All Available Parts - 1971 Mercury Cougar

Grade "B" 1971-72 driver side tail light lens. Grade B lens will have 1 or 2 blemishes which may include a small crack, chip, discoloration, or other defect. Replaces Ford part # D1WY-13450-B.

This is a tested original FoMoCo headlight switch that will work, there is no warranty. Used headlight switch for four headlight bulb systems and without vacuum headlight covers. Comes as shown, for 1967-68 Cougar applications you will need the headlight mounting bracket.Replaces Ford part # D2AB-11654, D3AB-11654, C5AB-11654

The D1WY-15A434-LSM LED Side Marker Light Adapter kit is required when the C9WY-13A366-AL or the TS-400 Sequential controller is installed with LED front turn signal and rear LED side marker bulbs on 1971 Cougars and other Ford vehicles with two rear side marker lights. An adapter is required for each rear side marker light (2 total). This adapter solves the problem where the side marker voltage feeds back through the front turn signal bulb when the running lights or headlights are turned on....

Over 100 total vacuum caps in 6 different sizes.

Just about the only possible reason to put this poor quality reproduction on your Cougar is that it is a good tool to put out engine fires. No Joke! If you happen to have an engine fire you can carefully open your hood, yank the blanket downward and smother the fire by pushing the blanket tight around the area that is burning. This can at least buy you time until a fire extinguisher is located. How do I know? I saved a very pristine 1974 XR7 a few years ago this way! This inexpensive product...

These original hood blanket clips grip much better than the reproductions. Usually there were 10-11 of these clips used but it can vary from car to car as they tended to be inconsistent at the factory on how many of the available holes they actually stuck a clip into. Sold Individually.

This is a good quality non-concours starter solenoid. Inexpensive replacement if you are not worried about being 100% correct. Disappointing quality, often will fail in less than a year, we recommend buying original FoMoCo. Replaces Ford part # B6AZ-11450-A, C7AZ-11450-A & D2AF-11450-A.

Reproduction rubber seal for the top of the brake fluid reservoir on the drum brake equipped Mercury Cougar or Ford Mustang. Also fits 1967-71 Ford or Mercury full and mid sized cars, and 1970-73 Maverick and Comet.  Replaces Ford part # C9AZ-2167-B.

Reproduction OEM style passenger side (right hand) exhaust hanger for the Mercury Cougar or Ford Mustang. You can hang up to a 3 inch diameter pipe with this unit.

Very nice reproduction of the drivers side muffler hanger as found on 1970 - 1973 Mercury Cougar and Ford Mustang. Every thing looks correct, riveted rubber and stamped steel brackets as original. You can hang up to a 3 inch pipe with this unit.

OEM Style Universal Exhaust Hanger Bracket 1967, 1968, 1969, 1970, 1971, 1972 and 1973 Mercury Cougar and Ford Mustang

Muffler mounting tabs for using factory Ford muffler hangers on aftermarket turbo style exhaust mufflers. These help achieve that concours look using a replacement muffler or mufflers. We recommend using your existing horse shoe shaped muffler hanger as a jig for locating these tabs prior to welding. These were copied from the original style tabs found on most 1968-73 Mercury Cougar and Ford Mustangs. 1967 cars and some Mustangs used a single transverse muffler behind the rear axles, these may...

Known to have been used on 1969-1970 air conditioning boxes to hold a vacuum hose to the actuator.  They can be screwed or bolted to the plenum.   Used plastic clip for the Mercury Cougar or Ford Mustang.

Located behind the dash to the right of the steering column.

Used plastic clip for the Mercury Cougar or Ford Mustang.

Used plastic clip for the Mercury Cougar or Ford Mustang. Inside diamenter = 1"

Used plastic clip for the Mercury Cougar or Ford Mustang

Used plastic clip for the Mercury Cougar or Ford Mustang.

Used plastic clip for the Mercury Cougar or Ford Mustang.

Used plastic clip for the Mercury Cougar or Ford Mustang.

Used to hold wiring to the back of the dash.

Used plastic clip for the Mercury Cougar or Ford Mustang. Cougar owner Mike B. shares that this clip was also used on 1970 Cobra Jets with Drag Pak option. Used to hold the wiring harness behind the factory oil cooler on the radiator core support.

Used plastic clip for the Mercury Cougar or Ford Mustang.

Used Trunk Light Wire Plastic Clip for the 1967 - 1973 Mercury Cougar

Used plastic clip for the Mercury Cougar or Ford Mustang.

Used wire loom plastic clip for the Mercury Cougar or Ford Mustang

Used plastic clip for the Mercury Cougar or Ford Mustang.

Keeps spark plug wires neat and orderly. Mounts on valve covers. Replaces Ford Part #: B8Q-12297-A.

Made of heat resistant black nylon. Keeps spark plug wires neat and orderly.

These Spark Plug Wire Separators are made of high-quality ABS plastic. Constructed to hold both standard 7mm and 8mm high-performance spark plug wires. Fits directly on valve cover clip. Available in blue, red and OE black.

Used plastic clip for the Mercury Cougar or Ford Mustang.

This "D" clip is larger than that found on the Mustangs and 1967 Cougar because it not only hung the wiring loom on the driver side of your engine compartment but also the vacuum lines going to the headlight switch. This clip is also found under the starter solenoid and under dash. We think that it is Ford part number 382184.

Used black plastic clip that goes onto the lower center of the firewall of any 1969 Cougar or Mustang. Also found on the back of the instrument cluster on the 71 - 73. We have found this to be one of three possible clips on the nail heads for the firewall for attaching wiring or speedometer cables. By far and away the most common clip is the one that looks like black plastic plumbers tape Ford part number 374320-S. This particular clip is the least common. There is a third clip that is...

Universal wire loom plastic clip for any application on Cougars or Mustangs, as well as many other models.5" x .26"

Reproduction diaphragm pump that mounts on the front all 67 - 73 Cougar or Mustang Autolite 2V carbs as well as 1967 Autolite 4V Carbs. With today's gas, these commonly fail, especially when sitting for extended periods of time. Complete failure will cause fuel leaks, but many times these will affect performance well before a leak actually starts. Good idea to replace every few years or if sitting for 6 months or more. Replaces Ford Part #: C4AZ-9B559-A.

Carburetor idle mixture screw caps like originally came on the cars from the factory. Exact reproduction of Ford part number C7AZ-9J500-A. This clip onto the idle mixture screws of any 1967-73 Autolite or Motor Craft carburetor 2100 or 4300. They also will fit the 429 Cobra Jet with Ford numbered Rochester Quadrajet carburetors in 1970-71. Sold as a PAIR.

New Street Avenger carburetor. The 350 CFM Street Avenger carburetor has great features such as optimized street calibrations...two vacuum ports for all necessary vacuum accessories, factory preset electric choke for easy startups, built-in fuel filters; and an included 3/8" fuel line connection so there are no unnecessary trips back to the parts store. Known to bolt in right out of the box. The Avenger series are the first carburetors to have a limited lifetime warranty. With a great...

Reproduction OE Steel Fuel Vapor Line for the 1970, 1971, 1972 and 1973 Mercury Cougar or Ford Mustang with 5/16" Fittings

Reproduction two hole fuel line grommet for the Mercury Cougar or Ford Mustang.

For use with your original Carter fuel pump on Cougars equipped with a BOSS 302, GT 390, 428 Cobra Jet or 429 Cobra Jet.

Replaceable filter which attaches to original fuel sending unit. Fits 3/8" tube. Replaces Ford part #: D1AZ-9A011-A.

New replacement carburetor mounting gasket for 1970-73 Ford 351C or 351 Cleveland engines. Mounts between the fuel pump housing and the engine.

Reproduction fuel pump for all 1970-73 Mercury Cougars and Ford Mustangs equipped with the 351 Cleveland engine. 

These are the straps that hold the gas tank in place. 2 required, sold individually.Replaces Ford part number D1ZZ-9092.

We prefer local pick-up only on these used 20 gallon fuel / gas tanks as we cannot ship anything that smells like fuel.

Quality U.S.A. made hose with concours repeating GAS markings. Also include OEM mounting hardware. Replaces Ford Part #: C7ZZ-9327-A. Check out our video on replacing the fuel system on a '68 Cougar

Fuel tank filler cap for all 1971-73 Mercury Cougars. All cars came with emission controls that vented fuel fumes into a charcoal canister. This is a non-vented gas cap.

OEM used not reproduction. Rust and damage free.

Reproduction fuel tank for the 71 - 73 Mercury Cougar. 20 gallon capacity, correct in every way. Beware that the Mustang tanks sold by most vendors has a different filler neck angle that doesn't fit Cougars. Replaces Ford part #: D1WY-9002-A ...

These are the straps that hold the gas tank in place. Sold as a pair.Replaces Ford part number D1ZZ-9092.

New replacement fuel filler neck screws for any 1971-73 Mercury Cougar or Ford Mustang. 5 needed per car, sold individually.

New replacement fuel filler neck screws for any 1971-73 Mercury Cougar or Ford Mustang. 5 needed per car, sold individually.

Reproduction anti rattler board - 1/8" panel board that prevents rattling noise. Installs on top of fuel tank on the side where the jack and spare tire mount. Measures 16" X 12"

Used rear window glass in grade "B" condition for the Mercury Cougar or Ford Mustang coupe. Nice clean piece of glass with only minor scratches.

Very good used door glass with no deep scratches (multiple faint scratches and water spots often will be present). Not perfect but the best you could expect to find from a 50 year old plus parts car and will of course be a better fit than repro. For those wanting Grade "A" glass, we recommend calling us so we can discuss with you the glass that we have available.Need a little help identifying some of the markings on your glass? Check out the Guide to Original Date Coded Glass - Mustang, Boss,...

Used grade "B" rear glass with the "Sun-X" green tint for the Mercury Cougar or Ford Mustang coupe. This is a nice clean piece of glass with only minor scratches. All air conditioning cars were supposed to always come with tinted glass, but we have documented cases of them coming with clear glass. Tinted glass was also available as an option in cars not equipped with A/C.

Brand new GREEN TINTED Tempered glass with no scratches or excuses. We guarantee this to be a perfect fit. This is a MUCH better way to go than peel and stick tint or the tint in an aerosol can... This glass does not have the faint Car-Lite markings in the corner but rather very bold

Brand new CLEAR Tempered glass with no scratches or excuses. We guarantee this to be a perfect fit. This is a MUCH better way to go than peel and stick tint or the tint in an aerosol can. This glass does not have the faint Car-Lite markings in the corner but rather very bold

Perfect fit for your Cougar or Mustang with just the right amount of tint to keep you cool. This unit also comes with the heat defroster.

This clear rear window glass with the heat defroster is a perfect fit for your Cougar or Mustang.

This is a replica white plastic washer bottle / reservoir with black top & cap (D1TZ-17632-A)

Made by Trico who made them originally for Ford. Replaces Ford part #: D1ZZ-17528-A. Sold individually

Original black windshield wiper blade holder. Fits any 1971-73 Mercury Cougar or Ford Mustang. Sold individually, two per car, 18" rubber wiper blade not included.Replaces Ford part #: D1AZ-17528-C or D3AZ-17528-A.

Injection molded high strength plastic connector for hoses leading to nozzles.Correct squared press-in fitting

Easy to install kit that converts your two speed wiper system to a variable speed system. These "off shore" units are spotty at best. We recommend our good used unit which you can get right here.

Original passenger side (right hand) wiper arm pulled off a 71 - 73 Mercury Cougar. Replaces Ford part #: D1ZZ-17526-A. Note: 1971 model year through 11/15/1970 uses the same wiper arm on both sides, which is the one used on the passenger side in the late 71 - 73 Cougars (Ford part #: D1ZZ-17526-A).

Original driver side (left hand) wiper arm pulled from a 71 - 73 mercury Cougar. Includes snap clip to hold the second arm in place. Replaces Ford part #: D1ZZ-17526-B. Note: 1971 model year through 11/15/1970 uses the same wiper arm on both sides, which is the one used on the passenger side in the late 71 - 73 Cougars (Part #: D1ZZ-17526-A).

CLEAR Glass without Shade; does not have Carlite logo, perfect fit. The most cost effective (and safest) way to ship these is when you buy several new pieces of glass and then we can drop ship them from the manufacturer via truck freight anywhere in the contiguous 48 for $110.00. We also sell the Window weld for the installation. BECAUSE OF THE HIGH COST OF SHIPPING, ALL WINDSHIELDS ARE AVAILABLE FOR DROP SHIP OR LOCAL PICK-UP ONLY. Our website is currently unable to accurately calculate truck...

Reproduction green tinted windshield that features a blue tinted band a crossed the top of the windshield. Not only will this unit look great, it will fit perfectly as well. Does not have Carlite logo. we also sell the Window weld for the installation. NOT for Sportsroof or Fastback models. BECAUSE OF THE HIGH COST OF SHIPPING, ALL WINDSHIELDS ARE AVAILABLE FOR DROP SHIP OR LOCAL PICK-UP ONLY. Our website is currently unable to accurately calculate truck freight costs, so don't be deceived by...

Plastic housings with brass nozzles. Note that you may need to adjust the nozzles to achieve the desired aim.

This is a reproduction of a later service replacement version of the windshield washer pump for the 1969 - 1973 Cougar and Mustang (and other Ford / Mercury models).The original Ford part was part number C9AZ-17664-C

Original FoMoCo used two speed windshield wiper motor for your 1971-73 Mercury Cougar or Ford Mustang. This used motor comes with wiring harness, for all 1971-73 Cougar and Mustangs. Motors are tested and guaranteed to work, 90 day warranty. Linkage arm for the 1971-73 installation, must be marked 1Z. Linkage arms sold separately. Ford part #s D1ZF-17504, D2ZF-17504, D1ZZ-17508-A

Linkage arm that attaches to the windshield wiper motor that is unique to the 1971-73 Mercury Cougar and Ford Mustang. These are marked 1Z, among other things the slot is specifically indexed for the 1971-73 Cougar and Mustang application. This is basically an installation kit that includes: linkage arm, flat bushing, wave washer, and nut. The order of installation is flat bushing, wave washer, linkage arm, and lastly the nut.

Electrical wiring pigtail for the windshield wiper motors on any 71 - 73 Mercury Cougar or Ford Mustang. Plug with correct color wires and an adequate amount of wire length to make a repair or splice onto the newer motors without plugs.

Reproduction wiper arms for the 71 - 73 Cougar or Mustang. Sold as a pair.Replaces For Part number D1ZZ-17526-B

Reproduction keeper clip that attaches to the secondary articulating stabilizer arm and slides into place to secure the pin that holds the arm.

The hinges on these original arms tend to get worn out which will cause irregular movement and can eventually burn up your wiper motor or bind up the linkage. If your wipers do not move in tandem

Used windshield support bracket for any 1971-73 Mercury Cougar or Ford Mustang. One per side

Original FoMoCo used two speed windshield wiper motor mounting bracket for your 1971-73 Mercury Cougar or Ford Mustang. This used bracket comes with grommet for all 1971-73 Cougar and Mustangs. Ford part # D1ZZ-17496-B.

Good used D0OZ-17C583-A adjustable windshield wiper stop, as found on any 1971-73 Mercury Cougar, 1971-73 Ford Mustang, 1970-71 Ford Torino, or 1970-71 Mercury Cyclone. Cougar and Mustang use one of these in the center, not sure about the Torino.Will need new rubber dipped like OEM Ford. Replaces Ford part number D0OZ-17C583-A.

Unlike the 1968 Cougar headlight switch, the 1967 and 1971-73 version does not have the three vacuum ports connected to it. Don't be fooled . . . Most vendors will sell you a Mustang switch and tell you it is the same. Visually it may look the same but internally it has a circuit breaker designed for a two headlight system, the Cougar has four headlights. If you only use the low beams you would be fine but if you have all four lights on you will soon experience a blackout. If your original...

*NOTE* If you're going to make your car concours correct, you need to specify which year you have (bulbs are date marked), otherwise we'll just send you any random FoMoCo bulb.Please note that we are out of date coded bulbs for 1969 and up.  If ordering online, leave the info in the comments section of your order. If your order is being done over the phone, be sure our rep knows which year you have. This is the much harder to find outer, low beam lamp distinguished by the number 2 at 12...

This is the correct ring for all years 1967 - 1973 high beam or low beam. No dings, gouges or broken spot welds. It is held in place by a spring and two screws. Four rings required per car, sold individually. Made from stainless steel, these clean up nicely with fine steel wool. Ford part number C7AZ-13015-B. Below is a comparison of the Repro and Used/NOS Headlight rings: Click on images to enlarge. The above picture shows the Used (top left), NOS (center), and Repro (bottom right) Headlight...

Reproduction Headlight / Tilt Column Vacuum Check Valve for the 1967 to 1973 Mercury Cougar, Cyclone, Marquis, Ford Torino, Ranchero, Galaxie, LTD, Thunderbird, Lincoln Continental and Mark III. NOTE: The direction of flow is up through the dual ports and out through the single port.  For more in depth detail on this reproduction, see pictures below. *NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've...

These are the correct ring for all years 1967 - 1973 high beam or low beam. No dings, gouges or broken spot welds. They are held in place by a spring and two screws. Made from stainless steel, these clean up nicely with fine steel wool. Ford part number C7AZ-13015-B. Below is a comparison of the Repro and Used/NOS Headlight rings: Click on images to enlarge. The above picture shows the Used (top left), NOS (center), and Repro (bottom right) Headlight rings side by side. If you look close at...

Our best grille center, not perfect but very close. Often you will see minor pitting on the very bottom where the grille meets the bumper. This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit of 50% of our web price for parts delivered in hand or by carrier to our Brooks, Oregon location. If you're not interested in store credit, just shoot us an email and we will let you know if it's is...

This body part is painted body color and mounts vertically on either side of the center grille. Grade "A" part with no rust or dents, ready to paint and install. This is a 3 piece set, which includes: D1WY-8282-A and D1WY-13B116-A. Passenger side filler between grille and headlight assembly. Does not include chrome trim or hood rubber bumper on top.

Used headlight wiring harness for either side of the Mercury Cougar. This harness is the sub-harness that connects your headlights to the under hood harness. The Cougar uses one per side and they are identical. Sold individually.Ford part # D1WY-13076-A.

Used A grade, driver side or left hand side headlight bucket or housing. Made of fiberglass, which is fragile. Our A grade housings may a minor chip, but will not have damage where the housing bolts to the car, or where the headlights mount. Ford part number D1WB-13101.

Used A grade, passenger side or right hand side headlight bucket or housing. Made of fiberglass, which is fragile. Our A grade housings may a minor chip, but will not have damage where the housing bolts to the car, or where the headlights mount. Ford part number D1WB-13099.

Used Grade B passenger side or right hand side headlight bucket or housing. Made of fiberglass, which is fragile. Our B grade housings will have at least two defects, one of which will be a break where the housing mounts to the car. A bolt with over sized washers remedies these problems. Other defects could be a crack or chip in the fiberglass. We will often substitute the 1973 headlight housing, which was a service replacement part for 1971-72 Cougars.Ford part number D1WB-13099. ...

Used Grade B driver side or left hand side headlight bucket or housing. Made of fiberglass, which is fragile. Our B grade housings will have at least two defects, one of which will be a break where the housing mounts to the car. A bolt with over sized washers remedies these problems. Other defects could be a crack or chip in the fiberglass. We will often substitute the 1973 headlight housing, which was a service replacement part for 1971-72 Cougars.Ford part number D1WB-13101. ...

Here is our used driver (left hand) side hood lip moulding / trim in grade "B" condition for your Mercury Cougar. This is a tough little unit to find in NOS form or grade "A" condition. Most of these will come with some pitting or minor scratches in the chrome, but will look great on your mid-level daily driver. You can save quite a bit of cash-o-la if you purchase this item in our 3 piece set that comes with the center and passenger side mouldings. If you choose to purchase the set, you will...

Here is our used passenger (right hand) side hood lip moulding / trim in grade "B" condition for your Mercury Cougar. This is a tough little unit to find in NOS form or grade "A" condition. Most of these will come with some pitting or minor scratches in the chrome, but will look great on your mid-level daily driver. You can save quite a bit of cash-o-la if you purchase this item in our 3 piece set that comes with the center and driver side mouldings. If you choose to purchase the set, you will...

Here is our used center hood lip moulding / trim in grade "B" condition for your Mercury Cougar. This is a tough little unit to find in NOS form or grade "A" condition. Most of these will come with some pitting or minor scratches in the chrome, but will look great on your mid-level daily driver. You can save quite a bit of cash-o-la if you purchase this item in our 3 piece set that comes with the driver and passenger side mouldings. If you choose to purchase the set, you will need to make sure...

Here is our used hood lip moulding / trim 3 piece set in grade "B" condition for your Mercury Cougar. These are tough little units to find in NOS form or grade "A" condition. Most of these will come with some pitting or minor scratches in the chrome, but will look great on your mid-level daily driver. When you buy these in a set, you will save a good sized chunk of your hard earned cash-o-la! -Center Moulding: Mercury part # D1WY-16958-A, Mercury casting # D1WB-16958-AA.-Driver (left hand)...

Chrome passenger side (right hand) bezel that wraps around the outside of the front turn signal lens on the 1971 or 1972 Mercury Cougar. This bezel will be blemished. Blemishes could include cracks, pitting, or bends. Will not be missing any pieces. Ford part # D1WB-13236-AA.*NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's and is the designer of all of our solid state...