All Available Parts - 1971 Mercury Cougar

This direct replacement is the 2-1/4 inch H pipe only and is for any 1971-73 Mercury Cougar or Ford Mustang with stock cast iron exhaust manifolds. These units are manufactured right here in the good old USA from 2-1/4 inch aluminized pipes and made from an original 1971 Cougar and Mustang with either the H, M, or Q code 351C engine. We also sell OEM style dual exhaust systems that include the H pipe, mufflers, and tail pipes.*NOTE* Will not fit 351 Windsor, 1970 351 Cleveland engines. Please...

This direct replacement is the 2-1/4 inch H pipe only and is for any 1971 Mercury Cougar or Ford Mustang with stock cast iron exhaust manifolds. These units are manufactured right here in the good old USA from 2-1/4 inch aluminized pipes and made from an original 1971 Cougar and Mustang with the 429CJ engine. We also sell OEM style dual exhaust systems that include the H pipe, mufflers, and tail pipes.*NOTE* Please allow 2 - 3 weeks for delivery.

This direct replacement is the 2 inch Y pipe only with 2-1/4 intermediate pipe outlets and is for any 1971-73 Mercury Cougar or Ford Mustang with stock cast iron exhaust manifolds. These units are manufactured right here in the good old USA from 2 inch aluminized pipes and made from an original 1971 Cougar and Mustang with the 351C 2V engine. We also sell OEM style dual exhaust systems that include the H pipe, mufflers, and tail pipes.*NOTE* Will not fit 1970 351 Cleveland engines. Please...

This 2-1/4 inch dual exhaust system is manufactured right here in the good old USA from an original 1971 429CJ Cougar. This direct replacement system includes: 1 H pipe, 2 intermediate pipes, 2 mufflers, and a right and left tail pipe. The system is constructed from 2-1/4 inch aluminized piping and features blue printed bends with everything being replicated as close as possible to the original. The mufflers in the system have the hanging tabs attached so that they will accept original...

This 2-1/4 inch dual exhaust system is manufactured right here in the good old USA from original 1971 M code and 1972-73 Q code Cougars equipped with the 351C engine. This direct replacement system includes: 1 H pipe, 2 intermediate pipes, 2 mufflers, and a right and left tail pipe. The system is constructed from 2-1/4 inch aluminized piping and features blue printed bends with everything being replicated as close as possible to the original. The mufflers in the system have the hanging...

Now in grey with no zipper, our comfy WCCC hoodie features bold new walking cat graphics on front and back. Perfect for staying warm in the garage, or out and about with your Cougar! This sweatshirt is made with soft, mid weight fleece and generous fit for comfort. Features a jersey lined hood, heavy gauge drawcord with metal eyelets and 1x1 ribbing at cuffs and waistband. 8.5 oz fleece80% cotton 20% polyester blend100% cotton 20 singles face yarnSplit stitch double needle sewing on all...

Now in black with no zipper, our comfy WCCC hoodie features bold new walking cat graphics on front and back. Perfect for staying warm in the garage, or out and about with your Cougar! This sweatshirt is made with soft, mid weight fleece and generous fit for comfort. Features a jersey lined hood, heavy gauge drawcord with metal eyelets and 1x1 ribbing at cuffs and waistband. 8.5 oz fleece80% cotton 20% polyester blend100% cotton 20 singles face yarnSplit stitch double needle sewing on all...

Housing overall width - 55-3/4 inches flange to flange. Spring perches are 43 inches apart on center. Bare housing with proper axle pad spacing for all 1971-1973 Cougars. Over-sized shipping length.Axles needed: Passenger side - 32 inches long, Driver side 28 inches long.

Right side axle, 28 spline 31-7/8 inch length. Ships with used bearing, bearing retainer plate, and 5 pressed in wheel studs. *Note 429 CJ equipped Cougars came with heavy duty 31 splined axles.

Left side axle, 28 spline 27-13/16 inch length. Ships with used bearing, bearing retainer plate, and 5 pressed in wheel studs. *Note 429 CJ equipped Cougars came with heavy duty 31 splined axles.

Since we always claim to have parts nobody else does... This welds to the bottom side of the car just above the differential. When the rear suspension bottoms out, this is the plate the rubber snubber / bumper (mounted on the front on top of the dif.) makes contact with.

Also called a pumpkin, 2.75:1 open ratio. Check your door tag under "Axle". 1968 code 1 1969-73 code 2

Mounts over rear axle ends into the body/frame, two required per car, this is the more pointed Christmas tree shaped version.Ford part # C6AZ-4730

D0OZ-4204-9A300 1968-1973 9 Inch Third Member - Used Also called a pumpkin, 3.00:1 open ratio. These 3rd members will have the fill plug. Check your door tag under "Axle".

NOTE! When we ship a rear end, we will remove the third member and ship it in a separate box. Some assembly will be required. Housing overall width - 55-3/4 inches flange to flange. Spring perches are 43 inches apart on center. Overall width measured from faces of axles, not the tips. All 1971-73 have the same overall width of 61 inches.   Rear axle assembly - Housing, Axles, brake backing plates, and third member. As removed from a 1971-73 West Coast Cougar organ donor car. We...

#373820-S Copper washer for attaching the 8 inch or 9 inch third members to the axle housings. Steel washers will leak, made from copper which is a soft metal and seals under the attaching nuts. Copper washers like the OEM Ford installed washers. Takes 10 washers total for both 8 and 9 inch rear ends. *Tip - It is a good idea to inspect or replace your old washers, many times they have tool marks from the housing or nuts that cause small troublesome leaks.

This gas Shock Absorber improves handling without sacrificing ride comfort. A very good choice for the daily driver wanting a smooth ride with the response of a gas shock.  These shocks are sold individually and are designed more specifically to work with Cougars as opposed to Mustang. Manufacturer Specs: ExtendedCompressedStrokeCoverInternal StopExternal Stop19.3711.308.07X-- ...

These shocks are the as close to original specs as possible for the Mercury Cougar. This is the performance shock for those looking for firmer ride. The KYB Gas-a-Just shocks use higher gas pressure to keep your tires glued to the road. The KYB Gas-a-Just shocks' velocity-sensitive valving system adjusts quickly to changing road conditions for maximum comfort in any situation. Their mono tube configuration eliminates aeration and foaming, their micro-smooth, hard-chromed pistons extend their...

Used half vinyl top roof trim from a 1971-73 Mercury Cougar for the driver side. Half vinyl top option was a partial covered vinyl roof starting at the windshield and extending rearwards past mid-way on the roof. Not to be confused with the complete vinyl roof covering trim. These have been restored with the correct bright dipped, anodize finish. This is a trim restoration service, if you do not have an acceptable core trim piece, please purchase a core driver vinyl half roof trim. Call...

Used half vinyl top roof trim from a 1971-73 Mercury Cougar for the passenger side. Half vinyl top option was a partial covered vinyl roof starting at the windshield and extending rearwards past mid-way on the roof. Not to be confused with the complete vinyl roof covering trim. These have been restored with the correct bright dipped, anodize finish. This is a trim restoration service, if you do not have an acceptable core trim piece, please purchase a core passenger vinyl half roof trim. Call...

Front driver side wheel lip moulding. Fits all 1971-73 Mercury Cougars.Replaces Ford part number D1WY-16039-A.

Rear passenger side wheel lip moulding. Keep in mind we will take a restorable core moulding in partial trade on this very hard to find part.Replaces Ford part number D1WY-6529164-A.

Used seat belt warning light relay for most Ford Lincoln and Mercury cars starting in 1967 until sometime in 1972 when a Motorcraft version of this exact relay was produced. This is a timed relay that allows several seconds of illumination to your seat belt warning light. Ford Part number C7AB-10B924-B1 or Ford Service part number D1AZ-10B924-A

Low fuel relay for all 1971-73 Mercury Cougar XR7 models, body code 65F and 76F only. Stamped D1WF-10A968-AA. These are tested and working relays.Fits 1971 Cougar XR7 Fits 1972 Cougar XR7Fits 1973 Cougar XR7

Used in 1971-73 Mercury Cougars and Ford Mustang for the stop lamps, located under the dash on a panel next to the fuse block.15amp circuit breaker. It is 1.25" x 13/16" and has a single green dot. Box is marked FASCO, 15AMP 12V, and made in the U.S.A. Integrated mounting tab for this application. Ford part number D1MY-14526-A. *NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the...

Tested and working relay for the 'headlights - on' reminder. Relay with mounting tab for 1971-73 Mercury Cougar and Ford Mustang. This relay controls a buzzer as a reminder to turn off the headlights or remove the key, when the door is opened.Replaces Ford part number D1AB-10C838-A or D1AZ-10C838-A.

For any 1971, 1972, 1973 Mercury Cougar. The 1/2" sway bar for Competition Handling was optional on any 1971-73 Cougar, but it was included automatically on all 1971 GT's, 429 Cobra Jets, and with the 1972 & 1973 Q code engine option (351CJ). Concours restorers, should be painted all chassis black with 1 White stripe. This factory used 1/2" rear sway bar, does not include any mounting brackets or end link kits. Replaces Ford part number D1WY-5A772-A.Here's our little film to help you...

Passenger side shock mounting plate for any 1967-73 Mercury Cougar with any V-8 engines. A passenger side and **driver side bracket are needed for most applications.  **Excludes 1969 - 1970 Boss 302 & 428 Cobra Jet 4 speed Cougars. Additionally 1972 - 1973 351CJ (Q code engines - all transmissions) which all came with staggered rear shocks, which was part of those years Competition Handling Package. These applications had staggered rear shock plates. Order two C9OZ-5796-C right...

This 2 degree wedge properly sets the pinion angle for the drive shaft.The Mercury Parts Catalog states that this part is installed "As Required".Orientation: Narrow end towards the front of the car.

This 1.5 degree wedge properly sets the pinion angle for the drive shaft.The Mercury Parts Catalog states that this part is installed "As Required".Sold individually, two required per vehicle.Orientation: Narrow end towards the front of the car.

This 1 degree wedge properly sets the pinion angle for the drive shaft.The Mercury Parts Catalog states that this part is installed "As Required".Orientation: Narrow end towards the front of the car.

Limited slip 8 inch Ford third member rebuilt with all new parts. Factory new 4 pinion Trac-Loc unit, new Motive ring and pinion gears, new Timkin bearings, new crush sleeve, new bolts, and new seal. Rebuilt using 1967 and newer two rib style case, with oil fill plug, and standard 1310 yoke. There are various ring and pinion (gear) ratios and axle splines available, if you are unsure of what you need it is best to call (503) 463-1130 for your order. This is a drop ship item. *Note - New...

Limited slip 8 inch Ford third member rebuilt with all new parts. Factory new Eaton True-Trac 8 pinion clutchless traction locking unit, Richmond ring and pinion gear, Timkin bearings, crush sleeve, bolts, and seal. Rebuilt using 1967 and newer two rib style case, with oil fill plug, and standard 1310 yoke. Ships with direction sheet and bottle of Ford Motorcraft friction modifier additive for the rear end gear oil. For use with 28 splined axles, but can be custom...

Limited slip 9 inch Ford third member rebuilt with all new or reconditioned parts. Rebuilt 4 pinion Trac-Loc unit, with new clutches, steels, Richmond ring and pinion gears, Timkin bearings, crush sleeve, bolts, and seal. Rebuilt using standard 9 inch cases with oil fill plug. Ships with direction sheet and bottle of Ford Motorcraft friction modifier additive for the rear end gear oil. For 28 or 31 splined axles. This unit was used in Cougars and Mustangs, but also any other Fords...

Limited slip 9 inch Ford third member rebuilt with all new parts. New 4 pinion Trac-Loc unit, Richmond ring and pinion gears, Timkin bearings, crush sleeve, bolts, and new a seal. Rebuilt using the standard 9 inch case, with oil fill plug. Ships with direction sheet and bottle of Ford Motorcraft friction modifier additive for the rear end gear oil. For 28 or 31 splined axles. This unit is for 1967-73 Cougars and Mustangs, but it works for any other Mercurys or Fords with a 9 inch...

Limited slip 9 inch Ford third member rebuilt with all new parts. New Eaton True-Trac 8 pinion clutchless traction locking unit, Richmond ring and pinion gear, Timkin bearings, crush sleeve, bolts, and seal. Rebuilt using 1967-1973 standard 9 inch case with oil fill plug. For 28 or 31 splined axles. This unit is for 1967-73 Cougars and Mustangs, but can be used on any other Ford or Mercury with a 9 inch drop out center section. Because of all the various ring and pinion...

Limited slip nodular 9 inch Ford third member rebuilt with all new parts. New 4 pinion Trac-Loc unit, Richmond ring and pinion gears, Timkin bearings, selective size sleeve, bolts, and seal. Rebuilt using a nodular 9 inch case with oil fill plug. Ships with direction sheet and bottle of Ford Motorcraft friction modifier additive for the rear end gear oil. For 28 or 31 splined axles. This unit is for 1967-73 Cougars and Mustangs, but it can also be used for any other Ford or...

Limited slip nodular 9 inch Ford third member rebuilt with all new parts. New Eaton True-Trac 8 pinion clutchless traction locking unit, Richmond ring and pinion gear, Timkin bearings, selective size sleeve, bolts, and seal. Rebuilt using a 1967-1973 nodular 9 inch case with oil fill plug. For 28 or 31 splined axles. This unit is for 1967-73 Cougars and Mustangs, but can be used in any other Ford or Mercury with a 9 inch drop out center section. Because of all the...

Limited slip, nodular 9 inch Ford third member rebuilt with all new or reconditioned parts. Used modern design Detroit Locker unit, new Richmond ring and pinion gear, new Timkin bearings, new selective size sleeve, new bolts, and new seal. Rebuilt using 1967-1973 nodular 9 inch cases with oil fill plug, for 28 or 31 splined axles. This unit was used in 1967-73 Cougars and Mustangs, but it also came in any other Fords or Mercurys with a 9 inch drop out center section....

Used 20 amp circuit breaker for either 69 - 70 or 71-73 Cougars.Mounted on the Starter solenoid in 69-70 cougars for convertible tops or power windows, and also on 71-73 Standard Cougars for convertible tops, power windows, heated back light, power seats or seat back release.On the 71-73 XR7 the circuit breaker was mounted next to the starter solenoid on a junction block. Different wire diagrams, owner / shop manuals list this circuit breaker in both locations, possibly due to multiple...

Bracket mounts to top of stock cast iron Cleveland intake manifold, holding the throttle cable. Used on both the 351-2V and 351-4V engines with original Ford cast iron intake manifolds. There are two versions of this bracket per the MPC, it is such a minute detail, it is hardly worth listing separately.Replaces Ford part number D1ZZ-9728-E and D1AZ-9728-H.

Shaft diameter 3 inches, length 53-13/16 inches measured on U-joint centers. Used and 'as balanced' from the factory. Ask about slip yokes. Shipping is oversized due to length. *TRIVIA* All 71-73 stick shift 351C-4V powered Cougars were equipped with the top loader 4 speed transmission.

Shaft diameter 3 inches, length 53-15/16 inches measured on U-joint centers. Used and 'as balanced' from the factory. Ask about slip yokes. Shipping is oversized due to length. *TRIVIA* All manually shifted H-code 351-2V engines were 3 speeds, you could not get the 4 speed with that combo. Read about it in Cougars by the Numbers book.

Check your door data plate for code X in the transmission box. Shaft diameter 3 inches. Length 54-1/4 inches, measured on U-joint centers. Used and 'as balanced' from the factory. Ask about slip yokes. Shipping is oversized due to length.

Check your door data plate for code U in the transmission box. Shaft diameter 3 inches. Length 50-13/32 inches, measured on U-joint centers. Used and 'as balanced' from the factory. Ask about slip yokes. Shipping is oversized due to length. Ford part # D1WY-4602-C.*NOTE* Excludes Q code 351CJ engines.

31 Spline transmission slip yoke for all 1969 351-2v/4v and 1970-1973 351-2v FMX  cars.  *Excludes 351C-4v and 351CJ engines.

Sold individually, but two are required for the rear suspension. Replaces Ford 5630 shackle kits that include bushings C6DZ-5781-A.

Correct length and construction shackle for all 1971 through 1972 Cougars manufactured between 10/70 and 9/71. Ships complete - 2 piece shackle with original nuts. New bushings not included, but recommended. Sold individually, but two are required for the rear suspension. These also fit 1970 - 1972 Ford Mustangs. Replaces Ford 5630 shackle kits that include bushings C6DZ-5781-A.

Set of 1-1/4" leaf spring rubber bushings for the rear eye of the spring. Sold in packages of 8, 4 per side. Correct shackle bushings for all 1971 through 1972 Cougars manufactured between 10/70 and 9/71. Replaces Ford Part #: C6ZZ-5781-B & C6DZ-5781-A.

Set of 1" leaf spring poly bushings for the rear eye of the spring. Sold in packages of 8, 4 per side. Correct shackle bushings for all 1971 through 1972 Cougars manufactured between 10/70 and 9/71. 1 5/16" OD.5" ID1.25" insert depth. .25" lip Replaces Ford Part #: C6ZZ-5781-B & C6DZ-5781-A. May be Dropshipped

Keep in mind these will work on the Cougar but are designed for the Mustang which has a lower maximum spring travel. If your Cougar is lowered in the rear by an inch or more these will be spot on.Sold individually

[No Description Provided]

These shocks are the as close to original specs as possible for the Mercury Cougar. This is the comfort shock for those looking for a softer ride. The KYB Gas-a-Just shocks use higher gas pressure to keep your tires glued to the road. The KYB Gas-a-Just shocks' velocity-sensitive valving system adjusts quickly to changing road conditions for maximum comfort in any situation. Their mono tube configuration eliminates aeration and foaming, their micro-smooth, hard-chromed pistons extend their...

New axle bearing for any 8 or 9 inch Ford rear end with 28 splined axles. Common on all Mercury Cougar and Ford Mustang with V-8 engines. Excludes 31 splined axles as found on Boss and Cobra Jet cars.These should be professionally installed with a bearing press.

New outer axle gasket for any 8 or 9 inch Ford rear end with 28 splined axles. Common on all Mercury Cougar and Ford Mustang with V-8 engines. Excludes 31 splined axles as found on Boss and Cobra Jet cars. One required per side, two per car.

Rear axle vent bolt for the 67 - 73 Cougar or Mustang. This bolt serves a dual purpose, as it also holds the brake line bracket in place on the axle tube.

NOTE: Some modification required to fit Cougars! These are actually 69-70 Mustang wheel lip mouldings, which have a different shape / contour. However, with a bit of massaging they can be made to fit the 71 - 73 Cougar. They are the closest alternative we have found that fits and looks reasonably good for much less than restored originals. Check out our video below, showing how easy it is to install these mouldings on a Cougar ...

Concours rear axle vent hose for any 1967-73 Mercury Cougar or 1965-73 Ford Mustang. Rubber hose that attaches to the metal nipple on the top of your rear axle housing. Fits 8 and 9 inch rear ends. Includes hardware as shown. Crimp clamp, screw clamp and bolt. Ribbed hose like original, and has yellow paint mark like from the factory. About 20 inches of hose is included, a little more than what was from the factory. Part number 4A001 in the chassis assembly manual.

Reproduction leaf spring center bolt for your 67 - 73 Mercury Cougar.

Used passenger side leaf spring, front mounting bracket. All the same 1968-73 on Mercury Cougar. 1967 Mercury Cougar available, but slightly different in construction. You will receive the bracket attached to the unibody cut similarly to what is shown in the photo. 

Used driver side leaf spring, front mounting bracket. All the same 1968-73 on Mercury Cougar. 1967 Mercury Cougar available, but slightly different in construction. You will receive the bracket attached to the unibody cut similarly to what is shown in the photo. 

Used passenger side leaf spring, front mounting bracket. 1967 Mercury Cougar. 1968-73 Mercury Cougar available, but slightly different in construction. You will receive the bracket attached to the unibody cut similarly to what is shown in the photo. 

Used driver side leaf spring, front mounting bracket. 1967 Mercury Cougar. 1968-73 Mercury Cougar available, but slightly different in construction. You will receive the bracket attached to the unibody cut similarly to what is shown in the photo. 

Application all 1967-1968 289/302 engines with C4. 1967-1973 small block V-8 with 3 or 4 speed manual transmissions. Features 28 splines. Some have a casting number of C5AW-4888-A.Excludes Hi-performance V-8's such as Boss 302, 390, 428CJ, and C-6 / FMX transmissions.

Replaces Ford Part # C1AZ-4529-A Sold individually. All applications, attaches the drive shaft U-Joint to rear end pinion yoke. 5/16 Inch Diameter #24 thread for 1 1/8 inch Bearing Caps.

One size fits all universal joint u-bolt kit. Complete kit required to attach universal joint to rear differential. This kit only works with the 1-7/8 inch U-joint caps. Many of the higher performance engines used 2 inch caps and the larger yokes.  Replaces Ford Part #: C1AZ-4529-A or D3AZ-4529-A.

Reproduction universal joint that fits the transmission end of the drive axle on the Mercury Cougars and Ford Mustangs equipped with the 289, 302, 351 Windsor and most 351 Clevelands (see chart). this unit includes a grease fitting for an extended life. Replaces Ford part # C3AZ-4635-C or C3AZ-4635-E. *NOTE* Part number C3AZ-4635-C was discontinued in 1968 and was replaced by C3AZ-4635-E.

This reproduction universal joint is forged from high strength alloy steel that is crossed w/ an anti-corrosion coating. This unit also features a grease fitting for an extended life, and fits Mercury Cougars and Ford Mustangs equipped with the 289, 302, 351 Windsor and most 351 Clevelands (see chart). Part number C3AZ-4635-C was discontinued in 1968 and was replaced by C3AZ-4635-E. Span 3.30" cups 1.00" and 1.00"  Replaces Ford part # C3AZ-4635-C or C3AZ-4635-E. *NOTE* Part number...

Leaf Springs shipping time is 12 weeks. All of our springs are intended to return the car to factory height. Because of that, installing new springs will almost always increase the height of the rear of the car, as the factory leafs sag over the years. The competition springs will sit slightly lower than standard springs, somewhere between 1/2" and 1" lower. The competition springs cause the car to have a slightly lower the center of gravity and the competition springs are a stiffer spring, so...

Leaf Springs shipping time is 12 weeks. All of our springs are intended to return the car to factory height. Because of that, installing new springs will almost always increase the height of the rear of the car, as the factory leafs sag over the years. The competition springs will sit slightly lower than standard springs, somewhere between 1/2" and 1" lower. The competition springs cause the car to have a slightly lower the center of gravity and the competition springs are a stiffer spring, so...

Leaf Springs shipping time is 12 weeks. All of our springs are intended to return the car to factory height. Because of that, installing new springs will almost always increase the height of the rear of the car, as the factory leafs sag over the years. The competition springs will sit slightly lower than standard springs, somewhere between 1/2" and 1" lower. The competition springs cause the car to have a slightly lower the center of gravity and the competition springs are a stiffer spring, so...

Leaf Springs shipping time is 12 weeks. All of our springs are intended to return the car to factory height. Because of that, installing new springs will almost always increase the height of the rear of the car, as the factory leafs sag over the years. The competition springs will sit slightly lower than standard springs, somewhere between 1/2" and 1" lower. The competition springs cause the car to have a slightly lower the center of gravity and the competition springs are a stiffer spring, so...

Leaf Springs shipping time is 12 weeks. All of our springs are intended to return the car to factory height. Because of that, installing new springs will almost always increase the height of the rear of the car, as the factory leafs sag over the years. The competition springs will sit slightly lower than standard springs, somewhere between 1/2" and 1" lower. The competition springs cause the car to have a slightly lower the center of gravity and the competition springs are a stiffer spring, so...

Leaf Springs shipping time is 12 weeks. All of our springs are intended to return the car to factory height. Because of that, installing new springs will almost always increase the height of the rear of the car, as the factory leafs sag over the years. The competition springs will sit slightly lower than standard springs, somewhere between 1/2" and 1" lower. The competition springs cause the car to have a slightly lower the center of gravity and the competition springs are a stiffer spring, so...

Leaf Springs shipping time is 12 weeks. All of our springs are intended to return the car to factory height. Because of that, installing new springs will almost always increase the height of the rear of the car, as the factory leafs sag over the years. The competition springs will sit slightly lower than standard springs, somewhere between 1/2" and 1" lower. The competition springs cause the car to have a slightly lower the center of gravity and the competition springs are a stiffer spring, so...

Leaf Springs shipping time is 12 weeks. All of our springs are intended to return the car to factory height. Because of that, installing new springs will almost always increase the height of the rear of the car, as the factory leafs sag over the years. The competition springs will sit slightly lower than standard springs, somewhere between 1/2" and 1" lower. The competition springs cause the car to have a slightly lower the center of gravity and the competition springs are a stiffer spring, so...

Leaf Springs shipping time is 12 weeks. All of our springs are intended to return the car to factory height. Because of that, installing new springs will almost always increase the height of the rear of the car, as the factory leafs sag over the years. The competition springs will sit slightly lower than standard springs, somewhere between 1/2" and 1" lower. The competition springs cause the car to have a slightly lower the center of gravity and the competition springs are a stiffer spring, so...

Leaf Springs shipping time is 12 weeks. All of our springs are intended to return the car to factory height. Because of that, installing new springs will almost always increase the height of the rear of the car, as the factory leafs sag over the years. The competition springs will sit slightly lower than standard springs, somewhere between 1/2" and 1" lower. The competition springs cause the car to have a slightly lower the center of gravity and the competition springs are a stiffer spring, so...

Leaf Springs shipping time is 12 weeks. All of our springs are intended to return the car to factory height. Because of that, installing new springs will almost always increase the height of the rear of the car, as the factory leafs sag over the years. The competition springs will sit slightly lower than standard springs, somewhere between 1/2" and 1" lower. The competition springs cause the car to have a slightly lower the center of gravity and the competition springs are a stiffer spring, so...

Leaf Springs shipping time is 12 weeks. All of our springs are intended to return the car to factory height. Because of that, installing new springs will almost always increase the height of the rear of the car, as the factory leafs sag over the years. The competition springs will sit slightly lower than standard springs, somewhere between 1/2" and 1" lower. The competition springs cause the car to have a slightly lower the center of gravity and the competition springs are a stiffer spring, so...

Leaf Springs shipping time is 12 weeks. All of our springs are intended to return the car to factory height. Because of that, installing new springs will almost always increase the height of the rear of the car, as the factory leafs sag over the years. The competition springs will sit slightly lower than standard springs, somewhere between 1/2" and 1" lower. The competition springs cause the car to have a slightly lower the center of gravity and the competition springs are a stiffer spring, so...

Leaf Springs shipping time is 12 weeks. All of our springs are intended to return the car to factory height. Because of that, installing new springs will almost always increase the height of the rear of the car, as the factory leafs sag over the years. The competition springs will sit slightly lower than standard springs, somewhere between 1/2" and 1" lower. The competition springs cause the car to have a slightly lower the center of gravity and the competition springs are a stiffer spring, so...

Leaf Springs shipping time is 12 weeks. All of our springs are intended to return the car to factory height. Because of that, installing new springs will almost always increase the height of the rear of the car, as the factory leafs sag over the years. The competition springs will sit slightly lower than standard springs, somewhere between 1/2" and 1" lower. The competition springs cause the car to have a slightly lower the center of gravity and the competition springs are a stiffer spring, so...

Leaf Springs shipping time is 12 weeks. All of our springs are intended to return the car to factory height. Because of that, installing new springs will almost always increase the height of the rear of the car, as the factory leafs sag over the years. The competition springs will sit slightly lower than standard springs, somewhere between 1/2" and 1" lower. The competition springs cause the car to have a slightly lower the center of gravity and the competition springs are a stiffer spring, so...

Leaf Springs shipping time is 12 weeks. All of our springs are intended to return the car to factory height. Because of that, installing new springs will almost always increase the height of the rear of the car, as the factory leafs sag over the years. The competition springs will sit slightly lower than standard springs, somewhere between 1/2" and 1" lower. The competition springs cause the car to have a slightly lower the center of gravity and the competition springs are a stiffer spring, so...

Leaf Springs shipping time is 12 weeks. All of our springs are intended to return the car to factory height. Because of that, installing new springs will almost always increase the height of the rear of the car, as the factory leafs sag over the years. The competition springs will sit slightly lower than standard springs, somewhere between 1/2" and 1" lower. The competition springs cause the car to have a slightly lower the center of gravity and the competition springs are a stiffer spring, so...

Leaf Springs shipping time is 12 weeks. All of our springs are intended to return the car to factory height. Because of that, installing new springs will almost always increase the height of the rear of the car, as the factory leafs sag over the years. The competition springs will sit slightly lower than standard springs, somewhere between 1/2" and 1" lower. The competition springs cause the car to have a slightly lower the center of gravity and the competition springs are a stiffer spring, so...

Leaf Springs shipping time is 12 weeks. All of our springs are intended to return the car to factory height. Because of that, installing new springs will almost always increase the height of the rear of the car, as the factory leafs sag over the years. The competition springs will sit slightly lower than standard springs, somewhere between 1/2" and 1" lower. The competition springs cause the car to have a slightly lower the center of gravity and the competition springs are a stiffer spring, so...

Leaf Springs shipping time is 12 weeks. All of our springs are intended to return the car to factory height. Because of that, installing new springs will almost always increase the height of the rear of the car, as the factory leafs sag over the years. The competition springs will sit slightly lower than standard springs, somewhere between 1/2" and 1" lower. The competition springs cause the car to have a slightly lower the center of gravity and the competition springs are a stiffer spring, so...

Leaf Springs shipping time is 12 weeks. All of our springs are intended to return the car to factory height. Because of that, installing new springs will almost always increase the height of the rear of the car, as the factory leafs sag over the years. The competition springs will sit slightly lower than standard springs, somewhere between 1/2" and 1" lower. The competition springs cause the car to have a slightly lower the center of gravity and the competition springs are a stiffer spring, so...

Leaf Springs shipping time is 12 weeks. All of our springs are intended to return the car to factory height. Because of that, installing new springs will almost always increase the height of the rear of the car, as the factory leafs sag over the years. The competition springs will sit slightly lower than standard springs, somewhere between 1/2" and 1" lower. The competition springs cause the car to have a slightly lower the center of gravity and the competition springs are a stiffer spring, so...

Leaf Springs shipping time is 12 weeks. All of our springs are intended to return the car to factory height. Because of that, installing new springs will almost always increase the height of the rear of the car, as the factory leafs sag over the years. The competition springs will sit slightly lower than standard springs, somewhere between 1/2" and 1" lower. The competition springs cause the car to have a slightly lower the center of gravity and the competition springs are a stiffer spring, so...

Leaf Springs shipping time is 12 weeks. All of our springs are intended to return the car to factory height. Because of that, installing new springs will almost always increase the height of the rear of the car, as the factory leafs sag over the years. The competition springs will sit slightly lower than standard springs, somewhere between 1/2" and 1" lower. The competition springs cause the car to have a slightly lower the center of gravity and the competition springs are a stiffer spring, so...

Leaf Springs shipping time is 12 weeks. All of our springs are intended to return the car to factory height. Because of that, installing new springs will almost always increase the height of the rear of the car, as the factory leafs sag over the years. The competition springs will sit slightly lower than standard springs, somewhere between 1/2" and 1" lower. The competition springs cause the car to have a slightly lower the center of gravity and the competition springs are a stiffer spring, so...

Leaf Springs shipping time is 12 weeks. All of our springs are intended to return the car to factory height. Because of that, installing new springs will almost always increase the height of the rear of the car, as the factory leafs sag over the years. The competition springs will sit slightly lower than standard springs, somewhere between 1/2" and 1" lower. The competition springs cause the car to have a slightly lower the center of gravity and the competition springs are a stiffer spring, so...

Leaf Springs shipping time is 12 weeks. All of our springs are intended to return the car to factory height. Because of that, installing new springs will almost always increase the height of the rear of the car, as the factory leafs sag over the years. The competition springs will sit slightly lower than standard springs, somewhere between 1/2" and 1" lower. The competition springs cause the car to have a slightly lower the center of gravity and the competition springs are a stiffer spring, so...

Leaf Springs shipping time is 12 weeks. All of our springs are intended to return the car to factory height. Because of that, installing new springs will almost always increase the height of the rear of the car, as the factory leafs sag over the years. The competition springs will sit slightly lower than standard springs, somewhere between 1/2" and 1" lower. The competition springs cause the car to have a slightly lower the center of gravity and the competition springs are a stiffer spring, so...

Leaf Springs shipping time is 12 weeks. All of our springs are intended to return the car to factory height. Because of that, installing new springs will almost always increase the height of the rear of the car, as the factory leafs sag over the years. The competition springs will sit slightly lower than standard springs, somewhere between 1/2" and 1" lower. The competition springs cause the car to have a slightly lower the center of gravity and the competition springs are a stiffer spring, so...

Made from polyurethane, a bit more rigid and stiffer than our rubber insulators. Sold individually. Two required per vehicle. These are the coil spring insulators available from most Mustang/Cougar suppliers. Replaces Ford Part #: C4DZ-5415-A.

This Lower Ball Joint Dust Seal reproduction fits the 67, 68, 69, 70, 71, 72, and 73. Replaces Ford part # C7OZ-3105-A.Just and FYI, in order to install this boot, the entire lower ball joint must be removed from the lower control arm. That means grinding or drilling out the rivets, or removing bolts is so equipped.