All Available Parts - 1971 Mercury Cougar

The Mini Relay Kit has everything you need to add relays to your headlight circuit - without cutting your wiring harness. It is equivalent to installing relays into your main harness like it was done for years, but requires no modification to the wiring harness. The differences between this kit and the full kit are redundancy and controller size. This kit has only one controller with two relays designed to handle up to a maximum of 200 combined watts and uses a wiring harness to control...

Used random brand 4001 high beam headlight for the Mercury Cougar. High beam headlights are distinguished by the number 1 at 12 o'clock position and the 2 prong connection on the back. We guarantee these units to work. Basic Ford part # 13007-B.

Reproduction replacement halogen bulb for your headlights. This is a clear bulb, "natural white" alternative to the "cool white" bulbs included in our halogen headlight conversion kit. 55 Watt Xenon Halogen H4/9003 bulb. Sold Individually.

Reproduction pair of halogen headlights for any 67 - 73 Cougar or Mustang. These bulbs work for both high and low beam, you simply need to bend one of the tabs back for high beam (see photo above). Keep in mind that you will need a headlight relay kit when installing halogen headlights on your car.  Benefits of switching to halogen bulbs: Brighter lightDramatically improves driver visionOptical lens for a powerful beamLong range high powered lightsCrystal clear glass face with H4 halogen...

NOTE: WILL NOT FIT 69-73 COUGAR WITHOUT MODIFICATION TO THE CORE SUPPORT OR SPACING THE HEADLIGHT FORWARD APROXIMATELY 1/4" Reproduction complete set of halogen projection headlight bulbs for your 67 - 73 Cougar or 69 Mustang. Integrating the newest modern projection headlight technology into a slim compact bulb, these headlights will fit right into your existing headlight bucket. Each kit comes with the proper wiring adapters so all you need to do is plug one end into the bulb and...

Complete set of halogen projection headlight bulbs for your 67 - 73 Cougar or 1969 Mustang. Integrating the newest modern projection headlight technology into a slim compact bulb, these headlights will fit right into your existing headlight bucket. Each kit comes with the proper wiring adapters so all you need to do is plug one end into the bulb and the other end into your headlight harness.NOTE: From the factory, Ford made the alignment tabs different passenger vs driver side...

This kit is what we recommend to fully convert your 1971 Cougar over to LED Plasma exterior lights. Our WCCC brand LED lights are amongst the brightest on the market and have been specifically engineered with the nuances of the Mercury Cougar sequential system in mind. Keep in mind that over the years folks have become accustomed to very BRIGHT tail lights in traffic and the old incandescent bulbs are not only dim, but they take time to fully illuminate and a split second can make all the...

This is a restored taillight housing assembled in-house. Complete assembly with new sockets and repaired pigtails in place. Reflective background has been re-painted silver. No major cracks or chips, every unit is thoroughly tested. NOTE: 71-72 housings will not work on the 73, and vice versa. While you're at it, you can grab some new gaskets here. Ford Part Number: D1WB-13441-AA ...

This is a restored taillight housing assembled in-house. Complete assembly with new sockets and repaired pigtails in place. Reflective background has been re-painted silver. No major cracks or chips, every unit is thoroughly tested. NOTE: 71-72 housings will not work on the 73, and vice versa. While you're at it, you can grab some new gaskets here. Ford Part Number: D1WB-13440-AA ...

Used passenger side (right hand) rear marker light bezel for any 1971-73 Mercury Cougar. Originally painted body color, flush mounted to the passenger side rear quarter panel. Has two attaching studs, and sometimes one locating stud. We often times find that the locating stud is broken or cut off. You will want to cut the corner stud off if using the available reproduction Mustang red rear reflectors. All of our bezels will have the 2 larger studs intact. See related items for new lenses and...

Used driver side (left hand) rear marker light bezel for any 1971-73 Mercury Cougar. Originally painted body color, flush mounted to the passenger side rear quarter panel. Has two attaching studs, and sometimes one locating stud. We often times find that the locating stud is broken or cut off. You will want to cut the corner stud off if using the available reproduction Mustang red rear reflectors. All of our bezels will have the 2 larger studs intact. See related items for new lenses and...

Reproduction master power window switch that goes along with the power window conversion kits. Keep in mind we will buy your old usable factory parts. You might be surprised what those left over clips and wiring harnesses are worth!  Installing this master switch allows you to keep the original look of the crank handles, but allows the driver to control all four windows. All wiring and connectors are included.  ...

This two part black box is what encapsulates your sequential unit for all years 1969-1973. This of course will work with our reproduction sequential unit as well. This box was designed hang from a hook that is welded to the trunk floor just behind the driver side wheel well. *NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's and is the designer of all of our solid state...

Good used part cut from the trunk of a 69-73 Mercury Cougar. This hook is concealed under the trunk mat and suspends the sequential unit over the trunk drop off area on the driver side. *NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's and is the designer of all of our solid state sequential systems. There is no question he cannot answer! Here is a link to a great source of...

This new version sequential box works with either standard or plasma LED bulbs NOTE: Although your existing emergency flasher might work just fine with the new sequential unit, it is highly recommended that you also use the same updated electronic sequential flasher in its place to guarantee proper operation. This is a direct fit replacement, just pop open your black plastic box located in the driver side trunk drop off and plug it in. Your January 1970 and newer Cougar will have...

This is a "better quality" non-concours starter solenoid. It's just one step above our "generic" solenoid also listed on our site. An inexpensive replacement if you are not worried about being 100% correct. More often than not, these lower quality solenoids fail within a year or two so we always recommend buying original FoMoCo. Replaces Ford part # B6AZ-11450-A, C7AZ-11450-A & D2AF-11450-A.Cougar Applications:1967 Mercury Cougar1968 Mercury Cougar1969 Mercury Cougar1970 Mercury...

This Autolite capacitor is stamped with part number C6OA-18832-A. It attaches to one of the lugs on the voltage regulator, bullet lead plugs into wiring harness. Sometimes called a radio ignition interference suppressor. About 1-15/16" inches long. This is one of those small detail items that judges like. All Ford and Mercury vehicles from 1966-1971 used this "Autolite" marked capacitor when a radio was installed by the factory. Starting in 1972 there is a Motorcraft version which has a...

Electrical junction block for use on 1971-73 XR7 models or 1971-73 Ford Mustang with options such as convertible, power seat, power windows, or rear defog. This combination insulator / junction block is for securing a circuit breaker, and mounts near the starter solenoid. Made from black Bake-O-Lite, Grade A used, may have some discoloring, but not damage.Replaces Ford part number D0SB-14448-A or D0SZ-14448-A.

Electrical junction block for use on 1971-73 XR7 models or 1971-73 Ford Mustang with options such as convertible, power seat, power windows, or rear defog. This combination insulator / junction block is for securing a circuit breaker, and mounts near the starter solenoid. Made from black Bake-O-Lite, Grade B, these will have some chipping or cracking present. Replaces Ford part number D0SB-14448-A or D0SZ-14448-A.

Finally a fast easy way to hook up the Pertronix Ignitor©! The Ignition Power Relay installs next to the starter solenoid with a supplied self-drilling, self tapping screw. Each wire is the right length and comes with the correctly sized terminal already Installed. Simply connect two wires at the solenoid and connect the Ignitor to the red power wire. The Pertronix Ignitor© is a 12 volt device that must be powered during crank and run. Many installers mistake the coil positive for a 12 volt...

Reproduction 2 speed windshield wiper switch for the Mercury Cougar or Ford Mustang. These "off shore" units are spotty at best.Replaces Ford Part #: D1ZZ-17553 or D1ZZ-17553-A

Oil pressure switch with press on wiring connector. 1967-73 Mercury Cougar and Ford Mustang. This is the warning light style of sending unit. Cougar body code 65A and 65C, excludes Eliminator. Additionally this sending unit also fits 1970 and newer Ford Maverick and Mercury Comet, 1968-69 Lincoln with 460 engines, and 1967-71 mid sized Ford and Mercury cars such as Cyclone, Fairlane, and Torino.Check out the video below on our new gauge tester: ...

Used switch panel with 3 switches for all 1971-73 Mercury XR7  with convertible tops. Inspected and tested switch panel for COURTESY - MAP - TOP. All three switched prove will function and operate. Toggle tips included. Do you have extra, or non working 1971-73 XR7 convertible top switch assemblies? As long as the circuit board part of it isn't damaged we will buy them for $30. Switch assembly must be stamped D1WB-15668-AA on the reverse. *Note - Excludes Non - XR7 model...

Tested and working used 2 speed windshield wiper switch for any 1971-73 Mercury Cougar and Ford Mustang. Replaces Ford part number D1ZB-17A553.

Used seat back release relay for the 71 - 73 Cougar or Mustang. Located on the relay panel behind the glove box. Ford part number D1ZB-14C690-AA

Good original used toggle tip for the 1971 - 1973 Mercury Cougar XR7

Used driver side turn signal / parking lamp wiring harness with socket for the 1971 - 1973 Mercury Cougar.Ford part number D2WB-13234-AA

Used passenger side turn signal / parking lamp wiring harness with socket for the 1971 - 1973 Mercury Cougar.Ford part number D2WB-13235-AA

Used lead wire harness that runs from the white plug at the cowl to the throttle positioning sensor on the 71 - 73 Cougar or Mustang.Harness is red with yellow hash marks.

Used engine lift hook or hoist bracket for all 1970-73 351C engines from any Mercury Cougar or Ford Mustang. Ambidextrous, fits either side as long as you use factory cast iron exhaust manifolds. H code 351C-2V and M or Q code 351C-4V engines. The factory used these hooks for installation of the engines into the cars on the assembly line. Nice detail to include for judged shows, many of these have been lost for various reasons. Sold individually, two needed per car, one on each side.We also...

NOTE: WE SUGGEST LOCAL PICK UP ONLY FOR CORE ENGINE BLOCKS BECAUSE WE CANNOT GUARANTEE BLOCKS WILL NOT HAVE CRACKS INTERNALLY. Long block, factory H code 351-2V V-8 engine. 351 Cleveland engine rated at 240 Hp with 9.5:1 compression ratio in 1971. Likely 0.030" bored motor that may or may not have been in running condition when pulled. Guaranteed to be rebuildable. Complete engine less carburetor, exhaust manifolds, fan, distributor, accessories, pulleys, and flex plate. Intake...

NOTE: WE SUGGEST LOCAL PICK UP ONLY FOR CORE ENGINE BLOCKS BECAUSE WE CANNOT GUARANTEE BLOCKS WILL NOT HAVE CRACKS INTERNALLY. Long block, factory M code 351-4V V-8 engine. 351 Cleveland engine rated at 285 Hp with 10.7:1 compression ratio in 1971. Likely 0.030" bored motor that may or may not have been in running condition when pulled. Guaranteed to be rebuildable. Complete engine less carburetor, exhaust manifolds, fan, distributor, accessories, pulleys, and flex plate. Intake manifold and...

These replacement "Yellowtop" ignition coils are copies of the original. Nice reproduction cosmetically and functionally. This is a very prominent piece and a must have when trying to detail your engine compartment properly. Replaces Ford part # B6A-12029-B.   Note, no decals are included. Check the website in related items.

Reproduction distributor cap for the 1967 - 1973 Mercury Cougar or Ford Mustang 

A needed part for giving your car a tune-up.

Reproduction Distributor Condensor for the 1967 - 1973 Mercury Cougar and Ford Mustang

Correct Autolite 24 spark plugs for all 1970-73 351 Cleveland engines. This is what Ford installed originally from the factory. Typically these should have a electrode gap of 0.035", with either stock points or Pertronix ignition systems. Sold individually.

Correct Autolite 45 spark plugs for all 1967-73 289/302/351W/390/428CJ engines. This is what Ford installed originally from the factory. BF32 crosses over to this spark plug. Typically these should have a electrode gap of 0.035", with either stock points or Pertronix ignition systems. Sold individually.

C8AF-12A022-A For all 1967 - 71 V-8 distributors. Concours correct head stamping. Brass plug for the stock Autolite distributors. Installs as shown.

Reproduction single port vacuum advance for most all 1967-71 Ford V-8 engines. Fits Ford's brand of Autolite and Motorcraft distributors found on all 1967-71 Mercury Cougar and V-8 Ford Mustangs.

This little device may not appear to be all that important, but it has a big job to do when your engine gets too hot. The threaded end looks a bit like an engine temperature sensor, and that's because it is. It's normally mounted on the intake manifold or engine block where it can sense coolant temperature.The three ports at the other end are for vacuum connections. One goes to manifold vacuum, another to carburetor vacuum, and the third goes to the vacuum advance on the distributor. At normal...

Ignitor 1 by Pertronix, effectively replaces your points and condenser from your Distributor. Works in all Ford Autolite distributors found in 1967-73 Mercury Cougar and V8 Mustangs with single point distributors. This is also called an electronic ignition conversion. There is also an upgraded Ignitor II available. -50F To 300F Working Temperature Range, 0-15,000 Rpm Range, This Easy To Install And Maintenance Free Electronic Ignition System Features Solid-State Electronics And Rotating Cobalt...

Ignitor II by Pertronix, effectively replaces your points and condenser from your Distributor. Works in all Ford Autolite distributors found in 1967-73 Mercury Cougar and V8 Mustangs with single point distributors. This is also called an electronic ignition conversion. Adaptive Dwell Control -  Dwell increases with RPM to provide an average of 4 times the available energy between 3000 and 5000 RPM and twice the available voltage at the plug. -50F To 300F Working Temperature Range,...

Powerful oil filled coil that generates 40,000 volts, designed to work with the either of our Pertronix Ignitors. Sold in black or chrome. *Note - This coil is not necessarily needed with the Pertronix Ignitors, the stock Ford coil works fine for most applications.

Powerful oil filled coil that generates 40,000 volts, designed to work with the either of our Pertronix Ignitors. Sold in black or chrome. *Note - This coil is not necessarily needed with the Pertronix Ignitors, the stock Ford coil works fine for most applications.

Concours correct Autolite spark plug wires for any 1971 Mercury Cougar Eliminator or Ford Mustang with 351C engines. Black wires with 'Autolite', 'radio resistance', cylinder numbers individually imprinted, and dated 2Q70 (second quarter 1970) on the 7mm wires. Orange spark plug boots on this set.

Concours correct Autolite spark plug wires for any 1971 Mercury Cougar Eliminator or Ford Mustang with 429CJ engines. Black wires with 'Autolite', 'radio resistance', cylinder numbers individually imprinted, and dated 2Q70 (second quarter 1970) on the 7mm wires. Orange spark plug boots on this set.

Ford FE distributor shaft to engine block gasket, made of rubber. Fits all FE or 352, 360, 390, 410, 427, 428 engines. 1958-76. This is a tapered rubber washer. Will not fit small block Windsor or Cleveland engines. Ford part number B8A-12143-A.

New rubber "O" ring for Ford V-8 distributors from 289/302/351W/351C/429 engines.

Pertronix brand 7mm spark plug wires. These are performance oriented wires compared to the concours spark plug wires. For any 1967-73 Mercury Cougar and Ford with 289 or 302 engines. Black wires and boots, quality spark plug wires taylor made for the small block Ford engines. Recommended by Pertronix for use with the Flame Thrower coils.

Pertronix brand 7mm spark plug wires. These are performance oriented wires compared to the concours spark plug wires. For any 1967-73 Mercury Cougar and Ford with 351 - 390- 428 - 429 engines. Black wires and boots, quality spark plug wires taylor made for 351 engines and the big block Ford engines. Recommended by Pertronix for use with the Flame Thrower coils.

The Proper ignition advance curve is vital for maximum performance, economy (gas mileage) and drive-ability. Ford / Mercury owners had few acceptable choices with regard to adjusting the vacuum curve with their OEM distributor. You could fumble with the stock washers, fiber stops and springs (a hit-or-miss exercise in frustration!) or you could spend the money on an adjustable after market vacuum advance that looks completely out of place and cost you major judging points. This works on any...

Replaces Ford Part Number: B7A-12200-A / DR-5 And C5TZ-12200-A / DR-87 (Service Replacement)

Reproduction coil mounting bracket. The manufacturer claims it fits all cars 1967-73. We happen to know that there are no less than 4 different versions of factory Ford coil brackets used on 1967-73 Mercury Cougar and Ford Mustangs and literally all other Ford cars and trucks. Some have the coil on top of the intake manifold, while some years and engines have the coil mounted to the front of one of the cylinder heads. To our knowledge this is the only reproduction style on the...

Reproduction replacement hold down clamp for the distributor on any 67 - 73 Cougar or Mustang. Sold individually, 2 needed per car.

Used jumper wire with correct ends for doubling back on the tachometer leads from the under dash harness. Works for all generations 1967-68, 1969-70, and 1971-73 Ford anything and Mercury, and Mercury Cougar with factory tachometers. If your tachometer goes bad, you will not start or keep your engine running. Good for bypassing tachometers for testing and getting home. Keep in your glove compartment or tool box. Mostly the wire color is red, but sometimes there will be other colors.

This plug will work on your 69 - 73 Standard or XR7 as well as the 69 - 73 Mustang. This plug housing is used to connect the under dash main loom to the gauge cluster.

Rebuilt quartz movement clock for the 1971 - 1973 Cougar or Mustang. Quartz movement clocks have second hands that click around, original clocks had a constant sweep of the second hand.

This bracket connects the battery hold down clamp to the fender apron to stop the battery from rocking from side to side. Most cars are missing this crucial part to stabilize the battery. Original used bracket, not reproduction. Replaces Ford Part #: D0OZ-10757-A.

Vinyl dipped. Clip is used to hold wiring away from hot engine. Also found on trunk floor.

Insulator for mounting the ammeter on any 1969-73 Mercury Cougar or Ford Mustang with factory ammeter in gauge cluster. Also used on other Ford cars with ammeter. Casting number C9ZF-10C914. Ford Part # C9ZZ-10C914-A

Used distributor clamp with bolt, for any 260 / 289 / 302 / 351W / 351C / 429CJ built from 1963-1973. May come with either an original used bolt or the new bolt made by AMK Products. Ford part number C3AZ-12270-A.

Original distributor vacuum advance control valve, also called a ported vacuum switch (PVS) valve, that was installed on all Ford models including Mercury Cougar, Ford Mustang, and Torino starting in 1967. This is a used original pot metal and brass part. It has the FORD oval logo and part number D0AE-A casting.This casting number is correct for all 1970 1971 1972 and 1973 Fords and Mercury. It was used on all engine options including 302 351C 351W 429 and 429CJ models. Because of the heavy...

Exact copy reproduction concourse correct distributor cap with raised Autolite logo. Good for all 67 - 73 Cougars and Mustangs. A must have for anyone building a show car.

Distributor hold down bolt. All V-8 engines.1967-73 Mercury Cougar and Ford Mustang. 5/16 x 7/8" bolt, 1/2' hex head.

Used 1969 351W coil mounting bracket. This version of the bracket is specific on the 351W and allows extra room for the oil dipstick. We happen to know that there are no less than 4 different versions of factory Ford coil brackets used on 1967-73 Mercury Cougar and Ford Mustangs and literally all other Ford cars and trucks. Some have the coil on top of the intake manifold, while some years and engines have the coil mounted to the front of one of the cylinder heads. Listed in the...

Concours vacuum hose kit with colored stripes. Multiple pieces, connects carburetor, distributor, and thermal vacuum switch on the water neck. Fits all 1971 Mercury Cougar or Ford Mustang with 429CJ engines. Distributor vacuum advance units with single nipple connections. Often times it is the ones with manual transmissions, but not always.

Concours vacuum hose kit with colored stripes. Multiple pieces, connects carburetor, distributor, and thermal vacuum switch on the water neck. Fits all 1971 Mercury Cougar or Ford Mustang with 429CJ engines. Distributor vacuum advance units with dual nipple connections. Often times it is the ones with automatic transmissions, but not always.

Reproduction dual port vacuum advance for most all 1968-70 Ford V-8 engines. Very close replica of the factory installed vacuum advance. This version has two pressed in brass fittings for vacuum hoses. This working vacuum advance will need to have your threaded plug installed in the port end. OEM Ford units had gold colored bands instead of this silver band as shown. This unit very closely matches the 1970 vacuum advance, the earlier vacuum advances had one of the vacuum fittings that screwed...

Used coil mounting bracket. This version of the bracket is probably the most common. We happen to know that there are no less than 4 different versions of factory Ford coil brackets used on 1967-73 Mercury Cougar and Ford Mustangs and literally all other Ford cars and trucks. Some have the coil on top of the intake manifold, while some years and engines have the coil mounted to the front of one of the cylinder heads. This version has the notch as shown. We know that this version was used on...

New Old Stock distributor cam and weight assembly for many Autolite and Motorcraft distributors. This is cam #107 or DF-342, single points cam with weights marked 13L and 18L from the top. Factory used on small block and FE distributors.  Ford part number C5AZ-12210-A.

New Old Stock distributor cam and weight assembly for many Autolite and Motorcraft distributors. This is cam #108 or DF-343, single points cam with weights marked 10L and 15L from the top. Factory used on small block and FE distributors.   Ford part number C5AZ-12210-B.

New Old Stock Ford FE distributor shaft to engine block gasket, made of rubber. Fits all FE or 352, 360, 390, 410, 427, 428 engines. 1958-76. This is a tapered rubber washer. Will not fit small block Windsor or Cleveland engines. Ford part number B8A-12143-A.

New Old Stock Ford small block Ford distributor shaft to engine block gasket, made of rubber. Fits all 260, 289, 302, 351w, 351c engines. 1959-76. This is a "O" ring rubber washer. Will not fit big block FE, 360, 390, 410, 427, 428 engines. Ford part number B9TF-12143-A.

Reproduction upper distributor bushing for 1969-73 351W, 351C, 429, and 460 Ford V-8 engines. * Note - 260/ 289 / 302 / 352 / 390 / 410 / 427 / 428 engines, all used a different upper bushing. See related items for that listing. Replaces Ford part number  C5AZ-12120-A. We measure 0. O.D., 0." I.D., and 1.750 long.

Key stock for 1967-73 Ford V-8 engines 3/16" square straight keys. Ships in 4 inch lengths, cut to fit the different applications. Common sizes 289/302 1-13/32", 351 1-3/4", etc.

D0AE-6316-A All 1970-73 351C-2V and only the 1970 M code 351C-4V engine. The 1970-73 351 Cleveland harmonic balancers all have 4 bolt holes for attaching the crankshaft pulley. Outside diameter is approximately 6-1/2 inches. Ford master part number DOAZ-6316-A. Crank shaft balancer, crankshaft dampener, harmonic balancer. There is a $50 core charge for this part.*Note - Excludes 1971 and later 351-4V engines. **Note - When ordering double check that you have a 351 Cleveland engine. It is not...

D0AE-6316-A All 1970-73 Mercury Cougar 351C-2V engines, and only the 1970 M code 351C-4V engine. The 1970-73 351 Cleveland harmonic balancers all have 4 bolt holes for attaching the crankshaft pulley. We save the very best used harmonic balancers, those that do not actually need rebuilding. Outside diameter is approximately 6-1/2 inches. Ford master part number DOAZ-6316-A. Crank shaft balancer, crankshaft dampener, harmonic balancer. Price includes $55 core charge. Refundable $50.00 core...

Includes all 1971 M code and 1972 - 1973 Q code 351-4V or 351 Cobra Jet Mercury Cougar engines. Outside diameter is approximately 6-1/2 inches, and 1-1/2 inches thick. 1971-73 351-4V Cleveland have specific balancers, and are different than 1970 351C 4 barrel engines, please identify your engine and verify your balancer numbers. Has the timing marks on rim. Core charge is refundable when rebuildable D1ZE-6316-AA or D1ZE-6316-AB harmonic balancer is received by WCCC. Ford part #...

Includes all 1971 M code and 1972-73 Q code 351-4V or 351 Cobra Jet Mercury Cougar engines. Outside diameter is approximately 6-1/2 inches, and 1-1/2 inches thick. 1971-73 351-4V Cleveland have specific balancers, and are different than 1970 351C 4 barrel engines, please identify your engine and verify your balancer numbers. Has the timing marks on rim. The rubber in this used balancer will be the original and will not be showing cracks or signs of having shifted. This good quality used...

Ford casting number D0OE-6316-B Includes all 1970-71 J or C code 429CJ engines. The D0OE-6316-B harmonic balancer is identified by the 4 bolt holes for attaching the crankshaft pulley. Outside diameter is approximately 6-5/8 inches, and 1-3/8 inches thick. Ford part number D0OZ-6316-B. Has the timing marks on rim.  Core charge is refundable when rebuildable D0OE-6316-B harmonic balancer is received by WCCC.Click on images to enlarge. This is a picture of a 40 year old piece of rubber...

Ford casting number D0OE-6316-B Includes all 1970-71 J or C code 429CJ engines. The D0OE-6316-B harmonic balancer is identified by the 4 bolt holes for attaching the crankshaft pulley. Outside diameter is approximately 6-5/8 inches, and 1-3/8 inches thick. Ford part number D0OZ-6316-B. Has the timing marks on rim. The rubber in this used balancer will be the original and will not be showing cracks or signs of having shifted. This good quality used balancer is a good option for those wanting to...

Used bolt and washer for attaching the crankshaft balancer or damper to the crank shaft. 15/16 inch hex head with 5/8-18 threads and 1.75 inches long. Basically fits all Mercury Cougar engines except the 1971 429 Cobra Jets engines. Fits 1967-73 289, 302, Boss 302, 351W, 351C, 390, 427, and 428CJ engines.Torque specifications for this bolt are 70-90 foot pounds.*Note does not fit 429 or 460 V8 engines or any 6 cylinder engines.

Used intake manifold bolt for the Mercury Cougar or Ford Mustang equipped with the 351C engine. This item is sold individually.Ford part # 56145-S.

D1AE-9425-DA Cast iron intake manifold used on all 1971-72 H code 351-2V engines in a Mercury Cougar or Ford Mustang. Stock 2 barrel intake manifold. Take off manifold with correct casting number of D1AE-9425-DA. Intake shipped bare, less choke stove, carburetor studs, heater tube, vacuum fittings, and water neck where applicable. Ford master part number D1AZ-9424-D. *Installation Tip - A 1 inch aluminum spacer plate with PCV provision is needed for proper air cleaner clearance. *Note - 351...

D0AE-9425-E, -H, or -L Cast iron intake manifold used on all 1970-71 M code 351-4V engines in a Mercury Cougar or Ford Mustang. Stock 4 barrel intake manifold. Take off manifold with correct casting number of D0AE-9425-E, -H, or -L . Intake shipped bare, less choke stove, carburetor studs, heater tube, vacuum fittings, and water neck where applicable. Ford master part number D0AZ-9424-C. *Note - 351 Cleveland engines only.

Reproduction intake manifold valley pan for the Mercury Cougar or Ford Mustang equipped with the 351 Cleveland engine with the 2V (2 barrel) heads.

New gaskets for installing your intake manifold. This is the Felpro branded gasket. Fits all 1970-73 Ford 351C engines with 2 barrel intake manifolds 1969-70 Mercury Cougar and Ford Mustang with 351C-2V engines. This gasket set includes a metal pan gasket.Any doubts? 351 Windsor engines have 6 bolts holding the valve covers in place. 351 Cleveland engines have 8 bolts holding down the valve covers.*Note - Excludes 351W engines. *Note - Excludes 351C-4V Cleveland engines. ...

New gaskets for installing your intake manifold. This is the Felpro branded gasket. Fits all 1970-73 Ford 351C engines with 4 barrel intake manifolds 1969-70 Mercury Cougar and Ford Mustang with 351C-4V engines. This gasket set includes a metal valley pan.Any doubts? 351 Windsor engines have 6 bolts holding the valve covers in place. 351 Cleveland engines have 8 bolts holding down the valve covers.*Note - Excludes 351W engines. *Note - Excludes 351C-2V Cleveland engines. ...

This is a set of four 7/16 nuts that are used to secure the carburetor to the intake manifold. If you need to replace your rusty old studs, we also carry an eight piece kit that contains the studs and nuts. 

This is the complete eight piece kit that includes four 7/16 nuts and four studs (1 3/8") which are double threaded. One end is fine threaded to accommodate the installation nuts, and the other end has the course threads needed to screw into the intake manifold. This is the kit used to install carbs with NO spacer.

This is the complete eight piece kit that includes four 7/16 nuts and four double threaded studs (1 3/4"). One end of the stud is fine threaded to accommodate the installation nuts, and the other end has the course threads needed to screw into the intake manifold. This is the kit used to install carbs with 1/4" to 3/8" spacers.

Set of 20 bolts for the intake manifold on any 1970-71 Ford 429 Cobra Jet engine. 429CJ engines were optional in only in 1971 on Mercury Cougar and Ford Mustangs. Available in 1970 on B body Torino, Cyclone, Ranchero, Fairlane. *Note - Excludes Boss 429 engines.

New reproduction of Ford part number D0OZ-9S500-A, Hi Temperature choke gasket for all 1970-71 429 Cobra Jet engines. Must utilize the stock Ford cast iron 429 Cobra Jet intake manifold. Fits J and C code 1971 Mercury Cougar and Ford Mustang, and J and C code 1970-71 Ford Torino, Ford Ranchero, Mercury Cyclone.*Note - Excludes 429 Super Cobra Jet engines which used a different intake manifold.

Used cast iron choke stove from any 1970-73 351C-2V Ford engine. This is held on with 4 bolts, and to our knowledge no block off plate is reproduced. Casting number on the iron plate is D0AE-9A705-D, which is only for the plate. The plate and coiled tube assembly has a Ford part number of D0AZ-9C869-B. No hardware included.

Set of 12 bolts for the intake manifold on any factory 1970-74 Ford 351C-4V engine. AMK F-1321.*Note - Excludes 351C-2V and 351W engines.

Set of 12 bolts for the intake manifold on any factory 1970-74 Ford 351C-2V engine. AMK F-1313.*Note - Excludes 351C-4V and 351W engines.

New gaskets for installing your 429 Cobra Jet intake manifold. This is the Felpro branded gasket. Fits 1970-71 Ford 429CJ engines. 1971 Mercury Cougar and Ford Mustang with J or C code 429CJ engines. Intake to cylinder head gaskets and intake end pieces, along with O ring for distributor. *Note - Excludes N code 429-4V or Thunderjet, passenger car engines.

5/16-24 hex nut 7/16" head that is used to secure the carburetor to the intake manifold. If you need to replace your rusty old studs, we also carry an eight piece kit that contains the studs and nuts. Sold individually. AMK B-12786

Grade "B" 1971-72 passenger side tail light lens. Grade B lens will have 1 or 2 blemishes which may include a small crack, chip, discoloration, or other defect.  Replaces Ford part number D1WY-13450-A. *NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's and is the designer of all of our solid state sequential systems. There is no question he cannot answer! Here is a...