All Available Parts - 1971 Mercury Cougar

Passenger side inner convertible top rail extension, made of cast aluminum. One of the most fragile parts on the convertible top assembly. Prone to failure when one of the hydraulic cylinders fails and the top assembly is forced. Comes as shown, be sure to save all of your installation hardware and bushings. Casting number on part reads: D1ZB-76531A08-A.

Ground wire for convertible pump motor. Short wire section that attaches to the pump motor and grounds to the chassis of any 1969-73 Mercury Cougar or Ford Mustang. Easy to copy, #10 gauge wire about 11-1/2 inches long. Two ring terminals attached. Easy peasy.

Reproduction tips and screws for your convertible top welt. It's the strip that goes across the top back side of the convertible top. These are the decorative tips that go on each end of the welt.Each kit includes two tips and two screws.

No excuses 100% complete mechanism with no cracks, missing parts or heavy corrosion. We can include the top cylinders but will not guarantee they will not leak. We carefully break this down by removing the header and crossbows and placing the original bolts back in the holes. Once you get this from UPS it will be very evident how it goes back together.

This listing consists of 2 L shaped die cast side mouldings and one rear stainless moulding. We require clean cores for exchange prior to shipping. CORES MUST HAVE CLIPS AND STUDS IN PLACE. If you are in question as to whether your cores are acceptable or not, please send us several digital pictures. These differ from Mustang in that the Cougar has the center portion recessed with black semigloss paint. Our restored mouldings do not have the paint applied. The ford casting numbers as seen...

Used driver side (left hand) horizontal quarter window moulding / trim. They were used in conjunction with the door trim on XR7 models only. Located at the base of the quarter window and mounted horizontally on XR7 convertible models only. Due to the difficulty in obtaining trim we no longer sell these without first having you send us your cores.

Used passenger side (right hand) horizontal quarter window moulding / trim. They were used in conjunction with the door trim on XR7 models only. Located at the base of the quarter window and mounted horizontally on XR7 convertible models only. Due to the difficulty in obtaining trim we no longer sell these without first having you send us your cores.

Set of restored windshield pillar post mouldings / trim for the Mercury Cougar convertible. If your stainless parts have no real damage you may consider investing in a cheap standing buffer and polishing kit. When you purchase one of our restored stainless trim parts you are paying for the removal of dings and scrapes as well as the polishing of the part. Due to the difficulty in obtaining trim we no longer sell these without first having you send us your cores. ...

Used driver side (left hand) convertible top boot trim moulding / trim for the 1971-73 Mercury Cougar convertible. If it were not for the paint over-spray on the black stripe of the drivers side piece these would be ready to bolt on and go! This is the best used example we have ever had in stock. We have several sets in stock with moderate to heavy pitting that are reasonably priced. Ford casting number reads D1WB-76423A19-AA or D1WY-76423A19-A. *Note - This item is not correct for a Ford...

New to the Market! Correct convertible side tension cables for the 71 through 73 Cougar and Mustang.  Replaces Ford Part #: D1ZZ-652806-A.  

Driver side stainless steel weather strip retainer for 71-73 Cougar and Mustang convertibles. This retainer screws to the windshield pillar post and holds the weather stripping for the front of your door window glass. Plan on replacing the weatherstripping. There is also the companion lower aluminum retainer listed on our site.These used stainless pieces generally polish up very well with 0000 steel wool. The little black plastic coated clip will be compromised due  to age and...

Passenger side stainless steel weather strip retainer for 71-73 Cougar and Mustang convertibles. This retainer screws to the windshield pillar post and holds the weather stripping for the front of your door window glass. Plan on replacing the weatherstripping. There is also the companion lower aluminum retainer listed on our site. These used stainless pieces generally polish up very well with 0000 steel wool. The little black plastic coated clip will be compromised due to age and heat.Replaces...

Excellent quality reproduction sun visor assembly for the convertible 1971-73 Mercury Cougar and Ford Mustang. These feature the correct satin finish, fit perfect and look spot on. The original casting numbers as seen on the back side will read D1ZB-7604123-AE for the driver side and D1ZB-7604122-AE for the passenger side. Sold as a pair.Replaces Ford part numbers D1ZZ-7604144-A, D1ZZ-7604145-A, and D2ZZ-7604144-A, D2ZZ-7604145-A.

We have found a new manufacturer of the convertible top boots that are supposed to fit much better than the boots we were previously selling. See Pics Below. Ford calls this part the "folding top dust hood". Made from original pattern. Features long lasting vinyl. Includes foam pads. We stock the black and white. All other colors are ordered on demand from the manufacturer. Please note that convertible boots never came from the factory with snaps (except the 6 on the interior panels), so any...

We have found a new manufacturer of the convertible top boots that are supposed to fit much better than the boots we were previously selling. See Pics Below. Ford calls this part the "folding top dust hood". Made from original pattern. Features long lasting vinyl. Includes foam pads. We stock the black and white. All other colors are ordered on demand from the manufacturer. Please note that convertible boots never came from the factory with snaps (except the 6 on the interior panels), so any...

Restored show quality driver side (left hand) horizontal quarter window moulding / trim. They were used in conjunction with the door trim on XR7 models only. Located at the base of the quarter window and mounted horizontally on XR7 convertible models only. Due to the difficulty in obtaining trim we no longer sell these without first having you send us your cores. ...

Rear most convertible top bow #4, from a 1971-73 Mercury Cougar or Ford Mustang convertible top assembly. This is the last bow and would have had a tack strip attached.   Ford part number D1ZZ-7651278-A.

Used stainless steel convertible top trim for the middle section of the exterior boot trim. We only sell this item on an exchange basis only, you are required to pre-send your restorable cores to West Coast Classic Cougar. These mouldings work with any 1971-73 Standard or XR7 model Cougar. These trim pieces will have at least 3 of the mounting studs intact for mounting.  Due to the difficulty in obtaining trim we no longer sell these without first having you send us your cores. Keep...

Bolt for the under side convertible plate on any 1969-73 Mercury Cougar or Ford Mustang. 6 total bolts needed for attaching reinforcement plate to undercarriage. Sold individually. These are a close match to the original bolts, which are 3/8-16 x 1-1/2". Ford tightening specs. are 25-38 lbs. ft. torque.Replaces Ford number 57048-S2.

C5ZZ-7610962-A Ford description of this plate is "Plate - Front floor lower cross member". All 1969-73 Cougar convertibles and all 1965-73 Ford Mustang convertibles use this plate. Bolts into place with 6 hex bolts 3/8-16 x 1-1/8" with washers. These were painted satin black from the factory. Some time between 1969 and 1973 this plate underwent a revision by Ford. We are going to split by generation. 1969-70 plates are flat on one edge. 1971-73 has a slight hump or bend. Either works and...

Original used three piece tack strips for the 1969 - 1970 Cougar convertible. Over-sized, must be shipped via UPS.

Preproduction wiring harness, connects the convertible top switch to the pump on both the xr7 and standard model Cougars and Mustang 1969 - 1973 convertibles.

Grade B used convertible sun visor bracket assembly for the passenger side of any 1971-73 Mercury Cougar or Ford Mustang. Grade B will have some pitting in the pot metal. Sanding and painting will be required for the best results. Two casting numbers found between 1971 and 1973. We won't always have both numbers in stock but from the front side they are the same. Can be either D1ZB-7604122-AD or D2ZB-7604122-AA.  These will almost always show some wear, in the pocket where the hook...

Grade B used convertible sun visor bracket assembly for the driver side of any 1971-73 Mercury Cougar or Ford Mustang. Grade B will have some pitting in the pot metal. Sanding and painting will be required for the best results. Two casting numbers found between 1971 and 1973. We won't always have both numbers in stock but from the front side they are the same. Can be either D1ZB-7604123-AE or D2ZB-7604123-AA.  These will almost always, show some wear in the pocket, where the hook...

Driver side convertible rear top rail, made of cast aluminum. One of the most fragile parts on the convertible top assembly. Prone to failure when one of the hydraulic cylinders fails and the top assembly is forced. Comes as shown, be sure to save all of your installation hardware and bushings. Sometimes there may be a broken screw for the cable that will need to be drilled out.  Casting number on part reads: D1ZB-7653139-AB.

Passenger side rear convertible top rail, made of cast aluminum. One of the most fragile parts on the convertible top assembly. Prone to failure when one of the hydraulic cylinders fails and the top assembly is forced. Comes as shown, be sure to save all of your installation hardware and bushings. Very hard part to find unbroken, sometimes the screws break off for the cables. You may have to drill out a broken screw.  Casting number on part reads: D1ZB-7653138-AB.

Our grade "A" rear quarter panel extensions have no obvious dings, scrapes, bumper contact damage or warping due to over tightening of studs. Ford part # D1WB-6528518, Mercury MPC # D1WY-6528010-A. Do you have questions about your Cat's factory pinstriping? This link may help.

Our grade "A" rear quarter panel extensions have no obvious dings, scrapes, bumper contact damage or warping due to over tightening of studs. Ford part # D1WB-6528519, Mercury MPC # D1WY-6528011-A. Do you have questions about your Cat's factory pinstriping? This link may help.

Reproduction full length driver side floor pan. This pan is technically for 67 - 68, but will work for 67 - 73 Cougars and Mustangs. There were small differences such as drain holes / no drain holes etc. between the years, but will work for all years. Hi, and sincerely thanks for all help I've received from WCCC during my (mega) 1968 restoration project. If everyone would be that helpful, the world would be a much better place. ;-) My car is almost ready for the road, but - as always - there...

Reproduction full length passenger side floor pan. This pan is technically for 67 - 68, but will work for 67 - 73 Cougars and Mustangs. There were small differences such as drain holes / no drain holes etc. between the years, but will work for all years.

Complete floor pan for the 1969-70* Ford Mustang or 1969-70* Mercury Cougar. This item ships direct from the manufacturer for most orders. This item must ship via truck freight. Shipping to business addresses tends to be less than residential addresses, sometimes substantially.This item ships direct from the manufacturer for most orders and must be shipped via truck freight, and CANNOT ship via UPS. Shipping to business addresses tends to be less than residential addresses, sometimes...

* This is the closest available fit full floor pan for the 1969-73 Ford Mustang Convertible or Mercury Cougar Convertible, this pan will need modification to "make it fit." Complete floor pan for the 1969 - 72 Mercury Cougar or 1965-68* Ford Mustang Convertible. This item ships direct from the manufacturer for most orders and must be shipped via truck freight, and CANNOT ship via UPS. Shipping to business addresses tends to be less than residential addresses, sometimes substantially....

Driver side (left hand) front seat floor pan.  This pan is cut from the full floor pans in order to save on shipping costs when a customer does not need the entire length pan. Cutting from the Dynacorn full length pans means this will be a quality cut, when compared to other pans on the market. 1967-68 style ribbing, works in 1969-70 and can be modified to fit 1971-73. *NOTE* This floor pan has the outside lip bent down which is proper for coupes, convertibles were bent up. You can either...

These are exact replacements for 1964-68 Ford Mustang, but looks similar to the 1967-68 Mercury Cougar. This floor pan will also fit the 1969-73 Ford Mustang, but 1969-70 cars have different ribbing configurations. To use this pan in 1971-73 cars will require modification. This heavy gauged stamped steel floor pan starts behind the seat platform *NOTE* This floor pan has the outside lip bent down which is proper for coupes, convertibles were bent up. You can either bend it up or remove it and...

These are exact replacements for the 1964-68 Ford Mustang, but looks similar to the pans for the 1967-68 Mercury Cougar. These floor pans will also fit the 1969-73 Mustang, but the will requires modification to fit properly. 1969-70 cars have different ribbing configurations and 1971-73 cars can use these also. This is a heavy gauged stamped steel floor pan *NOTE* This floor pan has the outside lip bent up which is proper for coupes. Convertibles were bent down. You can either bend it up or...

Premium grade and quality reproduction floor pan plug. These screw right onto the floor pans prior to the carpet underlay and are much better quality than the originals. The original plugs have rough stampings and are made from galvanized steel. These premium plugs have a smooth cutout and are zinc plated. Fits: 1967 Mercury Cougar1968 Mercury Cougar 1969 Mercury Cougar 1970 Mercury Cougar 1971 Mercury Cougar 1972 Mercury Cougar 1973 Mercury Cougar 1967 Ford Mustang1968 Ford Mustang 1969 Ford...

This is our reproduction, uncut, driver side (left hand), long, front and rear floor pan for your Mercury Cougar convertible.

This is our reproduction, uncut, passenger side (right hand), long, front and rear floor pan for your Mercury Cougar convertible.

Welded in hooked retainer for the rear seat back installation on any 1967-73 Mercury Cougar or Ford Mustang coupe or hard top body style. This bracket welds to the edge of the package tray. Two hooks per car, sold individually. We cut out a individual sections as shown. Make good measurements prior to removal of your old brackets. You will need to drill out the spot welds prior to installation. For sure that basic Ford part number is 62118.

Used seat belt anchor plate that has been cut out from a car in our salvage yard. Must be welded to floor pan. 6 total per car, 2 inboard in the transmission tunnel, and 4 on the rear seat pans. The front outboard anchors are part of the rocker rails. Rectangular shaped like the 1967-73 cars. We have noticed that the last generation 1971-73 Cougars had 4 round shaped plates in the rear floors. Same threads, all work the same. These were pretty much used on all Ford cars starting in...

Used seat belt anchor plate that has been cut out from a car in our salvage yard. Must be welded to floor pan. 4 total per car, all 4 on the rear seat pans. The front outboard anchors are part of the rocker rails. Rectangular shaped for the front seat belts inboard on 1971-73 cars. Round anchor bracket with factory welded nut for added strength. See related items for good used seat belt anchor plates if you have concours needs. Replaces Ford Part # D1AZ-6561216-A. ...

Hook bracket weld in retainer for the rear seat installation on any 1971-73 Mercury Cougar. This is the front bracket that holds in the rear seat and was used on both coupes and convertibles. Sold individually, two required per car. We cut out a section of the floor under the rear seat as shown. Make good measurements prior to removal of your old brackets.  The Ford number is C9AZ-6263370-A.

Floor tunnel body reinforcing plate for the floor shifter on any 1971-73 Mercury Cougar or Ford Mustang. Used plate spot welded to the underside of the floor. Has threaded inserts installed. Contoured differently than previous years. We cut, you remove spot welds. Take your measurements for location, before removing your old floor and or tunnel.  Ford part number D1ZZ-6512118-A.

Mercury Cougar right front fender inner splash shield.Ford part # D1WY-16102-A.

Mercury Cougar left front fender inner splash shield.Ford part # D1WY-16103-A.

Mercury Cougar right rear fender inner splash shield.Ford part # D1WY-16102-B.

Mercury Cougar left rear fender inner splash shield.Ford part # D1WY-16103-B.

Ready to clean up and install, not bent, tight joints, minimal surface rust.

Ready to clean up and install, not bent, tight joints, minimal surface rust.

Grade "B" fenders will have minor rust in the lower portion behind the wheel or minor dents but it will not have both. Please call 503-463-1130 for details.Passenger side fender for all 1971-72 Mercury Cougars. B grade sheet metal will need a couple of hours of minor body work performed prior to paint. *Customer Feedback*"The parts are in great condition, just as described! 30 year old metal parts with virtually no rust (not like my parts found in Iowa). Good communication and worked with me...

Crating Fee Applies To This Item. You will be contacted once your order is reviewed to discuss the crating fee. Crating fees generally run between $175 - $250 (this does not include truck freight charges). If an item has a crating fee, this usually indicates that it must ship via Truck Freight and can only be shipped to US addresses and select Canadian addresses. Grade A hoods have no rust under the lip, nothing more than a light skim coat of filler found anywhere, no damage in the hinge areas...

Crating Fee Applies To This Item. You will be contacted once your order is reviewed to discuss the crating fee. Crating fees generally run between $175 - $250 (this does not include truck freight charges). If an item has a crating fee, this usually indicates that it must ship via Truck Freight and can only be shipped to US addresses and select Canadian addresses. Our grade B hoods are 100% rust free with minor damage to the top side. Hoods are shipped via www.forwardair.com so check their site...

Rust free with no prior damage. Cut with a plasma cutter well above the style line from a solid Western fender. Generally we cut these about 14" up but you can have it cut anywhere you wish and the price remains the same, only the shipping increases.

Grade "A" doors have never been dented in, cracked in the door latch area or rusted in the corners under the weatherstrip. When you turn it over and inspect it, the bottom seam it is not expanding from the inside out due to rust. There are no drilled holes for an after market impact strip and the sound deadener is usually still intact. Often times it will still bear the original paint but do expect multiple, small door dings. This is the best condition Western door you could ever hope to find,...

You may consider buying our grade "B" door over our grade "A" door if you are doing a high end restoration. Here is the reasoning; due to the design of the 71-73 door, silt is trapped in all of the door corners, these tight recesses always have silt collected in them and when you add moisture you get corrosion. Our grade "A" doors do not have noticeable blisters but since there is no paint or sound deadener in the depths of the corners we know there is some amount of corrosion taking place...

Reproduction driver side (left hand) front inner apron for Mercury Cougar and Ford Mustang.

Reproduction passenger side (right hand) front inner apron for Mercury Cougar and Ford Mustang.

Reproduction stamped steel driver side (left hand) rear inner apron for Mercury Cougar or Ford Mustang.

Reproduction passenger side (right hand) rear inner apron for Mercury Cougar and Ford Mustang.

Used passenger side (right hand) shock tower in excellent condition as cut from a Western parts car. No specific part number for this structural front suspension section. Generic Ford part # D1ZZ-16054-A, includes apron and side member.

Used driver side (left side) shock tower that is in excellent condition as cut from a Western parts car. For Mercury Cougar and Ford mustang with no specific part number for this structural front suspension section. Generic part # D1ZZ-16055-A, includes apron and side member.

1971-73 shock towers are not reproduced and finding rust free Western aprons is getting to be a challenge. This is a great value for those needing multiple parts and want factory spot welds. Generic Ford part # D1ZZ-16055-A, includes apron and side member.

1971-73 shock towers are not reproduced and finding rust free Western aprons is getting to be a challenge. This is a great value for those needing multiple parts and want factory spot welds. Generic Ford part # D1ZZ-16054-A, includes apron and side member.

Comes with good shock towers, front aprons, and core support. This is a great value for those that need to replace multiple parts upfront as you will not only get factory joined parts that will save you money and time, but it will also  preserve the value of your car. With a clean Western cut like this, one should be able to install it so that nobody would ever know your car has had anything replaced. You will have to call to order this one. Expect to pay about $300 for crating and...

Used passenger side (right hand) coil spring cover that is a good solid western part for Mercury Cougar and Ford Mustang. Ford part # D1ZZ-3382.

Solid, used, and undamaged passenger side (right hand) shock tower brace for Mercury Cougar and Ford Mustangs. Consider our brace kits for the best bang for your hard earned buck!Ford part # D1ZZ-16A052-A.

Solid, used, and undamaged driver side (left hand) shock tower brace for Mercury Cougar and Ford Mustangs. Consider our brace kits for the best bang for your hard earned buck! Ford part # D1ZZ-16A053-A.

Solid, used, and undamaged driver and passenger side shock tower braces for Mercury Cougar and most Ford Mustangs. We recommend going with a pair of these used braces, as compared to the reproductions we offer. Our Braces are going to be a better fit all around, and the quality is far better than the repros.Ford part #s D1ZZ-16A053-A driver side (left hand), D1ZZ-16A052-A passenger side (right hand). *Installation Tip* These brackets attach 'under' the cowl lip. ...

Used 1971-73 style bolt and nut for installing the shock tower brace to the cowl.

Reproduction passenger side (right hand) inner front frame patch for Mercury Cougar and Ford Mustang.

Reproduction driver side (left hand) outer front frame rail patch for Mercury Cougar and Ford Mustang. The outer rail has weld nuts installed for proper installation.

Reproduction driver side (left hand) inner front frame patch for Mercury Cougar and Ford Mustang.

You may consider buying our grade "B" door over our grade "A" door if you are doing a high end restoration. Here is the reasoning; due to the design of the 71-73 door, silt is trapped in all of the door corners, these tight recesses always have silt collected in them and when you add moisture you get corrosion. Our grade "A" doors do not have noticeable blisters but since there is no paint or sound deadener in the depths of the corners we know there is some amount of corrosion taking place...

Grade "B" fenders will have minor rust in the lower portion behind the wheel or minor dents but it will not have both. Please call 503-463-1130 for details. Driver side fender for all 1971-72 Mercury Cougars. B grade sheet metal will need a couple of hours of minor body work performed prior to paint. *Customer Feedback* "The parts are in great condition, just as described! 30 year old metal parts with virtually no rust (not like my parts found in Iowa). Good communication and worked with me to...

New pair of white and yellow paint sticks for the Mercury or Ford. These units were used by FORD at the assembly plants to mark fender aprons

This is a great, well fitting reproduction and is also all you need to replace the firewall on your 71 - 73 Cougar or Mustang. This is the entire wall, from passenger side to driver side, cowl to floor pan. Made specific for cars with A/C.

Used driver side grille assembly found in all 1971-73 Mercury Cougar and Ford Mustang quarter panels inside the door jamb. Grade A used condition, will have all rubber flaps intact, plastic in good condition. B grade used also available.Replaces Ford part number D0ZB-65280B62-A.*Trivia - This part was also used on 1970 Mercury Cougars and Ford Mustangs but they swapped sides. This part goes to the passenger side of 1970 Cougars and Mustangs. The Ford and Mercury Master Parts Catalogs are...

Rust free with no prior damage. Cut with a plasma cutter well above the style line from a solid Western fender. Generally we cut these about 14" up but you can have it cut anywhere you wish and the price remains the same, only the shipping increases.

Rust free with no prior damage. Cut with a plasma cutter well above the style line from a solid Western fender. Generally we cut these about 14" up but you can have it cut anywhere you wish and the price remains the same, only the shipping increases.

Used driver side grille assembly found in all 1971-73 Mercury Cougar and Ford Mustang quarter panels inside the door jamb. Grade B used condition, will have scratches and or rubber flaps torn / missing. A grade used also available.Replaces Ford part number D0ZB-65280B62-A.*Trivia - This part was also used on 1970 Mercury Cougars and Ford Mustangs but they swapped sides. This part goes to the passenger side of 1970 Cougars and Mustangs. The Ford and Mercury Master Parts Catalogs are wrong. ...

Used passenger side grille assembly found in all 1971-73 Mercury Cougar and Ford Mustang quarter panels inside the door jamb. Grade B used condition, will have scratches and or rubber flaps torn / missing. A grade used also available.Replaces Ford part number D0ZB-65280B63-A.*Trivia - This part was also used on 1970 Mercury Cougars and Ford Mustangs but they swapped sides. This part goes to the passenger side of 1970 Cougars and Mustangs. The Ford and Mercury Master Parts Catalogs are wrong. ...

Used passenger side grille assembly found in all 1971-73 Mercury Cougar and Ford Mustang quarter panels inside the door jamb. Grade A used condition, will have all rubber flaps intact, plastic in good condition. B grade used also available.Replaces Ford part number D0ZB-65280B63-A.*Trivia - This part was also used on 1970 Mercury Cougars and Ford Mustangs but they swapped sides. This part goes to the passenger side of 1970 Cougars and Mustangs. The Ford and Mercury Master Parts Catalogs are...

Used driver side upper front fender nose section. Rust free with no prior damage. Cut with a plasma cutter behind the leading edge of the wheel well. There are minor differences between the 71, 72 and 73 Fenders, but this fender nose section is the same for all three.

Used passenger side upper front fender nose section. Rust free with no prior damage. Cut with a plasma cutter behind the leading edge of the wheel well. There are minor differences between the 71, 72 and 73 Fenders, but this fender nose section is the same for all three. ...

Reproduction passenger side (right hand) outer shock tower cover for Mercury Cougar and Ford Mustang. We cannot stand behind this product as it is an ill fitting reproduction, however do offer rust free used originals. No returns accepted.

Reproduction driver side (left hand) outer shock tower cover for Mercury Cougar and Ford Mustang. We cannot stand behind this product as it is an ill fitting reproduction, however do offer rust free used originals. No returns accepted.

Used driver side (left hand) coil spring cover that is a good solid western part for Mercury Cougar and Ford Mustang.Ford part # D1ZZ-3383.

1971-72 Front unibody cut with cowl. This cowl has the holes for the factory air conditioning. 1973 frame rails are constructed differently for the energy absorbing front bumpers. Excellent value! Please consider a front clip replacement for your vintage 1967-73 Cougar or Mustang - including fastbacks! No differences exist between the front understructures of a Mercury Cougar or Ford Mustang year for year. How many hours of labor is needed to replace individual aprons, towers, radiator...

1971-72 Front unibody cut with cowl. This cowl has the holes for the factory air conditioning. 1973 frame rails are constructed differently for the energy absorbing front bumpers. Excellent value! Please consider a front clip replacement for your vintage 1967-73 Cougar or Mustang - including fastbacks! No differences exist between the front understructures of a Mercury Cougar or Ford Mustang year for year. How many hours of labor is needed to replace individual aprons, towers, radiator...

This cowl is made for a car without AC but all you have to do to modify for a factory AC car is plug the vent hole on the driver side. Replaces Ford part # D1ZZ-6502010-A.

Finally, a reproduction firewall for your Mercury Cougar or Ford Mustang convertible. Ford part # D1ZZ-6501610-A.

Pair of reproduction shock tower braces that connect the shock towers to the firewall. Sold in a pair. Not even close to being as good as our used original FoMoCo units. Replaces Ford part # D1ZZ-16A052-A & D1ZZ-16A053-A.

The Cougar used a seat riser that was about one inch lower in height compared to the Mustang so as to compensate for the more plush foam and upholstery.

The Cougar used a seat riser that was about one inch lower in height compared to the Mustang so as to compensate for the more plush foam and upholstery.

Reproduction passenger side inner A pillar / kick panel for the 1971 - 1973 Cougar or Mustang.

Reproduction driver side inner A pillar / kick panel for the 1971 - 1973 Cougar or Mustang.

Very hard to find with no damage but we have a few! No rust other than surface, no obvious filler and no dents. Grade "A" Western sheet metal is always going to be your best bet when you can find it. This unit is also known as a bumper filler, rock guard, or filler panel.Ford part # D1WY-17779-A.

This solid, grade "B" part will not have damage in the hard to fix contoured areas. This is a good value for the money, we will not send you junk. This unit is also known as a bumper filler, rock guard, or filler panel.Ford part # D1WY-17779-A.

This is how most of our taillight panels are cut off. If you only need a partial panel we can do that too, just give us a ring. Keep in mind we only cut panels like this if both 1/4's are ruined. It is getting very hard to come up with some of these cuts.Click on images to enlarge. ...

10 of these are used to mount the 1968-71 Cougar hood scoop found on the 68 428 CJ, 1969-70 Eliminator, 1969-70 428 Ram Air equipped Cougars, and 1971 GT and 429CJ. Sold individually Zinc (dark silver).