All Available Parts - 1970 Mercury Cougar

New wiring pigtail with male bullet connector, and male / female paired connector. Also has rubber grommet that fits a 5/8" inch hole. Looks like 18 gauge wiring. These are remnants from the reproduction Mustang front turn signal lights that we convert to Cougar wiring. Brand new, approximately 13-15 inches in total length. Colors as shown.

Used under dash wiring harness repair ignition switch plug and pigtail for your 1970 Mercury Cougar XR7. This is part of the 14401 main under dash wiring harness.

Used under dash wiring harness repair ignition switch plug and pigtail for your 1970 Mercury Cougar Standard. This is part of the 14401 main under dash wiring harness.

Used under dash wiring harness fuse block / box (with a chip or two) with wire leads for the Mercury Cougar STANDARD. This is part of the 14401 main under dash wiring harness. The difference between Standard and XR7 is that the Standard block has the pink resistance wire. *Note - The fuse blocks will have a small amount of damage or chips on it, in spite of what is shown in the picture.

These same clips are also found on the four rocker switches located in the center of the 1969-1970 XR7 dash pad. Do not bend the "J" shaped tab any further than is necessary to release the plug from the back of the switch as these break easily. There are 16 of these used on a Cougar with power windows in 1969, add the 8 in the dash of the XR7 Cougars and some cars have a total of 24.Replaces Ford part number C9AZ-14530.

Used passenger side (right hand) grade "B" glue in style clear door glass for the Mercury Cougar or Ford Mustang coupe or convertible. This unit will not have the faint green tint like the SUN-X factory tinted glass. Good used door glass with minor vertical scratches due to hardened belt line rubber seal and debris caught within the belt line seal. This glue in style door glass will not work in place of the bolt in versions found in later production models. The glue in style glass was carried...

Early 1970 Mercury Cougar and Ford Mustang coupe / convertible Grade B factory tinted glass for the passenger side door, it will have the faint green tint and be marked SUN-X. Good used door glass with minor vertical scratches due to hardened belt line rubber seal and debris caught within the belt line seal. Glue-in or bonded design, will not fit 1969 models and will not fit 1970 bolt in glass brackets. Bonded or glue-in design 1970 glass was used roughly until January 1970, bolt-in glass...

Early 1970 Mercury Cougar and Ford Mustang coupe / convertible Grade B factory tinted glass for the driver side door, it will have the faint green tint and be marked SUN-X. Good used door glass with minor vertical scratches due to hardened belt line rubber seal and debris caught within the belt line seal. Glue-in or bonded design, will not fit 1969 models and will not fit 1970 bolt in glass brackets. Bonded or glue-in design 1970 glass was used roughly until January 1970, bolt-in glass...

Used passenger side (right hand) grade "B" bolt in style clear door glass for the Mercury Cougar or Ford Mustang coupe or convertible. This unit will not have the faint green tint like the SUN-X factory tinted glass. Good used door glass with minor vertical scratches due to hardened belt line rubber seal and debris caught within the belt line seal. Need a little help identifying some of the markings on your glass? Check out the Guide to Original Date Coded Glass - Mustang, Boss, Shelby and...

Used driver side (left hand) bolt in grade "B" clear door glass for the Mercury Cougar and Ford Mustang coupe or convertible. This unit will not have the faint green tint like the SUN-X factory tinted glass. Good used door glass with minor vertical scratches due to hardened belt line rubber seal and debris caught within the belt line seal. This bolt in style door glass will not work in place of the glue in versions found in early production models. The glue in style glass was carried over from...

1970 Mercury Cougar and Ford Mustang coupe / convertible Grade B factory tinted glass for the passenger side door, it will have the faint green tint and be marked SUN-X. Good used door glass with minor vertical scratches due to hardened belt line rubber seal and debris caught within the belt line seal. Bolted in design, will not fit 1969 models and will not fit 1970 bonded or glued-in style. Bolt in bracket design, 1970 glass, was used midyear, bonded or glued in glass prior. Ford part number...

1970 Mercury Cougar and Ford Mustang coupe / convertible Grade B factory tinted glass for the driver side door, it will have the faint green tint and be marked SUN-X. Good used door glass with minor vertical scratches due to hardened belt line rubber seal and debris caught within the belt line seal. Bolted in design, will not fit 1969 models and will not fit 1970 bonded or glued-in style. Bolt in bracket design, 1970 glass, was used midyear, bonded or glued in glass prior. Ford part number...

Used passenger side (right hand) grade "A" clear bolt in style door glass for the Mercury Cougar or Ford Mustang coupe or convertible. This unit will not have the faint green tint like the SUN-X factory tinted glass. Very good used door glass with no deep scratches (multiple faint scratches and water spots often will be present). Not perfect but the best you could expect to find from a 50 year old plus parts car and will of course be a better fit than repro. This bolt in style door glass will...

Used grade "A" driver side (left hand) clear door glass for the Mercury Cougar and Ford Mustang coupe and convertible. Very good used door glass with no deep scratches (multiple faint scratches and water spots often will be present). Not perfect but the best you could expect to find from a 50 year old plus parts car and will of course be a better fit than repro. Not perfect but the best you could expect to find from a 50 year old plus parts car and will of course be a better fit than repro....

1970 Mercury Cougar and Ford Mustang coupe / convertible Grade A factory tinted glass for the passenger side door, it will have the faint green tint and be marked SUN-X. Very good used door glass with no deep scratches (multiple faint scratches and water spots often will be present). Not perfect but the best you could expect to find from a 50 year old plus parts car and will of course be a better fit than repro. Bolted in design, will not fit 1969 models and will not fit 1970 bonded or...

1970 Mercury Cougar Passenger Side Door Glass - New clear glass. This glass does not have the faint Car-Lite markings in the corner but rather very bold, large SAFETY GLASS in raised letters that cannot be removed without special equipment. Many feel a few minor scratches on an original look better than the raised white lettering found on repros. Keep in mind the fit is slightly better on the used original. Do you have questions about Glue-In vs Bolt-In glass? How about how to properly install...

Reproduction driver side (left hand) bolt in clear door glass for the Mercury Cougar or Ford Mustang. There are three versions of this glass. The clear version is just that, clear with no tint. There is a tinted version that will have a slight green tint to the glass, SUN-X factory tint. There is also a second tinted version that is called smoked and this version has a grey / brown tint to the glass. The clear and the tinted versions are reproductions of original pieces where the smoked...

This glass does not have the faint Car-Lite markings in the corner but rather very bold, large SAFETY GLASS in raised letters that cannot be removed without special equipment. Many feel a few minor scratches on an original look better than the raised white lettering found on repros. Keep in mind the fit is slightly better on the used original. Do you have questions about Glue-In vs Bolt-In glass? How about how to properly install Glue-In glass in your 1969 Cougar or Mustang? Check out our...

Reproduction passenger side (right hand) bolt in clear door glass for the Mercury Cougar or Ford Mustang. There are three versions of this glass. The clear version is just that, clear with no tint. There is a tinted version that will have a slight green tint to the glass, SUN-X factory tint. There is also a second tinted version that is called smoked and this version has a grey / brown tint to the glass. The clear and the tinted versions are reproductions of original pieces where the smoked...

New 10/69 and up to 1970 Mercury Cougar driver side (left hand) tinted (Sun-X) door glass. This glass does not have the faint Car-Lite markings in the corner but rather very bold, large SAFETY GLASS in raised letters that cannot be removed without special equipment. Many feel a few minor scratches on an original look better than the raised white lettering found on repros. Keep in mind the fit is slightly better on the used original. Do you have questions about Glue-In vs Bolt-In glass? How...

Reproduction driver side (left hand) bolt in clear door glass for the Mercury Cougar or Ford Mustang. There are three versions of this glass. The clear version is just that, clear with no tint. There is a tinted version that will have a slight green tint to the glass, SUN-X factory tint. There is also a second tinted version that is called smoked and this version has a grey / brown tint to the glass. The clear and the tinted versions are reproductions of original pieces where the smoked...

1970 Mercury Cougar Passenger Side Glue-In Tinted Door Glass reproduction glass. This glass does not have the faint Car-Lite markings in the corner but rather very bold, large SAFETY GLASS in raised letters that cannot be removed without special equipment. Many feel a few minor scratches on an original look better than the raised white lettering found on repros. Keep in mind the fit is slightly better on the used original. Do you have questions about Glue-In vs Bolt-In glass? How about how to...

Reproduction driver side (left hand) clear glue in door glass for the Mercury Cougar. This glass does not have the faint Car-Lite markings in the corner but rather very bold, large SAFETY GLASS in raised letters that cannot be removed without special equipment. Many feel a few minor scratches on an original look better than the raised white lettering found on repros. Keep in mind the fit is slightly better on the used original. Do you have questions about Glue-In vs Bolt-In glass? How about...

Used drivers side or left hand door window regulator for all 1969 and 1970 Mercury Cougar and Ford Mustangs. *TRIVIA* This style of regulator with the dog legged end on the lift arm, was the service replacement regulator for both 1969 glue in windows and 1970 bolt in windows. Good used regulators that we inspect for operation. We suggest lubricating with suitable grease on all of the moving parts and the actual regulator mechanism during the installation. Comes complete with spring, plastic...

Protects door glass when attaching window channel. Replaces Ford part # C9ZZ-6523258. Do you have questions about Glue-In vs Bolt-In glass? How about how to properly install Glue-In glass in your 1969 Cougar or Mustang? Check out our video below for some great glassy information! 1969 Glue-In Glass: The Comprehensive Repair Guide Video

These inserts snap into your window elevators, four per elevator, eight per door for a total of 16 per car. Often the originals are worn down from lack of lubrication which will cause your door glass to rattle. The originals were more of a clear plastic, these are white in color. These do not fit quite as well as the originals, but work as long as you are OK with the slight play.  For a tighter fit, we recommend that you see the customer reviews of this product for suggestions that...

Most often these do not wear out but instead get lost. These plastic bushings keep the threaded studs from the window elevators from touching the glass as they pass through the holes in your 1970 bolt in door glass. Eight required per car. Replaces Ford part # C9ZZ-6323266 or C9ZZ-6523258-B. *NOTE* These bushings also fit the door glass for the 1969 Mustang Fastback. Do you have questions about Glue-In vs Bolt-In glass? How about how to properly install Glue-In glass in your 1969 Cougar or...

383278-S Nut with spinning or captured washer, sometimes called a swivel nut, for attaching various door window components for 1970-1973 Cougar and Mustang bolt-in door glass. This nut was used to fasten the guides into the 1970 bolt in glass. Additionally this nut was used for attaching the window channel bracket to door and quarter glass on the 1971-73 Cougar and Mustangs.

Window guide or 'elevator'. 1969 through early 1970 Mercury Cougar and Ford Mustang door glass. Two guides per door. Sold individually, will have undamaged excellent threads. Ford master part number C9ZZ-65222A56-A.  *Note will not have original plastic bushing inserts installed. You will need to reuse your originals or purchase new or used. Please see related items. Stamped with C9ZB-65223A00-A, Ford MPC part # C9ZZ-65222A56-A.Same left and right, 4 required per car (2 per...

Bracket or flat piece of channel for the sliding part of the window regulator Right and left interchange. One per door, screws are included. Also used on early bonded design (glue in glass) in 1970. Attaches to the rear bracket with machine screws. Identified by the countersunk holes for the cross point machine screws. Ford part # C9ZZ-6521504-A. Do you have questions about Glue-In vs Bolt-In glass? How about how to properly install Glue-In glass in your 1969 Cougar or Mustang? Check out our...

This is one of the metal tubes that the windows go up and down on, sometimes called an elevator shaft. Right side door only. Application 1969-70 Mercury Cougar and Ford Mustang including Mach 1. Two per door. Front is same as rear. Sometimes marked with a single "R", for right.NOTE: To get the orientation correct on these rods, lay the base of it flat on a table - the rod will lean toward the rear of the door. Ford part # C9ZZ-6521546-A. Do you have questions about Glue-In vs Bolt-In...

This is one of the metal tubes that the windows go up and down on, sometimes called an elevator shaft. Left side door only. Application 1969-70 Mercury Cougar and Ford Mustang including Mach 1. Two per door. Front is same as rear. Sometimes marked with a letter "L", for left. NOTE: To get the orientation correct on these rods, lay the base of it flat on a table - the rod will lean toward the rear of the door. Ford part # C9ZZ-6521547-A. Do you have questions about Glue-In vs Bolt-In glass? How...

Grade B, Rear stop bracket for passenger side door window. Stops the window in the up position. Application passenger side door glass 1969-70 Mercury Cougar and Ford Mustang including Mach 1. One per door. Plate and bolts, not included. Plan on replacing the felt, and most likely the rubber dipped section will be cracked. Please see related listing for plate only or complete stop bracket assembly. Ford part # C9ZZ-65222A54-A. Do you have questions about Glue-In vs Bolt-In glass? How...

Grade B used. Rear door window stop bracket. Stops the window in the up position. Application driver side door glass 1969-70 Mercury Cougar and Ford Mustang including Mach 1. Plan on replacing the felt, the rubber dipped section will also probably be cracked. One per door. Plate and bolts not included. Please see related listing for plate only or complete stop bracket assembly. Ford part # C9ZZ-65222A55-A. Do you have questions about Glue-In vs Bolt-In glass? How about how to...

Window guide or 'elevator'. 1970 Mercury Cougar and Ford Mustang door glass. Two guides per door. Sold individually. Ford master part number D0ZZ-65222A56-A. *Note will not have original plastic bushing inserts installed. Consider reproduction inserts, or plan on re-using your originals. 4 total inserts needed per window guide. Ford part # D0ZB-65223A00-A. *NOTE* This can also be used in conjunction with 69-70 (early) glue in glass. The 69 version is identical except for that 69 was...

Rear bracket for mounting in the 1970 door glass on the passenger side door. 1970 Mercury Cougar and Ford Mustang with bolt in glass. Ford part # D0ZZ-6521430-A. Do you have questions about Glue-In vs Bolt-In glass? How about how to properly install Glue-In glass in your 1969 Cougar or Mustang? Check out our video below for some great glassy information! 1969 Glue-In Glass: The Comprehensive Repair Guide Video ...

Rear bracket for mounting in the 1970 door glass on the driver side door. 1970 Mercury Cougar and Ford Mustang with bolt in glass. Ford part # D0ZZ-6521431-A. Do you have questions about Glue-In vs Bolt-In glass? How about how to properly install Glue-In glass in your 1969 Cougar or Mustang? Check out our video below for some great glassy information! 1969 Glue-In Glass: The Comprehensive Repair Guide Video ...

Bolt in door glass bushing for most 1970 Ford cars with bolted in door windows. This is the white plastic version. Starting in mid-1970 this bushing was made out of black plastic. Except for color they are interchangeable. Ford part # D0ZZ-6523258-A. Do you have questions about Glue-In vs Bolt-In glass? How about how to properly install Glue-In glass in your 1969 Cougar or Mustang? Check out our video below for some great glassy information! 1969 Glue-In Glass: The Comprehensive Repair Guide...

Front bracket for mounting in the 1970 door glass on the passenger side (right hand) door. 1970 Mercury Cougar and Ford Mustang with bolt in glass. Comes with stud that attaches to window regulator. We also have examples in which the stud is missing for a reduced price.  We are looking to find someone to manufacture the T-studs. Both glue-in and bolt-in versions. Please let us know. Ford part # D0ZZ-6523288-A. Do you have questions about Glue-In vs Bolt-In glass? How about how to properly...

Front bracket for mounting in the 1970 door glass on the driver side door. 1970 Mercury Cougar and Ford Mustang with bolt in glass. Comes with stud that attaches to window regulator. We also have examples in which the stud is missing for a reduced price.  We are looking to find someone to manufacture the T-studs. Both glue-in and bolt-in versions. Please let us know. Ford part # D0ZZ-6523288-B. Do you have questions about Glue-In vs Bolt-In glass? How about how to properly install Glue-In...

D1ZZ-6523258-A Black plastic bolt-in door glass bushing. Used on 1970 bolt in door glass and 1971-73 door and quarter glass. White was used in early 1970, and black from 1970-73. There was some overlap in 1970. ...

These inserts snap into your window elevators, four per elevator, eight per door for a total of 16 per car. This is a used part, and they will typically have a very small depression from wear. They can be installed 180° and be good again. Replaces Ford part # C9ZZ-6521496. Reproduction inserts are available.Do you have questions about Glue-In vs Bolt-In glass? How about how to properly install Glue-In glass in your 1969 Cougar or Mustang? Check out our video below for some great glassy...

This is a metal "C" channel that glues to the bottom center of the glued-in door glass on 1969 and early 1970 Mercury Cougar and Ford Mustangs. This channel, helps protect the glass when lowered to the rubber stop at the bottom of the door. Ford part # C9ZZ-214A16-A. *HINT* Use the same professional grade of glass adhesive that you use for bonding the door glass to the two glass mounting brackets. Do you have questions about Glue-In vs Bolt-In glass? How about how to properly install Glue-In...

Bracket or flat piece of channel for the sliding part of the window regulator Right and left interchange. One per door, screws are included. 1970 Mercury Cougar and Ford Mustang bolt in door glass. Attaches to the 1970 rear window bracket with nuts. Ford part # D0ZZ-6521504-A. Do you have questions about Glue-In vs Bolt-In glass? How about how to properly install Glue-In glass in your 1969 Cougar or Mustang? Check out our video below for some great glassy information! 1969 Glue-In Glass: The...

Window stop bolt for 69-70 Cougars. Each stop needs 2 bolts

Grade A, Rear stop bracket for passenger side door window. Stops the window in the up position. Application passenger side door glass 1969-70 Mercury Cougar and Ford Mustang including Mach 1. One per door. Plate and bolts, included. Felt and rubber dipped section will be in good but not great shape. The felt strip really takes a beating. Please see related listing for plate only or B grade bracket without hardware. Ford part # C9ZZ-65222A54-A. Do you have questions about Glue-In vs...

Grade A, Rear stop bracket for driver side door window. Stops the window in the up position. Application passenger side door glass 1969-70 Mercury Cougar and Ford Mustang including Mach 1. One per door. Plate and bolts, included. Felt and rubber dipped section will be in good but not great shape. The felt strip really takes a beating. Please see related listing for plate only or B grade bracket without hardware. Ford part # C9ZZ-65222A55-A. Do you have questions about Glue-In vs Bolt-In glass?...

8-32 screw for attaching the window regulator drive arm slide

Used bolt for installing the door glass window run on any 1969-70 Mercury Cougar or Ford Mustang. This is the lower bolt that goes into the bottom of the door. 1/4-20 threads, hex head but a shallow hex head, Originally installed with a rubber seal, which is not included. 7/16" hex head, these had a Ford part number of 379513-S100. 2 needed per door, 4 per car, sold individually.

Reproduction door glass run. This is the metal tube that the windows go up and down on, sometimes called an elevator shaft. Right side door only. Application 1969-70 Mercury Cougar and Ford Mustang including Mach 1. Two per door. Front is same as rear. Check out our used door glass runs, original Ford and lower priced. NOTE: To get the orientation correct on these rods, lay the base of it flat on a table - the rod will lean toward the rear of the door. Ford part # C9ZZ-6521546-A. Do...

Reproduction door glass run. This is the metal tube that the windows go up and down on, sometimes called an elevator shaft. Left side door only. Application 1969-70 Mercury Cougar and Ford Mustang including Mach 1. Two per door. Front is same as rear.  Check out our used door glass runs, original Ford and lower priced. NOTE: To get the orientation correct on these rods, lay the base of it flat on a table - the rod will lean toward the rear of the door. OK reproduction, but the...

Complete reproduction passenger side bolt in door glass mounting kit for the 1970 Cougar or Mustang. This kit includes both front and rear brackets w/ rubber backing, 2 door run guides w/ inserts, both window stops and all related hardware needed to complete installation.If you want to upgrade your door glass runs to the new reproductions, you can find them here.Door glass not included. ...

These same clips are also found on the four rocker switches located in the center of the 1969-1970 XR7 dash pad. Do not bend the "J" shaped tab any further than is necessary to release the plug from the back of the switch as these break easily. There are 16 of these used on a Cougar with power windows in 1969, add the 8 in the dash of the XR7 Cougars and some cars have a total of 24.Replaces Ford part number C9AZ-14530.

Reproduction power window conversion for your Cougar or Mustang. These kits are easy to install and bolt into the original mounting holes, and use your existing window channels. Once you install the kit, your window crank becomes the switch. Simply lift up on the crank to roll the window up, and press down on the crank to roll the window down. Made from quality materials like 1018 cold rolled steel, Oilite thrust bearings at the pivot points and treated metal for all the gears makes for a high...

Reproduction power window conversion for your Cougar or Mustang. These kits are easy to install and bolt into the original mounting holes, and use your existing window channels. Once you install the kit, your window crank becomes the switch. Simply lift up on the crank to roll the window up, and press down on the crank to roll the window down. Made from quality materials like 1018 cold rolled steel, Oilite thrust bearings at the pivot points and treated metal for all the gears makes for a high...

These clips are found on the power window swtiches of the 69 - 70 Cougar. Each power window switch has one of these clips and one of the J hook clips.6 small clips required per master switch panel, one for each window switch and two per lock out switch. 

Reproduction bolt five piece tinted glass set for the Mercury Cougar coupe. This set does not come with any window trim so save yours for reuse. There are three versions of this glass. The clear version is just that, clear with no tint. There is a tinted version that will have a slight green tint to the glass. There is also a second tinted version that is called smoked and this version has a grey / brown tint to the glass. The clear and the tinted versions are reproductions of original pieces...

Five piece glass set for 1970 Mercury Cougar, clear glass set for bolt in window tracks. Includes glass for both doors, 1970 rear quarter windows, and rear window glass. This is the same as our six piece kit but does not include a new windshield. Verify that you have bolt in style door window glass on those early built 1970 Cougars, glued in glass was carried over for a short period of time. Glass only, hardware and side division seal/chrome not include. This glass does not have the faint...

Complete 5 piece SMOKED bolt in window glass set. Included are the door glass

Reproduction bolt in four piece clear glass set for the 1970 Mercury Cougar convertible. This set does not include any of the window trim so save yours for reuse. There are three versions of this glass. The clear version is just that, clear with no tint. There is a tinted version that will have a slight green tint to the glass. There is also a second tinted version that is called smoked and this version has a grey / brown tint to the glass. The clear and the tinted versions are reproductions...

Reproduction four piece bolt in tinted glass set for the 1970 Mercury Cougar or Ford Mustang convertible. This set does not come with any window trim so save yours for reuse. There are three versions of this glass. The clear version is just that, clear with no tint. There is a tinted version that will have a slight green tint to the glass. There is also a second tinted version that is called smoked and this version has a grey / brown tint to the glass. The clear and the tinted versions are...

Reproduction bolt in four piece smoked glass set for the Mercury Cougar convertible. This set does not include any of the window trim so save yours for reuse. There are three versions of this glass. The clear version is just that, clear with no tint. There is a tinted version that will have a slight green tint to the glass. Then there is this version that is called smoked and this version has a grey / brown tint to the glass. The clear and the tinted versions are reproductions of original...

If you are converting your early 1970 Mercury Cougar or 1969 or early 1970 Cougar Coupe or Convertible from glue in glass to bolt in glass this is the hardware kit you will need. You can reuse your four C9ZB elevators that bolt to these brackets, the only difference between C9ZB and D0ZB is that the C9ZB is fastened by two bolts and the D0ZB has two studs and nuts. Keep in mind that 1969 window regulators will need slight modification to work with this 1970 hardware as the 1970 regulator does...

Locking nut for attaching the door window regulator to the window channel bracket on any 1969-70 Mercury Cougar or Ford Mustang. While we do not sell the T-bolts for attaching to the regulator (T-bolt Ford Part # C8SZ-6523274-A), we do have a retainer to keep it in the front channel bracket. Find it here. This is not an exact replica of the t-bolt lock nut, but is a functional replacement part. Replaced Ford part #: 34975-S ...

These inserts snap into your window elevators, four per elevator, eight per door for a total of 16 per car. Often the originals are worn down from lack of lubrication which will cause your door glass to rattle. The originals were more of a clear plastic, these are white in color. These do not fit quite as well as the originals, but work as long as you are OK with the slight play.  For a tighter fit, we recommend that you see the customer reviews of this product for suggestions that...

New bolt for installing the door glass window run on any 1969-70 Mercury Cougar or Ford Mustang. This is the lower bolt that goes into the bottom of the door. 1/4-20 threads, hex head but a shallow hex head, Originally installed with a rubber seal, which is not included. 7/16" hex head, these had a Ford part number of 379513-S100. 2 needed per door, 4 per car, sold individually. Black silicone is a good substitute for the seal.

383278-S 1/4-20 Nut with spinning or captured washer, sometimes called a swivel nut, for attaching various door window components for 1970-1973 Cougar and Mustang bolt-in door glass. This nut was used to fasten the guides into the 1970 bolt in glass. Additionally this nut was used for attaching the window channel bracket to door and quarter glass on the 1971-73 Cougar and Mustangs. This is a new or reproduction part from AMK.

This gear was used on Cougars starting in 1969 and then Mustang in 1971. Fits pretty much every (common) Ford power window motor except for the unique "pancake" style motors found with the 1/4 windows on the Cougar and Mustang. Includes metal plate as shown. Replaces Ford part # D0AZ-62234A24. Do you have questions about Glue-In vs Bolt-In glass? How about how to properly install Glue-In glass in your 1969 Cougar or Mustang? Check out our video below for some great glassy information! 1969...

These vinyl coated clips hold the weatherstrip and guide the window when rolling up. Used clips usually are rusted and the vinyl portion is peeling. Sold individually and four are required per car. Replaces Ford part #: C9ZZ-6522204. Do you have questions about Glue-In vs Bolt-In glass? How about how to properly install Glue-In glass in your 1969 Cougar or Mustang? Check out our video below for some great glassy information! 1969 Glue-In Glass: The Comprehensive Repair Guide Video ...

3M brand two part channel bonding adhesive for gluing in the Mercury Cougar or Ford Mustang door side glass and rear quarter glass. This is the best product on the market for re-gluing those troublesome 1969 side windows. We use this product for our own cars here at WCCC and have found an applicator that works great. If you just need an applicator to do just your car, we have a 60 day loaner you can use right here. However, if you are doing multiple cars or other parts, you may want to...

Plastic covers for the seat belt shoulder straps on the 1970 Mercury Cougar and Ford Mustang. Sold as a Pair. Replaces Ford Part #: D0ZB-6560234, D0ZB-6560235.

These are great for your back seat belts or convertibles that did not use retractors in the front. They are an exact copy of the originals that were available as a dealer option from 1964 and up. Sold Individually. Made in U.S.A. Replaces Ford Part #: C4AZ-65611A06. Customer feedback: I just wanted to tell that your delivery has arrived today. Thanks a lot! Never ever ordered something (not even here in Germany) and got it that fast. Awesome! My next orders will go to your place and I will...

Includes one lap belt, the mounting bolts and washers.sold individually

Great looking replacement style seat belts. All feature a mid sixties period look which includes a chrome buckle. Available in a variety of colors. Sold individually

Great looking replacement style seat belt. All feature a mid sixties period look which includes a chrome buckle. Available in a variety of colors. These are great lap belts for convertible cars that don't use retractors. We suggest using seat belt anchor bolts for an easy installation of these aftermarket lap seat belts. This kit does come with installation hardware, but the threads on the bolt are coarse, and will not bolt into your original threaded anchor points. sold individually ...

Great looking replacement style seat belts. All feature a mid sixties period look which includes a chrome buckle. Available in a variety of colorssold individually

Great looking replacement style seat belts. All feature a mid sixties period look which includes a chrome buckle. Available in a variety of colors.sold individually

Great looking replacement style seat belts. All feature a mid sixties period look which includes a chrome buckle. Available in a variety of colors.sold individually

Great looking replacement style seat belts. All feature a mid sixties period look which includes a chrome buckle. Available in a variety of colors.sold individually

Great looking replacement style seat belts. All feature a mid sixties period look which includes a chrome buckle. Available in a variety of colors.sold individually

Great looking replacement style seat belts. All feature a mid sixties period look which includes a chrome buckle. Available in a variety of colors.sold individually

These are era-correct looking seat belts at an affordable price.  These are not Concours reproductions, but have the correct vintage look used by Ford on multiple cars in the Mid to Late 1960's. Starburst Medallion used on the buckle is an exact copy of originals.Sold individually Includes: 1 Complete non-retracting seat belt (includes both male and female side)2 Bolts, nuts, and lock washers

These are original looking seat belts at affordable prices. These are not Concours reproductions, but have the correct vintage look used by Ford on several cars in the Mid to Late 1960's. Starburst Medallion used on the buckle is an exact copy of originals. Hardware included!sold individually

These are original looking seat belts at affordable prices. These are not Concours reproductions, but have the correct vintage look used by Ford on several cars in the Mid to Late 1960's. Starburst Medallion used on the buckle is an exact copy of originals. Hardware included!sold individually

These are original looking seat belts at affordable prices. These are not Concours reproductions, but have the correct vintage look used by Ford on several cars in the Mid to Late 1960's. Starburst Medallion used on the buckle is an exact copy of originals. Hardware included!sold individually

These are original looking seat belts at affordable prices. These are not Concours reproductions, but have the correct vintage look used by Ford on several cars in the Mid to Late 1960's. Starburst Medallion used on the buckle is an exact copy of originals. Hardware included!Sold individually

These are original looking seat belts at affordable prices. These are not Concours reproductions, but have the correct vintage look used by Ford on several cars in the Mid to Late 1960's. Starburst Medallion used on the buckle is an exact copy of originals. Hardware included!sold individually

These are original looking seat belts at affordable prices. These are not Concours reproductions, but have the correct vintage look used by Ford on several cars in the Mid to Late 1960's. Starburst Medallion used on the buckle is an exact copy of originals. Hardware included! sold individually

This is an original looking seat belt at an affordable price. These are not Concours reproductions, but have the correct vintage look used by Ford on several cars in the Mid to Late 1960's. Starburst Medallion used on the buckle is an exact copy of originals. Hardware included! SOLD INDIVIDUALLY

These are original looking seat belts at affordable prices. These are not Concours reproductions, but have the correct vintage look used by Ford on several cars in the Mid to Late 1960's. Starburst Medallion used on the buckle is an exact copy of originals. Hardware included!Sold individually

Used bolts, and usually new washers. Coupe kit comes with 4 - "A" bolts, 4 "B" bolts, and 2 "D" bolts, 12 new washers. Kit fits all 1970-73 Mercury Cougar and Ford Mustang coupes. Coupes or hard tops will have shoulder belt hardware. We will make sure these original seat belt bolts are damage free and rust free. The gold finish will be degraded.  There were minor and major changes almost every year. We also have hundreds of used belts and belt sets that we cannot possibly list...

This is a fully functional grade "B" retractor that will have a small crack in the plastic "holster" and may show very slight pitting on chrome. Driver quality, ready to plug and play. NOTE: Front retractors are same for left and right, and are good for all 67-73 Cougar AND Mustang applications. Also, the difference between the standard and deluxe versions are the end of the buckle, the standard is rounded and the deluxe is ridged. Check out this video ...

This is the very best we can offer. No cracks in the plastic holster, good color and no fraying on the webbing. NOTE: Front retractors are not side specific for all years 67-73, and are good for Cougar AND Mustang applications.Also, the difference between the standard and deluxe versions are the end of the buckle, the standard is rounded and the deluxe is ridged. Check out our video "All about seat belts" below. ...

This is the plastic center piece you press down to release your seat belt on the 68 - 72 seat belts. It comes unbroken and without cracks. This button piece has original starburst decal, which will be faded and need replacing. Find the replacement decals here. Spring is included.

Used on the majority of Fords, this assembly can easily be removed without cutting or un-stitching the webbing. No rust, grade "A" show quality chrome, originally came stamped ROBBINS - JR - 7600 or HAMILL H-000. If you have a preference as to which version you would like just let us know in the memo box at checkout. Check out our video "All about seat belts" below. ...

This is the complete one piece seat belt buckle cover which comes with the face plate (with the round cutout for the push button) and the bezel all in one. This version is handy when you don't want to deal with multiple parts (as is the case with the separate face plate and bezel version). Simply remove your old cracked or broken cover, replace the metal spacer, and pop this cover into place and you're ready to go! You can use your existing spacer, or if you're missing one, you can find it...

This face plate fits inside the buckle bezel on the two piece type seat belt buckle cover. These plastic face plates are going to be free from cracks or breaks, and will still have some good texture to them. Keep in mind that although we don't reproduce the sponge dampener that's glued on the inside, most of these plates are going to be missing that piece, because after all......that dampener has been in there for up to 46 years! (this doesn't effect its useability). You can use your existing...

Used seat belt buckle bezel for the Mercury Cougar, Ford Mustang, or Ford Torino. This is the outer portion of the two piece seat belt buckle cover. This is a good replacement part if you want to keep your car original. These bezels will be free of cracks and breaks. Please specify which color you're looking for when ordering. Keep in mind that there are only a handful of colored buckles available, so we'll do our best to get you the color you need. Check out our video "All about seat belts"...

This is a general listing for anything and everything seat belt related. We can't go through and list every single seat belt part we have here, but chances are, we have what you need. If you're looking for used belts, all you have to do is call our seat belt guy (his name is Junior, at extension 209) and he'll go out in the warehouse and put together a set to match your needs and price range. We have everything from dirty old faded belts with minor rust on the chrome, to super nice, clean,...

This is the plastic center piece you press down to release your seat belt on the 68 - 72 seat belts. It comes unbroken and without cracks. This button piece has original decal with starburst design. Spring is included. Check out our video "All about seat belts" below.