All Available Parts - 1970 Ford Mustang

This arm is attached to your automatic transmission floor shifter (see picture at left). Fits all 1969-70 Mercury Cougar and Ford Mustang. Ford calls technical name for this part is 'Arm, Support'. These used parts will come with an intact bushing and nut. Correct for FMX and C-6 transmissions. Ford part number C9ZZ-7302-A. This part may have the course threads or fine threads. Normally this item ships with the course threads. We also stock the 1971-73 version that has a captured stud for...

Ford called this part a 'sleeve'. Attaches to the lower shifter arm with a hitch pin. Has nice bushing, with correct nut, washer, and pin. The 1967/68 and 1969/73 versions are identical. The C1AA-7353-C sleeve has fine threads, the C9OZ-7353-A has course threads. Fits all 1967-73 Mercury Cougar and Ford Mustang, and we suspect many other Ford vehicles beginning in 1961. Check out our video on rebuilding your shifter below: ...

Complete chrome automatic shifter lever assembly for any 1969-73 Mercury Cougar or Ford Mustang with or without consoles. This is the early version with small width pawl. Good used part no heavy pitting on the chrome, we sell these levers with installed cable, pawl, spring, and gear release assembly. Ford part number for the lever is C9ZZ-7210-A. *Note - Chromed lever and internals only, no T handle. Check out our video on rebuilding your shifter below: ...

Complete chrome automatic shifter lever assembly for any 1969-73 Mercury Cougar or Ford Mustang with or without consoles. This is the late version with wider width pawl. Good used part no heavy pitting on the chrome, we sell these levers with installed cable, pawl, spring, and gear release assembly. Ford part number for the lever is C9ZZ-7210-C. *Note - Chromed lever internals only, no T handle. Check out our video on rebuilding your shifter below: ...

Allen head set screw for all stock Ford automatic shifter handles on any 1967-73 Mercury Cougar or Ford including Mustang. Uses the same 3/32 inch allen wrench for attaching as the originals. Most handles take two of these set screws, one on the dummy button, and one to attach to the top of the shifter lever. The 1973 all chrome shift handle only uses one of these set screws. Original Ford part number 374985-S. Check out our video on rebuilding your shifter below: ...

Reproduction of the little plastic shift indicator arrow, that is illuminated by the little bulb in your shifter housing. Fits 1969-73 Mercury Cougar and Ford Mustang. Also fits 1971 and newer Pinto, Bobcat, Maverick and Comet with floor shift automatic transmissions. Ford part number C9ZZ-7A110-A. Check out our video on rebuilding your shifter below: ...

Replacement rubber bushing for repairing any automatic shift arms on any 1967-73 Mercury Cougar or Ford Mustang, and most Fords with automatic floor shift levers. Fits arms with 3/4 inch lower holes for attaching transmission shift rods. Replaces Ford part number C7ZZ-7343 Check out our video on rebuilding your shifter below: ...

Restored chrome automatic shifter lever for any 1969 and most 1970 Mercury Cougar or Ford Mustang with or without consoles. Sometime in the 1970 era, Ford switched to a larger pawl. Easy to identify if you look at the slit on the lever. We sell these bare for those car owners that have pitted shifter levers. Ford part number C9ZZ-7210-A. *Note - Chromed lever only, sold without cable, pawl, handle, etc. Check out our video on rebuilding your shifter below: ...

Restored chrome automatic shifter lever for some 1970 Mercury Cougar or Ford Mustang, and all 1971-73 Cougar and Mustangs, with or without consoles. Sometime in the 1970 era, Ford switched to a larger pawl. Easy to identify if you look at the slit on the lever. We sell these bare for those car owners that have pitted shifter levers. Ford part number C9ZZ-7210-C. *Note - Chromed lever only, sold without cable, pawl, handle, etc. Check out our video on rebuilding your shifter below: ...

Restored shifter T handle as found starting in 1968 and through, 1972 Mercury Cougar and Ford Mustang with automatic transmissions. This handle will actually fit on most Ford automatic floor shift levers of the era. Design is a little thicker in the body, compared to earlier designs. Core charge applies. Replaces Ford part number C8OZ-7213-A. Check out our video on rebuilding your shifter below: ...

Exact reproduction for the 1969 - 1973. Perfect fit and finish. You may want to replace yours with this inexpensive unit just for the fresh new luster alone. Your plastic end buttons may have faded to gray but they were originally black like this one. Replaces Ford Part #: C8OZ-7213-A, C90Z-7213-B, D3OZ-7213-A. Check out our video on rebuilding your shifter below: ...

Bare automatic shifter bucket or housing for use with the large pawl (0.160") shifter levers. Fits most 1970 Mercury Cougar and Ford Mustangs with or without console. Check the thickness of the pawl on your shifter lever. There are two different sizes and need to be matched for optimum fit. Early pawls were 0.100" thick, sometime in early 1970 through 1973 the pawls were made larger at 0.159". We recommend purchasing new bushings prior to installation. Replaces Ford part number C9ZZ-7A306-?...

This arm is attached to your automatic transmission floor shifter. Fits all 1969-73 Mercury Cougar and Ford Mustang. Ford calls technical name for this part is 'Arm, Support'. This used part will come with a captured lower stud for attaching the shift rod as shown. Correct for FMX and C-6 transmissions. This version is found on 1972-73 cars, it has the captured lower stud for mounting the automatic shift rod to the transmission. Ford part number D1ZZ-7302-A. Check out our video on rebuilding...

This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit of 50% of our web price for parts delivered in hand or by carrier to our Brooks, Oregon location. If you're not interested in store credit, just shoot us an email and we will let you know if it's is something we can pay cash for. We do not send cash for parts in advance but we often can compensate you within hours of receiving the...

Black plastic selector button for all 1968-72 Mercury Cougar and Ford Mustang with automatic transmission. This is for all cars with body type 65A, 65C, 63A, or 76A. This is for the base model shifter handle. Deluxe shifters were larger and had faux leather wrapping. Additionally it does not fit with the 1973 chromed T-handle without trimming.  Ford part C8ZZ-7C488-B.  Check out our video on rebuilding your shifter below: ...

1968-72 (works on 1967) Mercury Cougar XR7 and Ford Mustang Deluxe shifter button for automatic transmissions. This is for all cars with body type 65B, 76B, and Grande. This is for the deluxe model shifter. These are used, and because of the low grade of chrome plating, these will show some form of light pitting.  handle, which is larger and has a faux leather covered handle in a variety of colors. Ford part number C8OZ-7C488-A. Check out our video on rebuilding your shifter below: ...

Not a very good color match for Cougar owners, but will work well with blue interiors.Stunning quality and far less likely to crack than the originals. The 67 version was actually a little different than 68 - 73 but you would have to look close to see the difference. Check out our video on rebuilding your shifter below: ...

Reproduction console shift assembly for the 69 - 73 Cougar or Mustang. Included in this kit are the T-shifter assy, lever assy, housing and the shifter arm, seals and hardware. Replaces Ford part numbers: C7ZZ-7210C C7ZZ-7A306A C7ZZ-7302A C7ZZ-7213M Check out our video on rebuilding your shifter below: ...

Locking nut that attaches the shift lever to the shifter arm and support inside the shifter buckets. We normally see the fine threaded nuts on the 1967-70 shifters. Please check your shift arm support for correct threads.  3/8-24 threaded nut, serrated washer head style. Check out our video on rebuilding your shifter below: ...

Factory engine block spacer plate for 1969 1970 351W and 351C engines FMX (code X) and C6 (code U) transmissions. According to the Master Parts Catalog, it also fits 164 tooth bellhousings on 1968-70 with 302 engines too. We also stock the early version from 1968 and 157 tooth versions. There are probably two versions of this plate, we believe the the 1969 version did not have the indentations. Replaces Ford part number D0AZ-7007-A.

Reproduction engine block spacer plate for 69 - 73 Cougars or Mustangs with 351 engines and 3 or 4 speed manual transmissions. According to the Master Parts Catalog, it also fits 164 tooth bellhousings on 1968-70 with 302 engines too. We also stock the early version from 1968 and 157 tooth versions.

Reproduction engine block spacer plate for 1969 1970 351 engines FMX (code X) transmissions. According to the Master Parts Catalog, it also fits 164 tooth bellhousings on 1968-70 with 302 engines too.  Replaces Ford part number D0AZ-7007-A.

Unlike previous reproductions this has the correct grommet that passes through the firewall.  Replaces Ford Part #: C9ZZ-17260-A.  This cable measures 58 1/2" at its very most outer ends.

Made out of Nylon. Please confirm teeth count and direction of teeth. Color codes do not guarantee direct replacement. 4 speed Toploaders have reversed tooth direction. Click here to use our Speedometer Gear Calculator. Available in 16, 17, 18, 19, 20, 21, and 23 tooth*. Replaces Ford Part: C0DZ-17271-A, C0DZ-17271-B, C0DZ-17271-C, C0DZ-17271-D, C0DD-17271-A, C1DZ-17271-A * - 23 tooth gears are not a Ford part and only have a life expectancy of 25,000 miles. They also have been reported to...

Made out of Nylon. Please confirm teeth count and direction of teeth. Color codes do not guarantee direct replacement. 4 speed Toploaders have reversed tooth direction. Click here to use our Speedometer Gear Calculator. Available in 16, 17, 18, 19, 20, 21, and 23 tooth*. Replaces Ford Part: C0DZ-17271-A, C0DZ-17271-B, C0DZ-17271-C, C0DZ-17271-D, C0DD-17271-A, C1DZ-17271-A * - 23 tooth gears are not a Ford part and only have a life expectancy of 25,000 miles. They also have been reported to...

Made out of Nylon. Please confirm teeth count and direction of teeth. Color codes do not guarantee direct replacement. 4 speed Toploaders have reversed tooth direction. Click here to use our Speedometer Gear Calculator. Available in 16, 17, 18, 19, 20, 21, and 23 tooth*. Replaces Ford Part: C0DZ-17271-A, C0DZ-17271-B, C0DZ-17271-C, C0DZ-17271-D, C0DD-17271-A, C1DZ-17271-A * - 23 tooth gears are not a Ford part and only have a life expectancy of 25,000 miles. They also have been reported to...

Made out of Nylon. Please confirm teeth count and direction of teeth. Color codes do not guarantee direct replacement. 4 speed Toploaders have reversed tooth direction. Click here to use our Speedometer Gear Calculator. Available in 16, 17, 18, 19, 20, 21, and 23 tooth*. Replaces Ford Part: C0DZ-17271-A, C0DZ-17271-B, C0DZ-17271-C, C0DZ-17271-D, C0DD-17271-A, C1DZ-17271-A * - 23 tooth gears are not a Ford part and only have a life expectancy of 25,000 miles. They also have been reported to...

Made out of Nylon. Please confirm teeth count and direction of teeth. Color codes do not guarantee direct replacement. 4 speed Toploaders have reversed tooth direction. Click here to use our Speedometer Gear Calculator. Available in 16, 17, 18, 19, 20, 21, and 23 tooth*. Replaces Ford Part: C0DZ-17271-A, C0DZ-17271-B, C0DZ-17271-C, C0DZ-17271-D, C0DD-17271-A, C1DZ-17271-A * - 23 tooth gears are not a Ford part and only have a life expectancy of 25,000 miles. They also have been reported to...

Made out of Nylon. Please confirm teeth count and direction of teeth. Color codes do not guarantee direct replacement. 4 speed Toploaders have reversed tooth direction. Click here to use our Speedometer Gear Calculator. Available in 16, 17, 18, 19, 20, 21, and 23 tooth*. Replaces Ford Part: C0DZ-17271-A, C0DZ-17271-B, C0DZ-17271-C, C0DZ-17271-D, C0DD-17271-A, C1DZ-17271-A * - 23 tooth gears are not a Ford part and only have a life expectancy of 25,000 miles. They also have been reported to...

Speedometer cable that fits all 1969-73 Mercury Cougar and Ford Mustang with C-6 transmissions. This replacement cable is longer than the originals and does not have the firewall grommet. This cable measures 80" inches in length. Does not include speedometer gear, has correct style plastic clip that attaches to the back of the speedometer. Replaces Ford part # C9ZZ-17260-B, D0ZZ-17260-D, and D1ZZ-17260-G.

Used clip with bolt for attaching the speedometer cable to the transmission of the Mercury Cougar or Ford Mustang. This unit holds the gear end into both automatic and manual transmissions. Automatic codes W - C4, X - FMX, U - C6, 1 - 3 speed manual, 5 or 6 - 4 speed manual.

This screw attaches the speedometer / odometer to the instrument cluster housing. Two needed per speedometer, fits all years of Cougar 1967-73. This is an 8-32 x 3/8" hex flange head machine screw with captured washer. Sold individually. 

Reproduction transmission cooling lines made of OE steel for the Mercury Cougar or Ford Mustang equipped with the 351W and FMX transmission. These are sold in pairs

Reproduction transmission cooling lines made of OE steel for the Mercury Cougar or Ford Mustang equipped with the FMX automatic transmission and 351C engine. These lines are sold in pairs.

Reproduction transmission cooling lines for the Mercury Cougar or Ford Mustang equipped with the C-6 automatic transmission and 428CJ engine. These are sold in pairs.

Reproduction transmission cooling lines made of OE steel for the Mercury Cougar or Ford Mustang equipped with the C-6 automatic transmission and 428 Cobra Jet engine. These lines are sold in pairs.

Stainless Steel Transmission Modulator Line for the 1967, 1968, 1969 and 1970 Mercury Cougar or Ford Mustang with the C6 transmission.

Used transmission line adapter and check valve for all FMX transmissions. This fitting goes into the rear part of the transmission case and connects the rear most cooling line to the case. Has internal ball check valve to prevent fluid from back flowing. All FMX transmissions 1969-73 Mercury Cougar or Ford Mustang. The male threads going into the transmission case are 1/2-20 pipe threads.Replaces Ford part number C3AZ-7D174-A.

Rod used for locking the FMX transmission in "Park". Connects to the lower tab of the steering column and the FMX transmission shift arm. Prevents the transmission from shifting out of park when the ignition key is removed. Rod is about 14 inches long. The FMX, automatic transmission, was used on all 1970 Cougars with any 351 engine. Transmission code "X" on your door data tag. Replaces Ford part number D0ZZ-7E330-E. Casting number D0ZA-7E330-R.

Reproduction automatic shifter lever in chrome for the Mercury Cougar or Ford Mustang. Comes with inside cable parts. See the related items for more of your shifter needs. Check out our video on rebuilding your shifter below: ...

Formed metal clip that holds the gear end into any transmission. Automatic codes W - C4, X - FMX, U - C6, 1 - 3 speed manual, 5 or 6 - 4 speed manual.

Replacement transmission pan filter and pan gasket kit. For the C-6 (U Code) transmission. Replaces Ford Part Number: C7ZZ-7A098

Original dipstick or in Ford speak "Indicator - Oil Level" for FMX automatic transmissions. Application for 1969 - 1972 Mercury Cougar and Ford Mustang with 351 and FMX automatic transmissions, code "X" on your door data plate. Sometime during 1972 Ford changed to C9AP-7A020-C. Same dip stick, but with a longer handle.Ford master part number C9OZ-7A020-A, Ford casting # C9OP-7A020-A.

Replacement transmission pan filter and pan gasket kit. For the FMX (X Code) transmission. Replaces Ford Part Number: C9ZZ-7A098

Original dipstick or in Ford speak "Indicator - Oil Level" for C4 automatic transmissions. Application for 1967-68 Mercury Cougar 1966-70 Ford Mustang with 289/302 engines and C4 automatic transmissions, code "W" on your door data plate.Ford part # C6OZ-7A020-B.

New manufactured transmission oil pan for the Ford C6 transmission as found on 1967-73 Cougar and Mustangs, big block and small block engines. Very high quality heavy gauge steel.Replaces Ford part number C6AZ-7A194-A.

Reproduction transmission dipstick tube for 67 - 70 Cougars or Mustangs equipped with the C4 automatic transmission.Replaces Ford Part number C6AZ-7A020-B

New manufactured transmission yoke for a T-5 5 speed transmission.

New manufactured transmission slip yoke for either C-4 automatic transmission or small block manual 3 or 4 speed manual transmissions. Ford 1965-1973. 28 splines and 1-1/16" U-joint caps.

1967-70 Cougars with any FE engine (390-2V, 390-4V, 427 GT-E, 428CJ, or 428SCJ) and with C6 automatic transmission or manual transmissions.  Ford part #: C3AZ-7007-D.

Ford small block engines and with a 3 or 4 speed manual transmission. Fits only the larger 164 tooth flywheel.

Manual transmissions, include both 3 and 4 speed Top Loader transmissions. Ford part number C5TA-6394-A. For use with any 351 Windsor or 351 Cleveland engine for the years 1969 and 1970. Cast iron construction, for use with 164 tooth flywheels. Shipped bare, no hardware or clutch fork. Search words: 69 70 H M code engine Eliminator XR7 Sport Special

Reproduction bolts and washers for the manual transmission bell housing on any 1969 - 73 Cougar or Mustang equipped with a 302 / 351 engines and either 3 or 4 speed manual stick shift transmissions. Bell housing to engine block bolts. Fits most all other Ford small block V-8's from 1969-73.

Stainless Clutch Pedal Pad Trim. Replaces Ford Part #: C9ZZ-7B544-A.

Includes machined pedal shaft, washer and special pin. Replaces Ford Part #: C5ZZ-2478-AK.

This great little kit replaces stock Ford bushings that can wear out in as quick as one year. This is a very simple repair and upgrade, once you have removed the pedal support from the car. Upon completion of this you will be rewarded with greatly reduced pedal pressure and the knowledge that you will never have to replace these bushings again. This is a must have for anyone with a manual transmission.Does not fit 1971-73 Mercury Cougar or Ford Mustang.

This kit has everything you need to repair your clutch and brake pedal and pedal support in one easy kit.Repairs 1967-70 Mercury Cougar or 1965-70 Ford Mustang. *Hint - All 1967-70 brake pedal hangers have the clutch pedal shaft bushings, even the automatic cars. The originals are swedged in. * Does not fit 1971-73 Mercury Cougar or Ford Mustang.

This reproduction clip secures the clutch pedal rod end as it comes through the clutch pedal hanger.  Keep in mind that this reproduction is a different size compared to the original (see comparison above) and will need to be modified to make fit. As always, we recommend going with original used parts. You can find it here. Replaces Ford part number C8AZ-2B277-A ...

This kit has everything you need to repair your clutch and brake pedal and pedal support in one easy kit. Repairs 1967-73 Mercury Cougar or 1965-73 Ford Mustang. Plus many other Ford cars.This kit requires welding. For use on pedal hangers that are all wallered out, or 1971-73 pedal hangers that are not round. Kit has roller bearings. Quality Scott Drake / Holley product. *Hint - All 1967-70 brake pedal hangers have the clutch pedal shaft bushings, even the automatic cars. The originals are...

These four speed gears have the teeth reversed from the direction of the automatic gears. Made from Nylon. These gears only fit the 4 speed Toploaders. Click here to use our Speedometer Gear Calculator.   Replaces Ford Part # : C2DZ-17271-C 20 Tooth Gear Pictured

These four speed gears have the teeth reversed from the direction of the automatic gears. Made from Nylon. These gears only fit the 4 speed Toploaders. Click here to use our Speedometer Gear Calculator.   Replaces Ford Part # : C2DZ-17271-G 20 Tooth Gear Pictured

These four speed gears have the teeth reversed from the direction of the automatic gears. Made from Nylon. These gears only fit the 4 speed Toploaders. Click here to use our Speedometer Gear Calculator.   Replaces Ford Part # : C2DZ-17271-A 20 Tooth Gear Pictured

These four speed gears have the teeth reversed from the direction of the automatic gears. Made from Nylon. These gears only fit the 4 speed Toploaders. Click here to use our Speedometer Gear Calculator.   Replaces Ford Part # : C2DZ-17271-B 20 Tooth Gear Pictured

These four speed gears have the teeth reversed from the direction of the automatic gears. Made from Nylon. These gears only fit the 4 speed Toploaders. Click here to use our Speedometer Gear Calculator.   Replaces Ford Part # : C2DZ-17271-D 20 Tooth Gear Pictured

New internal speedometer gear fits 4 speed toploader transmissions. The largest number of 4 speed toploaders came stock with this gear. Replaces Ford Part #: C4DZ-17285-A.

New internal speedometer gear fits 4 speed toploader transmissions. Replaces Ford Part #: C5ZZ-17285-A.

Very good quality replacement speedometer cables. 76 inches Replaces Ford Part # : C9ZZ-17260-B

Grade B used inspection plate cover for all 390-4V and 428CJ engines with a manual transmissions, both 3 and 4 speeds. All years 1967 - 1970. Access cover to the flywheel and clutch. This cover will have some rust and a dent or creases. Find the Grade A cover here.

Reproduction inspection plate cover for all 390-4V and 428CJ engines with a manual transmissions, both 3 and 4 speeds. All years 1967 - 1970. Access cover to the flywheel and clutch.Replaces Ford part number C3AZ-6366-A.

Quality reproduction clutch pedal that works on all 1969-70 Mercury Cougar and Ford Mustangs. Improved design for easier installation.

D1TZ-7600-A New Old Stock service replacement clutch pilot bushing for all 1965-71 390/428/429 engines with manual transmissions. Will fit 1967-71 Mercury Cougar and Ford Mustang with 390-4V, 428CJ, 428SCJ, and 429CJ engines with 4 speed manual transmissions. Fits Fairlane, Cyclone, Torino, Ranchero also.

Nice reproduction clip for attaching the speedometer cable onto 3 and 4 speed 1967-70 Mercury Cougar and Ford Mustangs. Mounts to the firewall.

These four speed gears have the teeth reversed from the direction of the automatic gears. Made from Nylon. These gears only fit the 4 speed Toploaders. Click here to use our Speedometer Gear Calculator.   Replaces Ford Part # : C2DZ-17271-G 20 Tooth Gear Pictured

Speedometer cable with reducer for your 69 - 70 Cougar or Mustang with the C6 transmission.

Clutch Fork Pivot for Cougars manufactured after 2/16/1968. Replaces Ford Part #: C8AZ-7522-A.

D0DZ-7515-B Manual transmission clutch fork - 3 and 4 speed, stick shift transmissions. Alternate number D0DA-7515-B. Service replacement after 1973 D3DZ-7515-A for Maverick/Comet. Cougar 1970, 351 Engines. Mustang 1970, 250/302/351 Engines. Maverick 1971 - 1972, 250/302 Engines. Grabber Comet 1971 - 1972, 250/302 Engines. GT Fairlane 1970, 250/302/351 Engines. Torino / Ranchero 1970, 250/302/351 Engines. Montego / Cyclone 1970, 250/302/351 Engines. MX, ...

D0OZ-7515-A Manual transmission clutch fork - 4 speed, stick shift transmissions. Fork measures 12 inches long. Alternate number D0OA-7541-A. Designed for the big spline 1 3/8" input shaft toploaders. Cougar 1970, 428 Cobra Jet engines. Mustang 1970, 428 Cobra Jet engines. Torino / Ranchero 1970 - 1971, 429/429CJ Engines. Cobra Montego / Cyclone 1970 - 1971, 429/429CJ Engines.

D0ZA-7E046-D Reproduction adapter plate for mounting the Hurst 4 speed shifter control assembly to the Top Loader transmission. 1970 Mercury Cougar and Ford Mustang big block 428 Cobra Jet 4 speed only. Ford master part number D0ZZ-7E046-A. Link to the expert on Ford shifter linkages. Check out our video on rebuilding your shifter below: ...

Very nice reproduction of the D0ZZ-15525-A 1970 Mercury Cougar and Ford Mustang 4 speed backup light wiring harness, with the factory installed Hurst shifters. Plugs into the backup lamp switch and connects to the harness plug on the firewall behind the engine.

Backup light switch retainer for Hurst shifters as installed on 1970-73 Mercury Cougar, Ford Mustang, and most vintage Ford cars with factory installed Hurst shifters.

Backup light switch for factory installed Hurst competition shifters from 1970-73. This is a Daniel Carpenter reproduction, these are still being made by Hurst in small quantities (see our premium version). It does not include the bracket for holding the switch.Listed in the Motorcraft catalog as SW-943Also fits:CometFairlaneMontegoTorino Check out our video on rebuilding your shifter below: ...

Rod used for locking the 3 speed manual transmission in "Reverse". Connects to the lower tab of the steering column and the reverse control transmission lever shift arm. Prevents the transmission from shifting out of reverse when the ignition key is removed. Rod is about 13-1/2 inches long. The 3 speed manual transmission, could be ordered on any 1970 Cougar with any 351 engine. Transmission code "1" on your door data tag. Ford part number D0ZZ-7E330-B.

Fits 3 speed or 4 speed manual floor shifts. Sold individually. Check out our video on rebuilding your shifter below:

Get a grip with this reproduction Hurst T handle, or shifter handle, for the Mercury Cougar or Ford Mustang equipped with a manual transmission. Threads are 3/8-16. Check out our video on rebuilding your shifter below: ...

Very hard to find 69 - 70 Shelby / 67 - 69 Cougar 4 speed shifter knob. Almost a year in development was spent to get as close as possible to original N.O.S. sample. These very rarely come up for sale used and when they do, they are expensive. Knob insert is made of metal just like original not brass. Knob also has the correct groove in middle of body like 69 version and not the earlier version which does not. Not technically correct for a 67-8 Cougar, as the 67-8 does not have the groove in...

You will not need to make any modifications to run this leather unit in place of your original rubber boot used on three and four speed manual transmissions.

For use without consoles. This chromed square window slips over the stock or original style shifter boot on all 1969 and 1970 Mercury Cougar or Ford Mustangs with 3 or 4 speed manual transmissions. Includes 1970 Hurst.Replaces Ford part # C9ZZ-7262-C / Casting # C9ZB-7262-B

Chrome center cap with Red background and chrome Ford logo. Better than original! Original look wheel emblem is made from original dies. This plastic cap is painted and detailed in the original colors. This was never used on any year of Cougar but they do look good!  When using center caps on Legendary wheels, you will need these adapter plates. *Note - Certain late model disc brake rotors and aftermarket rotors have a slight clearance issue with the dust cap and these center...

Reproduction spinner cap for the Magnum 500 Legendary series wheel. Also works with the Magstar II wheel. Each spinner is die-cast with precision and finished in a show quality chrome plating. The exclusive anti-theft retainer plate keeps them in place and secure. A stamped aluminum Magnum 500 emblem and a "Bullseye" emblem are included so owners can choose which one to personalize their car with.Sold individually ...

This plastic center cap comes with each Legendary Wheel we sell at no cost. We list them for those that may lose or break one. The overall width is 2 1/2" and they are designed for a opening that is 2 3/8 " wide. Sold individually.Check out our video on Legendary Wheels below: ...

Reproduction set of 4 short valve stem assemblies for the Mercury Cougar or Ford Mustang. These new stems will look great on your Magnum, Styled Steel, Shelby, Eliminator or even stamped steel wheel.

Reproduction 15x7" Eliminator wheel with a black center and chrome rim for the Mercury Cougar or Ford Mustang / Torino. The only version of this wheel Mercury ever used on a factory order for a Mercury Cougar was a painted 14x6 with a trim ring used on the 1969 Eliminator. This black 15x7 is a really great custom made wheel that adds flash without deviating too far from the original look. As always, the cap is sold separate. Click here for the hubcap we recommend for this wheel. If you need a...

Reproduction 15x7" Eliminator wheel with a charcoal center and chrome rim for the Mercury Cougar or Ford Mustang / Torino. The only version of this wheel Mercury ever used on a factory order for a Mercury Cougar was a painted 14x6 with a trim ring used on the 1969 Eliminator. This charcoal 15x7 is a really great custom made wheel that adds flash without deviating too far from the original look. As always, the cap is sold separate. Click here for the hubcap we recommend for this wheel. If you...

Reproduction 15x7" Eliminator wheel with a silver center and chrome rim for the Mercury Cougar or Ford Mustang / Torino. The only version of this wheel Mercury ever used on a factory order for a Mercury Cougar was a painted 14x6 with a trim ring used on the 1969 Eliminator. This silver 15x7 is a really great custom made wheel that adds flash without deviating too far from the original look. As always, the cap is sold separate. Click here for the hubcap we recommend for this wheel. If you need...

Unfortunately we are not presently offering this wheel as the supplier has been consistently sending us inferior product and poor customer service at an ever increasing price. Please consider our Legendary wheel line, here is a video that shows more: ...

These off-shore Magnum wheels are supplied to us by Scott Drake. We no longer carry the US made version as the quality was VERY inconsistent. This wheel has a 4 1/4" backspace. We now have Magnum 500 caps that feature the Mercury Logo and the walking cat caps as well. Center caps and lugs are sold separate.   NOTE! These wheels are intended to be balanced with a lugcentric adapter. They will not balance with a traditional cone spacer on the tire spin balancer. Many tire shops do not deal...

These off-shore Magnum wheels are supplied to us by Scott Drake. We no longer carry the US made version as the quality was VERY inconsistent. This wheel has a 4 1/4" backspace. We now have Magnum 500 caps that feature the Mercury Logo and the walking cat caps as well. Center caps and lugs are sold separate.  These are best suited for 1971-73 Cougars. To run a tire larger than a 225/60/15 you may have to modify your fenders and quarters.  NOTE! These wheels are intended to be...

New aluminum 15x8" Magnum 500 wheel for your Mercury Cougar or Ford Mustang. A great way to reduce the un-sprung weight on your Cat or Pony and look great while doing it! This item also includes a center cap, but they are a cheap plastic chromed cap with a blacked out center. We recommend using the adapter plates and Magnum 500 center caps we sell from Scott Drake. Lug nuts sold separately, get them here. ...

New aluminum 17x7" Magnum 500 wheel for your Mercury Cougar or Ford Mustang. A great way to reduce the un-sprung weight on your Cat or Pony and look great while doing it!  This item also includes a center cap, but they are a cheap plastic chromed cap with a blacked out center.  We recommend using the adapter plates and Magnum 500 center caps we sell from Scott Drake. Lug nuts sold separately, get them here. ...

New Legendary Series 15x7" Glossy Finish Magnum 500 wheel for your Mercury Cougar or Ford Mustang. While they look almost identical to the original chromed steel version, these are actually a lighter, better-balanced aluminum alloy with a protective coating. These wheels come with free chromed plastic center caps. The caps have a red Legendary logo but we can include at no cost, a set of black and chrome walking cat decals (click here). Just add it to your cart if you'd like these decals. If...