All Available Parts - 1970 Mercury Cougar

Repro New Clear Windshield for Cougar. Replace that scratched and pitted old glass with the milky top, Our new glass is clear as rain, and works great too! BECAUSE OF THE HIGH COST OF SHIPPING, ALL WINDSHIELDS ARE AVAILABLE FOR DROP SHIP OR LOCAL PICK-UP ONLY. Our website is currently unable to accurately calculate truck freight costs, so don't be deceived by the shipping rate displayed. Keep in mind this is a common windshield that can be picked up locally from most any automotive glass shop....

Reproduction  Lower Windshield Moulding Retainer for the 1969 1970 Mercury Cougar or Ford Mustang  

Reproduction  Lower Windshield Moulding Center Spacer for the 1969 1970 Mercury Cougar or Ford Mustang  

Used spacer for the lower windshield moulding

Reproduction  Lower Windshield Moulding Fender Spacer for the 1969 1970 Mercury Cougar or Ford Mustang  

Original FoMoCo used two speed windshield wiper motor for your 1969-70 Mercury Cougar or Ford Mustang. This used motor comes with wiring harness with unique grommet for the firewall specific to 1969-70 Cougar and Mustangs. Motors are tested and guaranteed to work, 90 day warranty. Linkage arm for the 1969-70 installation, must be marked 9Z. Linkage arms sold separately. Ford part # C9ZF-17504-C.

Linkage arm that attaches to the windshield wiper motor that is unique to the 1969-70 Mercury Cougar and Ford Mustang. These are marked 9Z, among other things the slot is specifically indexed for the 69-70 Cougar and Mustang application. This is basically an installation kit that includes: linkage arm, flat bushing, wave washer, and nut. The order of installation is flat bushing, wave washer, linkage arm, and lastly the nut.

Electrical wiring pigtail for the windshield wiper motors on any 1969-70 Mercury Cougar or Ford Mustang. Plug with grommet and correct color wires and an adequate amount of wire length to make a repair or splice onto the newer motors without plugs.

Pair on reproduction lower windshield stops for all 1969-70 Mercury Cougar and Ford Mustangs

The hinges on these original arms tend to get worn out which will cause irregular movement and can eventually burn up your wiper motor or bind up the linkage. If your wipers do not move in tandem

This is the set of six bolts needed to attach the pivot section of the wiper arms to the cowl on 1969-1970 Cougars and Mustangs. Three bolts needed per side

Used windshield wiper motor cover or shield as Ford called it. Very prone to cracking and 'chalky' from age or UV light. We are not going to lie, most of these will have paint over spray or a slight amount of chalkiness. We haven't found a Ford part number other than the basic number of 17C441 which is labeled as "Shield - (Windshield Wiper Motor - Water)" as found in the Mercury MPC.

Original Trico stainless wiper holder assembly, removed from a 1970 Mercury Cougar. Fits any 1969-70 Mercury Cougar and Ford Mustang. Has the original metal fastener to connect to your wiper arm, rather than the plastic piece used in the reproductions. Sold individually, two per car, 16" rubber wiper blade not included.*Note - This is NOT, repeat NOT the ultra rare 1969 production wiper blade holder assembly. This is a Trico 16 inch blade holder as found on most 1970 cars.

OEM used. Rust and damage free. Installation gasket, clamps, and hoses are available. Fits 1970 20 gallon emissions fuel tank. DSO 52 and 53 California.

1970 California evaporative system. Tapered hose. This item is not reproduced and it is getting to be hard to find a good pliable hose with no damage.Filler neck not included.

Reproduction green tinted windshield that features a blue tinted band a crossed the top of the windshield. Not only will this unit look great, it will fit perfectly as well. Planning on installing the glass yourself? We also sell the glass to window channel weld. BECAUSE OF THE HIGH COST OF SHIPPING, ALL WINDSHIELDS ARE AVAILABLE FOR DROP SHIP OR LOCAL PICK-UP ONLY. Our website is currently unable to accurately calculate truck freight costs, so don't be deceived by the shipping rate displayed....

Best replacement for the original wiper blade assembly. Replaces Ford part #: D4AZ-17528 and C9AZ-17528-A. Sold individually

Set of 8 fine threaded Phillips screw assemblies. This the mechanism in which to adjust your headlights up or down, left or right. There are two units per bulb for a total of eight per car. The new screws that mount them to the grille are included at no extra cost. They will be in perfect working order and not rusty as we only keep the best examples. Two versions for 1967-68, the most common has the square corners and is rectangular, the other supplier had clipped corners as shown in the...

Quality "STANDARD" brand reproduction switch for your vacuum actuated hideaway headlights. This switch fits multiple years and makes which means multiple dash configurations. You will need to "break off" your unique extension and attach it to this unit. The extension (spacer) can be removed easily by placing your old switch in a vise and using a wedge shaped chisel to break the tiny spot welds. When reattaching, most any glue such as Gorilla glue, JB weld or even silicone will work as you are...

Hardware for mounting the hood bumpers on the radiator core support. Clip mounts with threads down, nut on top. Sold as a Kit as Pictured.

These simple little grille repair clips have been needed since these cars were new! Over the years I have seen many home remedies to fix this common problem but none were this clean looking, easy to install and failure proof. Soon we will list the all the different FoMoCo applications from the era that these clips apply to. These clips are sold as a set of four. Click on images to enlarge. ...

Powder Coated. Replaces Ford Part Number: C9ZZ-17385, correct for a 1969 Mustang or Cougar but works fine on a 1970 Cougar.

Used outer bushing for the hinge pivots for the hide-away headlights on the Mercury Cougar. Hole size is 5/8", shaft size is 3/8". Fits many of the Ford, Lincoln, Mercury cars with vacuum headlight covers. List includes 1969-71 Full size Ford Galaxie, LTD, XL, Country Squire, and Mercury Marquis, Brougham, and Monterey. Lincoln Continental starting in 1970 until? 1972-? Lincoln Mk IV. Also select Cylcone / Fairlane / Torino 1970-71 any with hide away headlights. Ford part # C9AZ-13A164-A. ...

C9AZ-13A164-B Inner grille bushing, where the hidden headlight hinge pivots. Hole size is 3/4", shaft size is 1/2". Fits many of the Ford, Lincoln, Mercury cars with vacuum headlight covers. List includes 1969-71 Full size Ford Galaxie, LTD, XL, Country Squire, and Mercury Marquis, Brougham, and Monterey. Lincoln Continental starting in 1970 until? 1972-? Lincoln Mk IV. Also select Cylcone / Fairlane / Torino 1970-71 any with hide away headlights.

C9AZ-13A163-C Coil spring for the hidden headlamp hinges on all 1969-70 Mercury Cougars and 1969 full sized Ford cars with hideaway headlights. Sold individually, one per side. 1969 Mercury Cougar including XR7 and Eliminator. 1969 Ford LTD 1969 Galaxie and Galaxie XL 1969 Country Squire Wagons

Used headlight wiring harness for either side of the Mercury Cougar. This harness is the sub-harness that connects your headlights to the under hood harness. The Cougar uses one per side and they are identical. Sold individually.Ford part # C9ZZ-13076-A, tagged C9ZB-13076-B.*NOTE* A pair of these units were also used on the 1969 Mustang and Mach 1. However, they were not used on the quad headlight 1970 Mustangs.

C9WY-13B014-A Shaft assembly for passenger side hideaway headlamps for any 1969 Mercury Cougar. Complete with rag joint and nut. Sold individually, one per side. These have become side specific due to time, and stress on those rag joints.

Shaft assembly for driver side hideaway headlamps for any 1969 Mercury Cougar. Complete with rag joint and nut. Sold individually, one per side. These have become side specific due to time, and stress on those rag joints.

1969-1970 Headlamp adjusting screw. Two per bulb, eight in all per car, comes with two new mounting screws. This part is identified by the clipped corners. Also used during 1967 and 1968 on a limited basis. Will be in good rust free condition as we only keep the best examples.Also sold in a set of 8. ...

Repro bushings (pair) that mount to the grille for the headlamp operating shafts. These hardly ever survive after 40 years. Technically not needed, and most never knew they existed. Sold as a pair, one for each side. When mounted these are tight, it was no wonder they are seldom seen on cars. Even the NOS bushings are tight. We recommend polishing the headlight shaft with emery or sand paper, to make both sides smooth. Definitely add a little bit of lubricant too. Replaces Ford part number...

Used hood latch for a 1969 Mercury Cougar, it will fit the 1970 too. Starting in 1969 until 1970, Mercury had three different hood latches. This late 1969 version has the medium length handle. Those early 1969 latches are a two finger operation for those of us with large hands. The part shipped will likely not be as clean as the one in the picture.Replaces Ford part number C9WY-16700-B.

Used passenger side (right hand) outer semi gloss black headlight adjusting ring that holds the headlight bulb in place of the Mercury Cougar. Marked C8AB-47-A and "L", There are four different versions used, but they are the same for the 1969-70 Cougars. They are secured by two adjusting screws and the stainless steel headlamp retaining ring that fits over it. These are rust free, taken from a Western parts car and are sold individually. This exact same ring was also used on 1967-68 Mercury...

Used passenger side (right hand) inner semi gloss black headlight adjusting ring that holds the headlight bulb in place of the Mercury Cougar. Marked C8AB-17-A and "H", There are four different versions used, but they are the same for the 1969-70 Cougars. They are secured by two adjusting screws and the stainless steel headlamp retaining ring that fits over it. These are rust free, taken from a Western parts car and are sold individually. This exact same ring was also used 1967-68 Mercury...

Used driver side (left hand) outer semi gloss black headlight adjusting ring that holds the headlight bulb in place of the Mercury Cougar. Marked C8AB-37-A and "L", There are four different versions used, but they are the same for the 1969-70 Cougars. They are secured by two adjusting screws and the stainless steel headlamp retaining ring that fits over it. These are rust free, taken from a Western parts car and are sold individually. This exact same ring was also used 1967-68, but was moved...

Used driver side (left hand) inner semi gloss black headlight adjusting ring that holds the headlight bulb in place of the Mercury Cougar. Marked C8AB-16A and "H", There are four different versions used, but they are the same for the 1969-70 Mercury Cougars. They are secured by two adjusting screws and the stainless steel headlamp retaining ring that fits over it. These are rust free, taken from a Western parts car and are sold individually. This exact same ring was also used...

Used set of 4, semi gloss black headlight adjusting rings that hold the headlight bulbs in place on the 1967-70 Mercury Cougar. There are four different versions used. They are secured by two adjusting screws and the stainless steel headlamp retaining ring that fits over it. These are mostly rust free, taken from a Western parts cars. All four individual headlight holding cups. These are mostly going to have the C8AB part numbers on them, which is what we have the most of. Included is cups...

Set of 8 1969-1970 Headlamp adjusting screw. Two per bulb, eight in all per car, comes with two new mounting screws. This part is identified by the clipped corners. Also used during 1967 and 1968 on a limited basis. Will be in good rust free condition as we only keep the best examples. Also sold individually.

This is what we classify as a grade "A" center grille with no cracks, pits or broken studs. Ships without running cat emblem in center.For the money, most people will want to buy our reproduction center grille that you can find here. This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit of 50% of our web price for parts delivered in hand or by carrier to our Brooks, Oregon location. If...

This portion of the grille bolts in between the eyelid and center grille. This is the best we have to offer in used condition with no pits, cracks or obvious scratches.

This portion of the grille bolts in between the eyelid and center grille. This is the best we have to offer in used condition with no pits, cracks or obvious scratches.

This 1970 eyelid is the portion of the grill that raises when you turn on your headlights. No cracks, pits or obvious scratches. Keep in mind we have grade B examples for half the price with only minor imperfections.

This eyelid is the portion of grill that raises when you turn on your headlights. No cracks, pits or obvious scratches. Keep in mind we have grade B examples for half the price with only minor imperfections.

This is the portion of the 1970 grill that ties it all together and mounts it to the core support. This grade A part has no cracks or broken spots where the headlight retainer rings mount. Keep in mind we have grade B examples for half the price with only minor imperfections. Check out this video ...

This is the portion of the 1970 grill that ties it all together and mounts it to the core support. This grade A part has no cracks or broken spots where the headlight retainer rings mount. Keep in mind we have grade B examples for half the price with only minor imperfections.

Used grade "B" grille headlight eyelid door for the Mercury Cougar.

Used grade "B" driver side (left hand) grille headlight eyelid door for the Mercury Cougar.

Captured washer, or spinning washer nut for attaching the headlamp motors or vacuum actuators on the 1969-70 Mercury Cougar. All models, Standard Hard Top, XR7, and Eliminator. Two needed per car, sold individually.

Spring that holds the headlight trim ring on each headlamp to the grille. 4 springs per car, sold individually.Ford number C6AZ-13031-C.

Requires you to PRE-PAY a core charge of $30. Used grade "B" headlight door actuator for your Mercury Cougar. This grade B actuator has been reconditioned with new seals but will still slowly leak down after time as not all of them will function as new after being reconditioned. These actuators are sold individually on an exchange basis or outright (for an additional core charge). One actuator actuates both headlight doors on the 69-70. This unit also comes with a 30 day warranty. Ford part #...

GORGEOUS! For less money than you can re-chrome and repaint an original you can now bolt on this show quality part and be done! Better chrome quality than a NOS grille, pre-drilled to accept a XR emblem or walking cat emblem as found on the ELIMINATOR or Standard model Cougar.  Wanna save $100 and get a blemished center grille? Check out the lisiting and read about the blems here. Check out this video ...

This bracket is used to mount the vacuum storage tank under the driver side fender. Same bracket as was used in 1967 just a slightly different clip.  Two required per car, sold individually. Cougar part number D0WY-13B008-A. *Note - The 1967 bracket was used prior to 11/10/1969 built date.

Good used tank as taken from a Western parts car. Differs from other years only in that the vacuum port is located in a different position. Keep in mind we have units that are not as clean but still hold vacuum for about half the price. Cougar part number D0WY-13A185-A.

This used original, color coded set of vacuum hoses is 100% complete and relatively pliable. It comes complete with decades of dirt and grime (patina) for no extra charge. If you want to remove the grime it will take some serious elbow grease but it can be done. The color coded stripes are quite resilient to cleaning as the ink used actually embedded itself into the rubber. If you have a tried and true method of cleaning these hoses let us know and if it sounds good we will post it here! Does...

Used Passenger Side Grade "B" Center Grille Support for the 1970 Mercury Cougar

Used Driver Side Grade "B" Center Grille Support for the 1970 Mercury Cougar

Used Passenger Side Grade "A" Center Grille Support for the 1970 Mercury Cougar

Used Driver Side Grade "A" Center Grille Support for the 1970 Mercury Cougar

D0WY-13B013-A Center section that connects to the vacuum motor on 1970 Mercury Cougar, including XR7 and Eliminator. The center piece is offset to the left of center and the hook part that goes to the vacuum motor points down.1969 and 1970 center shafts are not interchangeable.

Fits Standard and XR7 Sold as a Kit as Pictured.

Fits Standard and XR7 Sold as a Kit as Pictured. Check out this video

Attaching screws for the headlamp adjusting screws for the 1967-70 Mercury Cougar and most other Ford and Mercury cars and trucks. Each of the headlamp adjusting screws uses 2 of these screws. A Cougar with 4 headlights would need a total of 16 of these screws.

1970 Mercury Cougar hideaway headlight vacuum tank installation brackets (pair) with fasteners. Two different styles of installation brackets for the 1970 vacuum tank found inside the driver side fender. These are tall brackets, the other style utilized 1967 brackets with round spacers.

All parts needed are included to mount your 1970 vacuum storage tank to the core support (backside) under the driver fender. Solid, good original parts found on a Western donor Cougar. Includes short brackets with correct clips, 4 spacers, 4 long bolts with washers, and 4 shorter hex bolts. Typically this kit was used for installing the vacuum tanks until Nov 1969, it is much more convenient to use the more common later kit for the 1970 tank installation.

This is a tested original FoMoCo headlight switch that will work, there is no warranty. The primary reason we list these old used switches is that some people are missing their switch altogether and need the beveled cup shaped spacer that mates to the dash. As pointed out in our listing for the reproduction headlight switch, the spacer is not included with our new units. Ford part # D0WB-11652.

This conversion will replace the old, tired, vacuum system that likes to leak and wear out. There are few differences between the 1969 and 1970 conversion kit. This kit consists of an electric actuator assembly (new Mazda Miata motor) with a plug and play wiring loom for easy installation. Simply remove all existing vacuum components and replace with this kit to have headlight covers that work under any conditions with the car running or not. These new motors are smoother and more reliable...

Used grade "B" center grille for the 1970 Mercury Cougar. This may have a few cracks, will show some pitting and may have a few broken studs. A great option if you are looking to just fill a hole, but some people like our reproduction unit that you can find here. However, nothing beats original FoMoCo! ...

Used hood latch for a 1970 Mercury Cougar, it will fit the 1969 too. Starting in 1969 until 1970, Mercury had three different hood latches. This 1970 version has the longest handle, and is the easiest to operate. Those early 1969 latches are a two finger operation for those of us with large hands. The part shipped will likely not be as clean as the one in the picture.Replaces Ford part number D0WY-16700-B.

This is what we classify as a grade "A-" center grille with no cracks or broken studs. It does however show pitting. Includes XR7 center emblem as shown. We rarely have these complete units available.For the money, most people will want to buy our reproduction center grille that you can find here.We also carry the "7" background decal. This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit...

Set of 16 attaching screws for the headlamp adjusting screws for the 1967-70 Mercury Cougar and most other Ford and Mercury cars and trucks. Each of the headlamp adjusting screws uses 2 of these screws. A Cougar with 4 headlights would need a total of 16 of these screws.

Sold individually, black only. We have an array of colors in good used condition used. We also have the hard plastic bracket that this slips over. Four are required per car. Replaces Ford Part #: C8AZ-6229024-A.

These are the plastic brackets that screw to you roof and then slide the vinyl colored piece over. Sold individually, four are required per car. Replaces Ford part # C8AZ-6229232.

Reproduction roof / headliner insulation kit for your Mercury Cougar or Ford Mustang. An effective item that will increase the efficiency of your heater or A/C. This will also insulate your interior from outside sounds.

Two piece kit, one piece for the headliner, and a second piece for covering the sunroof panel.On early production cars Ford pulled the cars off the assembly line to sent them to ASC Golde for install. Golde used 3 bows for installing the headliner, whereas in later production Ford used 2 bows when installing them on the assembly line. These headliners are for 2 bows installations. If you have 3 bows, you will need to order a standard headliner, then cut it to fit. Check out our video below...

Reproduction interior windshield / A pillar post mouldings / trim that features a vinyl overlay and 2 inch gauge pods on the driver side (left hand) so you can add any gauges of your choice to your Mercury Cougar or Ford Mustang. These units are sold in pairs.

Interior windshield / A pillar post mouldings / trim for 69 - 70 Cougars and Mustangs that feature two 2" gauge pods on the driver side. Sold as a pair.  These are not the best fit but will work, notice it requires exterior screws to mount them. No returns.

This is the 1968 coupe version of the 2 hole front mounting sun visor center bracket and is a close match for the 1968 / 1969 / 1970 convertible sun visor bracket.  This bracket is not, however, an exact match for 1971 /1972 / 1973 convertible as some sites suggest, but it will work. On the 71 - 73, the hole spacing and distance from the windshield are identical to this bracket, but the bracket is not the same size. This bracket is 1/8" longer on the...

Reproduction Sun Visor Bracket & Rod for the 1967, 1968, 1969 and 1970 Mercury Cougar or Ford Mustang. Great quality and fit, left and right use same part, sold separately. Replaces Ford part # C7AZ-6204144-A.

Yet another incorrect reproduction sold by West Coast Classic Cougar and made by someone who has never even sat in a Cougar... I have no idea where these manufacturers get their color charts! At least you have a base in which to paint over with the correct color. Sorry, we never get good used units in these days. *NOTE* This would be a good time to purchase trunk filler boards and package tray if you need them as we can save you money by combining these like shaped items. ...

Yet another incorrect reproduction sold by West Coast Classic Cougar and made by someone who has never even sat in a Cougar... I have no idea where these manufacturers get their color charts! At least you have a base in which to paint over with the correct color. Sorry, we never get good used units in these days. *NOTE* This would be a good time to purchase trunk filler boards and package tray if you need them as we can save you money by combining these like shaped items. ...

Yet another incorrect reproduction sold by West Coast Classic Cougar and made by someone who has never even sat in a Cougar... I have no idea where these manufacturers get their color charts! At least you have a base in which to paint over with the correct color. Sorry, we never get good used units in these days. *NOTE* This would be a good time to purchase trunk filler boards and package tray if you need them as we can save you money by combining these like shaped items. ...

Yet another incorrect reproduction sold by West Coast Classic Cougar and made by someone who has never even sat in a Cougar... I have no idea where these manufacturers get their color charts! At least you have a base in which to paint over with the correct color. Sorry, we never get good used units in these days. *NOTE* This would be a good time to purchase trunk filler boards and package tray if you need them as we can save you money by combining these like shaped items. ...

Yet another incorrect reproduction sold by West Coast Classic Cougar and made by someone who has never even sat in a Cougar... I have no idea where these manufacturers get their color charts! At least you have a base in which to paint over with the correct color. Sorry, we never get good used units in these days. *NOTE* This would be a good time to purchase trunk filler boards and package tray if you need them as we can save you money by combining these like shaped items. ...

Yet another incorrect reproduction sold by West Coast Classic Cougar and made by someone who has never even sat in a Cougar... I have no idea where these manufacturers get their color charts! At least you have a base in which to paint over with the correct color. Sorry, we never get good used units in these days. *NOTE* This would be a good time to purchase trunk filler boards and package tray if you need them as we can save you money by combining these like shaped items. ...

Yet another incorrect reproduction sold by West Coast Classic Cougar and made by someone who has never even sat in a Cougar... I have no idea where these manufacturers get their color charts! At least you have a base in which to paint over with the correct color. Sorry, we never get good used units in these days. *NOTE* This would be a good time to purchase trunk filler boards and package tray if you need them as we can save you money by combining these like shaped items. ...

Yet another incorrect reproduction sold by West Coast Classic Cougar and made by someone who has never even sat in a Cougar... I have no idea where these manufacturers get their color charts! At least you have a base in which to paint over with the correct color. Sorry, we never get good used units in these days. *NOTE* This would be a good time to purchase trunk filler boards and package tray if you need them as we can save you money by combining these like shaped items. ...

Yet another incorrect reproduction sold by West Coast Classic Cougar and made by someone who has never even sat in a Cougar... I have no idea where these manufacturers get their color charts! At least you have a base in which to paint over with the correct color. Sorry, we never get good used units in these days. *NOTE* This would be a good time to purchase trunk filler boards and package tray if you need them as we can save you money by combining these like shaped items. ...

Reproduction single hole front mount center visor bracket for the 1969 and 1970 Mercury Cougar or Ford Mustang. This is a decent reproduction, but not quite as nice as the originals. Reproductions only come in 'paint to suit' black but we have most original colors in used. Replaces Ford Part #: C9AZ-6204132.

Yet another incorrect reproduction sold by West Coast Classic Cougar and made by someone who has never even sat in a Cougar... I have no idea where these manufacturers get their color charts! At least you have a base in which to paint over with the correct color. Sorry, we never get good used units in these days. *NOTE* This would be a good time to purchase trunk filler boards and package tray if you need them as we can save you money by combining these like shaped items. ...

Reproduction BLACK Headliner with Sunroof for the 1969 and 1970 Mercury Cougar. Two piece kit, one piece for the headliner, and a second piece for covering the sunroof panel. On early production cars Ford pulled the cars off the assembly line to sent them to ASC Golde for install. Golde used 3 bows for installing the headliner, whereas in later production Ford used 2 bows when installing them on the assembly line. These headliners are for 2 bows installations. If you have 3 bows, you will...

We have finally found a supplier that produces the correct DARK BLUE perforated headliner for your 1969 or 1970 Cat! Available Colors: White, Black, Dark Red, Medium Blue, Dark Blue, and Saddle. Check out our video below showing how to install one of these bow-type headliners. This was done by a pro, but it's a job you can do yourself with some patience and basic knowledge. ...

These used original plastic filler mount to the passenger side hood extension, and filled the gap between center grille surround (extension) and the side grille. Very rare to find a 1970 Mercury Cougar with both of these intact as the driver side often got broken when someone reached in the recess for the hood release latch. Passenger side only, please note that these normally have a hairline crack in one of the holes, Sold as a single only. Nice reproduction pairs are available for much less...

This portion of the grille bolts in between the eyelid and center grille. This is in grade "B" used condition with minor pitting and scratches.

This portion of the grille bolts in between the eyelid and center grille. This is in grade "B" used condition with minor pitting and scratches.

Complete set of re-chromed grille bars ready to paint and install. Show quality, restored from grille parts with no pits bends or cracks. Like all of our rechromed parts, if you have exceptionally clean cores and have high standards you will want to send your cores in advance. When you do we will do what we call "core matching". If you send in parts with ZERO pits you will get back restored parts that had no pits prior to replating. If you pay the core charge and we send your parts out in...

Sold as a pair, these were a one year only feature that allows you to quickly disconnect the hideaway headlight vacuum hose kit a few inches from the firewall. The fittings are slightly different so as not to mix up the connection by crossing the lines.

Used upper support bracket for the hood latch on any 1970 Mercury Cougar. This 1970 part will work on a 1969. The only difference is the top corner is clipped at an angle on the 1970.Ford part number D0WY-16707-A.

This is the portion of the 1970 grill that ties it all together and mounts it to the core support. This grade B part will have one or more hairline cracks or broken spots throughout, but will not effect its use or performance. Check out this video ...

This is the portion of the 1970 grill that ties it all together and mounts it to the core support. This grade B part will have one or more hairline cracks or broken spots throughout, but will not effect its use or performance.

Show quality chrome that will require that you spray the detail black areas. This purchase requires you send a pit free center in on exchange that has no cracks. A broken upper stud can often be repaired for a minor fee but broken, bent heavily pitted cores cannot be restored. If you are in question as to the merit of your core feel free to email us some pictures prior to sending. Like all of our rechromed parts, if you have exceptionally clean cores and have high standards you will want to...

Good used tank as taken from a Western parts car. Differs from other years only in that the vacuum port is located in a different position. Keep in mind we have units that are not as clean but still hold vacuum for about half the price. Cougar part number D0WY-13A185-A.