All Available Parts - 1968 Ford Mustang

Oil seal for rear axle on any 1968-73 Mercury Cougar or Most Ford cars with 31 spline axles. Typically only 428CJ, 427-4V, and Boss 302's got the heavy duty 31 splined axles from the factory, most Cougar and Mustangs have 28 splined axles. Seal measurements: 1-1/2 inch inside diameter, 2-17/64 inch outside diameter. Two needed per axle, sold individually. We stock Timken brand of seals.Replaces Ford part number C7OZ-1177-A.

Oil seal for rear axle on any 1967-73 Mercury Cougar or Most Ford cars with 28 spline axles. Most all Cougar and Mustang received 28 splined axles, whether they have an 8 inch or nine inch rear end from the factory. Seal measurements: 1-3/8 inch inside diameter, 2-17/64 inch outside diameter. Two needed per axle, sold individually. We stock Timken brand of seals.Replaces Ford part number C7OZ-1177-B.

This is the 4 hole version of the ball joint for the 1967 - 1969 Cougar and Mustang. Right is same as left. Two required per car. Hardware included.

Reproduction pinion seal for the 9 inch ring gear on the 1967 - 1973 Mercury Cougar or Ford mustang. 

Reproduction Autolite gas tank to filler pipe hose fits the 67 to 70 Mercury Cougar, measures 4 1/2" long. Excludes 1970 with California emissions. Even if yours is not cracked it will be hard if it is over two decades old. We highly suggest you replace this part if yours is in fact hardened with age because a minor rear end collision could cause it to fail and send fuel spilling into your trunk area. Replaces Ford part #: C8ZA-9047-A. ...

Reproduction foam rubber donuts that help cushion the brace from the tail panel on any 67 - 73 Cougar or Mustang.Replaces Ford part number C5ZZ-6540996Sold as a set of 4.

Four per car, mounts to fenders. Replaces Ford part #: C7WY-16758.

Used firewall grommet which your under hood harness runs through. This grommet is the same for Standard and XR7.

This is the seal at the back of the booster on the Midland-Ross units.

Clear plastic cowl seals for all 1967-68 Mercury Cougar and Ford Mustang. These are supposed to prevent rain or water from entering your cowl vents in front of the windshield. These were created to help prevent water from dripping on your floor from leaking cowls. These fit fairly well, but you need to check all of the corners when installing. We feel that they are a little under sized to properly seal those cowls easily. Our first attempt left one of the corners with a gap, thereby allowing...

NOS wiring pigtail without the resistor wire for repairing ignition switches on 1968-69 Cougars, Mustang, and other Fords.Ford part number C9AB-14313-A.

Reproduction rubber grommet for the air conditioning case. This grommet encloses the tubes for the evaporator, and slides into a slot on the heater box. Fits 1967-1969 Mercury Cougar and Ford Mustang. 1969 owners, please compare your grommet to the picture, late 1969 changed to a triangle shaped grommet. Please see related items for late 1969-73 rubber grommet. Replaces Ford part number C7ZZ-19B552-A. Check out our videos below on how to replace a heater core! We now have separate videos for...

New rubber boot for brake push rod to the master cylinder on all drum brake cars. Fits all 1967-72 Mercury Cougar and 1965-73 Ford anything cars, including Mustang.Trivia - Did you know that 100% of all 1973 Mercury Cougars, came from the factory with front power disc brakes?

This is a much cheaper version of the foil sound deadeners and underlays we sell. This particular insulation is basically bubble wrap with two layers of foil on both sides. Good for insulating headliners, floor pans, trunk areas, door panels, kick panels and just about anything else you might want to use it for. This insulation comes in a 48" X 72" roll. Just grab a pair of scissors and cut your shapes. You can use any adhesive you like (contact cement or weatherstrip adhesive,...

Cut off a dry Western car in the 1980's and stored in the attic of a barn ever since. Cut large, no rust or previous damage, perfect for the high end car that deserves the very best. Better than NOS as you ger all the factory spot welds, includes PS trunk floor as well. Shipping and crating at reasonable cost, call 503-463-1130 for more info, ask for Don.

Set of four in the box, no blemishes.Ford part number C8OZ-1130-COther Applications: Torino Fairlane Ranchero

This is a radio nut removal tool used to remove the radio shaft nuts. No more trying to remove those little units with the wrong tools and potentially damaging your bezel or dash. These are made from HRS steel and are milled to fit the shaft nut perfectly.

Great investment considering how easy it is to mar your switch, bezel or dash paint when trying to remove your ignition switch bezel with a hammer and screw driver. We also have a handmade version of this same tool for a lower price.

Set comes with economy grade pliers and 150 hog rings, enough for one bucket seat, probably two.

This is a mirror nut bezel tool used to remove the mirror nut on the 1967 - 1968 and 1970 - 1973 Cougar. No more scratches trying to remove with the wrong tools. These are made from HRS steel and are milled to fit the bezel nut. This tool pays for itself each time you use it. NOTE: This is an exact fit for ALL used mirror nuts (bezels) and the 1970 - 1973 reproduction mirror nuts (bezels). However, you will find it does not fit our 67-68 repro mirror nuts (bezels) and will need some...

New coil spring compressing tool to compress the coil springs of the 1967-73 Mercury Cougar or 1965-73 Ford Mustang. This tool now comes with a bearing to make the job much easier. This spring compressor is a must for safely removing front coil springs. We also offer a 60 Day Loaner if you only need the tool for a short period of time. *NOTE* Not recommended for heavy duty coil springs like found on pickup trucks and full sized cars. ...

We will loan this coil spring compressor for 60 days, with a 100% refundable purchase price. This tool now comes with a bearing to make the job much easier. Only available to customers that purchase our front suspension rebuild kits. Tool must be returned in undamaged condition with no missing parts within the 60 day time period. Returns past 60 days are subject to a 25% restocking fee. Coil spring compressing tool, this is a must for safely removing front coil springs on any 1967-73...

New strip caulk for the Mercury Cougar or Ford Mustang. These units come in one foot strips and are used for sealing the front fenders to top of aprons and for sealing the fuel tank flange to the trunk floor. They are also used for sealing the floor drain plugs, gas filler necks, door panel water shields, plus many other components that are fastened to the body. This box contains 60 individual strips of black non-hardening caulk.

No more crust, white powdery battery terminals. Just spray this stuff on, and after a few minutes....simply wash off with water! Not only can you use this stuff on your car, you can use it on your ATV's, quads, dirt bikes and even your ride on lawnmower! A handy item to have laying around your garage. Of course, there's a little more messy, mostly free alternative which you can find the ingredients for online, but why bother? This is a simple, fairly cheap product to have.  

Permatex RTV gasket maker for the automatic transmission in your Mercury or Ford. Great stuff for sealing up that leaky transmission pan gasket!

New adhesive / epoxy applicator to apply our 3M window adhesive to the glass (or whatever else needs bonding) in your Mercury or Ford. This non-drip unit features an easy loading breech, a 1:1 mixing ratio and full cartridge support. We also offer a 60 day loaner if you only need this unit for a short time. ...

We will loan you this adhesive / epoxy applicator for 60 days, with a 100% refundable purchase price. Only available to customers that purchase our 3M bonding adhesive. Tool must be returned in undamaged condition with no missing parts within the 60 day time period.Returns past 60 days are subject to a 25% restocking fee. ...

New red permanent strength thread locker for your project. This is a must have item if you are reassembling your pride and joy after restoration or just changing out parts. Often times, the vibrations from these antiques can vibrate loose the fasteners used to hold it together. If you use this, you can rest assured that your Merc or Ford will not fall apart from fasteners that have vibrated loose.

New RTV gasket maker for use on the differential of your Mercury or Ford. This gasket maker is specially formulated to withstand today's gear oils and prevent leakage.

New RTV  oil resistant, high temperature, Ultra Black gasket maker for use on the Mercury or Ford. It's no mistake that Ultra Black has become an automotive industry standard. It's low odor, flexible, non-corrosive, vibration resistant, oil resistant, heat resistant, fast curing formula cannot be beat. Great for use on any surface that experiences high heat and oil like the valve cover gaskets.

New blue removable strength thread locker for your project. This is a must have item if you are reassembling your pride and joy after restoration or just changing out parts. Often times, the vibrations from these antiques can vibrate loose the fasteners used to hold it together. If you use this, you can rest assured that your Merc or Ford will not fall apart from fasteners that have vibrated loose.

This is an upgraded version from what you see in our video but the idea is the same. This tool has a square hole so you can use your 3/8" drive ratchet or breaker bar to get the correct angle and have even better control of your leverage when placing the torsion bar into the slot. Used to remove the hinge springs (torsion rods) off the 1967 - 1973 Cougar or Mustang. No more trying to remove with the wrong tools . These can be tricky to remove without this tool.  Will not work on 1964 -...

CRC contact cleaner is intended for cleaning sensitive electronics and electrical equipment. Great for cleaning edge connectors, buss bars, circuits, contacts, printed circuit boards, switches, circuit breakers, etc. Safe on most plastics.

Clever tool that keeps the piston stationary in your brake distribution block. It is as simple as centering the piston and screwing in this tool, of course your have to catch the groove in the piston. Leave in until brakes are completely bled and functioning. Remove and install your brake warning light switch.

Bonding adhesive for plastic dash repair. Keep in mind that this adhesive has an extremely fast setting time. It's also available in slow set, which you can get here.

Epoxy adhesive for plastic dash repair. This is the slow setting version of this adhesive. It's also available in fast set, which you can get here.

Professional grade paintless dent removal kit. This kit is designed to work with smaller blemishes such as dents from hail, door dings, etc. Complete with universal high strength glue sticks, puller, and a variety of different sized gluing tabs. NOTE: Remove glue with 91% alcoholAlthough we work with 67 - 73 Cougars and Mustangs, this kit is good for a wide variety of different vehicles.

The POGO Stick works just like the larger Hustler stick but is much easier to ship. If you need more leverage you can just add a pipe for leverage. We will loan this hustler stick for 60 days, with a 100% refundable purchase price. Tool must be returned in undamaged condition with no missing parts within the 60 day time period. Returns past 60 days are subject to a 25% restocking fee. Check out this video ...

Great investment considering how easy it is to mar your switch, bezel or dash paint when trying to remove your ignition switch bezel with a hammer and screw driver. Black, basic handle tool removes and installs headlight switch bezels. When coupled with ignition bezel tool it removes and installs ignition switch bezels on any 1967-68 Mercury Cougar and Ford Mustang. A 5/32" Allen wrench is needed to attach tools together. Allen wrench included.  ...

Great investment considering how easy it is to mar your switch, bezel or dash paint when trying to remove your ignition switch bezel with a hammer and screw driver. Black, basic handle tool removes and installs headlight switch bezels on any 1967-70 Mercury Cougar or Ford Mustang. Additionally, it also removes the wiper switch on 1969-70 Mercury Cougar and Ford Mustang. When coupled with ignition bezel tool it removes and installs ignition switch bezels on any 1967-68, or 1969...

Great investment considering how easy it is to mar your switch, bezel or dash paint when trying to remove your ignition switch bezel with a hammer and screw driver. Ignition bezel adapter tool removes and installs ignition switch bezels on any 1967-68 Mercury Cougar and Ford Mustang. Should be coupled with the basic tool (item 32368) A 5/32" Allen wrench is needed to attach tools together. Allen wrench not included.  ...

Adapter tool for installing and removing remote door mirror bezels on 1967-68, and 1970-73 Mercury Cougar and Ford Mustang. Should be coupled with the basic tool (item 32368) A 5/32" Allen wrench is needed to attach tools together. Allen wrench not included. *Note - Excludes 1969 remote mirror bezels. ...

This kit is an easy way to covert your 289 / 302 / 351W engine from a C4 or C6 transmission to an Automatic Overdrive Transmission. Kit includes: Cross memberTrans Mount InsulatorSlip YokeKick Down CableFlex Plate AOD Shift Linkage This is just the kit, and does not include the full transmission!

Reproduction flexplate reinforcing ring. Strengthens the area where the automatic transmission flexplate mounts to the crankshaft. 5.12" outside diameter3.34" inside diameter .060 inches thickFits: 352 390 427 428 429 460 with C6 and FMX transmissions.Replaces Ford part # B9AZ-6A6366-B

Used flexplate reinforcing ring, Ford called it a fly wheel reinforcing plate. Fits all Ford small block engines including 260, 289, 302, 351W and 351C. Strengthens the area where the automatic transmission flex plate mounts to the crankshaft. This is not just a ring with 6 holes in it, it is indexed specifically for the flex plate and only goes on one specific way. It has to be indexed because of the weight on the flex plate. Just under 4 inches in diameter. Special bolts not included, but...

Core C-6 Transmission valve body for any 1967-68 Mercury Cougar or 1967-68 Ford Mustang with code "U" transmission code on the door tag. This is only for 1967 through 1968 transmissions with P-R-N-D-2-1 shift pattern. Sold as a core, should be thoroughly cleaned and rebuilt with quality parts. These units can be upgraded with 'shift kits' to firm up shifts, add longevity, and they help reduce and eliminate clutch and band slippage. Various kits available in the aftermarket, we offer one as...

Core C-6 Transmission valve body for any 1968-69 Mercury Cougar or 1968-69 Ford Mustang with code "U" transmission code on the door tag. Sold as a core, should be thoroughly cleaned and rebuilt with quality parts. These units can be upgraded with 'shift kits' to firm up shifts, add longevity, and they help reduce and eliminate clutch and band slippage. Various kits available in the aftermarket, we offer one as well. This is the special valve body for 1968 and 1969 428CJ engines. Ford installed...

This is the 1.37" X 1.66 X .31 plastic grommet that goes inside the trunk to protect the trunk wires from rubbing the edges of the sheet metal body. This grommet was also used for the hood light wiring under the hood.

This is the modern version of the Kelsey Hayes wheels that were originally equipped on 1967 Shelbys. One-piece cast aluminum structure with a CNC machined face and durable clear coat finish. The lighter weight one piece design also provides a significant weight savings over the original steel design, delivering improved acceleration and braking performance. These take specific lug nuts and center caps (sold separately, see related items). These wheels come with free chromed plastic center...

This wheel is inspired by the 1966 Shelby GT350 10 spoke alloy wheel. This updated design was created using state of the art casting technology for superior strength and precision. Each wheel features a CNC machined face with gloss black accents and a clear coat finish. These wheels take a specific shouldered 3/4" lug nut, find them here. These wheels come with free chromed plastic center caps. The caps have a red Legendary logo but we can include at no cost, a set of black and chrome walking...

Reproduction Legendary Series GT5 Alloy Wheel. This updated design was created using state of the art casting technology for superior strength and precision. These wheels take a specific shouldered 3/4" lug nut, find them here. These wheels come with free chromed plastic center caps. The caps have a red Legendary logo but we can include at no cost, a set of black and chrome walking cat decals (click here). Just add it to your cart if you'd like these decals. If you want to upgrade to a premium...

This wheel is inspired by the 1966 Shelby GT350 10 spoke alloy wheel. This updated design was created using state of the art casting technology for superior strength and precision. Each wheel features a CNC machined face with natural aluminum accents and a clear coat finish. These wheels take a specific shouldered 3/4" lug nut, find them here. These wheels come with free chromed plastic center caps. The caps have a red Legendary logo but we can include at no cost, a set of black and chrome...

Reproduction clear coat natural finish aluminum alloy rim for the 1967 - 1973 Cougar or Mustang. Designed to look like the optional 10 spoke alloy wheel that was available on 67 - 68 Shelby GT350's ang GT 500's. These wheels come with free chromed plastic center caps. The caps have a red Legendary logo but we can include at no cost, a set of black and chrome walking cat decals (click here). Just add it to your cart if you'd like these decals. If you want to upgrade to a premium quality center...

Reproduction clear coat natural finish aluminum alloy rim for the 1967 - 1973 Cougar or Mustang. Designed to look like the optional 10 spoke alloy wheel that was available on 67 - 68 Shelby GT350's ang GT 500's. These wheels come with free chromed plastic center caps. The caps have a red Legendary logo but we can include at no cost, a set of black and chrome walking cat decals (click here). Just add it to your cart if you'd like these decals. If you want to upgrade to a premium quality center...

Reproduction clear coat natural finish aluminum alloy rim for the 1967 - 1973 Cougar or Mustang. Designed to look like the optional 10 spoke alloy wheel that was available on 67 - 68 Shelby GT350's ang GT 500's. These wheels come with free chromed plastic center caps. The caps have a red Legendary logo but we can include at no cost, a set of black and chrome walking cat decals (click here). Just add it to your cart if you'd like these decals. If you want to upgrade to a premium quality center...

These T/A style wheels have the classic 8-spoke European design that was popular with road racers in the 60's and 70's. Fits the 60-73 Mustang, Falcon, Fairlane, Comet and 67 - 70 Cougar. Chrome plated plastic Legendary Wheel hubcap included. Back spacing on all Legendary wheels is 4 1/4". Bolt pattern 5 x 4.5 NOTE* These Legendary wheels require Legendary lug nuts. Check out our video on Legendary Wheels below: ...

Used compressed gas cylinder for a 1967-1973 Mercury Cougar or Ford Mustang. Later design canister is about 2-7/8" inches in diameter, slightly larger than the OEM 1968-70 version. These will be mostly empty and for display only. OEM cylinders are approximately 2-13/16" thick. These cylinders are very close to propane or Map gas cylinders in construction. Paint one red, and slap a cardboard sleeve with a reproduction decal and close the trunk lid. Dust cap may or may not be included,...

Used grommet for protecting the trunk light wiring as found on 1967-70 Mercury Cougar and Ford Mustangs. Ford part number C4AB-14603-A.

Bracket tack welded in the trunk to reinforce the rear structure for mounting the rear bumper. Ford part number C7ZZ-17B862-A, fits all 1967-68 Mercury Cougar and Ford Mustang. These are sold individually, these are not side specific. There is also a reproduction version available. Used part cut from a 1967-68 Mercury Cougar, some spot welds will need to be drilled out on your end. Picture shows approximately what you will receive. 

These brackets weld in the trunk to reinforce the rear structure for mounting the rear bumper. Ford part number C7ZZ-17B862-A, fits all 1967-68 Mercury Cougar and Ford Mustang.Sold as a pair and are not side specific. 

Very nice reproduction of the ram air flapper vacuum motor. Application 1968-1/2 428CJ Cougar and Mustang, 1969-71 Mercury Cougar with ram air, and 1969 Ford Torino 428CJ ram air. Not for shaker ram air systems.NOTE: These are manufactured with an extra long shaft to allow you to trim for an exact fit.

Concourse correct reproduction chrome GT air cleaner lid for the Mercury Cougar and Ford Mustang equipped with either the Boss 302, GT 390, or 428 CJ engine without the shaker option. This is an extremely hard piece to find used, and even rarer in NOS form, but now we can offer you this new unit that is made from the original tooling! It was possible to order a 390 GT motor for your Cougar without ordering the 390 GT package. Cougars equipped with the S code 390 6.5 Litre engine,...

Quality reproduction of the 1968 - 1970 CJ Mercury Cougar, 1969 - 1970 Shelby GT500, 1968 - 1969 Cyclone, Ford Fairlane, Ranchero and Torino 428 Cobra Jet Ram Air cleaner base. Features correct snorkel opening and breather elbow.Replaces Ford part number C9ZZ-9600-E or C8ZZ-9600-A.

This air cleaner is the early style with a vacuum actuated valve. 289-2V , 302-2V, and 302-4V engines prior to 4/2/1968. Ford part number C8AZ-9A626-A.

This air cleaner is the late style without the vacuum actuated valve. Mid year it was changed to a thermal activated valve. After 4/2/1968. 289-2V , 302-2V, and 302-4V engines after 4/2/1968. Ford part number C8AZ-9A626-D. Click on images to enlarge. ...

Air cleaner intake assembly or snorkel specific to the one year only 390-2V premium fuel engine, (X code engine). This version has the thermally operated trap door. There was an early version that used vacuum to open the trap door to the heat stove. Ford part number C8WY-9A626-A. *Note - This snorkel has a different spacing on the mounting ears, it will not mount to a 390GT air cleaner base.

Quality recreation made from original parts. Decent reproduction, slightly different than the original Ford version. The noticeable difference is the lack of square notch in the slop joint. Ford part of C8OZ-9A626-C. This snorkel comes to you in primer.

Concours Correct Spring attaches snorkle thermo door to Snorkle Base Replaces Ford Part # C8AZ-9A652-B

Air cleaner intake assembly or snorkel specific to the one year only 390-2V premium fuel engine, (X code engine). This version has the vacuum operated trap door. There was an more common thermal version that used temperature to open the trap door to the heat stove. In most cases the vacuum valve will not be working. Most people are probably better off with the thermal version. We do not know the change over date. Ford part number C8WY-9A626-A. *Note - This snorkel has a different spacing...

This air cleaner is the late style without the vacuum actuated valve. Mid year it was changed to a thermal activated valve. After 4/2/1968. 289-2V , 302-2V, and 302-4V engines after 4/2/1968. Ford part number C8AZ-9A626-D. NOS new old stock. ...

C8AZ-9A603-C metal shroud and tube assembly that attaches to the factory 1968 air cleaner assembly on all C code 289-2V engines as well as F code 302-2V, and J code 302-4V engines all for 1968. We do not believe that this set up came with the Canadian export Cougars, those 1968 Cougars should have the closed PCV system, much like the 1967 49 state Cougars.Do to age and their location our used risers will have rust and or be very thin in spots. Reproduction version of this part is no longer...

If you are not looking to match the part numbers of your original hinges, we recommend considering our PREMIUM quality reproduction that is made of thicker material than the originals for added durability and is far superior to any previous reproduction. This listing is for you folks out there who want the correct part number on your hinge. Good used OEM original hood hinges that are available individually or as a set.   We carefully inspect these hinges before sending them...

This is for you folks out there who want the correct part number on your hinge. Good used OEM original hood hinges that are available individually or as a set. We now offer a PREMIUM quality reproduction that is superior to any other reproduction. We carefully inspect these hinges before sending them as used hinges are prone to wear in more than one area. Here is a helpful youtube video that shows you how to adjust your hood. Shipped with the spring. These will also work on 1967-70 as well....

This is for you folks out there who want the correct part number on your hinge. Good used OEM original hood hinges that are available individually or as a set. We now offer a PREMIUM quality reproduction that is superior to any other reproduction. We carefully inspect these hinges before sending them as used hinges are prone to wear in more than one area. Here is a helpful youtube video that shows you how to adjust your hood. Shipped with the spring. These will also work on 1967-70 as well....

Used passenger side (right hand) upper rear fender brace that brace visible when you open the door and look in the upper part of the fender void. Bolts to the cowl on 1967-68 Mercury Cougar and Ford Mustang. Ford part number C7ZB-16A006-A passenger side, C7ZB-16A005-A driver side.

Improved reproduction right and left hand hood hinges for the Mercury Cougar and Ford Mustang. Much heavier duty compared to the originals, thicker metal and slightly wider hinge bars. These hinges weigh 4.35 lbs, originals weigh 3.2 lbs. Hood hinge rivets have the 'plus' markings like seen on the 1969-70 hinges. Save your hinge springs, these do not come with the new springs. it will be easier to fit and adjust these hinges prior to installing the springs on them. We use an old section of...

Improved reproduction right hand hood hinge for the Mercury Cougar and Ford Mustang. Very heavy duty compared to the originals, thicker metal and slightly wider hinge bars. These hinges weigh 4.35 lbs, originals weigh 3.2 lbs. Hood hinge rivets have the 'plus' markings like seen on the 1969-70 hinges. Save your hinge springs, these do not come with the new springs. It is easier to fit an adjust these hinges without the springs installed on them. We use an old section of seat belt for removing...

Improved reproduction left hand hood hinge for the Mercury Cougar and Ford Mustang. Very heavy duty compared to the originals, thicker metal and slightly wider hinge bars. These hinges weigh 4.35 lbs, originals weigh 3.2 lbs. Hood hinge rivets have the 'plus' markings like seen on the 1969-70 hinges. Save your hinge springs, these do not come with the new springs. It is easier to fit and adjust these hinges without the spring installed on them. We use an old section of seat belt for removing...

Holds both both the speedo cable and the parking brake cable in place with two self tapping bolts. Bolts not included, picture is for reference only. Part will have rust, but not severe.Replaces Ford part number 381821-S2 per the Chassis Assembly Manual 1967 page 17, 1968 Page 39.

This is the first bracket to secure the emergency brake cable as it exits the firewall. It mounts to the frame rail. It is held on by one bolt which is not included, picture is for reference only. Part will have rust but not severe.

Used door hinge anchor plate for attaching the door hinge to the body pillar. Driver side lower only, marked with an "L". Fits any 1968 Mercury Cougar and Ford Mustang. Different than 1967 version, this one has a punched hole that looks like the State Utah. This hole locates the anchor plate, and is specific to the 1968 body. This plate will work on 1967 cars, and does fit the cast iron hinges too.Ford part number C8ZZ-6502639-A.

Used door hinge anchor plate for attaching the door hinge to the body pillar. Passenger side lower only, marked with an "R". Fits any 1968 Mercury Cougar and Ford Mustang. Different than 1967 version, this one has a punched hole that looks like the State Utah. This hole locates the anchor plate, and is specific to the 1968 body. This plate will work on 1967 cars, and does fit the cast iron hinges too.Ford part number C8ZZ-6502638-A.

Used door hinge anchor plate for attaching the door hinge to the body pillar. Driver side upper only, kind of shaped like the State of Arizona, marked with an "L". Fits any 1968 Mercury Cougar and Ford Mustang. Different than 1967 version, this one has a punched hole that looks like the State Utah. This hole locates the anchor plate, and is specific to the 1968 body. This plate will work on 1967 cars, and does fit the cast iron hinges too.Ford part number C8ZZ-6502667-A.

Used door hinge anchor plate for attaching the door hinge to the body pillar. Passenger side upper only, kind of shaped like the State of Arizona, marked with an "R". Fits any 1968 Mercury Cougar and Ford Mustang. Different than 1967 version, this one has a punched hole that looks like the State Utah. This hole locates the anchor plate, and is specific to the 1968 body. This plate will work on 1967 cars, and does fit the cast iron hinges too.Ford part number C8ZZ-6502666-A.

Reproduction pair of lower fender braces. The portion with the lip mounts vertically and the purpose of the lip is to align the splash shield into the proper location.

Must have for 69-70 convertible owners or anyone else who wishes to tighten up the notoriously weak front inner structure of the 67-70 Cougar / Mustang. All three of these easy to install upgrades are outlined in the BOSS 302 Chassis Modification book that is NOT included in this package. After you install this kit you will wonder how you could have possibly lived this long without it. Even if you already have the one piece export brace, the chances are it is the old ill fitting off-shore...

These are about half the weight of originals and do not look correct in any way. They are far better than nothing. Bolts to the left hand and right hand lower floor reinforcement panels. Bolts into place with 6 hex bolts 3/8-16 x 1-1/8" with washers. These were painted satin black from the factory. Replaces Ford Part # C5ZZ-7610962-A. The Ford description of this plate is "Plate - Front floor lower cross member". All 1969 - 1973 Cougar convertibles and all 1965 - 1973 Ford Mustang...

Usually ships in 3-5 business days. Replaces Ford Part #: C4DZ-7653337-A. This is a new part, not a rebuild, no core needed. Correct brackets for a Cougar, not a generic one size fits all application. 5 year warranty when used with automatic transmission fluid.

Exhaust manifold bolt / stud for mounting the heat shield on the passenger side. This is the shorter of the two stud bolts. See item 31171 for the short heat shield bolt. For all Mercury Cougar or Ford Mustang, Torino, Cyclone, etc. with Q or R code 428 cobra Jet engines with factory cast iron exhaust manifolds. We also sell the complete bolt kit for the CJ exhaust manifolds. 

Very hard to find, one year only part that is not currently reproduced. These came on 1968 Cougars equipped with the "S" code 390 and the "X" code 390. Must have for that show quality GT or XR7-G. *NOTE* Please keep in mind that our hard to find parts like this are not always competitively priced with what you will find on the open market at swap meets and private party sales. Our primary intent in listing these is for our customers to use this website as a resource to properly identify parts...

Very rare one year only heat riser "S" shaped metal tube that attaches to the heat shield on the passenger side front portion of the exhaust manifold. Correct for all 1968 Cougars equipped with the 390 cubic inch engine.Ford part number C8AZ-9652-A.

*NOTE: This item comes un-painted from the manufacturer.Very correct reproduction of an impossible to find part. The only difference I can detect is that this original weighs just an ounce or two more than the original. Click on images to enlarge. Customer feedback found at mercurycougar.net: Boy service is just not the same as the "good old"? days. I ordered a half a trunk load of parts and pieces from West Coast Classic Cougar and about 2 hours later got a phone call informing me that the...

*NOTE: This item comes un-painted from the manufacturer.Another spot on reproduction! Correct for CJ and SCJ.  Comes with brackets and hardware as shown. Click on images to enlarge. ...

C8AZ-9A603-C metal shroud and tube assembly that attaches to the factory 1968 air cleaner assembly on all C code 289-2V engines as well as F code 302-2V, and J code 302-4V engines all for 1968. We do not believe that this set up came with the Canadian export Cougars, those 1968 Cougars should have the closed PCV system, much like the 1967 49 state Cougars.Do to age and their location our used risers will have minor surface rust, but otherwise be in good condition. Reproduction version of this...

Exhaust manifold bolt / stud for mounting the heat shield on the passenger side. This is the longer of the two stud bolts. See item 41350 for the short heat shield bolt. For all Mercury Cougar or Ford Mustang, Torino, Cyclone, etc. with Q or R code 428 cobra Jet engines with factory cast iron exhaust manifolds. We also sell the complete bolt kit for the CJ exhaust manifolds. 382803-S

Good used L bracket that is not heavily rusted or bent. Passenger side is marked from the factory with an "R" and driver side is marked with an "L". The portion with the lip mounts vertically and the purpose of the lip is to align the splash shield into the proper location.

Good used L bracket that is not heavily rusted or bent. Passenger side is marked from the factory with an "R" and driver side is marked with an "L". The portion with the lip mounts vertically and the purpose of the lip is to align the splash shield into the proper location.

If you are not looking to match the part numbers of your original hinges, we recommend considering our PREMIUM quality reproduction that is made of thicker material than the originals for added durability and is far superior to any previous reproduction. This listing is for you folks out there who want the correct part number on your hinge. Good used OEM original hood hinges that are available individually or as a set.   We carefully inspect these hinges before sending them...

Coil hood hinge spring, 5-13/32" in overall length, 14 coils, coil diameter 1.899 inches. Sold individually, one per side. Other applications include:  1967-69 Mercury Cougar1967-70 Ford Mustang1965-69 Torino, Fairlane, Ranchero1965-70 Falcon 1965-66 Falcon Ranchero Ford part # C3OZ-16789-A. You can find the hood hinge apron nuts here.Anghel Restorations offers a very detailed breakdown of the differences in the Cougar and Mustang hood hinges. ...

Reproduction hood hinge spring for all 1967-69 Mercury Cougars and 1964-70 Ford Mustangs. Common on many Ford and Mercury cars, this spring has 14 coils like the originals. We've found these springs to be of lesser quality than the originals, and they will stretch over time and not hold the hood up very well. We highly recommend you stick with original OEM springs. No returns on these springs. Click here to see our listing for good used originals. Replaces Ford part # C3OZ-16789-A. You can...