All Available Parts - 1970 Mercury Cougar

Leaf Springs shipping time is 12 weeks. All of our springs are intended to return the car to factory height. Because of that, installing new springs will almost always increase the height of the rear of the car, as the factory leafs sag over the years. The competition springs will sit slightly lower than standard springs, somewhere between 1/2" and 1" lower. The competition springs cause the car to have a slightly lower the center of gravity and the competition springs are a stiffer spring, so...

Leaf Springs shipping time is 12 weeks. All of our springs are intended to return the car to factory height. Because of that, installing new springs will almost always increase the height of the rear of the car, as the factory leafs sag over the years. The competition springs will sit slightly lower than standard springs, somewhere between 1/2" and 1" lower. The competition springs cause the car to have a slightly lower the center of gravity and the competition springs are a stiffer spring, so...

Leaf Springs shipping time is 12 weeks. All of our springs are intended to return the car to factory height. Because of that, installing new springs will almost always increase the height of the rear of the car, as the factory leafs sag over the years. The competition springs will sit slightly lower than standard springs, somewhere between 1/2" and 1" lower. The competition springs cause the car to have a slightly lower the center of gravity and the competition springs are a stiffer spring, so...

Leaf Springs shipping time is 12 weeks. All of our springs are intended to return the car to factory height. Because of that, installing new springs will almost always increase the height of the rear of the car, as the factory leafs sag over the years. The competition springs will sit slightly lower than standard springs, somewhere between 1/2" and 1" lower. The competition springs cause the car to have a slightly lower the center of gravity and the competition springs are a stiffer spring, so...

Leaf Springs shipping time is 12 weeks. All of our springs are intended to return the car to factory height. Because of that, installing new springs will almost always increase the height of the rear of the car, as the factory leafs sag over the years. The competition springs will sit slightly lower than standard springs, somewhere between 1/2" and 1" lower. The competition springs cause the car to have a slightly lower the center of gravity and the competition springs are a stiffer spring, so...

Leaf Springs shipping time is 12 weeks. All of our springs are intended to return the car to factory height. Because of that, installing new springs will almost always increase the height of the rear of the car, as the factory leafs sag over the years. The competition springs will sit slightly lower than standard springs, somewhere between 1/2" and 1" lower. The competition springs cause the car to have a slightly lower the center of gravity and the competition springs are a stiffer spring, so...

Leaf Springs shipping time is 12 weeks. All of our springs are intended to return the car to factory height. Because of that, installing new springs will almost always increase the height of the rear of the car, as the factory leafs sag over the years. The competition springs will sit slightly lower than standard springs, somewhere between 1/2" and 1" lower. The competition springs cause the car to have a slightly lower the center of gravity and the competition springs are a stiffer spring, so...

Leaf Springs shipping time is 12 weeks. All of our springs are intended to return the car to factory height. Because of that, installing new springs will almost always increase the height of the rear of the car, as the factory leafs sag over the years. The competition springs will sit slightly lower than standard springs, somewhere between 1/2" and 1" lower. The competition springs cause the car to have a slightly lower the center of gravity and the competition springs are a stiffer spring, so...

Leaf Springs shipping time is 12 weeks. All of our springs are intended to return the car to factory height. Because of that, installing new springs will almost always increase the height of the rear of the car, as the factory leafs sag over the years. The competition springs will sit slightly lower than standard springs, somewhere between 1/2" and 1" lower. The competition springs cause the car to have a slightly lower the center of gravity and the competition springs are a stiffer spring, so...

Leaf Springs shipping time is 12 weeks. All of our springs are intended to return the car to factory height. Because of that, installing new springs will almost always increase the height of the rear of the car, as the factory leafs sag over the years. The competition springs will sit slightly lower than standard springs, somewhere between 1/2" and 1" lower. The competition springs cause the car to have a slightly lower the center of gravity and the competition springs are a stiffer spring, so...

Leaf Springs shipping time is 12 weeks. All of our springs are intended to return the car to factory height. Because of that, installing new springs will almost always increase the height of the rear of the car, as the factory leafs sag over the years. The competition springs will sit slightly lower than standard springs, somewhere between 1/2" and 1" lower. The competition springs cause the car to have a slightly lower the center of gravity and the competition springs are a stiffer spring, so...

Leaf Springs shipping time is 12 weeks. All of our springs are intended to return the car to factory height. Because of that, installing new springs will almost always increase the height of the rear of the car, as the factory leafs sag over the years. The competition springs will sit slightly lower than standard springs, somewhere between 1/2" and 1" lower. The competition springs cause the car to have a slightly lower the center of gravity and the competition springs are a stiffer spring, so...

Leaf Springs shipping time is 12 weeks. All of our springs are intended to return the car to factory height. Because of that, installing new springs will almost always increase the height of the rear of the car, as the factory leafs sag over the years. The competition springs will sit slightly lower than standard springs, somewhere between 1/2" and 1" lower. The competition springs cause the car to have a slightly lower the center of gravity and the competition springs are a stiffer spring, so...

Leaf Springs shipping time is 12 weeks. All of our springs are intended to return the car to factory height. Because of that, installing new springs will almost always increase the height of the rear of the car, as the factory leafs sag over the years. The competition springs will sit slightly lower than standard springs, somewhere between 1/2" and 1" lower. The competition springs cause the car to have a slightly lower the center of gravity and the competition springs are a stiffer spring, so...

Leaf Springs shipping time is 12 weeks. All of our springs are intended to return the car to factory height. Because of that, installing new springs will almost always increase the height of the rear of the car, as the factory leafs sag over the years. The competition springs will sit slightly lower than standard springs, somewhere between 1/2" and 1" lower. The competition springs cause the car to have a slightly lower the center of gravity and the competition springs are a stiffer spring, so...

Leaf Springs shipping time is 12 weeks. All of our springs are intended to return the car to factory height. Because of that, installing new springs will almost always increase the height of the rear of the car, as the factory leafs sag over the years. The competition springs will sit slightly lower than standard springs, somewhere between 1/2" and 1" lower. The competition springs cause the car to have a slightly lower the center of gravity and the competition springs are a stiffer spring, so...

Includes 2 hex head Screw & Washer Assembly aka "SEMS" bolts for the throttle cable bracket on the 1970 Cougar or Mustang equipped with the 428 Cobra Jet.

This 2-1/4 rear segment exhaust system is manufactured right here in the good old USA from an original 1969 R code Cougar. This direct replacement system includes: 2 intermediate pipes, 2 mufflers, and a right and left tail pipe. The system is constructed from 2-1/4 inch aluminized piping and features blue printed bends with everything being replicated as close as possible to the original. The mufflers in the system have the hanging tabs attached so that they will accept original muffler...

This direct replacement features a larger than stock diameter of 2-1/2 inches for increased performance. This is the H pipe only and is for any 1970 Mercury Cougar or Ford Mustang with stock cast iron exhaust manifolds without the spacer on the passenger side. These units are manufactured right here in the good old USA from 2-1/2 inch aluminized pipes and made from an original 1970 Cougar and Mustang with the 428CJ engine. We also sell this H pipe in a 2-1/4 inch diameter and have OEM style...

This direct replacement is the 2-1/4 inch H pipe only and is for any 1970 Mercury Cougar or Ford Mustang with stock cast iron exhaust manifolds without the passenger side spacer. These units are manufactured right here in the good old USA from 2-1/4 inch aluminized pipes and made from an original 1970 Cougar and Mustang with the 428CJ engine. We also sell this H pipe in a 2-1/2 inch diameter and have OEM style dual exhaust systems that include the H pipe, mufflers, and tail pipes.*NOTE* Please...

This direct replacement is the 2-1/4 inch H pipe only, and is for any 1970 Mercury Cougar or Ford Mustang with stock 2V cast iron exhaust manifolds. These units are manufactured right here in the good old USA from 2-1/4 inch aluminized pipes and custom made for dual exhaust on any 1970 Cougar and Mustang with the 2 barrel H code 351C engine. We also sell OEM style dual exhaust systems that include the H pipe, mufflers, and tail pipes.*NOTE* Will not fit 351W, 1970 351C-4V, or 1971-73 Cleveland...

This direct replacement is the 2-1/4 inch H pipe only and is for any 1970 Mercury Cougar or Ford Mustang with stock 4V cast iron exhaust manifolds. These units are manufactured right here in the good old USA from 2-1/4 inch aluminized pipes and made from an original 1970 Cougar and Mustang with the 4 barrel M code 351C engine. We also sell OEM style dual exhaust systems that include the H pipe, mufflers, and tail pipes.*NOTE* Will not fit 351 Windsor, 1970 351C-2V, or 1971-73 Cleveland...

This direct replacement is the 2-1/2 inch H pipe only and is for any 1969-70 Mercury Cougar or Ford Mustang with stock cast iron exhaust manifolds. These units are manufactured right here in the good old USA from 2-1/2 inch aluminized pipes and made from an original 1970 Cougar Eliminator and Boss Mustang  with the G code Boss 302 engine. We also sell OEM style dual exhaust systems that include the H pipe, mufflers, and tail pipes.*NOTE* Please allow 2 - 3 weeks for delivery. ...

This direct replacement is the 2 inch Y pipe only with 2-1/4 intermediate pipe outlets and is for any 1969-70 Mercury Cougar or Ford Mustang equipped with the 351W engine with stock cast iron exhaust manifolds. These units are manufactured right here in the good old USA from 2 inch aluminized pipes and made from an original 1971 Cougar and Mustang with the 351W 2V engine. We also sell OEM style dual exhaust systems that include the H pipe, mufflers, and tail pipes.*NOTE* Will not fit 351...

This direct replacement is the 2-1/4 inch Y pipe only and is for any 1970 Mercury Cougar or Ford Mustang with stock cast iron exhaust manifolds. These units are manufactured right here in the good old USA from 2-1/4 inch aluminized pipes and made from an original 1970 Cougar and Mustang  with the 351C 2V engine. We also sell OEM style dual exhaust systems that include the H pipe, mufflers, and tail pipes.*NOTE* Will not fit 351-4V Cleveland engines, or 1971-73 351C engines. Please allow 2...

This 2-1/4 inch dual exhaust system is manufactured right here in the good old USA from an original 1969 R code Cougar. This direct replacement system includes: 1 H pipe, 2 intermediate pipes, 2 mufflers, and a right and left tail pipe. The system is constructed from 2-1/4 inch aluminized piping and features blue printed bends with everything being replicated as close as possible to the original. The mufflers in the system have the hanging tabs attached so that they will accept original...

This 2-1/4 inch dual exhaust system is manufactured right here in the good old USA from an original 1970 Q code Cougar. This direct replacement system includes: 1 H pipe, 2 intermediate pipes, 2 mufflers, and a right and left tail pipe. The system is constructed from 2-1/4 inch aluminized piping and features blue printed bends with everything being replicated as close as possible to the original. The mufflers in the system have the hanging tabs attached so that they will accept original...

This 2-1/4 inch dual exhaust system is manufactured right here in the good old USA from original 1969-70 G code Cougar Eliminators. This direct replacement system includes: 1 H pipe at 2-1/2 inches, 2 intermediate pipes at 2-1/4 inches, 2 mufflers at 2-1/4 inches, and a right and left tail pipe each at 2-1/4 inches. The system is constructed from 2-1/2 and 2-1/4 inch aluminized piping and features blue printed bends with everything being replicated as close as possible to the original. The...

This 2-1/4 inch dual exhaust system is manufactured right here in the good old USA from an original 1970 M code 351C 4V equipped Cougar. This direct replacement system includes: 1 H pipe, 2 intermediate pipes, 2 mufflers, and a right and left tail pipe. The system is constructed from 2-1/4 inch aluminized piping and features blue printed bends with everything being replicated as close as possible to the original. The mufflers in the system have the hanging tabs attached so that they will...

This reproduction 2 1/4" Tri-Y H pipe to be used with the Patriot style headers on your 1970 Cougar or Mustang.

This reproduction 2 1/4" Tri-Y H pipe to be used with the Scott Drake style headers on your 1970 Cougar or Mustang.

This 2-1/4 inch dual exhaust system is manufactured right here in the good old USA from an original 1970 M code 351C 2V equipped Cougar. This direct replacement system includes: 1 H pipe, 2 intermediate pipes, 2 mufflers, and a right and left tail pipe. The system is constructed from 2-1/4 inch aluminized piping and features blue printed bends with everything being replicated as close as possible to the original. The mufflers in the system have the hanging tabs attached so that they will...

Now in grey with no zipper, our comfy WCCC hoodie features bold new walking cat graphics on front and back. Perfect for staying warm in the garage, or out and about with your Cougar! This sweatshirt is made with soft, mid weight fleece and generous fit for comfort. Features a jersey lined hood, heavy gauge drawcord with metal eyelets and 1x1 ribbing at cuffs and waistband. 8.5 oz fleece80% cotton 20% polyester blend100% cotton 20 singles face yarnSplit stitch double needle sewing on all...

Now in black with no zipper, our comfy WCCC hoodie features bold new walking cat graphics on front and back. Perfect for staying warm in the garage, or out and about with your Cougar! This sweatshirt is made with soft, mid weight fleece and generous fit for comfort. Features a jersey lined hood, heavy gauge drawcord with metal eyelets and 1x1 ribbing at cuffs and waistband. 8.5 oz fleece80% cotton 20% polyester blend100% cotton 20 singles face yarnSplit stitch double needle sewing on all...

Right side axle, 28 spline 31-1/8 inch length. For both 8 inch and 9 inch rear ends. Ships with used bearing, bearing retainer plate, and 5 pressed in wheel studs. *Note Boss 302 and 428 CJ equipped Cougars came with heavy duty 31 splined axles.

Left side axle, 28 spline 27-1/16 inch length. For both 8 inch and 9 inch rear ends. Ships with used bearing, bearing retainer plate, and 5 pressed in wheel studs.*Note Boss 302 and 428 CJ equipped Cougars came with heavy duty 31 splined axles.

NOTE! When we ship a rear end, we will remove the third member and ship it in a separate box. Some assembly will be required. D0ZZ-4010-Assy 1970 9 Inch Rear End Housing Complete - Used Housing overall width - 54-1/4 inches flange to flange. Spring perches are 43 inches apart on center. Rear axle assembly - Housing, Axles, brake backing plates, and third member. 1970 housings are different from 1969 9 inch housings. 1970 housings have a separate vent tube, 1969 vent tubes are used to hold...

Bare housing with proper axle pad spacing, vent location, and brake line attaching. For all 1970 Cougars. Over-sized shipping length. Housing overall width - 54-1/4 inches flange to flange. Spring perches are 43 inches apart on center. Axles needed: Passenger side - 31-1/8 inches long, Driver side 27 inches long.

The 69-73 looks the same as the earlier version once installed but the casting number will read C3AA-4906-C on the early unit and C9OA-4906-A on the 1969-73 version. We have found a few rubber bumpers marked D3Z... very few. See other listing for that one..

9 inch rear axle snubber for all 1968-73 Mercury Cougar and Ford Mustang. Will work on 1967 9" differential but has slightly different angles as seen by our pictures. Bare bracket, rubber snubber sold separately.

Since we always claim to have parts nobody else does... This welds to the bottom side of the car just above the differential. When the rear suspension bottoms out, this is the plate the rubber snubber / bumper (mounted on the front on top of the dif.) makes contact with.

Also called a pumpkin, 2.75:1 open ratio. Check your door tag under "Axle". 1968 code 1 1969-73 code 2

Mounts over rear axle ends into the body/frame, two required per car, this is the more pointed Christmas tree shaped version.Ford part # C6AZ-4730

D0OZ-4204-9A300 1968-1973 9 Inch Third Member - Used Also called a pumpkin, 3.00:1 open ratio. These 3rd members will have the fill plug. Check your door tag under "Axle".

#373820-S Copper washer for attaching the 8 inch or 9 inch third members to the axle housings. Steel washers will leak, made from copper which is a soft metal and seals under the attaching nuts. Copper washers like the OEM Ford installed washers. Takes 10 washers total for both 8 and 9 inch rear ends. *Tip - It is a good idea to inspect or replace your old washers, many times they have tool marks from the housing or nuts that cause small troublesome leaks.

This gas Shock Absorber improves handling without sacrificing ride comfort. A very good choice for the daily driver wanting a smooth ride with the response of a gas shock.  These shocks are sold individually and are designed more specifically to work with Cougars as opposed to Mustang. Manufacturer Specs: ExtendedCompressedStrokeCoverInternal StopExternal Stop19.3711.308.07X-- ...

These shocks are the as close to original specs as possible for the Mercury Cougar. This is the performance shock for those looking for firmer ride. The KYB Gas-a-Just shocks use higher gas pressure to keep your tires glued to the road. The KYB Gas-a-Just shocks' velocity-sensitive valving system adjusts quickly to changing road conditions for maximum comfort in any situation. Their mono tube configuration eliminates aeration and foaming, their micro-smooth, hard-chromed pistons extend their...

Sold individually, two required per car. Replaces Ford part # C3DZ-4730.

This is a good used core piece of trim that is ready to be restored or bolted onto that less than perfect driver.

Correctly restored, anodized aluminum trim. Requires painting in the recessed areas. New hood trim attaching clips with nuts available here.   Fits: 1970 Mercury Cougar

We do what we have dubbed as "core matching". The better quality cores you send us, the better product you will get in exchange. If you would prefer your original cores be restored just mention it in a note when you send in payment with your restorable parts. It is also a good idea to scratch your initials on the back side. New eyebrow attaching clips with nuts available here.  

Used 20 amp circuit breaker for either 69 - 70 or 71-73 Cougars.Mounted on the Starter solenoid in 69-70 cougars for convertible tops or power windows, and also on 71-73 Standard Cougars for convertible tops, power windows, heated back light, power seats or seat back release.On the 71-73 XR7 the circuit breaker was mounted next to the starter solenoid on a junction block. Different wire diagrams, owner / shop manuals list this circuit breaker in both locations, possibly due to multiple...

Concours Throttle Return Spring for the 390 / 428CJ / 428SCJ Manufactured after 4-9-69

Passenger side shock mounting plate for any 1967-73 Mercury Cougar with any V-8 engines. A passenger side and **driver side bracket are needed for most applications.  **Excludes 1969 - 1970 Boss 302 & 428 Cobra Jet 4 speed Cougars. Additionally 1972 - 1973 351CJ (Q code engines - all transmissions) which all came with staggered rear shocks, which was part of those years Competition Handling Package. These applications had staggered rear shock plates. Order two C9OZ-5796-C right...

Limited slip 8 inch Ford third member rebuilt with all new parts. Factory new 4 pinion Trac-Loc unit, new Motive ring and pinion gears, new Timkin bearings, new crush sleeve, new bolts, and new seal. Rebuilt using 1967 and newer two rib style case, with oil fill plug, and standard 1310 yoke. There are various ring and pinion (gear) ratios and axle splines available, if you are unsure of what you need it is best to call (503) 463-1130 for your order. This is a drop ship item. *Note - New...

Limited slip 8 inch Ford third member rebuilt with all new parts. Factory new Eaton True-Trac 8 pinion clutchless traction locking unit, Richmond ring and pinion gear, Timkin bearings, crush sleeve, bolts, and seal. Rebuilt using 1967 and newer two rib style case, with oil fill plug, and standard 1310 yoke. Ships with direction sheet and bottle of Ford Motorcraft friction modifier additive for the rear end gear oil. For use with 28 splined axles, but can be custom...

Limited slip 9 inch Ford third member rebuilt with all new or reconditioned parts. Rebuilt 4 pinion Trac-Loc unit, with new clutches, steels, Richmond ring and pinion gears, Timkin bearings, crush sleeve, bolts, and seal. Rebuilt using standard 9 inch cases with oil fill plug. Ships with direction sheet and bottle of Ford Motorcraft friction modifier additive for the rear end gear oil. For 28 or 31 splined axles. This unit was used in Cougars and Mustangs, but also any other Fords...

Limited slip 9 inch Ford third member rebuilt with all new parts. New 4 pinion Trac-Loc unit, Richmond ring and pinion gears, Timkin bearings, crush sleeve, bolts, and new a seal. Rebuilt using the standard 9 inch case, with oil fill plug. Ships with direction sheet and bottle of Ford Motorcraft friction modifier additive for the rear end gear oil. For 28 or 31 splined axles. This unit is for 1967-73 Cougars and Mustangs, but it works for any other Mercurys or Fords with a 9 inch...

Limited slip 9 inch Ford third member rebuilt with all new parts. New Eaton True-Trac 8 pinion clutchless traction locking unit, Richmond ring and pinion gear, Timkin bearings, crush sleeve, bolts, and seal. Rebuilt using 1967-1973 standard 9 inch case with oil fill plug. For 28 or 31 splined axles. This unit is for 1967-73 Cougars and Mustangs, but can be used on any other Ford or Mercury with a 9 inch drop out center section. Because of all the various ring and pinion...

Limited slip nodular 9 inch Ford third member rebuilt with all new parts. New 4 pinion Trac-Loc unit, Richmond ring and pinion gears, Timkin bearings, selective size sleeve, bolts, and seal. Rebuilt using a nodular 9 inch case with oil fill plug. Ships with direction sheet and bottle of Ford Motorcraft friction modifier additive for the rear end gear oil. For 28 or 31 splined axles. This unit is for 1967-73 Cougars and Mustangs, but it can also be used for any other Ford or...

Limited slip nodular 9 inch Ford third member rebuilt with all new parts. New Eaton True-Trac 8 pinion clutchless traction locking unit, Richmond ring and pinion gear, Timkin bearings, selective size sleeve, bolts, and seal. Rebuilt using a 1967-1973 nodular 9 inch case with oil fill plug. For 28 or 31 splined axles. This unit is for 1967-73 Cougars and Mustangs, but can be used in any other Ford or Mercury with a 9 inch drop out center section. Because of all the...

Limited slip, nodular 9 inch Ford third member rebuilt with all new or reconditioned parts. Used modern design Detroit Locker unit, new Richmond ring and pinion gear, new Timkin bearings, new selective size sleeve, new bolts, and new seal. Rebuilt using 1967-1973 nodular 9 inch cases with oil fill plug, for 28 or 31 splined axles. This unit was used in 1967-73 Cougars and Mustangs, but it also came in any other Fords or Mercurys with a 9 inch drop out center section....

Most 1969 and 1970 351 engines 3 or 4 speed manual transmission. Shaft diameter 2-3/4 inches. Length 53-1/4 inches, measured on U-joint centers. Used and 'as balanced' from the factory. *NOTE* 1970 M-code - 351C-4V engines came from the factory with 3 inch drive shafts. Ask about slip yokes. Shipping is oversized due to length.

Most 1969 and 1970 351 engines with FMX transmissions. Shaft diameter 3 inches. Length 53-9/16 inches, measured on U-joint centers. Used and 'as balanced' from the factory.*NOTE* Some 1970 M code 351C-4V engines came from the factory with 3-1/2 inch drive shafts. We think it may have been those with competition handling packages. Does anyone know for sure?Ask about slip yokes. Shipping is oversized due to length.

Nuts and washers for attaching the rear differential carrier or pumpkin or third member to the rear axle housing. Correct for all 1969-73 Mercury Cougar and 1969-73 Ford Mustang. 8 inch or 9 inch third members, all the same.

Leaf spring front bolts for any 1969-70 Mercury Cougar or Ford Mustang. AMK F-251, About 4-3/8 inches long. 4 total pieces, 2 bolts, 2 nuts.

Passenger side chassis bumper bracket for the rear axle. Passenger side as removed from a 1967-73 Mercury Cougar. Good condition bracket, road tested, but not salt road tested. Ships as shown, cut with generous margins around the original bracket.

Driver side chassis bumper bracket for the rear axle. Passenger side as removed from a 1967-73 Mercury Cougar. Good condition bracket, road tested, but not salt road tested. Ships as shown, cut with generous margins around the original bracket.

Ford original eye let bushing 100% correct for the 67-69 Cougar without competition handling, but will fit on any 67-73 cat including those with competition handling. Ford Part #: C4DZ-5781-C.

Reproduction anti-squeak pad for the leaf springs found on the Mercury Cougar or Ford Mustang. This little unit goes between each individual leaf spring and prevents metal to metal contact. These are sold individually and eight are required per car. Our reproduction leaf springs come with this pad pre-installed. Replaces Ford part # C0AA-5586.

This is the bushing that Ford lists as the REAR stabilizer end link bushing, but it works for both front and rear. Smaller image shows a comparison of the NOS(Left) and Repro (right). SOLD INDIVIDUALLY. Replaces Ford Part #: KC-55490-A.

This is the bushing that Ford lists as the REAR stabilizer end link bushing, but it works for both front and rear. Smaller image shows a comparison of the NOS(Left) and Repro (right). SOLD AS SET OF 8. Replaces Ford Part #: KC-55490-A.

Correct leaf spring eye bushing bolts for the 1968 - 1973 Mercury Cougar. 5" in length. Set includes 2 bolts and 2 nuts. Replaces Ford Part #: C7ZZ-5781-A.

This eyelet bushing is made from higher grade rubber and unlike the NOS and other reproductions has a solid center shaft. The center shaft of this reproduction is a flat piece of steel that is bent into a circle to make the shaft for the eyelet bolt to go through, just like NOS.  Two per car, these are used on one end of the leaf springs and the shackles are used at the other end. Replaces Ford Part #: C7WY-5781-A, C4DZ-5781-C, C5ZZ-5781-A, D3ZZ-5781-B. ...

Poly eyelet bushing that will fit any 1967 through 1973 Mercury Cougar. Replaces Ford Part #: C4DZ-5781-C.

These have a different look than the reproductions and we only keep the very best ones, meaning we discard them if they are corroded, bent or have badly worn threads. In addition to carefully inspecting each one we chase the threads on both the bolt and the nut but of course we are careful not to over do it on the nut as they are designed to give resistance when threading them on. U-Bolt length 6-3/4 inches, and threads 1-1/4 inch in length. U-Bolts include two (2) correct style attaching nuts...

Leaf Spring U Bolt for the 1967 - 1973 Mercury Cougars with isolators. Will work on any 67-73 Cougar. Does not feature flattened area at top like original. Includes 1 'U' bolt and 2 nuts. 4 total U-bolts needed per car.  *Note - For use with Cougar shock plate, angled wedge, rubber isolators and retainer boxes. Inside Height:   6-3/4"Inside width:   2 7/8"  (Same as axle tubes) Replaces Ford Part #: C7WY-5705-A. ...

Sold individually. Has correct flattened area at top. Competition handling size, measures 7" from inner radius to end of threads. Thread size 7/16-20".  Does not include the OEM style nuts, those are an optional addon.  Replaces Ford Part #: C6OA-5705-C

Application: most 1967-1973 with any V-8 engine. A Right and Left bracket are needed for most applications. Including all 1968 - 1970 428 CJ automatic transmission Cougars. **Excludes 1969 - 1970 Boss 302 & 428 Cobra Jet 4 speed Cougars. That application had staggered rear shock plates. Hint - that would be two C9OZ-5796-C right side shock plates.Replaces Ford part number C9OZ-5796-B.

This 3 degree wedge properly sets the pinion angle for the drive shaft. This is a Cougar specific part which is needed due to the longer than normal rear leaf spring length. There are other wedges, but we seldom see them. This 3 degree marked wedge is the most prolific one. Feel secure in using these as a replacement.  Sold individually, two required per vehicle. Orientation: Narrow end towards the front of the car.

Correct shackle for all 1967 through 1973 Cougars, except those manufactured between 10/70 and 9/71. Measures 3-1/2 inches from center to center. Bushing dimensions: Length 1 1/8", outside diameter 1" (shaft piece) - 1 1/4" (end piece), hole diameter 1/2" Sold individually, two required per car. Replaces Ford 5630 shackle kits that include bushings C4GY-5781-A and D4DZ-5781-A.

Correct length (3-1/2 inches from center to center) and construction shackle for all 1967 through 1973 Cougars, except those manufactured between 10/70 and 9/71. Ships complete - 2 piece shackle with original nuts. New bushings not included, but recommended. Sold individually, but two are required for the rear suspension. Replaces Ford 5630 shackle kits that include bushings C4GY-5781-A and D4DZ-5781-A.

Complete Set of 1" leaf spring rubber bushings for the rear eye of the spring shackle. Sold in packages of 8, 4 per side. Correct size for the 1967 - 1973 Mercury Cougar except for 1971 through 1972 Cougars manufactured between 10/70 and 9/71. Replaces Ford Part #: D4DZ-5781-A. *except for 1971 through 1972 Cougars manufactured between 10/70 and 9/71.

Complete Set of 1" leaf spring poly bushings for the rear eye of the spring shackle. Sold in packages of 8, 4 per side. Correct size for the 1967 - 1973 Mercury Cougar except for 1971 through 1972 Cougars manufactured between 10/70 and 9/71. Replaces Ford Part #: D4DZ-5781-A. May be dropshipped. *except for 1971 through 1972 Cougars manufactured between 10/70 and 9/71.

Set of Four Reproduction Rear Leaf Spring Center Mount Insulator Pads for the 1967 - 1973 Mercury Cougar. Not factory, but also fits Ford Mustang. Reduce vibration and prevent metal to metal contact at the same time with new spring insulators. This molded rubber leaf spring insulator installs in the center of the leaf spring on the top & bottom side, above the spring perch and below the insulator retainer. 4 per car. Manufacturer lists the following applications: MakeModelBody...

These coarse thread nuts have an integrated lock washer with serations for the Mercury Cougar or Ford Mustang. They will ONLY work with the U-Bolts used in conjunction with the lowering kits. The thread size is 7/16"-14. *NOTE* Eight of these are required per car and are sold individually.

Reproduction Rear Leaf Spring Center Mount Insulator Pad for the 1967 - 1973 Mercury Cougar. Not factory, but also fits Ford Mustang. Reduce vibration and prevent metal to metal contact at the same time with new spring insulators. This molded rubber leaf spring insulator installs in the center of the leaf spring on the top & bottom side, above the spring perch and below the insulator retainer. 4 per car. Manufacturer lists the following applications: MakeModelBody StyleNotesYearMercur...

Used rear leaf spring retainer for 1968 -73 Mercury Cougar with standard or non-GT / non- competition handling suspensions. Additionally it fits most 1966-70 Mercury Comet / Montego, 1970-71 Ford Torino. Identified with a stamped number "6" on the top. The inside height is 1-3/4 inches. Sold individually, one for each side for a total of 2 per car. Bead blasted for pictures, most will ship 'as removed'. This suspension part never came painted, there will be some erosion due to...

Nice reproduction of the Boss 302 throttle bracket as found on the G code Boss2 cars. Includes 1969-70 Cougar Eliminator and Mustang. Similar to the 428 Cobra Jet bracket but with an extended spring tab.

Bracket that mounts in the rear Carburetor mounting holes of all 1969 and 1970 351 Windsor 2 barrel or H code engines. Has the square hole that holds the factory throttle cable.Replaces Ford part number C9ZZ-9741-D.

Reproduction Concours Correct throttle return spring.Replaces Ford Part # : C9ZZ-9737-A

Used bracket that mounts in the rear Carburetor mounting hole of all 1970 351 Cleveland 2 barrel engines. Has the square hole that holds the factory throttle cable. This bracket is identified by the hump or curve midway between the carburetor mounting studs.Replaces Ford part number D0OZ-9741-A.*Note - Not for use with 351 Windsor engines, or M code 351C-4V engines.

These shocks are the as close to original specs as possible for the Mercury Cougar. This is the comfort shock for those looking for a softer ride. The KYB Gas-a-Just shocks use higher gas pressure to keep your tires glued to the road. The KYB Gas-a-Just shocks' velocity-sensitive valving system adjusts quickly to changing road conditions for maximum comfort in any situation. Their mono tube configuration eliminates aeration and foaming, their micro-smooth, hard-chromed pistons extend their...

New axle bearing for any 8 or 9 inch Ford rear end with 28 splined axles. Common on all Mercury Cougar and Ford Mustang with V-8 engines. Excludes 31 splined axles as found on Boss and Cobra Jet cars.These should be professionally installed with a bearing press.

New outer axle gasket for any 8 or 9 inch Ford rear end with 28 splined axles. Common on all Mercury Cougar and Ford Mustang with V-8 engines. Excludes 31 splined axles as found on Boss and Cobra Jet cars. One required per side, two per car.

Rear axle vent bolt for the 67 - 73 Cougar or Mustang. This bolt serves a dual purpose, as it also holds the brake line bracket in place on the axle tube.

Reproduction leaf spring center bolt for your 67 - 73 Mercury Cougar.

Used passenger side leaf spring, front mounting bracket. All the same 1968-73 on Mercury Cougar. 1967 Mercury Cougar available, but slightly different in construction. You will receive the bracket attached to the unibody cut similarly to what is shown in the photo. 

Used driver side leaf spring, front mounting bracket. All the same 1968-73 on Mercury Cougar. 1967 Mercury Cougar available, but slightly different in construction. You will receive the bracket attached to the unibody cut similarly to what is shown in the photo. 

Used passenger side leaf spring, front mounting bracket. 1967 Mercury Cougar. 1968-73 Mercury Cougar available, but slightly different in construction. You will receive the bracket attached to the unibody cut similarly to what is shown in the photo.