All Available Parts - 1971 Mercury Cougar

Used jumper wire for connecting the heated back lite glass to the defog harness on any 1971-72 Mercury Cougar or Ford Mustang equipped with factory rear defogger. AKA defrost. 1973 has a different wire connector.Ford part number found on wiring diagram 18C394.

Used replacement toggle switch for the 71-73 Cougar XR7. This is a double throw switch that can be used in either the accessory, convertible top or defog positions on the switch assembly.

Used replacement toggle switch for the 71-73 Cougar XR7. This is a single throw switch that can be used in either the map or courtesy light positions on the switch assembly.

Used timing chain cover for any 351C or Cleveland engine from 1970-74. Mercury Cougar and Ford Mustang and additionally fits 351M / 400M engines. All steel construction without excessive rust or damage. Installation bolt kits also avialable.Replaces Ford part number D0AZ-6B070-A.*Note - will not fit 351W or Windsor engines.

Constructed from corrosion resistant copper and brass. Quality replacement part for a job you do not have to do again anytime soon. Replaces Ford Part #: C9ZZ-18476-B. Check out our videos below on how to replace a heater core! We now have separate videos for the first generation ('67-'68) and second generation ('69-'70). ...

This unit mounts on the main air chamber, it opens and closes the air vent. Made of nylon with a brass plunger. This unit is easy to test and can be seen by removing the glove box. Often it is the internal spring that fails on these and if your Cougar or Mustang will not easily change between blowing through the defrost ducts and the floor duct, this unit may be the culprit. Switch assembly, servo control. Replaces Ford part # C6OZ-18C311-A. *NOTE* You will need to retain your mounting bracket...

Special steel clamps that hold both halves of the heater box together on both A/C and non A/C Cougars and Mustangs. Two versions found, round and flat, like in the comparison with reproduction. Sold individually. This taller or round clip is slightly easier to clip onto the boxes. Replaces part #: C0DF-19A779-A. *NOTE* Never pry these off or the lip they attach to will lose the edge and it will be hard to fasten the clips back in place. They are designed to come off by inserting a standard...

These are getting so hard to find without a broken drain cock or rust in the metal lips. The unit pictured here is typical of what you can expect when you buy out used complete box. Plan on repairing the drain cock or other minor cracks. All doors will be functional, we will not promise the evaporator is good and we do promise the heater core will be bad. We have a few single halves if you need the half without the drain cock. Soon we will have every single internal and external part from this...

Reproduction A/C evaporator for your Mercury Cougar or Ford Mustang.*Note - We have had numerous customers complain that these don't fit exactly like the originals.As far as evaporators go, we highly suggest going with a good used evaporator over these new versions. What happens is this: These companies use more coils (35% more passes) which equals out to thinner metal, which also equals out to performance that's sub-par to a good used original evaporator.Click on images to enlarge. ...

Used OEM Ford heater blower motor resistor for cars with factory installed air conditioning, it attaches to the A/C blower fiberglass housing. Fits all 1969-73 Mercury Cougar and Ford Mustang with integral or factory air conditioning. The reproduction resistor that fits the 1967 - 1968 Cougar and 1965-1968 Mustang has a different hole pattern. According to manufacturer information (INDAK), the OHM output for this switch makes it incompatible with the earlier reproduction resistor. We inspect...

New heater blower motor resistor that attaches to the heater blower fiberglass housing. Ford part # C8OZ-18591-A.1970 and Later Maverick and Comet1971 and Later Lincoln

Good used grommet that seals the heater hoses and A/C lines where they pass through the firewall on the passenger side. Made from a spongy rubber, attaches to the heater core and seals the firewall from the inside. This grommet does not use a retaining bracket like previous years. Will be intact, but will show some degradation as shown in the picture, most evident where the heater core tubes pass through. Engineering # D1ZZ-19B588-A.

Used air conditioning evaporator core for 1971-73. We only sell used coils that are clean and sealed and do not sell coils that have pest damage or have corrosion from a leaking heater core. Even though we stand behind these used units for 30 days, we still suggest that you pressure test them before installing as we all know what kind of labor is required to install one of these. 1971-73 evaporators have 2 male fillings, and the whole unit is made of aluminum, including the tubes.Ford part #...

Usually ships in 3-5 business days. Reproduction heater box for the Mercury Cougar or Ford Mustang equipped with air conditioning. These are getting so hard to find without a broken drain cock or rust in the metal lips, so we are happy to bring you this quality reproduction! This unit will come with all the necessary seals and clips. If you need to replace them you can get the heater core here or the blower motor here. We suggest reusing your original A/C evaporator as long as it doesn't leak...

Used heater blower motor for Mercury Cougars and Ford Mustangs with integral or factory air conditioning. These are good used original FoMoCo units and have the correct pigtails in place. This used unit also carries a one year warranty compared to the reproduction that carries a 30 day warranty. The mounting plate is included and mounted to the motor. On the reproduction units, the mounting plates are sold separately. These are the 1971-73 variety, which have specific colored wires and leads....

Used air conditioning thermostat switch for any 1971-73 Mercury Cougar or Ford Mustang with integral or factory A/C. Attaches to the side of the fiberglass box under the dash, the wire probe gets inserted into the evaporator. Tested and working switch. These were originally manufactured by Cutler-Hammer for Ford. Ford part numbers D1ZA-19618-A or D1ZZ-19618-A.

Blower door for any 1967-73 Mercury Cougar or Ford Mustang with factory or integral air conditioning. The blower door allows air to pass to the duct tubes from the center blower motor housing. Part cleaned for photograph, normally will ship 'as removed'. Inspected for excessive rust pitting or weakness of the metal, will have good rubber seal as shown. Door only, shaft not included, but available. See related parts.Replaces Ford part number C7ZZ-18B254-A.

Shaft or rod for the A/C damper blower door on any 1969-73 Mercury Cougar or Ford Mustang with factory or integral air conditioning. 1969-73 shaft is clocked differently than the 1967-68 version. This air conditioning damper door is in front of the blower or fan in the center of the car. Part cleaned for photograph, normally will ship 'as removed'. Inspected for damage or weakness of the metal. Shaft only, door not included, but available. See related parts.Replaces Ford part number...

Special steel clamps that hold both halves of the heater box together. Fully functional, but is different than the original. Replaces Ford Part #: C0DF-19A779-A. *NOTE* Never pry these off or the lip they attach to will lose the edge and it will be hard to fasten the clips back in place. They are designed to come off by inserting a standard screw driver in one of the ends and flexing the clamp to open the jaws.

Reproduction vacuum actuator for controlling dampers and levers on the different year A/C boxes. These came in several different anodized colors. This is the basic valve with a single vacuum port.

Special steel clamps that hold both halves of the heater box together on both A/C and non A/C Cougars and Mustangs. Two versions found, round and flat, like in the comparison with reproduction. Sold individually. Replaces part #: C0DF-19A779-A. *NOTE* Never pry these off or the lip they attach to will lose the edge and it will be hard to fasten the clips back in place. They are designed to come off by inserting a standard screw driver in one of the ends and flexing the clamp to open the jaws. ...

Air conditioning fan blower assembly for any 1971-73 Mercury Cougar or Ford Mustang with factory A/C. We offer this assembly to go along with the reproduction heater box with air conditioning. Assembly comes as shown: fiberglass housing, fan motor, fan motor mounting plate, fan wheel, fan motor resistor, and the one attached vacuum actuating valve. All components tested and working, housing used and may have a chip or small crack from 5 decades of use.

Set of 4 special steel clamps that hold both halves of the heater box together. Fully functional, but is different than the original. Replaces Ford Part #: C0DF-19A779-A. *NOTE* Never pry these off or the lip they attach to will lose the edge and it will be hard to fasten the clips back in place. They are designed to come off by inserting a standard screw driver in one of the ends and flexing the clamp to open the jaws.

Used mounting bracket from a 1971-73 Mercury Cougar or Ford Mustang with factory installed air conditioning. This is the tab that is riveted to the blower housing, the stud goes through the firewall. Bracket with stud only, no other hardware included. Normally this will ship with the old fiberglass remnants still riveted to this bracket. 

For Mercury Cougar and Ford Mustangs with integral or factory installed air conditioning with any V-8 engine. Original condensation drain hose from the A/C case, through the floor board, to the ground. Correct "S" shaped moulded hose with restrictor intact. Almost the same hose as was used 1969-70, Dearborn assembly line hoses have a ribbed section 1971-73. The 1969-70 versions, typically have the alligator texture on the outside of the hose.  Ford part # C9ZZ-19858. ...

Air conditioning fan blower BARE clam shell assembly for any 1971-73 Mercury Cougar or Ford Mustang with factory A/C. Assembly comes as shown: fiberglass two piece housing, flapper door, and a couple of clips to hold it together. Grade B used will have a minor stress crack, and or small chips. The holes for attaching duct work also may have one hole blown out. See Grade A for a better condition version.

Air conditioning fan blower BARE clam shell assembly for any 1971-73 Mercury Cougar or Ford Mustang with factory A/C. Assembly comes as shown: fiberglass two piece housing, flapper door, and a couple of clips to hold it together. Grade B used will have a minor stress crack, and or small chips. The holes for attaching duct work also may have one hole blown out. See Grade A for a better condition version.

Used vacuum actuator for controlling dampers and levers on the different year A/C boxes. This is a bare vacuum valve, that does not have the screwed on extension which make the unique part numbers from the Ford MPC. Tested and holds vacuum. These came in several different anodized colors. All bare sheet metal steel construction starting in 1971 until 1973. This is the basic valve with a single vacuum port. There are other versions with an extra vacuum port on the side.

Used extension or rod for the vacuum actuator for controlling the air restrictor door on the 1969-73 Mercury Cougar or Ford Mustang factory integral A/C boxes. This gets screwed onto the tab on the vacuum actuator, which make the unique part numbers from the Ford MPC. About 6 inches long. For 1969-73 Cougar and Mustang, has a dog leg jog as shown. On the front of the A/C plenum. Vacuum actuator sold separately, see related items. Stamped with Ford casting number C9ZA-18...

Used extension or rod for the vacuum actuator for controlling the fresh air door on the 1969-73 Mercury Cougar or Ford Mustang factory integral A/C boxes. This gets screwed onto the tab on the vacuum actuator, which make the unique part numbers from the Ford MPC. About 6 inches long. For 1969-73 Cougar and Mustang, has a dog leg jog as shown. On the right hand end, of the A/C plenum. Vacuum actuator sold separately, see related items. Stamped with Ford casting...

Concours correct heater hose for all Cougars and Mustangs built after 2/1/1970. Prior to that year, red striping was used. These hoses feature durable yellow striping, "Autolite" spelled out, and are dated LQ0H04A. Correct for all V-8 engines WITHOUT air conditioning. The hoses that are used on cars with A/C have a molded 90 degree elbow at the end that fits on the water valve side. Some length trimming may be required for a tight looking fit. Turn those hoses so that the yellow striping...

Concours correct yellow striped heater hose for Cougars and Mustangs WITH factory or integral air conditioning. These hoses feature durable yellow striping with "Autolite" spelled out and dated LQ0H04A. Correct for all V-8 engines with A/C. The hoses feature a correctly molded 90 degree elbow that fits on the water valve side. Some length trimming may be required for a tight looking fit. Turn those hoses so that the yellow striping shows! Replaces part # D1ZZ-18472-ACY ...

Reproduction heater blower motor for Mercury Cougar and Ford Mustang. Wiring will need to be spliced into your existing wiring harness. Save the squirrel cage and the heater motor mounting plate from your old unit because it is not included with this item.These off-shore units may or may not prove to be as good of value as our good used original FoMoCo reconditioned units. Notice they do not have the correct pigtails in place. To date, all we can find for these cars are foreign made units....

Reproduction heater blower motor for Mercury Cougars and Ford Mustangs with integral or factory air conditioning. These off-shore units may or may not prove to be as good of value as our good used original FoMoCo reconditioned units. Notice they do not have the correct pigtails in place. To date, all we can find for these cars are foreign made units. Keep in mind our used units carry a one year warranty and these new motors have a 30 day warranty. Also know that the mounting plate is included...

Our heater cores are the finest available anywhere for any price. Constructed from corrosion resistant copper and brass. A great buy for anyone who is sick of smelling anti-freeze and needing to make repairs to this vital part.Replaces Ford Part #: D1ZZ-18476-B. Check out our video below on how to replace a heater core! We used a '69 Cougar with AC, but many of the same concepts apply to other years. ...

Reproduction heater resistor attaching pins correct for 1967-68 Mercury Cougar and Ford Mustang, but works fine with 1969-73 cars too. Sold in sets of 2 pins.

Metal fan wheel or squirrel cage for any 1967-73 Mercury Cougar or Ford Mustang with factory air conditioning only. Dimensions 5-3/4 inches in diameter and 4-1/8 inches tall. Shipped used as they come out of the cars, most will need cleaning and have light pitting. Some variations in the stampings, come 'as balanced' from the factory. Comes with allen set screw.

Used OEM Ford heater blower motor resistor that attaches to the heater blower fiberglass housing. We inspect these for damage or broken wires and we guarantee these will make your fan work. Not only was this heat resistor was factory installed on 1969-73 Cougars and Mustangs, but also on 1968 and newer Fairlanes, Torinos, Rancheros, Cyclones, and Montegos. Also installed on 1970 and newer Mavericks / Comets, plus 1971 and newer Lincolns.Ford part # C8OZ-18591-A.*Note - Excludes Heater with...

Heater cable for Cougars and Mustangs that are not equipped with factory air conditioning. Ford Part #: D1ZZ-18518-A

This used heater fan switch mounts to the rear of the heater control panel. It is a good working switch, wiring pigtail, and plug. Also, because it is original, it will fit right the first time. Save your knob, because this part does not come with one. If you don't have the knob, its OK, I know where you can get a mint set. KNOBS. Replaces part # D1ZZ-18578-A.

Complete used heater control assembly that includes a bezel / face plate, bracket control mounting plate, electrical switches, and vacuum switches. Functional, driver quality, heater control assembly. Knobs and light socket wiring harness not included. Replaces part # D1ZZ-18A651-A. *RESTORATION TIP* If you like to restore your own parts, you can purchase plastic polish for the lenses that will take out the haze with a bit of elbow grease. A silver paint pen (purchased from most artist...

Push on retainer for heating and air conditioning box levers or shafts. Fits 3/16 inch studs or rods. In most cases you will also want to get a washer to go against the pinched stops. Probably fits most Ford products, not just 1967-73 Cougar and Mustang.Replaces Ford part number 383358-S.

Washer or spacer for heating and air conditioning box levers or shafts. Fits 3/16 inch studs or rods. In most cases you will also want to get a push on retainer to keep secure.

Air inlet damper door for any 1969-73 Mercury Cougar or Ford Mustang with factory or integral air conditioning. The damper door allows re-circulating or fresh air to enter the fiber glass A/C box. Dimensionally the same as the 1967-68 door, but with two small notches, instead of one. Part cleaned for photograph, normally will ship 'as removed'. Inspected for excessive rust pitting or weakness of the metal, they all will have a slight amount of metal degradation from being assembled as bare...

Evaporator door for any 1967-73 Mercury Cougar or Ford Mustang with factory or integral air conditioning. The evaporator door allows air to pass over the evaporator in the A/C box. Part cleaned for photograph, normally will ship 'as removed'. Inspected for excessive rust pitting or weakness of the metal, they all will have a slight amount of metal degradation from being assembled as bare metal. Door only, shaft not included, but available. See related parts.Replaces Ford part number...

Used fresh air vent found in the driver side kick panel of all 1971-73 Mercury Cougar without air conditioning. Replaces Ford part number D1WY-6501935-A.

Used fresh air vent duct found behind the driver side dash panel of all 1971-73 Mercury Cougar without air conditioning. Restoration tip - Ford used a ring of foam as a seal between the duct and fresh air vent. Replaces Ford part number D1WY-6501878-A.

Used cable and knob assembly for opening the driver side fresh air vent on 1971-73 Mercury Cougar without air conditioning. Cable control mounts through the dash in a special dash bezel. About 13 inches in total length.Replaces Ford part number D1WY-6501891-A.*Note - Does not fit Mustang.

Chromed plastic driver side fresh air "Vent" bezel. Mounts with the cable through a hole in the dash panel, just to the right of the vent register. Most all of these used bezels have a defect in the chrome plating along the bottom, not visible when installed.Replaces Ford part D1WA-18A405 (casting in the part), or D1WY-10852-B.*Note - Does not fit Mustang

Used mounting and indexing bracket for the driver side fresh air vent cable on all 1971-73 Mercury Cougars without air conditioning. This bracket goes behind the dash panel and keeps the vent cable attached and indexed correctly. A 7/16-14  hex nut is also needed for mounting the cable. (Sold separately)Replaces Ford part number D1WY-6501822-A.

Used mounting nut for the driver side fresh air vent cable on all 1971-73 Mercury Cougars without air conditioning. This nut screws onto the cable.  7/16-14  hex nut with 11/16" hex. (Sold separately)*Hint this is an easy to find hardware store nut, nothing else special about it.Replaces Ford part number 34670-S.

Used mounting bracket for the driver side fresh air vent cable on all 1971-73 Mercury Cougars without air conditioning. This bracket mounts to a tab on the fresh air vent, and keeps the cable stationary.  Replaces Ford part # D1WY-18C587-A.

Used steel bracket for mounting the passenger side fresh air vent cable to the bottom of the dash below the glove box. 1971-73 Mercury Cougar only.Replaces Ford part # D1WA-6501861-AC.*NOTE* Does not fit Ford Mustang.

Lower dash bezel to the left of the steering column. This one is for those 1971-73 Mercury Cougars without factor air conditioning. Cars with only the heater option had dual fresh air vents. This bezel is for the driver side fresh air vent register and control cable, it has a molded hole for the vent cable.Replaces Ford part number D1WB-65044A13-AC (cast on the part) or D1WY-6504393-A.

New clear plastic lens or face plate for the heater control on all 1971-72, and early 1973 Mercury Cougar or Ford Mustang. These are constructed with the bend on the top to refract the light for illumination. About October 1972, Ford changed the word FLOOR, to HEAT. The lens plates will physically interchange, you can either one depending upon preference.*Tip for removal of your old lens. We have found it easiest to use a dremmel or other type of small cutoff wheel to carefully grind away the...

Clips that attach to the dash for mounting the defrost nozzles. Package of 3 clips and nuts. Good for cars with or without A/C. Typically found on 69-73 cars, but will also fit and work on 1967-68 as well.Replaces Ford part number 357849-S100.

D1ZA-18C433 lower heater duct to floor outlet for 1971-73 Mercury Cougar and Ford Mustang without air conditioning. Used grade "A" part and may have one very minor scuff. Ford number D1ZA-18C433-AD

Brand new athletic T-shirt from West Coast Classic Cougar! Features distressed university-style block letters and a walking cat logo in gold, on a comfy navy blue heather shirt. A great way to represent your favorite car, favorite coast, or favorite car parts business. Makes an excellent gift for the Cougar fan in your life.Shirt specs:6.0 oz., pre-shrunk 50/50 cotton/polyesterDouble-needle stitched neckline, bottom hem and sleevesQuarter-turnedTaped neck and shouldersSeamless seven-eighths...

Brand new ladies athletic T-shirt from West Coast Classic Cougar! Features distressed university-style block letters and a walking cat logo in gold, on a comfy navy blue heather shirt. A great way to represent your favorite car, favorite coast, or favorite car parts business. Makes an excellent gift for the Cougar fan in your life. Shirt specs: 6.0 oz., pre-shrunk 50/50 cotton/polyesterDouble-needle stitched neckline, bottom hem and sleevesQuarter-turnedTapered neck and shouldersSeamless...

Non-original style replacement clip for mounting the quarter window regulator arm to the window channel bracket on all 1969-70 Cougar and Mustang coupe and convertibles. This clip will work with either the 1969-early 1970 bracket and the late 1970 bracket. The late 1970 brackets used a unique spring steel clip that seldom is reusable. Sold individually, one each per window.

Reproduction roofrail weatherstrip seal clip and quarter window guide clip for the 1971

Used passenger side quarter window regulator for all 1971-73 Mercury Cougar and Ford Mustang with manual crank rear windows. Ford part number D1ZZ-6530306-A.

1971 - 1973 Mercury Cougar and Ford Mustang coupe clear glass for the passenger side rear seating area

1971 - 1973 Mercury Cougar and Ford Mustang coupe clear glass for the driver side rear seating area

1971 - 1973 Mercury Cougar and Ford Mustang convertible clear glass for the driver side rear seating area

1971 - 1973 Mercury Cougar and Ford Mustang convertible Grade B clear glass for the passenger side rear seating area, it will not have the faint green tint like the SUN-X factory tinted glass. Good used rear quarter glass with minor vertical scratches due to hardened belt line rubber seal and debris caught within the belt line seal. Vertical chrome trim not include. Ford part # D1ZZ-7629710-A. *NOTE* Air conditioning cars were supposed to have SUN-X tinted glass. Look for the SUN-X logo in the...

1971 - 1973 Mercury Cougar and Ford Mustang convertible Grade B clear glass for the driver side rear seating area, it will not have the faint green tint like the SUN-X factory tinted glass. Good used rear quarter glass with minor vertical scratches due to hardened belt line rubber seal and debris caught within the belt line seal. Vertical chrome trim not include. Ford part number D1ZZ-7629711-A. *NOTE* Air conditioning cars were supposed to have SUN-X tinted glass. Look for the SUN-X logo in...

1971 - 1973 Mercury Cougar and Ford Mustang coupe Grade B clear glass for the passenger side rear seating area, it will not have the faint green tint like the SUN-X factory tinted glass. Good used rear quarter glass with minor vertical scratches due to hardened belt line rubber seal and debris caught within the belt line seal. Vertical chrome trim not include. Ford part number D1ZZ-6529710-A. *NOTE* Air conditioned cars were supposed to have SUN-X tinted glass. Look for the SUN-X logo in the...

1971 - 1973 Mercury Cougar and Ford Mustang coupe Grade B clear glass for the driver side rear seating area, it will not have the faint green tint like the SUN-X factory tinted glass. Good used rear quarter glass with minor vertical scratches due to hardened belt line rubber seal and debris caught within the belt line seal. Vertical chrome trim not included. Ford part number D1ZZ-6529711-A. *NOTE* - Air conditioning cars were supposed to have SUN-X tinted glass. Look for the SUN-X logo in the...

Good reproduction made in Taiwan. Much higher quality than the Chinese version of this regulator. Replaces Ford part # D1ZZ-6523206-A. Do you have questions about Glue-In vs Bolt-In glass? How about how to properly install Glue-In glass in your 1969 Cougar or Mustang? Check out our video below for some great glassy information! 1969 Glue-In Glass: The Comprehensive Repair Guide Video

Good reproduction made in Taiwan. Much higher quality than the Chinese version of this regulator. Replaces Ford Part #: D1ZZ-6523207-A Do you have questions about Glue-In vs Bolt-In glass? How about how to properly install Glue-In glass in your 1969 Cougar or Mustang? Check out our video below for some great glassy information! 1969 Glue-In Glass: The Comprehensive Repair Guide Video

1971 - 1973 Mercury Cougar and Ford Mustang coupe factory tinted glass for the passenger side rear seating area, it will have the faint green tint and be marked SUN-X. Very good used door glass with no deep scratches (multiple faint scratches and water spots often will be present). Not perfect but the best you could expect to find from a 50 year old plus parts car and will of course be a better fit than repro. Glass does not ship with chrome seal divider. Ford part number D1ZZ-6529710-B....

1971 - 1973 Mercury Cougar and Ford Mustang coupe factory tinted glass for the driver side rear seating area

1971 - 1973 Mercury Cougar and Ford Mustang convertible factory tinted glass for the passenger side rear seating area, it will have the faint green tint and be marked SUN-X. Very good used door glass with no deep scratches (multiple faint scratches and water spots often will be present). Not perfect but the best you could expect to find from a 50 year old plus parts car and will of course be a better fit than repro. Glass does not ship with chrome seal divider. Ford part number D1ZZ-7629710-B....

1971 - 1973 Mercury Cougar and Ford Mustang convertible factory tinted glass for the driver side rear seating area

1971 - 1973 Mercury Cougar and Ford Mustang convertible Grade B factory tinted glass for the passenger side rear seating area, it will have the faint green tint and be marked SUN-X. Good used rear quarter glass with minor vertical scratches due to hardened belt line rubber seal and debris caught within the belt line seal. Vertical chrome trim not include. Ford part number D1ZZ-7629710-B. *NOTE* Air conditioning cars were supposed to have SUN-X tinted glass. Look for the SUN-X logo in the...

1971 - 1973 Mercury Cougar and Ford Mustang convertible Grade B factory tinted glass for the driver side rear seating area, it will have the faint green tint and be marked SUN-X. Good used rear quarter glass with minor vertical scratches due to hardened belt line rubber seal and debris caught within the belt line seal. Vertical chrome trim not include. Ford part number D1ZZ-7629711-B. *NOTE* Air conditioning cars were supposed to have SUN-X tinted glass. Look for the SUN-X logo in the bottom...

1971 - 1973 Mercury Cougar and Ford Mustang coupe Grade B factory tinted glass for the passenger side rear seating area, it will have the faint green tint and be marked SUN-X. Good used rear quarter glass with minor vertical scratches due to hardened belt line rubber seal and debris caught within the belt line seal. Vertical chrome trim not include. Ford part number D1ZZ-6529710-B. *NOTE* Air conditioning cars were supposed to have SUN-X tinted glass. Look for the SUN-X logo in the bottom rear...

1971 - 1973 Mercury Cougar and Ford Mustang coupe Grade B factory tinted glass for the driver side rear seating area, it will have the faint green tint and be marked SUN-X. Good used rear quarter glass with minor vertical scratches due to hardened belt line rubber seal and debris caught within the belt line seal. Vertical chrome trim not included. Ford part # D1ZZ-6529711-B. *NOTE* Air conditioning cars were supposed to have SUN-X tinted glass. Look for the SUN-X logo in the bottom rear...

Brand new TINTED Tempered glass with no scratches or excuses. We guarantee this to be a perfect fit. This glass does not have the faint Car-Lite markings in the corner but rather very bold

Excellent upgrade for your Cougar or Mustang

Brand new CLEAR Tempered glass with no scratches or excuses. We guarantee this to be a perfect fit. This glass does not have the faint Car-Lite markings in the corner but rather very bold

New green tinted driver side glass for any 1971-73 Mercury Cougar or Ford Mustang Convertible. Replaces SUN-X tinted glass. This glass does not have the faint Car-Lite markings in the corner but rather very bold

Used driver side (left hand) quarter window regulator for the Mercury Cougar or Ford Mustang. Manual crank windows only, power window regulators are different. Nothing beats or fits like FoMoCo!Ford part number D1ZZ-6530307-A

Used bracket for mounting the bottom of the quarter window guide to the car body. Fits all 1971-73 Mercury Cougar and Ford Mustang coupe and convertible (non fastback). "L" shaped bracket that designed for mounting and adjusting the rear quarter window.Replaces Ford part number D1ZZ-65298A56.

New green tinted passenger side glass for any 1971-73 Mercury Cougar or Ford Mustang Convertible. Replaces SUN-X tinted glass. This glass does not have the faint Car-Lite markings in the corner but rather very bold

Good used driver side (left hand) quarter window guide for the 1971-73 Mercury Cougar or Ford Mustang. This unit will ship as shown. All brackets come with rubber bumpers installed. We may substitute a new bumper for a missing bumper. We recommend a thorough cleaning and a liberal amount of Sil-Glyde grease or equivalent during re-assembly. Ford part # D1ZZ-6529753-A.

Good used passenger side (right hand) quarter window guide for the 1971-73 Mercury Cougar or Ford Mustang. Ford part # D1ZZ-6529752-A.

This support bracket mounts to the lowest portion of the quarter window cavity. This bracket is installed before the lower guide bracket. Fits all 1971-73 Mercury Cougar models and 1971-73 Ford Mustang models including fastback or sport roof models. The exploded view of the quarter window parts can be found in the Osborn Body Assembly Manual for 1971-72. One for each quarter window

Quarter window upper stop bracket

Quarter window lower stop bracket

Quarter window guide roller with swivel head for all 1971-73 Mercury Cougar or Ford Mustang Coupe or Convertible. Three of these rollers per side

Cupped metal washer with center hole with flat sides for installing the two upper swivel rollers on the rear quarter windows. 2 per side 4 total per car. Fits 1971-73 Mercury Cougar and Ford Mustang Coupe and Convertible.Ford part number D1OZ-57263A86-A.

Used quarter window shoulder screw and nut for the 71 - 73 Cougar and Mustang.

New clear passenger side glass for any 1971-73 Mercury Cougar or Ford Mustang Convertible. Replaces Tempered clear glass. This glass does not have the faint Car-Lite markings in the corner but rather very bold

New clear driver side glass for any 1971-73 Mercury Cougar or Ford Mustang Convertible. Replaces Tempered clear glass. This glass does not have the faint Car-Lite markings in the corner but rather very bold

Used passenger side bracket for mounting the quarter window glass. Fits all 1971-73 Mercury Cougar and Ford Mustang coupe and convertible (non fastback). Bracket ships as shown

Used driver side bracket for mounting the quarter window glass. Fits all 1971-73 Mercury Cougar and Ford Mustang coupe and convertible (non fastback). Bracket ships as shown

New slotted pan head screw for mounting distributor points or condensers. Three total, per single advance Ford distributors. We know that these fit FoMoCo, Autolite and Motorcraft marked distributors 1967-73. These are AMK screws 8-32x9/32". Sold individually, but you likely need 3. 

New phosphate dipped slotted pan head screw for mounting distributor vacuum advances. Two total, per Ford distributor. We know that these fit FoMoCo, Autolite and Motorcraft marked distributors 1967-73. These are AMK screws 8-32x1". Sold individually, you will need 2.