Home > 1970 Mercury Cougar
All Available Parts - 1970 Mercury Cougar
Products (Click sub-categories above to ONLY display results for that Sub-Category) 501-600 of 5051
Sorted By:
Availability:
Display Options:
Availability: In-Stock Item
Item #: 19970 -
Ignition lock set is new original from the O.E.M. source. Factory fresh with two keys. Fits 1970 through 1973's manufactured before 5/17/1973. Replaces Ford Part #: D0AZ-11572-A, D2AZ-11582-B, SW-1114.
Availability: In-Stock Item
Item #: 14225 -
Steel door latch reinforcement repair kit. Countersunk bushings and screws for reinforcing the inside the door mounted latches on 1967-70 Mercury Cougar and Ford Mustangs. Kit has 6 machine screws and bushings, enough for both doors. The metal on the doors is very prone to cracking in the screw area for those latches.
Availability: In-Stock Item
Item #: 15705 -
Reproduction polished stainless steel door strikers for your Mercury Cougar or Ford Mustang. This kit includes stainless steel hardware and will make your door jambs pop.Replaces Ford part # C5AZ-6222008-A.
Availability: Used / Wrecking Yard Item
Item #: 11-0314 -
Used passenger side (right hand) complete door latch assembly for the Mercury Cougar XR7 or Ford Mustang with door ajar option. This unit goes inside your door and catches on the door striker assembly on the door jamb. Tested and inspected, this latch does the have the provision for the door ajar switch as found on all XR7 models. Door ajar switch sold separtely. This will fit all years 1967-70, was used as a service replacement. Just has a shorter tab for the key lock rod. Must use...
Availability: Used / Wrecking Yard Item
Item #: 11-0315 -
Used driver side (left hand) complete door latch assembly for the Mercury Cougar XR7 or Ford Mustang with door ajar option. This unit goes inside your door and catches on the door striker assembly on the door jamb. Tested and inspected for excessive wear. This latch does have the ability to mount the door ajar switch, as found on all XR7 models. Door ajar switch sold separately. Must use the 1969-70 door ajar switch with this mechanism. Ford part # C9AZ-6221813-A. ...
Availability: In-Stock Item
Item #: 10109 -
These are the screws that secure the door latch mechanism to the door shell. These screws come with the attached crown headed lock washer, just like the originals, so be sure to tighten them down snugly to ensure that the screw head sits flush into the screw holes. Sold individually. Three required per door, six per car.
Availability: Used / Wrecking Yard Item
Item #: 11-0235 -
Door lock latch lever, for driver or passenger side locks. Attach with an "E" clip on the rear side of the lock mechanism. Used "E" clip is included. We are going to say that these fit all Ford door locks 1965 through 1973 and beyond. *Note you will need to purchase or reuse your retainer clip for attaching the lock rod. Retainer clip not included, we have good used or reproduction clips, see related items.Ford number stamped C5AB-6221970-A or D2AB-6221970-AA ...
Availability: Used / Wrecking Yard Item
Item #: 11-0262 -
1969-70 Mercury Cougar and Ford Mustang latch rod that links the door latch and the inside door handle, right or left side door. Normally this rod was fabric covered. Used rod only, no retaining end clips.Replaces Ford part number C9ZZ-6521940-B.
Availability: Used / Wrecking Yard Item
Item #: 11-0303 -
Used interior door release mechanism. Other Ford names include: door remote, control, linkage assy, latch assembly. The spring is the weak link on these parts. Passenger and driver side are different, this is for the passenger side only, comes with attaching parts as shown. Replaces Ford part number C9AB-6221818-A.
Availability: Used / Wrecking Yard Item
Item #: 11-0302 -
Used interior door release mechanism. Other Ford names include: door remote, control, linkage assy, latch assembly. The spring is the weak link on these parts. Passenger and driver side are different, this is for the driver side only, comes with attaching parts as shown. Replaces Ford part number C9AB-6221819-A.
Availability: Used / Wrecking Yard Item
Item #: 11-0323 -
Plastic insert with metal locking retainer. The plastic came in various colors, white, red, and black are common.
Replaces Ford part # C5AZ-6221952-A.Check out our handy diagram below to find other '67-'68 door parts you may need. All the item numbers shown can be typed in to the search bar on our site. (Click image to view full size) ...
Availability: In-Stock Item
Item #: 22621 -
Reproduction rubber bumper for your 67 - 73 Cougar or Mustang door latch mechanism. The bumper sits on the inside of your door latch mechanism, and is there to dampen the blow from the striker when you close your door.
Availability: In-Stock Item
Item #: 30845 -
When ordering this item, you do not need to order a key blank, the key is included. If you need more than one key, you don't need to pay for multiple key cutting services, just buy extra blanks and mention it in the comment section of your order. This listing is for the ECONOMY version of the trunk / glove box key. We now have the ability and equipment from an old Lincoln Mercury dealership to cut keys for Fords "by the numbers". Instead of copying a worn key to make yet another key that...
Availability: Used / Wrecking Yard Item
Item #: 11-0461 -
Refurbished pair of door lock cylinders and ignition cylinder for all double cut key Fords 1970-73. These are coded to the original key code, which was stamped onto one of the door lock cylinders. Sometime after 1973, Ford changed the ignition lock cylinder end. We know it works through 1973, not sure of the change. It must fit the brass lock gear at the bottom of the cylinder hole in the side of the steering column. Refer to your shop manual for removal and installation. Includes two...
Spotlight!
Featured!
Availability: In-Stock Item
Item #: 32134 -
When ordering this item, you do not need to order a key blank, the key is included. If you need more than one key, you don't need to pay for multiple key cutting services, just buy extra blanks and mention it in the comment section of your order. We now have the ability and equipment from an old Lincoln Mercury dealership to cut keys for Fords "by the numbers". Instead of copying a worn key to make yet another key that doesn't fit properly, we can cut keys as they would have come from the...
Availability: Out of Stock
Item #: 42379 -
Since our restored emblems look so good we have a hard time selling NOS these days which works out just fine as we only seem to be able to obtain 1 of these every few years. Keep in mind your used cores have trade in value against this NOS part. Casting number seen on back side for the assembly is C9WB-65517A56-A and black plastic is C9WB-65517C00-A, Casting number on chrome is C9WB-65517A20-A
Availability: In-Stock Item
Item #: 12582 -
These fuel door Mercury crest emblems have been lovingly restored by a long time Cougar enthusiast. They have been carefully repainted the correct colors and will really liven up the looks of the rear of your 1969 - 1970 Cougar. This crest was used on all models except the 1970 Eliminator. The engineering number on the back is C9WB-65405A92. To remove your emblem we suggest grinding down the studs on the backside. To install the restored emblem you will have to use epoxy glue. Keep in mind you...
Availability: Out of Stock
Item #: 21-0050 -
Good used plastic emblem with no peeling chrome. This was used on all models except XR7 on the right side. We also have the metal version of this emblem available.
Availability: Used / Wrecking Yard Item
Item #: 23604 -
You may consider buying our grade "B" door over our grade "A" door if you are doing a high end restoration. Here is the reasoning; due to the design of the 69-70 door, silt is trapped in all of the door corners, these tight recesses always have silt collected in them and when you add moisture you get corrosion. Our grade "A" doors do not have noticeable blisters but since there is no paint or sound deadener in the depths of the corners we know there is some amount of corrosion taking place...
Availability: In-Stock Item
Item #: 19392 -
These are the same left to right, convertible or coupe. These appear to be made from the same thickness of aluminum as original and weigh .44 pounds as opposed to .50 for the originals but the aluminum used is not nearly the quality of originals. You can literally mutilate these parts with your fingers as you would an aluminum can. We recommend the premium quality sills. These are a poor reproduction that will not hold up well over time, we cannot recommend this part. We HIGHLY recommend...
Availability: Used / Wrecking Yard Item
Item #: 24852 -
Worn, scratched, dull but usable. Will have dents from seat belts.
Featured!
Availability: In-Stock Item
Item #: 25918 -
Ford never made these in stainless but what a great upgrade! The advantage we see with these is that they do not dent or scratch as easy when you release your seat belt. They also can be polished easily (unlike anodized aluminum). These weigh 1.5 pounds each, triple of what the originals weigh. Sold as a pair only. *NOTE* Since these are stainless they look great next to our "accessory" stainless steel sill plates we offer. The secondary "accessory" strips cover the painted portion of the door...
Availability: In-Stock Item
Item #: 19464 -
These weigh .50 pounds each, exactly as the originals do. Just like the originals, these are very prone to scratches and dents, even letting your seat belt fall will mark them up. Although these sill plates are better than our economy version, we still rate them below OEM which was also prone to damaging easily. We HIGHLY recommend the stainless version we sell. These are sold individually, coupe, convertible, left and right are all the same. Decals are sold...
Availability: In-Stock Item
Item #: 41142 -
One size fits all. Set of 4. Good replacement if not worried about show quality. 1967 – 1968 Coupe 6 Required per car 1969 – 1973 Coupe 4 required per car 1969 – 1973 Convertible 2 required per car Will also work on the 69 - 73 shifter bezels. 4 required. Not recommended for our Mass Backed Carpeting. Please see related items for the longer screws. Replaces Ford Part #: 381571-S
Availability: In-Stock Item
Item #: 15408 -
This quality kit includes gaskets and buttons for both the passenger and driver side. The fit and finish is perfect on these, No excuses here, satisfaction guaranteed. These fit many Lincoln / Mercury / Ford products such as the 1970-71 Torino, Cyclone, Ranchero, Fairlane, Australian Falcon / Cobra. THESE ARE NOT THE SAME AS MUSTANG! Replaces Ford part numbers C6OZ-6222404-A and C6OZ-6222405-A ...
Availability: Out of Stock
Item #: 10073 -
Pair of reproduction door pull straps for the 1969 - 1970 Mercury Cougar. Keep in mind that between 69 and 70 there were two different versions of each color. For example, 1969 had the dark green and 1970 had a lighter green...so be sure to order the correct year!
Availability: In-Stock Item
Item #: 32158 -
8-32 x 1 inch long screws for attaching automatic shift bezels on 1969-73 Mercury Cougar or Ford Mustang with added Mass Backed Carpeting. Shiny zinc screws as shown, set of 4. Replaces Ford Part #: 381571-S
Availability: Used / Wrecking Yard Item
Item #: 11-0202 -
This is the round metal threaded disc that attaches the D0ZZ-6523258-A bushing to the door glass brackets. About 1-3/4" in diameter, two each per door glass on a 1970. 1971-73 Mercury Cougar and Ford Mustang use 3 of these for retaining the door channel bracket. Ford part number 384289-S.Click on images to enlarge. Do you have questions about Glue-In vs Bolt-In glass? How about how to properly install Glue-In glass in your 1969 Cougar or Mustang? Check out our video below for some great glassy...
Availability: Used / Wrecking Yard Item
Item #: 11-0456 -
57084-S Attaching bolt with 7/16" hex head and captured washer. Among other things, it is used to attach the door run, window stops (all 3), both window stabilizers, and the window regulator. Same bolts for manual and power window regulators. Bolt sold individually, there are a good handful in each door. This bolt is used for bolting in the bolt-in glass on 1970, lower "L" bracket for rear quarter windows on 1971-73 Cougar and Mustangs.
Availability: Used / Wrecking Yard Item
Item #: 11-0243 -
Used quarter window stop, cover plate, for any 1969-70 Mercury Cougar and Ford Mustang. These were originally painted body color, and were laid on either inside the front cowl or the package tray for painting. The one for the quarter is roughly1" x 2-7/16 inches long, the holes are 5/16, and the spacing is 31/32" on center to match the stop. Replaces Ford part number C9ZZ-6530068-A.
Availability: Used / Wrecking Yard Item
Item #: 11-0256 -
C9AZ-6521760-A Front door window stop bracket. Stops the window in the up position. Application 1969-70 Mercury Cougar and Ford Mustang including Mach 1. One per door.Same bracket is used on both driver and passenger sides.
Availability: Used / Wrecking Yard Item
Item #: 11-0260 -
Used door window stop, cover plate, for any 1969-70 Mercury Cougar and Ford Mustang. These were originally painted body color, and were laid on either inside the front cowl or the package tray for painting. The one for the doors is roughly 25/32" x 3-3/8 inches long, the holes are 5/16, and the spacing is 1-25/32 on center to match the stop. Replaces Ford part number C9ZZ-65234A30-A.
Availability: Out of Stock
Item #: 26144 -
Almost identical to the original, tab is a bit longer. *NOTE*1969 Cougar owners do not need this part as it is built in the the chromed plastic, rectangular bezel on the door panel.
Availability: In-Stock Item
Item #: 26150 -
Great reproduction of a rather hard to find part.
Availability: In-Stock Item
Item #: 26777 -
*NOTE* EARLY 69's USED THE 2112 MIRROR FOR BOTH PASSENGER AND DRIVER SIDES. LATE 69's USED TWO DIFFERENT SIZES FOR EACH SIDE (2124 for driver side, and 2112 for passenger side). BEFORE ORDERING, PLEASE CHECK YOUR DIMENSIONS AND COMPARE TO OUR LISTINGS. Precision cut replacement lens for any Ford product with sport mirror on the passenger side. This fits any FoMoCo Sport mirror 69 and up, left hand only. Comes with two round pieces of double sided tape. Keep in mind if your lens is bad and it...
Availability: Out of Stock
Item #: 41247 -
Reproduction side view mirror screw. These screws are sold individually. Do you have riv-nut questions? Here are riv-nut answers!
Availability: In-Stock Item
Item #: 13741 -
Reproduction passenger side (right hand) sport mirror lens for the Mercury Cougar or Ford Mustang and Torino.The mounting screw, that holds the mirror assembly in, is not included by default but is an optional addon. Replaces Ford part # C9AZ-17698-B. Dimensions: 4 7/16" x 2 15/16" This version does NOT include the wording "objects in mirror are closer than they appear". We also sell the version with the wording. Do you have questions about installing a passenger side mirror or using...
Availability: Used / Wrecking Yard Item
Item #: 24774 -
Empty shell / head / housing only for a passenger side manual adjust mirror. Found on all FoMoCo products utilizing a manual mirror 1969 - 1973. The remote mirror heads found on many 1970's Ford products do not interchange with the manual "Bullet Style" mirrors. Most customers find our reproduction unit to be a better value as it comes with the mirror and mounting hardware. Do you have questions about installing a passenger side mirror or using Riv-Nuts? Have more questions about installing a...
Availability: Out of Stock
Item #: 24775 -
Lens with mounting hardware only for a passenger side manual adjust mirror. Found on all FoMoCo products utilizing a manual mirror 1969 - 1973. The remote mirror lens assemblies found on many 1970's Ford products do not interchange with the manual "Bullet Style" mirrors. Count on the glass being scratched. The value here is in adjustment / mounting hardware. This unit will be guaranteed to keep its adjustment and not be loose like many have become over the years. Keep in mind this item is...
Availability: Used / Wrecking Yard Item
Item #: 25034 -
Used passenger side (right hand) sport mirror for the Mercury Cougar Eliminator. The Ford service replacement part number for the complete assembly is DOOZ-17682-D with a casting # on the base that reads D0OB-17713-AW. This is the correct right hand mirror for your 1970 Eliminator. It was available over the Ford counter to be placed on any 1969-70 Cougar but the 1970 Eliminator is the only model that came from the factory with it. Unlike the driver side door there is no factory embossed area...
Availability: Used / Wrecking Yard Item
Item #: 25127 -
If your mirror is fine except a broken off wand (control lever) it is an easy fix. Since the wand is made of a soft metal it is not too hard to drill out the old and replace it with one of our threaded replacement units. One can also remove the entire adjuster assembly form another mirror that has a broken base and carefully attach it. If you have some good used 1970 mirrors for sale with or without the wand intact we would like to hear from you as these are getting very hard to find. Have...
Availability: In-Stock Item
Item #: 13889 -
Fits and looks identical to the 1970 mirror base but is slightly taller. The difference in height between the two versions is indiscernible to the naked eye. Very nice product, works well with original mirror heads, save your hardware. Do you have questions about installing a passenger side mirror or using Riv-Nuts? Have more questions about installing a passenger side mirror or using Riv-Nuts? Got a mirror lens that flops around in your Sport Mirror every time you hit a tiny bump in the road?...
Availability: In-Stock Item
Item #: 10665 -
We have created all of the components needed to economically install the steel nutsert or Riv-nut for the exterior mirrors that mount to the car doors. Our steel Riv-nut uses a 1/4 inch hole. You will need a 5/32 Allen or hex key, 3/8 inch wrench, and a 7/16 inch wrench. The Riv-nut needs to be assembled on the kit as shown prior to installation.
The assembly is installed flush, in the pre-drilled hole. The Allen wrench and the 7/16 are held stationary, while the 3/8 wrench is used to tighten...
Featured!
Availability: In-Stock Item
Item #: 26776 -
*NOTE* EARLY 69's USED THE 2112 MIRROR FOR BOTH PASSENGER AND DRIVER SIDES. LATE 69's USED TWO DIFFERENT SIZES FOR EACH SIDE (2124 for driver side, and 2112 for passenger side). BEFORE ORDERING, PLEASE CHECK YOUR DIMENSIONS AND COMPARE TO OUR LISTINGS. Precision cut replacement lens for any Ford product with sport mirror. This fits any FoMoCo Sport mirror 69 and up. Comes with two round pieces of double sided tape. Lens measures 4 3/8 X 2 7/8. Do you have questions about installing the...
Availability: In-Stock Item
Item #: 27041 -
Reproduction driver side (left hand) remote sport mirror for the Mercury Cougar XR7. This unit will come with a primered base and head so that you can paint it to match the rest of your car. If you have some good used 1970 mirrors for sale with or without the wand intact we would like to hear from you as these are getting very hard to find! 1970 was the first year you could get a factory installed sport mirror on your XR7, Sports Special, or Eliminator. If you would also like to have a...
Availability: In-Stock Item
Item #: 27042 -
Reproduction passenger side (right hand) manually adjusted sport mirror for the Mercury Cougar or 1970-1971 Ford Torino / Cobra / Ranchero / Cyclone. Our kit includes everything needed to mount a bullet style sport mirror to the passenger side of your vehicle. This reproduction unit is far more durable than the originals which were cast with a softer metal. The Ford service replacement part number for the original complete assembly was D0OZ-17682-D. The base in...
Availability: In-Stock Item
Item #: 30630 -
Reproduction convex lens for a passenger side manual adjust mirror. Found on all FoMoCo products utilizing a manual mirror 1969 - 1973. The remote mirror lens assemblies found on many 1970's Ford products do not interchange with the manual "Bullet Style" mirrors. The screw that holds the mirror assembly in, is not included by default but is an optional addon. Replaces Ford part # C9AZ-17698-B This version included the words "objects in mirror are closer than they appear". We also sell the...
Availability: Used / Wrecking Yard Item
Item #: 11713 -
We highly recommend restoring our rust free Western hinges over using reproduction hinges. The main reason the originals are better than the Taiwan made reproductions is fit. If there is anywhere in which you want a precision fit it is in the hinges. These hinges have not been worn to the point of being "hogged out" and have been carefully inspected for cracks.You will want to purchase a new hinge pin and 2 bushings though. ...
Availability: In-Stock Item
Item #: 19406 -
Includes 4 cut to length hinge pins and 8 hinge bushings. Replaces Ford Part #: C9ZZ-6522800
Availability: In-Stock Item
Item #: 11715 -
Most times you do not need new hinges but rather new bushings and pins. If your hinges are such that the holes are "hogged out" and no longer seat the bushing firmly then you will need to buy one of our good used hinges that come with new bushings and pin. These overseas hinges are not known for fitting well, we cannot recommend them and we do not accept returns or exchanges on them. Replaces Ford part #: C9ZZ-6522810-A. ...
Availability: Used / Wrecking Yard Item
Item #: 11717 -
We highly recommend restoring our rust free Western hinges over using reproduction hinges. The main reason the originals are better than the Taiwan made reproductions is fit. If there is anywhere in which you want a precision fit it is in the hinges. These hinges have not been worn to the point of being "hogged out" and have been carefully inspected for cracks. You will want to purchase a new hinge pin and 2 bushings though. ...
Availability: In-Stock Item
Item #: 11723 -
Most times you do not need new hinges but rather new bushings and pins. If your hinges are such that the holes are "hogged out" and no longer seat the bushing firmly then you will need to buy one of our good used hinges that come with new bushings and pin. These overseas hinges are not known for fitting well, we cannot recommend them and we do not accept returns or exchanges on them. Replaces Ford part # D0ZZ-6522801-A. ...
Availability: In-Stock Item
Item #: 11724 -
Most times you do not need new hinges but rather new bushings and pins. If your hinges are such that the holes are "hogged out" and no longer seat the bushing firmly then you will need to buy one of our good used hinges that come with new bushings and pin. These overseas hinges are not known for fitting well, we cannot recommend them and we do not accept returns or exchanges on them. Replaces Ford part #: D0ZZ-6522800-A. ...
Availability: Used / Wrecking Yard Item
Item #: 42016 -
We highly recommend restoring our rust free Western hinges over using reproduction hinges. The main reason the originals are better than the Taiwan made reproductions is fit. If there is anywhere in which you want a precision fit it is in the hinges. These hinges have not been worn to the point of being "hogged out" and have been carefully inspected for cracks. You will want to purchase new pins and bushings though. ...
Availability: In-Stock Item
Item #: 42025 -
Most times you do not need new hinges but rather new bushings and pins. If your hinges are such that the holes are "hogged out" and no longer seat the bushing firmly then you will need to buy one of our good used hinges that come with new bushings and pin. These overseas hinges are not known for fitting well, we cannot recommend them and we do not accept returns or exchanges on them. Replaces Ford part # C9ZZ-6522811-A. ...
Availability: Used / Wrecking Yard Item
Item #: 42037 -
We highly recommend restoring our rust free Western hinges over using reproduction hinges. The main reason the originals are better than the Taiwan made reproductions is fit. If there is anywhere in which you want a precision fit it is in the hinges. These hinges have not been worn to the point of being "hogged out" and have been carefully inspected for cracks. You will want to purchase new pins and bushings though. ...
Availability: In-Stock Item
Item #: 25997 -
Due to the small amount of clearance between the back of your speaker and the door glass when lowered, these and the 60 Watt Kenwood version of this speaker are the only speakers on the market that will replace your worn out originals and fit like OEM without modifications. Rated at 30 watts peak power and 4 ohms. Nice upgrade over the low wattage originals. Sold as a pair only. Replaces Ford part # C9ZZ-18808-A.
These pictures show what every 69-70 door panel looks like on the...
Availability: Out of Stock
Item #: 26006 -
Due to the small amount of clearance between the back of your speaker and the door glass when lowered, these and their 30 watt little brother are the only speakers on the market that will replace your worn out originals and fit like OEM without modifications. Features Kenwood 60 watt peak power speakers, nice upgrade over the low wattage originals. Sold as a pair.
These pictures show what every 69-70 door panel looks like on the backside. They are all perforated from from the...
Availability: In-Stock Item
Item #: 41840 -
Economy quality door speaker covers made from plastic injection. This version does not have a metal grille, the entire grille is made of plastic. In most situations we would recommend the Premium version as it has metal grilles; the all plastic version will cover the hole and will look correct if you don't inspect them closely, but is much easier to accidentally punch a hole in and will not stand up as well over time. The economy version also has a "Stereo" sticker instead of the correct...
Availability: Used / Wrecking Yard Item
Item #: 18905 -
Sold individually, prior to purchase you will have to email us for colors on hand, as we do not have very many in top condition. The repro version of this grille is very good, so the only reason you would buy used is if you want a certain color (reproductions only come in black) or if you only needed one side.
Availability: In-Stock Item
Item #: 31064 -
Premium quality door speaker covers that have the OE correct durable metal grille mesh, unlike the economy version which is made entirely from plastic. The plastic version is much easier to accidentally punch a hole in and will not stand up as well over time. These grills also include the original style aluminum "stereo" decals, as compared to the economy version which has a simple sticker. Sold as a pair.All 1969-70 Mustang and Cougar door panels are equipped with a factory perforated "knock...
Availability: Used / Wrecking Yard Item
Item #: 11-0362 -
Good original passenger side door latch rod set. Includes rod for inside lock, outside key lock, and outside door release actuating rod. These are good used parts and are a better quality and value compared to the reproductions. Only fits passenger side doors of 1969-70 Mercury Cougar.*Note will not fit Mustang due to the door handle difference.
Availability: Used / Wrecking Yard Item
Item #: 11-0363 -
Good original driver side door latch rod set. Includes rod for inside lock, outside key lock, and outside door release actuating rod. These are good used parts and are a better quality and value compared to the reproductions. Only fits driver side doors of 1969-70 Mercury Cougar.* Note will not fit Mustang due to the door handle difference.
Availability: Used / Wrecking Yard Item
Item #: 11-0266 -
1969-70 Mercury Cougar and Ford Mustang door lock rod. This is the short rod that goes between the door key lock and the latch mechanism. Same part right or left, just under 6 inches in length, no threads on this rod. Ford part number C9ZZ-6522134-A.
Availability: Used / Wrecking Yard Item
Item #: 11-0267 -
Ford called this small door latch part an adjuster. It threads onto the bottom of the door latch rod inside the door. Common to most Ford products 1965-1970. Ford part number C5AZ-62218106-A.
Availability: Used / Wrecking Yard Item
Item #: 11-0271 -
Ford calls this Rod - Door Latch Push Button. This is the inside passenger side manual door locking rod. Side specific to the passenger side on any 1969-70 Mercury Cougar and Ford Mustang. The threaded end is where the chromed plastic manual lock button attaches. The lower end hooks onto the door latch. Ford part number C9ZZ-6521852-A.
Availability: Used / Wrecking Yard Item
Item #: 11-0273 -
Door latch actuating rod with adjuster for all 1969-70 Mercury Cougar and Ford Mustangs. Curved end hooks to the outside door release button lever. The threaded lower end with adjuster attaches to the latch mechanism. Main threaded rod has a Ford part number of C9ZZ-6522152-A. Adjuster has a Ford part number of C5AZ-6221816-A. Same rod fits either the passenger or driver side doors.
Availability: Used / Wrecking Yard Item
Item #: 11-0277 -
Ford calls this Rod - Door Latch Push Button. This is the inside driver side manual door locking rod. Side specific to the driver side on any 1969-70 Mercury Cougar and Ford Mustang. Your chromed plastic lock knob threads onto the threaded end, the lower end hooks onto the door latch. Ford part number C9ZZ-6521853-A.
Availability: In-Stock Item
Item #: 30757 -
Reproduction Concours correct door lock rod anti rattle sleeve. This will come in a 33" length, and is cut-to-fit.
Availability: In-Stock Item
Item #: 26102 -
Protects door panels from the abrasive action of rotating handles. Made from a very hard nylon type material featuring the correct milky white color. Replaces Ford Part Number #C8AZ-6223370-ADiameter 1-1/2"
Availability: In-Stock Item
Item #: 41434 -
This handle is a good replacement for the window cranks found on the 1971 - 1972 Cougar both front and back. The originals were 4 1/4" total length and this replacement handle is 4 7/8" long. The important detail on these is the fact that the female portion that attaches to the splined window regulator protrudes from the back 5/16". If you are using our chrome backing plates on your 69 -70, then this is the crank you will need to provide the correct clearance.Used before 10/71,...
Availability: Used / Wrecking Yard Item
Item #: 24329 -
C8AB-7630323-A Usually these will not have knobs. Plan on purchasing new knobs. Ask about our B grade knobs that will have some pitting or lusting issues. This is the correct "shorty" crank for a 1968 Cougar front window crank. It is the same length as the rear 1968 - 1970 but uses a center screw instead of a side Allen set screw. The 1969 - 1970 crank (with AM or no radio) looks the same but is longer. These shorter cranks were also used in conjunction with the factory door speakers used in...
Availability: Used / Wrecking Yard Item
Item #: 24330 -
We often will have B grade knobs with less than great chrome plating for lots less money. Plan on ordering new knobs, we have lots of colors to choose from.This is a good used original front window crank with no obvious scratches or pitting. It will be missing the decal that covers the screw sometimes it will have a knob, most often it will not. Ford part number is C8AZ-6223342-A, casting number on back reads C8AB-6223348-B or D0AB-6223348. *NOTE* This handle will work on a 1968 even though it...
Availability: Used / Wrecking Yard Item
Item #: 24514 -
This is a good used original rear window crank with no obvious scratches or pitting. May or may not come with random colored knob. It most likely will be missing the decal but will have the original set screw. Ford part number is C8ZZ-6530322-A, casting number shown on back is C8ZB-6530323-A. Black knobs are the most commonly ones requested, plan on buying new knobs if you need black.
Availability: In-Stock Item
Item #: 13868 -
Best quality of the three version made and the only one that comes with the decal installed. This is held on by an Allen set screw, we often get calls from people who cannot figure out how to remove these. Check our good used cranks if you like to keep original FoMoCo parts on your Cougar. Replaces Ford part number C8ZZ-6530322-A.
Availability: In-Stock Item
Item #: 13869 -
This is actually not correct for a 1968 but it is all that is available in reproduction. The 1968 front is actually the same 4 1/4" length as the rear. Many people prefer the longer version as it makes it easier to roll up. We do have good used 1968 front cranks for those who prefer to stay with original. The portion that attaches to the splined shaft on the window regulator protrudes from the back 3/16" (as shown on the left in the comparison picture) and will not clear the 71-73 door panels...
Availability: In-Stock Item
Item #: 13896 -
Easy to install quality reproduction. Sorry, aqua is not available at this time. Includes crescent spring and correct aluminum pin that features shoulder and locking knurls. Fits 1968-71 cars and about 1 month into 1972. Please see the window crank handles to see the difference between 1968-71 handles and 1972-73 window crank handles. Replaces Ford Part # C8AZ-6223352 *TIP* To install remove your window crank and place knob and crank in the jaws. To protect the knob you will want to place a...
Availability: In-Stock Item
Item #: 13899 -
Easy to install quality reproduction. Sorry, aqua is not available at this time. Includes crescent spring and correct aluminum pin that features shoulder and locking knurls. Fits 1968-71 cars and about 1 month into 1972. Please see the window crank handles to see the difference between 1968-71 handles and 1972-73 window crank handles. Replaces Ford Part # C8AZ-6223352 *TIP* To install remove your window crank and place knob and crank in the jaws. To protect the knob you will want to place a...
Availability: Out of Stock
Item #: 13900 -
Easy to install quality reproduction. Includes crescent spring and correct aluminum pin that features shoulder and locking knurls. Fits 1968-71 cars and about 1 month into 1972. Please see the window crank handles to see the difference between 1968-71 handles and 1972-73 window crank handles. Replaces Ford Part # C8AZ-6223352 *TIP* To install remove your window crank and place knob and crank in the jaws. To protect the knob you will want to place a clean rag over the jaws. Place a small socket...
Availability: In-Stock Item
Item #: 13901 -
Easy to install quality reproduction. Includes crescent spring and correct aluminum pin that features shoulder and locking knurls. Fits 1968-71 cars and about 1 month into 1972. Please see the window crank handles to see the difference between 1968-71 handles and 1972-73 window crank handles. Replaces Ford Part # C8AZ-6223352 *TIP* To install remove your window crank and place knob and crank in the jaws. To protect the knob you will want to place a clean rag over the jaws. Place a small socket...
Availability: In-Stock Item
Item #: 13902 -
Easy to install quality reproduction. Includes crescent spring and correct aluminum pin that features shoulder and locking knurls. Fits 1968-71 cars and about 1 month into 1972. Please see the window crank handles to see the difference between 1968-71 handles and 1972-73 window crank handles. Replaces Ford Part # C8AZ-6223352 *TIP* To install remove your window crank and place knob and crank in the jaws. To protect the knob you will want to place a clean rag over the jaws. Place a small socket...
Availability: In-Stock Item
Item #: 13903 -
Easy to install quality reproduction. Includes crescent spring and correct aluminum pin that features shoulder and locking knurls. Fits 1968-71 cars and about 1 month into 1972. Please see the window crank handles to see the difference between 1968-71 handles and 1972-73 window crank handles. Replaces Ford Part #C8AZ-6223352-GR *TIP* To install remove your window crank and place knob and crank in the jaws. To protect the knob you will want to place a clean rag over the jaws. Place a small...
Availability: In-Stock Item
Item #: 13904 -
Easy to install quality reproduction. Includes crescent spring and correct aluminum pin that features shoulder and locking knurls. Fits 1968-71 cars and about 1 month into 1972. Please see the window crank handles to see the difference between 1968-71 handles and 1972-73 window crank handles. Replaces Ford Part # C8AZ-6223352 *TIP* To install remove your window crank and place knob and crank in the jaws. To protect the knob you will want to place a clean rag over the jaws. Place a small socket...
Availability: In-Stock Item
Item #: 13906 -
Perfect fit, great reproduction. These plastic discs are found on all 69-70 convertibles on the rear of both decor and xr7 interior levels. We are unclear as to all the "exact" applications on all years and models but one application we have verified is the fronts of 1971 - 73 Cougars equipped with standard interior. The reason the standard interior 71-73 Cougars came with these is that the door panels were very thick on the 71-73 decor / XR7 models and quite thin on the standard models and...
Availability: In-Stock Item
Item #: 41399 -
Complete Chrome Handle and metal bracket with rubber bumper assembled. Exact reproduction ready to bolt on. Replaces Ford Part Number C9ZZ-6522600.
Availability: In-Stock Item
Item #: 41400 -
Complete Chrome Handle and metal bracket with rubber bumper assembled. Exact reproduction ready to bolt on. Replaces Ford Part number C9ZZ-6522601.
Availability: In-Stock Item
Item #: 14976 -
Complete Chrome Handle and metal bracket with rubber bumper assembled. Exact reproduction ready to bolt on. Replaces Ford Part number C9ZZ-6522600 on the right and C9ZZ-6522601 on the left.
Availability: Used / Wrecking Yard Item
Item #: 11-0316 -
Our used handles do not come with this linkage part so if yours is missing this is what you need. Comes with mounting screw as shown.
Availability: In-Stock Item
Item #: 13976 -
Made in America using original Ford tooling. No excuses, premium quality part. Right is the same as left.
Availability: Used / Wrecking Yard Item
Item #: 11-0088 -
This used button comes with the original spring and rubber grommet as shown. Our new door handle kits do not come with the spring shown here so if you need these small items to complete your handle assembly this is the listing for you! Also fits Torino, Ranchero.
Availability: Used / Wrecking Yard Item
Item #: 11-0463 -
Our used handles do not come with this linkage part so if yours is missing this is what you need. Comes with mounting screw as shown.
Availability: In-Stock Item
Item #: 10002 -
This is a good reproduction of the original Ford part designed to fit Cougars, as well as many Lincoln / Mercury / Ford products such as the 1970-71 Torino, Cyclone, Ranchero, Falcon / Cobra. THESE ARE NOT THE SAME AS MUSTANG!Ford part # C6OZ-6222404-A.
Availability: In-Stock Item
Item #: 10003 -
This is a good reproduction of the original Ford part designed to fit Cougars, as well as many Lincoln / Mercury / Ford products such as the 1970-71 Torino, Cyclone, Ranchero, Falcon / Cobra. THESE ARE NOT THE SAME AS MUSTANG!Ford part # C6OZ-6222405-A.
Availability: Used / Wrecking Yard Item
Item #: 31173 -
Driver side taillight socket with wiring pigtail for the 69 - 70 Mercury Cougar. This is the socket that sits in the outer position of your taillight section.
Availability: Used / Wrecking Yard Item
Item #: 31174 -
Driver side taillight socket with wiring pigtail for the 69 - 70 Mercury Cougar. This is the socket that sits in the center position of your taillight section.
Availability: Used / Wrecking Yard Item
Item #: 31175 -
Driver side taillight socket with wiring pigtail for the 69 - 70 Mercury Cougar. This is the socket that sits in the inner position of your taillight section.
Availability: Used / Wrecking Yard Item
Item #: 31176 -
Passenger side taillight socket with wiring pigtail for the 69 - 70 Mercury Cougar. This is the socket that sits in the outer position of your taillight section.
Availability: Used / Wrecking Yard Item
Item #: 31177 -
Passenger side taillight socket with wiring pigtail for the 69 - 70 Mercury Cougar. This is the socket that sits in the center position of your taillight section.
Availability: Used / Wrecking Yard Item
Item #: 31178 -
Passenger side taillight socket with wiring pigtail for the 69 - 70 Mercury Cougar. This is the socket that sits in the inner position of your taillight section.
Availability: Used / Wrecking Yard Item
Item #: 27404 -
Tested and working emergency or parking brake indicator switch. Foot parking brake switch found on 1969-70 Mercury Cougar and Mustang with visibility group option. Includes bolt to attach to emergency foot brake. Ford part number: C6GB-15652-A