-5415-A Sold as a pair

D2AZ-6522050-A Service replacement ignition and door lock set with keys. Fits 1970-72 Mercury Cougar and Ford Mustang as well as most all other Ford and Mercury car lines. *Note - Ignition lock cylinder is for system on steering column only.

This listing is for a 3 bolt type upper ball joint, NOS, original Ford Service replacement upper control arm assembly. We have a very hard time keeping these in stock but we keep the listing up as it is good for comparison sake when considering the differences between reproduction and OEM. Keep in mind, service replacement parts often differ slightly from what actually came on the car. Over the years tooling is often replaced or modified and suppliers of things like fasteners often change....

Very rare trim ring used in conjunction with a 15x7" steel wheel and small hub cap on the 1971 Cougar 429 CJ. Only a hand full of Cougars ever got this trim ring. This would also have been used on a few applications like a 1970 BOSS Mustang or 1971 429 Cobra Jet Mustang, Torino or Cyclone. We have various condition used rings at a reduced price as well, call for availability, sold individually.

This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit of 50% of our web price for parts delivered in hand or by carrier to our Brooks, Oregon location. If you're not interested in store credit, just shoot us an email and we will let you know if it's is something we can pay cash for. We do not send cash for parts in advance but we often can compensate you within hours of receiving the...

Very rare find in the original service replacement boxes dated 10-07-75. Sold as a pair.Ford part # C8WY-65502B20-A.Click on images to enlarge. ...

NOS heater cable for 1969 - 1973 Cougars or Mustangs that are not equipped with factory air conditioning.Ford Part #: D1ZZ-18518-A

C9AF-10A352-A or -B Alternator pulley for use with only one drive belt. Just under 2-3/4" inches in diameter. This later version would have a casting number of C9AF-10A352-A or possibly C9AF-10A352-B stamped on it. Ford master part number is C5AZ-10344-K like the above pulley.

Metal 2 piece bracket that mounts to the front of the radiator core support and separates the sight glass to dryer hose and the discharge hose from the condenser. Correct for 1971-73 Cougar and Mustang, and 1970-71 Torino, Cyclone, Ranchero, Montego.Replaces Ford part number D0OZ-19B632-A.

These are used hose clamps that have a tab and fold over on them selves. These were dipped in a rubber like substance to prevent chaffing. The ones that we have available do have some cracking or damage to this coating. It should be easy to 'dip' them again with the product that is available in most hardware stores. We normally see 2 of these clamps, or straps bundling the hoses on most cars. These clamps should fit a variety of different Ford and Mercury products, not just Mustang and Cougar....

This is actually a kit which includes 2 hoses, 2 o-rings, and a quick connect. When assembled this hose is approximately 78 inches long. The Ford Master Parts Catalog (MPC) kit number is C8OZ-19837-A.Sight Glass Hose to A/C Dryer Hose (Part # D1ZA-19835-A)Sight Glass Hose (Part # D1ZA-19837-A)Sight Glass (Part # SG3, D2AZ-19D695-BK or YF-342) 2 O-Rings (Part # L33,D2AZ-19D695-R or YF-368 and Part # H33, D2AZ-19D695-AE or YF-316)Quick Connect (Part # QF3,C1SZ-19B696-A or YF-241 and Part # QM6,...

Decent reproduction of the air conditioning sight glass hose for the Mercury Cougar and Ford Mustang. Hose texture is not the same and the sight glass itself is different, but length and fittings are correct. If your sight glass hose is not original or you do not have the 2 piece quick disconnect, you may need to purchase the complete sight glass hose kit. For 100% correct hose, please see our good used sight glass hoses. Includes Sight Glass Hose (Ford Part # D1ZA-19837-A or...

This is used on cars equipped with factory A/C to stop the flow of warm coolant when the A/C is on. Not an exact replacement, but it will work just fine. Replaces Ford part #: D4AZ-18495-A.

Windshield defroster nozzle for Mercury Cougar and Ford Mustang without A/C. This is a "A" grade unit and will have 1 or 2 scuffs in the plastic, or small crack in the flex hose. You will need to staple the flex part onto your heater unit. Very fragile part, almost always going to have Grade B, seldom will we have a Grade A used.Ford part # D1ZA-18A565-AD

Used connector plug that attaches to the A/C vacuum switch assembly on the 69 - 72 Cougar or Mustang. The six vacuum hoses are molded into the plug, and for those instances when someone has cut a hose, simply use a hose connector.

Used driver side air conditioning duct for any 1971-73 Mercury Cougar with factory or integral A/C. Connects the center manifold to the passenger side elbow or connector. Casting number on this part is D1WA-19C732.Replaces Ford part number D1WY-19B680-A or D1WA-19C732.*Note - This part does not fit a Mustang, which has a vertically mounted driver side dash register. This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts....

Here is our NOS vacuum valve assembly which is fairly hard to come by these days. This unit is for Mercury Cougars or Ford Mustangs with integral or factory air conditioning. This part is good until an assembly date of 1/3/1972 and, if you want, we also have good used pieces in stock for your Coug or Stang as well. Ford part # C9ZZ-19B888-A.

Stud that the factory line workers used for locating the air conditioning pedestal bracket. Then backed up with a nut. Used on 289 / 302 / 351W / 390 / 428CJ pedestals from 1967 - 1973. We sell this item as reproduction, see related items.*Note - Excludes 351C and 429CJ.

Used cast iron pedestal mount for the A/C compressor for Cougars and Mustangs equipped with the 429CJ engine.  Listed in the Master Parts Catalog (MPC) as # D0AZ-2882-A. Replaces part #  D0AA-2882-B.

Used 'Kelsey Hayes' 15x7" styled steel wheel with a new chrome 15" rim for your Mercury Cougar. These originally came 14x7" on the Cougar with a beauty ring. We take your original wheels and have a new 15x7" outer chrome rim installed. This purchase requires a core wheel be sent to us. The good news is that you can find these in 14x6" or 14x7" inexpensively when they have been damaged and rusted on the outer lip. As long as the centers are untouched they are good cores. We sell these...

Reproduction chrome spinner center cap for the Mercury Cougar equipped with the magnum 500 wheel. Actually, this unit will work on any Ford, GM or Mopar Magnum wheel. Looks great and the mounting system is far superior to the originals. These look really aggressive.*NOTE* When installing these die cast center caps, keep in mind over tightening will separate the backing from the chrome outer portion. Instead of over torquing, we recommend a good threadlocker which you can get right here. ...

Used 14x6" stamped steel wheel for the Mercury Cougar or Ford Mustang. We save some of the better stock wheels you will find out there and some have probably ridden in trunks most of their lives. Have a bent or damaged wheel? Don't have a spare? These have the larger center hub, and will fit the "Granada" disc brake rotors. Shipped bare. Various conditions, subject to availability. Used 'as is', wheel as found in the wilds of our wrecking yard.Ford part # D0DZ-1007-B. ...

Used 14x7" stock stamped steel wheel for the Mercury Cougar and Ford Mustang / Torino. Rare seldom seen size most commonly found on a Ford Torino. These were offered from 1971 through 1973 on the Cougar and 1970 - 1973 on the Mustang and Torino. Have a bent or damaged wheel? Don't have a spare? Total width is 8" with a 4" backspacing. Various conditions and subject to availability. Used 'as is', wheel as found in the wild.Ford part # D0OZ-1007-B.

Used 15x7" stock stamped steel wheel for your Mercury Cougar or Ford Mustang. Originally, this unit was a black painted steel wheel that came with a small cap and deep trim ring. Ford part # D0OZ-1007-A.

Unfortunately we are not presently offering this wheel as the supplier has been consistently sending us inferior product and poor customer service at an ever increasing price. Please consider our Legendary wheel line, here is a video that shows more: ...

These off-shore Magnum wheels are supplied to us by Scott Drake. We no longer carry the US made version as the quality was VERY inconsistent. This wheel has a 4 1/4" backspace. We now have Magnum 500 caps that feature the Mercury Logo and the walking cat caps as well. Center caps and lugs are sold separate.   NOTE! These wheels are intended to be balanced with a lugcentric adapter. They will not balance with a traditional cone spacer on the tire spin balancer. Many tire shops do not deal...

Set of 4 Chrome center caps with red background and chrome Mercury man logo. Better than original! These are held on by a sturdy plate and two screws from the backside which is much better than the original clip-on type. There are other reproductions out there but none are of this quality. When using center caps on Legendary wheels, you will need these adapter plates. *NOTE* Certain late model disc brake rotors and aftermarket rotors have a slight clearance issue with the dust cap and these...

Reproduction chrome spinner cap for the Mercury or Ford that is equipped with Magnum 500 wheels. This cap will also work with any Ford, GM or Mopar Magnum 500 wheel. With a mounting system that is far superior to the original, this unit will definitely give your ride a more aggressive look. *NOTE* When installing these die cast center caps, keep in mind over tightening will separate the backing from the chrome outer portion. Instead of over torquing, we recommend a good threadlocker which...

Get a grip with this very rare find! This used original Hurst T handle, or shifter handle, is a one year only unit with no set-screw as found on the 1970 shifter. Ford part # D1OZ-7213-A. Check out our video on rebuilding your shifter below: ...

According to the Master Parts Catalog (MPC), Early (before Jan 31, 1969) Cougar with a 3.91 or 4.30 rear end and a 4 speed manual would have been equipped with this reducer. Boss 302 and 428 Cobra Jet engines were the only cars that could be ordered with those rear end ratios. Check with the Mustang 428 Cobra Jet Registry for actual usage, Not always factory installed in 1968-69. Check it out, they have a lot of content on that site. Also found on 1970 4 speed Mercury Cougar and Ford...

Rod used for locking the 3 speed manual transmission in "Reverse". Connects to the lower tab of the steering column and the reverse control transmission lever shift arm. Prevents the transmission from shifting out of reverse when the ignition key is removed. Rod is about 12 inches long and was originally marked with a purple paint mark. The 3 speed manual transmission, could be ordered only on "H" code 351-2V engines in 1971 and 1972. Transmission code "1" on your door data tag. *Trivia - 1972...

Rod used for locking the 4 speed manual transmission in "Reverse". Connects to the lower tab of the steering column and the reverse control transmission lever shift arm. Prevents the transmission from shifting out of reverse when the ignition key is removed. Rod is about 13 inches long and was originally marked with a green paint mark.The 4 speed manual transmission, could not be ordered on the 351-2V engines. Only 351-4V's and 429CJ's in 1971, and 351CJ's (Q code) in both 1972 and...

C8AZ-7515-A Manual transmission clutch fork - 4 speed, stick shift transmissions. Fork measures 12-7/16 inches long. Alternate number C8AA-7541-A. Cougar 1971, 429 Cobra Jet engines. Mustang 1971, 429 Cobra Jet engines. Galaxie / LTD, 1968 - 1969, 428 / 429 Passenger car engines. 500, XL, Custom. *Trivia - This fork originally had a yellow paint mark for identification purposes.

New Old Stock Ford flywheel. 11 inch clutch, 164 tooth ring gear,12-3/8 inch bolt circle for clutch pressure plate. Cast iron with C5AE-A and C7TE-A. New, never installed Ford manual transmission flywheel. Fits 351W, 351C, and 351CJ. Ring fear installed, factory fresh.

Application for all 1971 - 1973 Cougars with a factory manual 3 and 4 speed transmission. Engine options include 351-2V, 351-4V, and 429CJ. Ford part number D1ZZ-6A023-B. If you have pictures, specs or one of these for sale we would like to hear from you.

Adapter plate for mounting the 4 speed shifter control assembly to the Top Loader transmission.Ford part # D1ZZ-7E046-B. Check out our video on rebuilding your shifter below: ...

D1ZZ-7E046-A Adapter plate for mounting the Hurst 4 speed shifter control assembly to the Top Loader transmission.

Backup lamp switch that mounts to the factory 3 speed shifter linkage. 69 70 71 72 Mercury Cougar and Ford Mustang applications. Autolite or Motorcraft switch number SW-947. Used up until 5-15-1972. Tested and working switch with wiring and plug.*Note - 3 speed switches are different than the manual 4 speed switches.

D0ZZ-15520-A Backup lamp switch that mounts to the factory 4 speed shifter linkage. 70 71 72 73 Mercury Cougar and Ford Mustang applications. Autolite or Motorcraft switch number SW-943. Used with OEM installed Hurst Competition shifters. *Note - 4 speed switches are different than the manual 3 speed switches.

D1ZZ-15525-A 71 72 73 Mercury Cougar and Ford Mustang with the factory installed Hurst shifters. Plugs into the backup lamp switch and connects to the harness plug on the firewall behind the engine.

According to the Master Parts Catalog (MPC), any Cougar with a 3.91 or 4.11 rear end and a 4 speed manual would have been equipped with this reducer. Boss 302 and 428 Cobra Jet engines were the only cars that could be ordered with those rear end ratios. Check with the Mustang 428 Cobra Jet Registry for actual usage, Not always factory installed in 1968-69. Check it out, they have a lot of content on that site. https://www.428cobrajet.org/id... This is a part that we will probably never...

4 speed Top loader only. Ford part number D0AZ-6392-A Shipped bare, no hardware or clutch fork.

New internal speedometer gear fits 4 speed toploader transmissions. The largest number of 4 speed toploaders came stock with this gear. Replaces Ford Part #: C4DZ-17285-A.

D1TZ-7600-A New Old Stock service replacement clutch pilot bushing for all 1965-71 390/428/429 engines with manual transmissions. Will fit 1967-71 Mercury Cougar and Ford Mustang with 390-4V, 428CJ, 428SCJ, and 429CJ engines with 4 speed manual transmissions. Fits Fairlane, Cyclone, Torino, Ranchero also.

Ford small block engines and with a 3 or 4 speed manual transmission. Fits only the larger 164 tooth flywheel.

Used original pan removed from a Western parts car, 14 bolt holes. This pan is not available new. These will have some likely have some minor scrapes. These were not painted originally, may have light rust that will clean up. The best available, won't be in stock often. See our Grade B pans for less than half the price. This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit of 50% of our...

This very rare part is unique to the 1970 - 1971 CJ and SCJ C6. There was no 390 option in 1970 - 71. Sales were down on the CJ equipped Cougars in 70-71 making this one very hard part to obtain.  We have determined that this part only fits Mercury Cougar and Ford Mustang. Torino and mid sized Ford/Mercury use a different numbered part. Marked D0ZP-D. Ford Part #: D0ZZ-7A256-D. Check out our video on rebuilding your shifter below: ...

Original dipstick tube. Application 1970 - 1972 Mercury Cougar or Ford Mustang with FMX automatic transmissions, code "X" on your door data plate. These have a little longer tab than the 1969 FMX dipstick tube.Ford master part number D0OZ-7A228-C.

Original dipstick or in Ford speak "Indicator - Oil Level" for FMX automatic transmissions. Application for 1969 - 1972 Mercury Cougar and Ford Mustang with 351 and FMX automatic transmissions, code "X" on your door data plate. Sometime during 1972 Ford changed to C9AP-7A020-C. Same dip stick, but with a longer handle.Ford master part number C9OZ-7A020-A, Ford casting # C9OP-7A020-A.

Original dipstick tube, originally painted yellow and is approximately 18-3/64" inches long. Application 1971 - early 1973. Mercury Cougar or Ford Mustang with C6 automatic transmissions, code "U" on your door data plate. For any 351 or 429CJ engine. Ford master part number D1ZZ-7A228-A. *NOTE* Only used until 11-1-1972.

Original dipstick or in Ford speak "Indicator - Oil Level" for C6 automatic transmissions. Application for 1971-72 Mercury Cougar and Ford Mustang with the 351 and C6 automatic transmission, code "U" on your door data plate. Ford part # D1AF-7A020-A, Ford casting # D1AP-7A020-AB.

D1OP-7A020-AB Original dipstick or in Ford speak "Indicator - Oil Level" for C6 automatic transmissions. Application for 1971 Mercury Cougar and Ford Mustang with 429CJ and C6 automatic transmissions, code "U" on your door data plate.

Used original pan removed from a Western parts car, 14 bolt holes. This pan is not available new. These will have some dents and or scrapes. These were not painted originally, may have light rust that will clean up. Consider them Grade B used.

The only Cougar that we know came factory equipped with this part is the Cobra Jet. According to the Master Parts Catalog (MPC), any Cougar with a 3.91 or 4.11 rear end and a C-6 would have been equipped with this reducer. Replaces Ford Part #: C8ZZ-17294-A.

This clips affixes the plastic speedometer gear to the cable. Some have found that this OEM original clip fits a little better than the reproduction we offer. *Trivia* Did you know the first Cougar cast for production in 1968 was this "Custom Cougar"? This fine example was offered up on ebay summer 2008 for a mere $6500.

The only Cougar that we know came factory equipped with this part is the Cobra Jet. According to the Master Parts Catalog (MPC), any Cougar with a 3.91 or 4.11 rear end and a C-6 would have been equipped with this reducer. This is a part that we will probably never have on hand, but would love to document. If you have one of these adapters, we would be interested in being able to put detailed pictures of it on this listing. Please let us know. We hope to have a reproduction of this adapter...

Set of new bolts for attaching the floor shift bucket to the hump in the floor board, 1/4-20 bolts with washer head and 3/8 inch hex head. Sold as a set of 4 bolts. Fits all 1967 - 1973 Mercury Cougar and Ford Mustangs, and likely all of other floor shift Ford products from this time period. Check out our video on rebuilding your shifter below: ...

Used lamp diffuser for all 1969-73 Mercury Cougar and Ford Mustangs. Note the comparison picture. The reproduction is a shade or two lighter than original. The complete Ford part number is not available, the basic part number for this item is 15811. Check out our video on rebuilding your shifter below: ...

Ford called this part a 'sleeve'. Attaches to the lower shifter arm with a hitch pin. Has nice bushing, with correct nut, washer, and pin. The 1967/68 and 1969/73 versions are identical. The C1AA-7353-C sleeve has fine threads, the C9OZ-7353-A has course threads. Fits all 1967-73 Mercury Cougar and Ford Mustang, and we suspect many other Ford vehicles beginning in 1961. Check out our video on rebuilding your shifter below: ...

1969-72 Mercury Cougar and Ford Mustang shifter handle and buttons, for automatic transmissions. This is the base model shifter handle with correct black buttons, and set screws. Deluxe shifters were larger and had simulated leather wrapping. Ford part numbers C8OZ-7213-A, C8ZZ-7C488-A, and C8ZZ-7C488-B. Click on image to enlarge. Check out our video on rebuilding your shifter below: ...

Black plastic shifter bezel / indicator assembly for all 1971-73 Mercury Cougar and Ford Mustangs. Good used bezel for use with or without console or consolette. The chromed metal 1969-1970 version of this shifter cover is a very nice upgrade for 1971-1973 owners. Replaces Ford part # D1ZZ-7D443-A. Check out our video on rebuilding your shifter below: ...

Used to block light from escaping around shifter stem seal. Fits 1969-73 Mercury Cougar and Ford Mustang as well as 1971+ Pinto, Bobcat, Maverick, and Comet with floor shift automatic transmissions. The 90 degree notched portion straddles the set screw on the cast light housing. Most shifters (almost all) we see do not have this part in place any longer. Ford part number C9ZZ-7E130-A.Note: This fits perfectly on the shifters we have tried, but several customers have commented that it was too...

Adjustable rod that connects the floor shifter to the C-6 automatic transmissions. C6 transmissions only, found optionally on any 1971 Cougar. Code "U" on your door data plate tag. C-6 automatic transmission. Shift rod approximately 18 inches long. Rod originally had a "Red" paint daub for identification purposes on the Dearborn assembly line. 1971 only. Rod marked D1ZA-7340-BA.

This keeper affixes to the top of the plastic indicator arrow.  Screws included. Check out our video on rebuilding your shifter below: ...

Stunning quality and far less likely to crack than the originals. The 67 version was actually a little different than 68 - 73 but you would have to look close to see the difference. Check out our video on rebuilding your shifter below: ...

Stunning quality and far less likely to crack than the originals. The 67 version was actually a little different than 68 - 73 but you would have to look close to see the difference. Check out our video on rebuilding your shifter below: ...

Application for all 1971 - 1973 Cougars with factory C6 automatic transmission. Also the correct application for those wanting to install a small block C6 in their 1967 - 1970 Cougar. Original engine options include 351-2V, 351-4V, and 429CJ. We have found two versions of this crossmember, one with three holes in the middle section where the rubber isolator mounts and one with two. This part weighs 2.96 pounds and when set on a level surface, the height of the mounting hole on the driver side...

Good used power steering pressure line hose retainer. Mounts on top of the shock tower brace as shown. Comes as shown with used rubber insulator. Fits all 1971-73 Mercury Cougar and Ford Mustangs with V-8 engines. Ford part # D1ZZ-3C510-A.

This restored three spoke, rim blow steering wheel was used on all Cougars 1970-73 except the Cougars equipped with standard interior or on rare occasion the 1973 Cougars that came with the rare 2 spoke leather wrapped wheel. The Cougars equipped with standard interior used a two spoke wheel with the horn button located in the center pad. If you choose to send in a core for exchange it will need to be a clean one as we will not restore steering wheels that have huge cracks, severe UV damage or...