All Available Parts - 1971 Mercury Cougar

This is a complete set of four used headlight bulbs, marked with the FoMoCo logo. These sets come with two high beam and two low beam bulbs. Each bulb is tested by the electrical department. If you're trying to keep your Cougar or Mustang as close to original as possible, you should definitely grab a set.These bulbs are date coded, so if you want a particular date, be sure to mention it in the comments section of your order.  

Complete assembly with good sockets and pigtails in place. No cracks or chips, every unit is thoroughly tested.Ford Part Number: D1WB-13441-AA

Complete assembly with good sockets and pigtails in place. No cracks or chips, every unit is thoroughly tested.Ford Part Number: D1WB-13440-AA

D0OE-9425-C Cast iron intake manifold used on 1970 and 1971 C or J code 429 Super Cobra Jet engines in a Mercury Cyclone or Ford Mustang or Torino. Stock square bore 4 barrel intake manifold. Square bore is four equal venturi holes normally for Holley carburetor applications. Take off manifold with correct casting number of D0OE-9425-C. Intake shipped bare, less carburetor studs, heater tube, vacuum fittings, and water neck where applicable. Not sure of the casting date.This cast...

D0OE-9425-D Cast iron intake manifold used on all 1971 C or J code 429CJ engines in a Mercury Cougar or Ford Mustang. Stock 4 barrel intake manifold. Take off manifold with correct casting number of D0OE-9425-D. Intake shipped bare, less carburetor studs, heater tube, vacuum fittings, and water neck where applicable. This unique manifold used a General Motors Rochester Quadrajet carburetor with a spread-bore pattern. Typical after-market carburetors like Holley will not work on this intake...

Reproduction dual port vacuum advance for most all 1968-70 Ford V-8 engines. Very close replica of the factory installed vacuum advance. This version has one pressed in brass fittings for vacuum hose, and one threaded port with added vacuum fitting as shown. This working vacuum advance will need to have your threaded plug installed in the port end. OEM Ford units had gold colored bands instead of this silver band as shown. This unit very closely matches the 1968-69 vacuum advance, the later...

Set of 14 used instrument cluster sockets. These sockets are found on the backside of your instrument cluster and take a 194 bulb.

C8OZ-14A033-C Brass clip with accessory terminal for attaching the accessory lead wire with multi connector. Attaches to all 1969-70 fuse blocks found on Mercury Cougars and Ford Mustangs. Accessory feed terminal for such things as 1969 swing away steering column, rear window defogger, speed or cruise control, etc. Includes fuse block mounting hardware.

Used Autolite water temperature sending unit, fits 351C and Boss 302 engines. 260° stamped, for Mercury Cougar 1970-73, and Ford Mustang 1970-73.  Ford number D0WY-10884-A. *Note - these are specifically NOT for 1969 351W. Ford had a unique part number for that one engine.... and we don't stock that one. Sorry.Check out the video below on our new gauge tester: Check out our video on replacing the fuel system on a '68 Cougar! ...

Used Autolite water temperature sending unit, fits 1970 351W-2V, 428CJ, and 429CJ engines. 258° stamped, for Mercury Cougar 1970-73, and Ford Mustang 1970-73.  Ford number D0ZZ-10884-A. *Note - these are specifically NOT for 1969 351W. Ford had a unique part number for that one engine.... and we don't stock that one. Sorry.Check out the video below on our new gauge tester: Check out our video on replacing the fuel system on a '68 Cougar! ...

Reproduction battery powered  (AA battery) scratch built clock. Great alternative for those without a core for rebuild. American made reproduction console clock. Adjustment to clock is made from the reverse side of the clock, there is no stem through the lens for adjustment. Illumination of the dial is through the factory harness. Includes new lens and battery. No Core Required! Quartz movement clocks have second hands that click around, original clocks had a constant sweep...

Used Autolite water temperature sending unit, fits 1969 Mercury Cougar and Ford Mustang with 351W-2V, 351W-2V engines. Ford number C9WY-10884-A.Check out the video below on our new gauge tester: Check out our video on replacing the fuel system on a '68 Cougar! ...

Reproduction hold down clamp rivet for the 67 - 73 Cougar or Mustang. This rivet holds the clip / clamp onto the distributor. Sold individually, 2 per car.

Used distributor for the Mercury Cougar or Ford Mustang that is equipped with the 351 Cleveland 2V engine.

Used core distributor for 1970 Mercury Cougar and Ford Mustang with M code 351C-4V and either 3 or 4 speed manual transmission. Core distributors will have correct stamping of D0OF-V. Original Ford part number D0OF-12127-V. 351 Windsor engines use a smaller distributor gear (about 1-1/4"), Cleveland.distributor gear is about 1-7/16" in diameter.

Used Distributor / 351C-2V for the 1971 Mercury Cougar / 1971 Ford MustangFord part number  D1OF-12127-GA   

Used Distributor / 351C-2V for the 1971 Mercury Cougar / 1971 Ford Mustang Ford part number  D1OF-12127-PA  

Used Distributor / 351C-2V for the 1971 Mercury Cougar / 1971 Ford Mustang Ford part number D0OF-12127-U  

Used Distributor / 351C-4V for the 1971 Mercury Cougar / 1971 Ford MustangFord part numbher D1OF-12127-LA  

Used Distributor / 351C-4V for the 1971 Mercury Cougar / 1971 Ford Mustang Ford part number D0OF-12127-G    

Used Distributor / 429CJ for the 1971 Mercury Cougar / 1971 Ford MustangFord part number D1AF-12127-NA  

Used Distributor / 429CJ for the 1971 Mercury Cougar / 1971 Ford Mustang / Torino Ford part number D0OF-12127-AA Current listing has a date of 0F26 or June 26, 1970. 

NOTE: WE SUGGEST LOCAL PICK UP ONLY FOR CORE ENGINE BLOCKS BECAUSE WE CANNOT GUARANTEE BLOCKS WILL NOT HAVE CRACKS INTERNALLY.Used standard bore 4.00" Ford 351C 1971-73 engine block. Will be used, dirty, have measurable taper, and will have a ridge. Good for rebuild. Bare block, may have D0AE, D2AE, castings. When we have them in stock we will post the casting date or dates. Heavy, will require either local pickup or freight shipping. Dated 2C7 or March 7, 1972. D2AE-6015-CA.This item...

We have a very difficult time keeping grade "A" tail light lenses in stock. This lens is prone to cracking in between the clear and red portion of the lens. Let us know if you have extras to sell or trade! *NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's and is the designer of all of our solid state sequential systems. There is no question he cannot answer! Here is a link to...

We have a very difficult time keeping grade "A" 1971-72 tail light lenses in stock. Let us know if you have extras to sell or trade! Replaces Ford part # D1WY-13450-B.

This one piece lens was used only on the XR7 model Cougar from 1971 - 1973. This lens will not be cracked or overly "milky" looking from over exposure to the sun. This lens will need to be hand polished to get the fine scratches out. Check out this video

Used battery tray, may not be exactly like the assembly line tray. Group 27 battery tray is typical for cars with air conditioning and higher amp alternators. Fits 1971-73 Mercury Cougar and Ford Mustang. Also 1970-71 Ford Torino and Mercury Cyclone and variants of the B or C midsize Ford and Mercury bodied cars. Used condition, minor pitting as shown. Replaces Ford Part #: D0OZ-10732-B.

Used Wire lead for the accessory terminal found optionally on 71 - 73 Mercury Cougar and Ford Mustang fuse blocks. Lead comes with factory molded triple female connector for plugging in the various accessories such as 1969 swing away steering column, rear window defogger, speed or cruise control, etc. Wire will be marked with D1AB-14A318-AB

C8OZ-14A033-C Brass clip with accessory terminal for attaching the accessory lead wire with multi connector. Missing attaching screw and nut. Attaches to all 1969-73 fuse blocks found on Mercury Cougars and Ford Mustangs. Accessory feed terminal for such things as 1969 swing away steering column, rear window defogger, speed or cruise control, etc. Includes fuse block mounting hardware.*Note - Naked, no machine screw and nut for mounting to fuse block. 

The following excerpt was taken from the advance summary sheets mailed to dealers in 66 and 67.- "For when your customer feels like putting his foot down! Cougar has got a heart of "GO" - just as it comes from the factory. But there are bound to be buyers who will get under the hood to sharpen Cougar's claws. To satisfy the needs of these high performance buffs, here are a number of performance equipment items designed especially for Cougar by Shelby American, Inc. We suggest you stock a...

These are original amp meters converted from reading amps to reading volts. Includes new matching XR7 overlay made from top quality 3M 467MP and use 200MP adhesive. The longer 200MP adhesive is in place the stronger it binds.  Click here for a article describing the advantages of a Volt Meter.

Each of these great kits include all three required cables, including part numbers, proper terminal and post clamp ends. Starter cables are properly shielded from heat. 1970-71 Mercury Cougar with 65-75 AMP alternators and V-8 engines. The originals were either 43-55 Amp (Standard) Draw or 65-75 Amp (High) Draw. We recommend going with the High Draw. As one customer put it, "These [standard draw cables] look anemic." (Thanks for the feedback Charles!) Replaces Ford Part # : D0ZZ-14300 ...

Mint condition part that is almost always missing on cars equipped with group 27 battery. Great addition to your 1970 BOSS 302 Eliminator. Also correct for Mustang and Torino. Ford part # D0OZ-10A682-A, casting number as seen on part is D0OB-10A682-A. There is currently no correct reproduction of this part. Click here for more information on this rare part.

C3OZ-1126-B Used brake drum with the vintage casting look. Guaranteed to successfully be turned and not exceed the manufacturers inside maximum of 10.060". When we say the "vintage casting look", we mean with the proper groove and contours. Reproductions are fine, but do not retain the casting design of the original casting company. When looking for used brake drums, the rule of thumb is to find ones with a brake surface area of 1/4 inch more than the brake shoe width.

C9OZ-2211-B Right hand rear brake backing plate for use with 2 inch wide brake shoes. Clean Western part with no heavy corrosion like you see on Eastern cars. Inspected for excessive wear. Used on cars with 10" drums.Originally manufactured by Kelsey-Hayes, KH part number 71085. Originally manufactured by Bendix, part number 317559.

C9OZ-2212-B Left hand rear brake backing plate for use with 2 inch wide brake shoes. Clean Western part with no heavy corrosion like you see on Eastern cars. Inspected for excessive wear. Used on cars with 10" drums.Originally manufactured by Kelsey-Hayes, KH part number 71086. Originally manufactured by Bendix, part number 317558..

This used emergency / parking brake cable connector is for the Mercury Cougar only. That is because it is longer than the Mustang version due to the Cougar's longer wheelbase. This connector connects the two ball ends of the long and short emergency brake cables. Ford part # C7WY-2A790-A.

New old stock emergency / parking brake pedal pad that features all stainless steel construction. Fits any 1969-73 Mercury Cougar and Ford Mustang.Replaces Ford part # C9ZZ-2A487-C.

This is the 100% correct Ford original battery hold down clamp. Stamped with D0OB10755A. Ford Part #: D0OZ-10718-B. Note: The battery hold down clamp offered by many Mustang / Cougar vendors as "Concours Correct" is actually for the 1974 - 1978 Cougar /  Mustang.

Used grade "A" emergency / parking brake release handle with bezel and cable for the Mercury Cougar. This unit fits both the Standard and XR7. Our grade "A" part will have a good cable sheath and the chrome on the release handle will be very nice, but not perfect. Ford Part Number: D1WY-2760-A or D1WY-2A760-A This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit of 50% of our web...

Used brake shoe guide plate, or anchor pin, that holds the top of the drum brake shoes together on your Mercury Cougar or Ford Mustang equipped with drum brakes. For the money our reproduction plate is a better value and cleaner, too. These have 1/2 inch holes in them.Replaces Ford part number C4UZ-2028-A.

Used passenger side (right hand) sunroof cable for the Mercury Cougar. We have a really hard time keeping these units in stock. Keep in mind this same basic cable design was used on many makes including Porsche, BMW, Mercedes and several other cars through the early 1980's. The same basic design (minor changes through the years) was used on Lincolns, Thunderbirds and other Ford products through the mid seventies. We are buyers of used sunroof cables, motors and misc parts so keep us in mind...

Used driver side (left hand) sunroof cable for the Mercury Cougar. We have a really hard time keeping these units in stock. Keep in mind this same basic cable design was used on many makes including Porsche, BMW, Mercedes and several other cars through the early 1980's. The same basic design (minor changes through the years) was used on Lincolns, Thunderbirds and other Ford products through the mid seventies. We are buyers of used sunroof cables, motors and misc parts so keep us in mind you...

This reproduction emergency / parking brake idler bracket welds to the under side of the floor on the driver side (left hand) of the vehicle and has the factory spec pin.

This passenger side (right hand) reproduction emergency / parking brake cable idler bracket mounts to the right front floor pan. The idler bracket is often discarded when the floor pan is removed for replacement. We also have good used units in stock for those that desire 100% correctness.

Reproduction brake shoe guide plate, or anchor pin, that holds the top of the drum brake shoes together on your Mercury Cougar or Ford Mustang equipped with drum brakes. These have 1/2 inch holes in them, like the originals.Replaces Ford part number C4UZ-2028-A.

Used hairpin clip for attaching the brake light switch to the brake pedal. This clip was also used to attach the clutch rod to the clutch pedal on manual transmission cars. Fits all years 1967-73, Ford and Mercury.Ford Part # 380699-S

Steel tubing features tin/lead coating and plated zinc chromate fitting and are exact copies of the originals with color coded fittings.

Used inner and outer driver side (left hand) wheel house as cut from a 1971-73 Mercury Cougar parts car. This is a hard part for us to obtain as we have to sacrifice all surrounding parts to remove it in its entirety. The almost always will have a substantial amount of rust showing at the very tips of the outers where they end behind the wheel. If you want to save shipping costs we can sacrifice the inner wheel house and sell you only the outer portion. Used inner and outer driver side...

Crating Fee Applies To This Item. You will be contacted once your order is reviewed to discuss the crating fee. Crating fees generally run between $175 - $250 (this does not include truck freight charges). If an item has a crating fee, this usually indicates that it must ship via Truck Freight and can only be shipped to US addresses and select Canadian addresses. Since we never have all years and sides in stock at any given time in Grade "A" form, and since almost every panel has "some" minor...

Our grade "A" fenders are truly what you would expect from an "A" rated part! We never get returns on our grade "A" fenders which is very important considering the shipping costs involved. Grade "A" fenders have no rust or excessive filler and nothing more than dings or light scrapes for damage. When you turn it over you will not see anything more than light surface rust, no distorted wheel lip areas from over sized tires. We really inspect the area where the fender extension bolts on well as...

Rust free with no prior damage. Cut with a plasma cutter well above the style line from a solid Western fender. Generally we cut these about 14" up but you can have it cut anywhere you wish and the price remains the same, only the shipping increases.

Used original FoMoCo upper cowl cut for all 1971-73 Mercury Cougars and Ford Mustangs without A/C. Bear in mind that the inner metal section, or the undersides, did not get paint and is the upper cowl section as shown. A/C cars differ, they have a fresh air duct arrangement. Note that this part will not be perfect and will require hours of spot weld removal due to how large we cut them. The shipping will also be much more than our repro. We highly suggest buying the repro as it is a direct...

Used original FoMoCo upper cowl cut for all 1971-73 Mercury Cougars and Ford Mustangs with A/C. Bear in mind that the inner metal section, or the undersides, did not get paint and is the upper cowl section as shown. A/C cars differ, they have a fresh air duct arrangement. Note that this part will not be perfect and will require hours of spot weld removal due to how large we cut them. The shipping will also be much more than our repro. We highly suggest buying the repro as you can easily modify...

New Old Stock rear valance for the 71 - 73 Cougar. Original Ford is the best way to go whenever you can.Ford part # D1WY-6540544-A.

Reproduction passenger side (right hand) outer frame rail patch for the Mercury Cougar and Ford Mustang. The outer rail has weld nuts installed for proper installation.

Complete roof cut that includes the rear window opening and package tray. These roofs may or may not have the holes drilled for a vinyl top. If you have doubts of whether or not you need a roof with or without a rear window, we suggest that you remove your rear glass and peel back your vinyl roof and inspect the lower channel where the rear windshield rests and the section of steel covered by the vinyl material. A 1967 non-vinyl top roof with package tray is pictured. We want you to keep...

Roof cut that includes the roof skin, 'A' pillars cut about 4 inches from the top, rear or 'C' pillars cut below the leaded seam. We have plenty of inexpensive, damage free roofs that have never had a vinyl top installed. If you want the pillars intact this triples the size of the crate and makes it cost prohibitive in most cases. Longer cuts with long extended pillars add greatly to the cost of shipping. This is a perfect cut for a Cougar owner looking to replace their roof skin. We do not...

Our grade "A" fenders are truly what you would expect from an "A" rated part! We never get returns on our grade "A" fenders which is very important considering the shipping costs involved. Grade "A" fenders have no rust or excessive filler and nothing more than dings or light scrapes for damage. When you turn it over you will not see anything more than light surface rust, no distorted wheel lip areas from over sized tires. We really inspect the area where the fender extension bolts on well as...

Crating Fee Applies To This Item. You will be contacted once your order is reviewed to discuss the crating fee. Crating fees generally run between $175 - $250 (this does not include truck freight charges). If an item has a crating fee, this usually indicates that it must ship via Truck Freight and can only be shipped to US addresses and select Canadian addresses. Since we never have all years and sides in stock at any given time in Grade "A" form and since almost every panel has "some" minor...

Crating Fee Applies To This Item. You will be contacted once your order is reviewed to discuss the crating fee. Crating fees generally run between $175 - $250 (this does not include truck freight charges). If an item has a crating fee, this usually indicates that it must ship via Truck Freight and can only be shipped to US addresses and select Canadian addresses. Our used driver side grade "B" quarter panels are still good panels, but will need more body work than the Grade "A" panels, due to...

Crating Fee Applies To This Item. You will be contacted once your order is reviewed to discuss the crating fee. Crating fees generally run between $175 - $250 (this does not include truck freight charges). If an item has a crating fee, this usually indicates that it must ship via Truck Freight and can only be shipped to US addresses and select Canadian addresses. Our used passenger (right hand) side grade "B" quarter panels are still good panels, but will need more body work than the Grade "A"...

Grade "A" doors have never been dented in, cracked in the door latch area or rusted in the corners under the weatherstrip. When you turn it over and inspect it, the bottom seam it is not expanding from the inside out due to rust. There are no drilled holes for an after market impact strip and the sound deadener is usually still intact. Often times it will still bear the original paint but do expect multiple, small door dings. This is the best condition Western door you could ever hope to find,...

Good used, rust free valance. Getting to be hard to find without excessive filler or severe damage. We have a local body man take small dents out and he does not load them up with Bondo. He removes the filler and works the dent out properly. These are not paint ready, flawless parts but rather 40 years old, taken from a parts car. We do have NOS and on occasion we we get in a flawless used example. We have no plans to start selling the fiberglass reproductions as we feel good used, original...

Driver side convertible frame assembly mounting and pivot bracket for all 1971-73 Mercury Cougar and Ford Mustang. Does not include the hydraulic cylinder bracket, cylinder mounting bracket sold separately. Bushings, bolts, and specialty fasteners not included. Mounts behind the quarter interior panel.  Ford part number D1ZZ-7653119-A.

Passenger side convertible frame assembly mounting and pivot bracket for all 1971-73 Mercury Cougar and Ford Mustang. Does not include the hydraulic cylinder bracket, cylinder mounting bracket sold separately. Bushings, bolts, and specialty fasteners not included. Mounts behind the quarter interior panel.  Ford part number D1ZZ-7653118-A.

This is an extremely rare hood scoop found only on the 71-72 GT and 1971 429 Cougars. This is similar to the 1969-70 scoop, but tapers more in the front so as to follow the unique hood line of the 1971-73 Cougar.Ford part # D1WB-16C664-AA. ...

Now you can replace this original part, which is commonly stripped out, with a nice reproduction. Must be welded to floor pan. 6 total per car, 2 inboard in the transmission tunnel, and 4 on the rear seat pans. The front outboard anchors are part of the rocker rails. Rectangular shaped like the 1967-73 cars. We have noticed that the last generation 1971-73 Cougars had 4 round shaped plates in the rear floors. Same threads, all work the same. These were pretty much used on all Ford...

Stamped steel floor pan drain caps used to plug oval holes in the front or rear floors. Economy grade reproduction floor pan plug that closely resembling the originals. Complete with rough stampings made from galvanized steel.

Passenger side (right hand) front seat floor pan. This pan is cut from the full floor pans in order to save on shipping costs when a customer does not need the entire length pan. Cutting from the Dynacorn full length pans means this will be a quality cut, when compared to other pans on the market.   1967-68 style ribbing, works in 1969-70 and can be modified to fit 1971-73. *NOTE* This floor pan has the outside lip bent down which is proper for coupes, convertibles were bent up....

1971-72 Mercury Cougar convertible driver side. Our grade "A" rear quarter panel extensions have no obvious dings, scrapes, bumper contact damage or warping due to over tightening of the mounting studs. Please choose which side and year you need. There are very slight differences on 1973 and they do carry different part numbers. Ford casting # D1WB-7628519, Mercury MPC # D1WY-7628011-A. Do you have questions about your Cat's factory pinstriping? This link may help. ...

1971-72 Mercury Cougar convertible passenger side. Our grade "A" rear quarter panel extensions have no obvious dings, scrapes, bumper contact damage or warping due to over tightening of the mounting studs. Please choose which side and year you need. There are very slight differences on 1973 and they do carry different part numbers. Ford casting number D1WB-7628518, Mercury MPC number D1WY-7628010-A. Do you have questions about your Cat's factory pinstriping? This link may help. ...

Good reproduction reinforcing plate, contours are like the C5ZZ-7610962-A plate which was used through 1970. Thick steel like the originals, and with same contours. Bolts to the left hand and right hand lower floor reinforcement panels. Bolts into place with 6 hex bolts 3/8-16 x 1-1/8" with washers. These were painted satin black from the factory. Replaces Ford Part # C5ZZ-7610962-A. The Ford description of this plate is "Plate - Front floor lower cross member". All 1969 - 1973...

Restored show quality passenger side (right hand) horizontal quarter window moulding / trim. They were used in conjunction with the door trim on XR7 models only. Located at the base of the quarter window and mounted horizontally on XR7 convertible models only. Due to the difficulty in obtaining trim we no longer sell these without first having you send us your cores. ...

This driver side moulding is correct for convertible. On convertibles the top portion is trimmed to allow it to slide under the sun visor bracket. The engineering number imprinted on the back is D1ZB-6503599 for 1971-1972 and D3ZB-6503599 for 1973. Convertibles show the same casting numbers on the part, but are a modified before assembly. We do have factory cut convertible mouldings both early and late. Ford part # D1ZZ-7603599, D1ZB-6503599-aw, D3ZZ-7603599, D3ZB-6503599-aw *NOTE* Excludes...

Used passenger side (right hand) convertible top boot trim moulding / trim for the Mercury Cougar convertible. If it were not for the paint over-spray on the black stripe of the drivers side piece these would be ready to bolt on and go! This is the best used example we have ever had in stock. We have several sets in stock with moderate to heavy pitting that are reasonably priced. Ford casting number reads D1WB-76423A18-AA or D1WY-76423A18-A. *Note - This item is not correct for a Ford Mustang. ...

This is the "Chrome" trim across the top of the windshield on the inside. This piece will need to be sandblasted and repainted. Many people have chromed these, but because of Federal safety regulations from the factory they were painted satin silver.Ford Part Number: D1ZZ-7603606-A.

Detachable mounting plate for installing the convertible ram cylinder to the convertible top frame assembly behind the quarter interior panel. Right and left are the same, fits all 1971-73 Mercury Cougar and Ford Mustang convertibles. Ford part number D1ZZ-76531A19-A.

We have found a new manufacturer of the convertible top boots that are supposed to fit much better than the boots we were previously selling. See Pics Below. Ford calls this part the "folding top dust hood". Made from original pattern. Features long lasting vinyl. Includes foam pads. We stock the black and white. All other colors are ordered on demand from the manufacturer. Please note that convertible boots never came from the factory with snaps (except the 6 on the interior panels), so any...

We have found a new manufacturer of the convertible top boots that are supposed to fit much better than the boots we were previously selling. See Pics Below. Ford calls this part the "folding top dust hood". Made from original pattern. Features long lasting vinyl. Includes foam pads. We stock the black and white. All other colors are ordered on demand from the manufacturer. Please note that convertible boots never came from the factory with snaps (except the 6 on the interior panels), so any...

This pair of reproduction convertible top hooks are beautifully chrome plated and features correct thread size. Looks close to original. These hooks are actually for 71 - 73 Cougars and Mustangs, but will work just fine on the 69 - 70.

These restored show quality mouldings are sold as a pair (driver and passenger side). They were used in conjunction with the door trim on XR7 models only. Located at the base of the quarter window and mounted horizontally on XR7 convertible models only. Due to the difficulty in obtaining trim we no longer sell these without first having you send us your cores. ...

C5ZZ-7610962-A Ford description of this plate is "Plate - Front floor lower cross member". All 1967-73 Cougar convertibles and all 1965-73 Ford Mustang convertibles use this plate. Bolts into place with 6 hex bolts 3/8-16 x 1-1/8" with washers. These were painted satin black from the factory. As you look at our picture below you will see the repro is about half the thickness. The repro is different in every detail but will work. We also have used plates with minor damage at a reduced cost.

D1AZ-9A603-A Metal shroud for all 1971 351 engines including H code 351-2V and M code 351-4V. One piece design uses a paper and aluminum tube to bridge to the air cleaner snorkel.

D1AZ-9A603-C Metal shroud for all 1971 429 Cobra Jet engines including C code 429CJ non-ram air and J code 429 CJ with ram air. One piece design uses a paper and aluminum tube to bridge to the air cleaner snorkel. This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit of 50% of our web price for parts delivered in hand or by carrier to our Brooks, Oregon location. If you're not interested...

Application would be for only 1971 Cougars with the 429CJ option, either ram air or non-ram air. Original Ford part number is D0GY-9A626-A.  Also used on the Torino / Cyclone / Cobra / Ranchero.  Notice the main difference between this genuine CJ snorkel and the "Economy" truck snorkel we have listed is the mounting flange hole placement and contour. Click on images to enlarge. ...

Fits all V8s with oval air cleaner.

This engine compartment lamp assembly includes lamp socket, bracket, mercury switch, and length of wire. *NOTE* This unit was used on Cougars and Mustangs produced before 12/15/1971.Replaces part # D1ZZ-15702-A

Older used aluminum intake manifold. Port size is for the 2V cylinder heads. Perfect for adding a 4 barrel carburetor to a stock 351 Cleveland 2V engine.

Lightly used intake manifold cast aluminum 427-4V medium riser. Blue Thunder casting 427MR-4V. Has the oil fill tube in front, dual plane, and the road draft provision in the back. Very tall manifold, likely to not fit under the stock hood of a Cougar or Mustang. Do your research on this, if you know, you know. We don't. Small portion on the driver side front has been lightly ground down, likely for a coil. No other issues noted. 

Adapter tube for connecting the fuel vapor purge tube to the air cleaner base. Can be either blue or black in color.

Will require trimming to fit your year application. Note that 1967 has the three raised enforcements facing the inside of the trunk and 1969-73 the raised portions face outward. Thus you will want this panel for the passengers side of those series. Check out this video

Will require trimming to fit your year application. Note that 1967 has the three raised enforcements facing the inside of the trunk and 1969-73 the raised portions face outward, Thus you will want this panel for the drivers side of those series.  Check out this video

High quality, durable canvas cap with velcro closure. The hat now features our Web address on the back! "The baseball cap arrived Saturday but since I wasn't home, they didn't leave it for me. I picked it up today at the post office. It's real nice! Seems to be a higher quality cap compared to others I've worn. Thanks for sending it." Larry Check out this video of our 2013 Open House event! ...

The Hustler Stick features heavy-duty 1-1/4" diameter tubing, and is an alignment bar designed for bumpers, hoods, decks, panels etc. Made in the USA, it has a 1/4", 6 foot long chain with hooks at each end. This versatile tool is very useful in shaping damages on a vehicle body. To use it, hook it up to the panel or bumper, anchor the stick properly, and pull it by hand.We will loan this hustler stick for 60 days, with a 100% refundable purchase price. Tool must be returned in undamaged...

Here is another great product form Permatex. This decal and adhesive remover removes bumper and window stickers, tar, sap, bugs and other gooey substances. 

New intake manifold that has never been used, but it's missing the packaging, so we're calling it an "out of box special". Port size is for the 2V cylinder heads. Perfect for adding a 4 barrel carburetor to a stock 351 Cleveland 2V engine.

Original used plastic upper radiator seal for 1971-73 Mercury Cougar and Ford Mustang with 26 inch radiators. Also called a radiator air deflector. Also fits 1970-71 Torino, Ranchero, Cyclone and Montego. As well as 1970-72 full sized Ford and Mercury cars. Comes with 4 original spring clips for mounting. Clips are not sold separately. Plastic portion originally measured 23-13/16 inches long.  Replaces Ford part number D0OB-8B170-B.

This is the correct, original gasket for your 1971-73 Mercury Cougar antenna. Not only is it much thicker than the Ford Mustang gasket, but it also has a different overall geometry to it. Gasket mounts under the antenna base, The Mustang gasket will work, but your antenna will always be slightly askew. Unfortunately the high quality reproduction antenna we offer is only available from the manufacturer with a reproduction Ford Mustang gasket. Please remember not to discard your original Cougar...

Round ring shaped gasket that goes on top of the carburetor. Protects and seals the carburetor to the air cleaner.New Old Stock Ford gasket, Ford part number C5ZZ-9654-B.