All Available Parts - 1968 Ford Mustang

Reproduction passenger side inner A pillar inner / kick panel for the 67 - 68 Cougar or Mustang.

Reproduction driver side inner A pillar inner / kick panel for the 67 - 68 Cougar or Mustang.

This kit contains fasteners are duplicates of the originals as defined within the factory manuals.

This shim, also referenced to as washers, goes in the clutch portion of the drive gearbox to properly adjust the friction. Three shims (plus a hand crank) were originally supplied with sunroof cars.

Used unique Phillips bright finish screw that attaches cable guides to roof.

Reproduction proportioning valve line for Mercury Cougar and Ford Mustang.

Reproduction proportioning valve line for Mercury Cougar and Ford Mustang.

Exact copy of the hard to find original. This two piece clip is used to mount gas and/or brake line to floor pans.

Reproduction brake light switch for the Mercury Cougar and Ford Mustang equipped with power disc brakes. This is a high quality replacement part, but the appearance is not original. Ford originally called this unit the stop lamp switch. Replaces Ford Part #: C9VY-13480-A.

Reproduction brake light switch for Mercury Cougars and Ford Mustangs equipped with manual brakes. Ford originally called these stop lamp switches.Replaces Ford Part #: C9ZZ-13480-A.

Reproduction brake light switch for the Mercury Cougar or Ford Mustang equipped with both power drum or disc brakes. This switch fits the 1967-68 for power drum or disc brake applications, and 1969-70, this switch fits power disc brake applications. Ford called this unit the stop lamp switch. Replaces Ford Part #: C7ZZ-13480-B or C9ZZ-13480-B.Fits: 1967 Mercury Cougar (power drum or disc)1968 Mercury Cougar (power drum or disc)1969 Mercury Cougar (power disc)1970 Mercury Cougar...

Reproduction bushing for the master cylinder push rod where the switch and brake pedal converge. Two required per car and the bushings are sold separately.Ford part number C5DZ-2B129-B

Sold individually, phosphate & Oil (gray-black).

Reproduction driver (left hand) side drum brake self adjustor repair kit for your Mercury Cougar or Ford Mustang. This kit contains all the parts necessary to refurbish the self adjusting mechanism on drum brakes. Includes new cable and guide, ratchet, spring, and all necessary small parts. Kits include everything for one wheel.

Reproduction drum brake backing plate hole cover plug. Replaces Ford Part # 8A-2092.

Complete reproduction front drum brake spring kit for Ford Mustangs equipped with 9" drums. This kit contains all the replacement springs and hold downs required to do a professional brake job on front drum brakes. Kit includes enough parts for two wheels.

Contains all the replacement springs and hold downs required to do a professional brake job on drum brakes, front or rear. Kit includes enough parts for two wheels.Fits 10 x 2, 10 x 2-1/4, and 2-1/2 inch drum brakes.*Hint - Use your camera phone to take pictures of your brake assembly prior to disassembly, and do one side at a time. Sort out and match all of the springs up exactly, they are side and position specific.*NOTE* Kit does not include hardware for rear emergency brakes. ...

Reproduction drum brake spring and hold down kit for Mercury Cougars or Ford mustangs equipped with 10"x2" drums. This kit contains all the replacement springs and hold downs required to do a professional brake job on 1969-73 Mercury Cougar or Ford Mustang 10" x 2" rear drum brakes. Kit includes enough parts for two wheels. *Hint - Use your camera phone to take pictures of your brake assembly prior to disassembly, and do one side at a time. Sort out and match all of the springs up exactly,...

Reproduction brake shoe guide plate, or anchor pin, that holds the top of the drum brake shoes together on your Mercury Cougar or Ford Mustang equipped with drum brakes. These have 1/2 inch holes in them, like the originals.Replaces Ford part number C4UZ-2028-A.

Used brake light warning switch for Mercury Cougar or Ford Mustang and Torino and is identified by the two pin connector. Screws into the brake distribution block. On a dual reservoir master cylinder this switch is supposed to light up if one side or the other loses pressure. For both disc and drum brake systems. Fits most if not all 1968-69 Ford and Mercury cars.Ford part # C8AZ-2B264-A.

New front10 X 2-1/2 inch brake shoes for the Mercury Cougar or Ford Mustang. These will fit the rears of some Ford vehicles, but not a Cougar or Mustang without modification.Typically this size of brake shoes is only found on the front of a Cougar or Mustang. You would have to have 2-1/2 rear backing plates in order to use these shoes on the rear of your car.

This used emergency / parking cable anchor bracket is spot welded to your passenger side (right hand) front floor pan and anchors the cable. Comes "as taken from parts car". *Customer Feedback* from mercurycougar.net: "Best guys to always talk to about Cougars..will take the time on the phone with you, call you back if you leave a message, got all the time in the world for you when your talkin 'cause your important to them. Greatest thing for our hobby. Thanks Lin and Don for making/getting...

Keeps proper tension on emergency / parking brake cable by taking up the slack when the brake is off. Hook attaches to the bracket under the passenger side floor. Replaces Ford Part # C7ZZ-2A808-A.

Reproduction emergency / parking brake retainer clip set for the Mercury Cougar or Ford Mustang. These units are sold in a set of 3.

This reproduction emergency / parking brake cable equalizer mounts to the end of the parking brake release assembly and captures the emergency brake cable. A very nice reproduction!Replaces Ford part # C6OZ-2A602-A.

This reproduction emergency / parking brake spring for the V8 Mercury Cougar or Ford Mustang is made from original Ford blue prints. This is the oblong spring that is painted RED like the originals, rests upon the parking brake cross bar link between the shoes.These springs came from the factory in either Red or Yellow.You can find the Yellow spring here.Replaces Ford part # C2OZ-2601. ...

Concours correct premium grade reproduction driver side (left hand) rear emergency / parking brake cable. This is the short one located on the driver side and is an exact fit for 1968 and 1969 Mercury Cougar and Ford Mustangs.

Reproduction front emergency / parking brake cable for the Mercury Cougar or Ford Mustang. These are made just like the originals, are concours correct and includes the firewall seal and firewall bracket. Replaces Ford part # C7ZZ-2853-A.

This reproduction driver side (left hand) emergency / parking brake cable fits from the equalizer to rear brakes. 1 required per vehicle. The cable length is approximately 29-1/2". Cougars manufactured after 2/69 may use the 1970-73 left hand cable. It is easy to check by measuring the cable. The 1968 cable is just over 29" long, and the 70 cable is just over 32" long. Click on the image to left to see the difference. The 1968 style of emergency brake cables can be used on the 1967 cars, as...

Reproduction passenger side (right hand) rear emergency / parking brake cable that fits from the equalizer to rear brakes. 1 required per vehicle. Cable length is approximately 136 5/8". Correct for 1968 Mercury Cougar and Ford Mustang, but fits 1967 Mercury Cougar and Ford Mustang with the companion left side cable. Replaces Ford part # C8ZZ-2A635-A.

This reproduction emergency / parking brake equalizer lever is made from heavy gauge stamped steel and is a quality reproduction. Replaces Ford part # C7ZZ-2A605-A.

Reproduction steel emergency / parking brake adjustment rod for the Mercury Cougar or Ford Mustang and is threaded for full adjustability. Replaces Ford Part # C7ZZ-2628-B.

Keeps proper tension on emergency / parking brake cable by taking up the slack when the brake is off. Hook attaches to the bracket under the passenger side floor. Replaces Ford part # C7ZZ-2A808-A.

This attaches to the end of the cable that attaches to the hand ratchet e-brake. It is spot welded to the floor pan and frame rail and is often over looked when floor pans are replaced. The unit you receive will need clean up, but will not be heavily rusted.

This used emergency / parking brake idler bracket welds to the under side of the floor on the driver side (left hand) of the vehicle. Will most likely be missing pin.

Passenger side rear brake cable bracket. This is a part cut from a car, some trimming and or spot welds will need to be removed prior to installation. Fits all 1967-69 Mercury Cougar and Ford Mustang.

[No Description Provided]

Used emergency / parking brake equalizer lever. Good used part, fits any 1967-68 Mercury Cougar or Ford Mustang. Part was cleaned for the photograph. Most all of our levers come from Cougars, typically they have a generous amount of under coating that partially covers these levers and protects them. In other words, as they come off of the cars.Replaces Ford part # C7ZZ-2A605-A.

This used emergency / parking brake cable equalizer mounts to the end of the parking brake release assembly and captures the emergency brake cable. Replaces Ford part # C6OZ-2A602-A.

This reproduction emergency / parking brake spring for the V8 Mercury Cougar or Ford Mustang is made from original Ford blue prints. This is the oblong spring that is painted YELLOW like the originals, rests upon the parking brake cross bar link between the shoes.These springs came from the factory in either Red or Yellow.You can find the Red spring here.Replaces Ford part # C2OZ-2601. ...

Clip or X-washer for attaching the emergency brake lever inside the rear brake drum. Fits 8 and 9 inch rear axles. Literally used on most all Ford products from 1965-73 and likely beyond. Also called a retainer for the parking brake lever pin. The long ears get squeezed with a good set of pliers for attaching. Replaces Ford number 91A-2106. 

NOS emergency / parking brake handle.  To remove your old handle break the plastic off of the shaft to reveal the splined pin. Pull out pin with vise grips and install the new unit.

Passenger side caliper mounting bracket, also called a caliper anchor bracket in the Ford Master Catalog. Ford part # C8OZ-2B292-A Check out this video Check out our caliper tips and tricks video below: ...

Driver side caliper mounting bracket, also called a caliper anchor bracket in the Ford Master Catalog. Ford Part Number C8OZ-2B293-A Check out this video Check out our caliper tips and tricks video below: ...

Stamped steel bracket that mounts on the rear of the calipers. These often fracture or rust out. We only sell the pristine units, two required per car, PS and DS are the same. Ford part # C8OZ-2B295-A Check out this video Check out our caliper tips and tricks video below: ...

Reproduction grease cap for front wheels of the Mercury Cougar or Ford Mustang. 2 Required per car, sold individually. Replaces Ford part # B5A-1131.

Good clean used passenger side (right hand) brake spindle for your Mercury Cougar or Ford Mustang equipped with front drum brakes. Cars with disc and drum brakes used the same spindle in 1967, but this spindle was carried over through 1969 on drum brake cars only. Bearing surface measurements: 0.75" and 1.25". We check these very closely, and if they are not perfect, we chuck'em into the scrap pile. All have a Ford C6O... casting number.Ford part # C9OZ-3105-C. Check out this video ...

This is a front brake grease dust cap tool. No more dented caps. These are milled from 6061 solid aluminum.

Good clean used driver side (left hand) brake spindle for your Mercury Cougar or Ford Mustang equipped with front drum brakes. Cars with either disc or drum used the same spindle for 1967, but this spindle was carried over through 1969 for drum brakes cars only. Bearing surface measurements: 0.75" and 1.25". We check these very closely, and if they are not perfect, we chuck'em into the scrap pile. All have a Ford C6O... casting number. Ford part # C9OZ-3106-C.Check out our...

Cork gasket for the disc brake splash shield. Fits all 1968-73 Mercury Cougar and Mustang and 1968-71 Ford mid size including Torino, Cyclone, Ranchero, Fairlane.Replaces Ford part number C8OZ-2B160-A.

New front outer wheel bearing for original drum and disc brakes for all 1967-69 Mercury Cougar and 1967-69 Ford Mustang with V-8 engines. These are tapered bearings with cone or race. Inner diameter is 0.75 inches. These are dry bearings, meaning they will need to be packed with chassis bearing grease, prior to installation. A large inner bearing and this outer bearing are required for each side. Two of each needed for the front wheels. *Note - This bearing only fits the 1967-69 spindles,...

New front inner wheel bearing for original drum and disc brakes for all 1967-69 Mercury Cougar and 1967-69 Ford Mustang with V-8 engines. These are tapered bearings with cone or race. Inner diameter is 1.25 inches. These are dry bearings, meaning they will need to be packed with chassis bearing grease, prior to installation. A smaller outer bearing and this inner bearing are required for each side. Two of each needed for the front wheels. *Note - This bearing only fits the 1967-69 spindles,...

C9ZZ-2A637-A Parking brake lever that mounts between the parking brake cable and secondary brake shoe in your rear brake drum assembly. Ford service replacement part number for RH or passenger side is C9ZZ-2A637-A. Clean Western part with no heavy corrosion like you see on Eastern cars.

Used parking brake lever that mounts between the parking brake cable and secondary brake shoe in your rear brake drum assembly. Ford service replacement part number for LH or driver side is C9ZZ-2A638-A. This unit is from a solid Western parts car, so you won't be getting one of those rusty East Coast units! Ford part # C9ZZ-2A638-A.

Reproduction 10" parking brake link. Spring included. Sold individually, two per car. Replaces part Ford Number C2OZ-2A642-A

Parking brake link. The spring (not included) is wound in a rectangular shape to fit the one end of the link. Ford part # C2OZ-2A642-A.

This kit contains all the replacement springs and hold down components required to do a professional job on rear drum brakes. Kit includes enough parts for two wheels. This is for the 9 inch drum brakes commonly found on the early 6 cylinder cars with 7-1/4 inch rear ends.*Note - Kit does not include hardware for rear emergency brakes.

This kit contains all the replacement springs and hold downs required to do a professional job on 10" x 1-3/4" drum brakes. Kit includes enough parts for two wheels. *Hint - Use your camera phone to take pictures of your brake assembly prior to disassembly, and do one side at a time. Sort out and match all of the springs up exactly, they are side and position specific.*Note - Kit does not include hardware for rear emergency brakes.

Rear Drum Brake Wheel Cylinder for 390, 427, 428 w/ Front Disk Brakes (13/16", Right Hand & Left Hand same) You can find the premium concours correct version here. Replaces Ford Part #: C7ZZ-2262-A

Rear Wheel Cylinders for 4 Wheel Drum Brakes (15/16", LH). Replaces Ford Part #: C7AZ-2262-C.

Rear Wheel Cylinder for 4 Wheel Drum Brakes (15/16", RH) Replaces Ford Part #: C7AZ-2261-C.

Rear Wheel Cylinder (7/8", Right Rear) For 10 x 1-3/4 inch rear drum brake shoes. Typically 1967-68 Mercury Cougar or 1967-73 Ford Mustang with 289/302 cubic inch engines or smaller.You can find the premium concors correct version here. Replaces Ford Part #: C20Z-2262-B, C3AZ-2262-B, C4TZ-2262-A, C60Z-2262-A, D2ZZ-2262-A, D3TZ-2262-A, D3ZZ-2262-A. ...

Premium grade of rear brake shoes with semi metallic brake linings. 10 inch diameter drum brakes. Please measure your brake shoes, there are also 1-3/4 inch wide shoes too.

Also used some 69-73 Mustangs.

Quality replacement brake drum. # of Bolt Holes : 5 Inside Diameter : 254 mm Bolt Circle Diameter : 114.3 mm Brake Drum Surface Depth : 71.6 mm Center Bore Diameter : 61.8 mm Maximum Discard Diameter : 256.3 mm O.D. : 296.3 mm Replaces Ford Part #:C2OZ-1126-B

Quality replacement brake drum. # of Bolt Holes : 5 Inside Diameter : 254 mm Bolt Circle Diameter : 114.3 mm Brake Drum Surface Depth : 53.9 mm Center Bore Diameter : 61.8 mm Height : 84.5 mm Maximum Discard Diameter : 255.52 mm O.D. : 295.5 mm Replaces Ford Part #: C3OZ-1126-B.

Reproduction parking brake lever that mounts between the parking brake cable and secondary brake shoe in your rear brake drum assembly. 1967-73 Mercury Cougar or most Fords including Mustang. Fits 10 inch drum rears. Replacement part number for RH or passenger side original part Ford number is C9ZZ-2A637-A.

Reproduction parking brake lever that mounts between the parking brake cable and secondary brake shoe in your rear brake drum assembly. 1967-73 Mercury Cougar or most Fords including Mustang. Fits 10 inch drum rears. Replacement part number for LH or DRIVERS side original part Ford number is C9ZZ-2A638-A.

4 oz. tube of non-melting, water resistant grease for disc and drum brake hardware, hood hinges, window regulators, quarter windows, vent window hinges, pretty much whatever needs lubing. A little dab will do ya!Do you have questions about Glue-In vs Bolt-In glass? How about how to properly install Glue-In glass in your 1969 Cougar or Mustang? Check out our video below for some great glassy information!1969 Glue-In Glass: The Comprehensive Repair Guide Video ...

Push on retainer for rear drum brakes. 2 or 3 of these were used to hold the rear brake drums onto the rear axle assembly during construction of your 1967-73 Mercury Cougar or 1965 - 73 Ford Mustang. While not necessary, these are a neat concours item. Sold individually.  Ford part number 372188-S

Rear Drum Brake Wheel Cylinder for 390, 427, 428 w/ Front Disk Brakes (13/16", Right Hand & Left Hand same) The difference in this premium version and the economy version, is that this cylinder will be concours correct and have the smaller 1/4" fitting. Replaces Ford Part #: C7ZZ-2262-A

Rear Wheel Cylinder (7/8", Right Rear) For 10 x 1-3/4 inch rear drum brake shoes. Typically 1967-68 Mercury Cougar or 1967-73 Ford Mustang with 289/302 cubic inch engines or smaller. The difference in this premium version and the economy version, is that this cylinder will be concours correct and have the smaller 1/4" fitting.Replaces Ford Part #: C20Z-2262-B, C3AZ-2262-B, C4TZ-2262-A, C60Z-2262-A, D2ZZ-2262-A, D3TZ-2262-A, D3ZZ-2262-A. ...

Rear Wheel Cylinder (7/8", Left Rear). For 10 x 1-3/4 inch rear drum brake shoes. Typically 1967-68 Mercury Cougar or 1967-73 Ford Mustang with 289/302 cubic inch engines or smaller.The difference in this premium version and the economy version, is that this cylinder will be concours correct and have the smaller 1/4" fitting. Replaces Ford Part #: C20Z-2261-B, C3AZ-2261-B, C4TZ-2261-A, C60Z-2261-A, D3TZ-2261-A, D3ZZ-2261-A. ...

Rear Wheel Cylinder (7/8", Left Rear) For 10 x 1-3/4 inch rear drum brake shoes. Typically 1967-68 Mercury Cougar or 1967-73 Ford Mustang with 289/302 cubic inch engines or smaller. You can find the premium concours correct version here.

This reproduction emergency / parking brake handle is an exact reproduction that is made from quality materials and is less prone to cracking than your original. That being said, these still will crack if you pull hard and do not have your hand close to the shaft.  This was a design flaw from day one.  The correct way to apply the brake to reduce the chances of these handles cracking is to split your fingers around the shaft when applying the brake, keeping your fingers close to the...

Reproduction emergency / parking brake assembly that is a complete system and ready to bolt in. Looks better than even our grade "A" used one at first glance, but this off shore unit will never hold up as well as our original FoMoCo good used units.

Used emergency / parking brake assembly for a Mercury Cougar or Ford Mustang as removed from a West Coast Cougar organ donor. This unit may have some minor rust. Normally we assemble with reproduction cable.Ford part # C7ZZ-2780-B.

New hairpin clip for attaching the brake light switch to the brake pedal. This clip was also used to attach the clutch rod to the clutch pedal on manual transmission cars. Fits all years 1967-73, Ford and Mercury.Replaces Ford part number 380699-S.

These new brake drums are perfect replacements for tired and thin originals on you Cat or Pony. Fits cars with either the 2 1/4 inch or 2 1/2 Inch shoes. Front drums do not include studs or a hub. Drums Provide Consistent Quality & Reduced Noise.; Drums Are Vehicle Specific & Meet Federal Safety Standards.; Castings Meet Sae J431/g3000 Specifications For Proper Tensile Strength.; Machined To Control Perpendicularity & Run-Out For Optimal Performance & Brake Life.Also fits V8...

Used passenger (right hand) side brakes shoe adjustor for Mercury Cougar or Ford Mustang. This screw assembly is part of the manual and self adjusting system for your drum brakes either front or rear. These have right and left handed threads depending upon which side of the car they are intended. Right side screws are identified by an "R" on the end of the screw under the socket and a two grooves machined into the pivot nut. Original Ford part number for RH or passenger side is C2OZ-2041-A,...

Used driver (left hand) side brake shoe adjustor for Mercury Cougar or Ford Mustang. This screw assembly is part of the manual and self adjusting system for your drum brakes either front or rear. These have right and left handed threads depending upon which side of the car they are intended. Left side screws are identified by an "L" on the end of the screw under the socket and a single groove machined into the pivot nut. Original Ford part number for the passenger (right hand) side is...

Midland boosters with power drum or power disc brakes and includes the grommet. The check valve diameter is 0.830" for a 13/16" hole and the hole in the Midland boosters is right at 1.040" in diameter.

Used brake shoe guide plate, or anchor pin, that holds the top of the drum brake shoes together on your Mercury Cougar or Ford Mustang equipped with drum brakes. For the money our reproduction plate is a better value and cleaner, too. These have 1/2 inch holes in them.Replaces Ford part number C4UZ-2028-A.

Kit for rebuilding your drum brake distribution block on your Mercury Cougar or Ford Mustang. Special square O-rings are made from EPDM (Ethylene Propylene 70 Durometer) which is specifically designed to withstand chemical degradation caused by prolonged exposure to brake fluid.*Customer Feekback*"You guys are awesome, I couldn't find a rebuild kit for my Galaxie's brake distribution block anywhere else! Thank you!" Henry M.Check out this video ...

Reproduction passenger (driver hand) side drum brake self adjuster repair kit for your Mercury Cougar or Ford Mustang. This kit contains all the parts necessary to refurbish the self adjusting mechanism on drum brakes. Includes new cable and guide, ratchet, spring, and all necessary small parts. Kits include everything for one wheel.

New front drum brake hub for all Mercury Cougars equipped with front drum brakes. Pretty much fits most front 5 lug 10 inch front drum brakes on all mid sized Ford and Mercury cars. Front drum brakes only. Fits 1967-69 Mercury Cougar and 1965-69 Ford Mustang with 5 lug 10 inch drums. Several manufacturers of the front drum assemblies such as Kelsey Hayes and Bendix were suppliers to Ford over the years. Quite a bit of labor to press these out. Needs threaded studs, see related...

This is a replica of the warning tag that came on positive (+) terminal of Autolite batteries when the 1967 - 1972 Cougars and Mustangs were shipped from the factory.

Replica of the coil spring shipping tag that would have been found on factory delivered 1967 - 1973 Cougars and Mustangs.

Reproduction Small Block Engine I.D. Bolt for the  1967 - 1973 Mercury Cougar / 1967 - 1973 Ford MustangSold individually 

Replaces Ford Part #: C7ZZ-19959-A.

A/C compressor clutch decal for Mercury Cougar and Ford Mustang.Replaces Ford Part #: C7AA-2987-D.

This is a reproduction of the original Autolite parts decal that was located on the air cleaner.Fits the following models with a BOSS 302 engine:1968 Mercury Cougar 1969 Mercury Cougar 1970 Mercury Cougar 1971 Mercury Cougar 1972 Mercury Cougar 1968 Ford Mustang 1969 Ford Mustang 1970 Ford Mustang 1971 Ford Mustang 1972 Ford Mustang ...

This is a reproduction of the original Autolite parts decal that was located on the air cleaner.Fits the following models:1968 Cougar1968 Mustang

This is a reproduction of the original Autolite parts decal that was located on the air cleaner.Fits the following models:1968 Cougar1968 Mustang

This is a reproduction of the original orange engine displacement decal with black lettering and black and white checkerboard on each end that was located on the top of the air cleaner.Fits the following models with the 390 4 barrel engine:1968 Cougar1968 Mustang

This is a reproduction of the original orange engine displacement decal with black lettering and black and white checkerboard on each end that was located on the top of the air cleaner.Fits the following models with a 428 4 barrel Cobra Jet engine:1968 Cougar1968 Mustang Replaces Ford Part #: C8AF-9C611-D

This is a reproduction of the original orange engine displacement decal with black lettering and black and orange checkerboard on each end that was located on the top of the air cleaner.Fits the following model with a 289 2 barrel engine:1968 Mercury CougarReplaces Ford part# C8DF-9C611-B

Reproduction Autolite parts plug decal for the 1968 Cougar or Mustang. Attaches to the side of the air cleaner base.

Reproduction 390 / 428 4V AT / MT Emission Decal for the 1968 Mercury Cougar / Ford Mustang

Replaces Ford Part #: C8DE-9C485-C